HARLEY-DAVIDSON SPORTSTER MID-LENGTH INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-04-2012

download
1. Find and unplug the O² sensor wires from the wiring harness and remove the ZIPSTRIP holding front O² sensor wires to the frame. Feed the end of the wire through the frame so they are free from the motorcycle. Note: pay attention to wire routing for re-installation. 2. Loosen the heat shield clamps on both the front and rear head pipe to gain easier access to the mounting nuts. 3. Remove the two head pipe mounting nuts from the flange at the heads. 4. Remove the clamp bolts that mounts the rear head pipe to the belt drive cover bracket. 5. Remove the two bolts from each muffler body where they attach to the stock mounting bracket. Carefully remove the exhaust system from the motorcycle and set aside. 6. Using a 7/8″ wrench, carefully remove the O² sensors from the stock head pipes and save for re-use on your RUSH system. 7. Remove the drive belt cover and remove the bracket off the rear cover bolt, bracket will not be re-used. 8. Loosen the brake rod at the rear eyelet using a T-30 torx socket. 9. Remove the three mounting bolts and washers attaching the exhaust mounting bracket. 10. If equipped with mid-controls, remove right side foot peg before installing your new RUSH system.

Incoming search terms:

Harley Davidson 39 mm Front Spring Lowering Kit INSTALLATION PROCEDURE

0

Filed Under (Harley Davidson) by admin on 07-04-2012

download
1. Support the motorcycle so the front wheel is off the ground. Next remove the front wheel and fender. Remove the fork cap nuts and loosen the lower triple clamp pinch bolts. Remove the front brake caliper. Some models have a tapered end to the fork tube. Extra effort will be required to remove the tube from the crown. Loosen the top fork cap 1 to 2 revolutions. Use a soft wood block or similar tool (that will not mark fork cap finish) and tap down with mallet to loosen fork tube from its tapered fit in top steering crown. Make sure fork pinch bolts are loose. To completely remove fork of this style, unscrew the fork cap entirely. 2. Slide both fork assemblies out of the triple clamps. Unscrew the top fork tube plugs. Remove the plugs and fork springs. CAUTION: Fork caps are under spring pressure and could cause serious injury. Drain the fork oil by turning the fork assemblys upside-down. 3. Next, bottom the fork tube into the fork leg. DO NOT extend the tube while you remove the allen bolt on the bottom of the fork leg. Turn the assembly upside-down and shake the damper rod and rebound spring out of the fork assembly. Again, DO NOT extend the tube during this. Extending the tube could dislodge the internal bottoming cone, which fits on the end of the damping rod, making it very difficult to reinstall the damper rod without complete fork disassembly. 4. FOR 1″ REDUCTION IN FORK LENGTH: You must first measure the length of the O.E.M. rebound spring. Depending on the model of the motorcycle, the length will either be 1″ or 2″ long. A. If you currently have a 1″ rebound spring, you need to replace it with the 2″ long LA Choppers rebound spring (included in the kit), then reinstall the damper rod in the fork tube. B. If you currently have a 2″ rebound spring, you will need to add the 1″ long spacer, then reinstall the damper rod in the fork tube.

2001-2010 Harley-Davidson TCFI III Fuel Injection System Installation And Tuning Manual

0

Filed Under (Harley Davidson) by admin on 06-04-2012

download
1. Check the exhaust system. If you can insert a broomstick through the mufflers, you have the equivalent of open drag pipes and auto-tuning will fail. If applicable, read the section about exhaust considerations starting on page 11. 2. Check for updates. This tuning manual is for TCFI III units with revision 3.3 or higher firmware. Before proceeding, check our website at www.daytona- twintec.com for available updates for the TCFI firmware, accompanying PC based software, and documentation. 3. Tech support. If you have questions or encounter problems at any point during the installation process, please contact our tech support at 386- 304-0700. 4. USB interface. Read the USB interface instructions starting on page 17, install the USB drivers and configure the COM port. 5. PC Link software used for setup and engine tuning. Read the PC Link TCFI III instructions starting on page 19 and install the software. 6. Data logging software. Read the TCFI III Log instructions starting on page 34 and install the software. 7. TCFI Controller. Read the TCFI installation instructions starting on page 41 and install the TCFI unit. Make sure you install the green PC link jumper wire. 8. WEGO wide-band exhaust gas oxygen sensor interface. Read the WEGO installation instructions starting on page 42, install the WEGO unit and perform the free air calibration described on page 43. 9. Connect the USB interface cable between the TCFI unit and your PC. 10. Start the PC Link TCFI III software, use the Open File command, and open the appropriate setup file. Setup data files are provided in the program folder for typical engine applications. Refer to Table 3 on page 16 for details. Additional setup guidelines for aftermarket throttle bodies and larger displacement engines are given on page 9. 11. Use the Edit Basic Parameters command. Make any required changes such as estimated rear wheel horsepower, injector flow rating (refer to Table 1 on page 9), and RPM limit. You must set the vehicle speed sensor (VSS) frequency for your model. This affects speedometer/odometer scaling, idle RPM control, and turn signal

Incoming search terms:

HARLEY-DAVIDSON SPRINGER FORKS MOUNTING INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-04-2012

download
1. The shock mounts with the body up —shaft pointing down. The nitrogen fill valve can be positioned toward the rear of the motorcycle. 2. Make sure that both halves of the upper and lower bushings are in place. NOTE: Do not try to install the shock with only half of the bushings, as this will lead to poor performance and premature seal leakage. The amount of “float” in the bushing set is necessary to ensure smooth operation of the damper assembly. 3. It is easiest to install the shock when the forks are fully extended, however the shock can be installed with the bike on the kick stand. 4. Insert the body eye into the mounting channel on the fork crown. Rotate the shock down into the lower channel. NOTE: A thread locking compound such as Red Loctite 262 or other similar product should be used on the shock fasteners. 5. Install the upper mounting stud and nuts, finger tight. 6. Push the shaft up far enough to insert the lower mounting stud and nuts. This will take a little effort because of the gas pressure in the shock. 7. Torque the upper and lower shock mount nuts to 22 ft. lb.

Incoming search terms:

Harley-Davidson MINI-TACH GAUGE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2012

download
1. Refer to the Service Manual and follow the instructions given to remove the Maxi-Fuse. For ALL models, WITHOUT Maxi-Fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. -J03119 1 of Gasoline can drain fr om the carb uretor fuel line when disconnected from fuel valve fitting. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00256a) 2. For carbureted models: Turn the fuel supply valve to OFF. Remove the fuel line from the valve. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 3. For ALL models: Follow the instructions in the Service Manual to remove the instrument console from the fuel tank. 4. See FUEL TANK: REMOVAL in the appropriate section (Carbureted or EFI Engine) of the Service Manual for instructions to remove the tank. 5. For all models EXCEPT FLHR or 1986 and later FL Softail models with Chrome Headlight Nacelle Kit (Part Number 67907-96): Follow the instructions in the Service Manual to remove the headlamp housing. For FLHR models, or Softail models WITH the Nacelle Kit: Follow the instructions in the Service Manual and the mini-tach bracket kit (purchased separately) to remove the handlebar shroud.

2003-2004 Harley-Davidson V-Rod Power Commander Installation Instructions

0

Filed Under (Harley Davidson) by admin on 05-04-2012

download
1 Remove the seat, air box shell, and airbox cover. 2 Remove the left hand side cover by removing the 5mm allen bolt (Fig. A). Fig. A Fig. B Fig. C Remove this bolt Unplug the stock connector from the ECM Route harness from PCIII under frame rail PC connectors
5 Route the PCIII harness behind the stock wires (Fig. D). 6 Plug the connectors from the PCIII in line of the stock wiring harness and ECM (Fig E). 7 Tuck the two connectors in the lower right corner of the frame (Fig. F)

HARLEY-DAVIDSON 1984 – 1999 Evo/ 5-Speed & 1999 – 2004 Twin Cam Transmissions Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-04-2012

download
Illustrated Parts List Main Shaft Gear (Small Gear) (1) Special Tools (1 set): • 3/4″ Socket Adapter • Ring-Seat Tool • Spring Tapered Split Ring (2) Counter Shaft Gear (Large Gear) (1) Trap Door Gasket (1) Trap Door (1) .010 Shim /Spacer (20) Delrin Crush Washer (2) Wavy Washer (2) Bearing Lock Nut (2) Nylon Set Screws (4+1 spare) Trap Door Cover Gasket (1) * Not illustrated : Champion Super-lock compound : 0-ring for clutch cable (if needed) : .010″ feeler gauge (3/16″ wide) : Scotch Brite Pad

2006 – 2007 Harley-Davidson Softail Ultimate seats Installation Manual

0

Filed Under (Harley Davidson) by admin on 04-04-2012

download
1. Remove original seats from your bike. #2. Your new Ultimate seats install using the front seat side mount bolts and the passenger seat is bolted to the front seat and rear fender. Side mount hex nuts = 2. If your stock rider seat is a rear fender mount, install one of the hex nut inserts on each side of the frame if they are not in your bike frame already. #3. All the mounting brackets are already installed on your new seats. #4. Connect our passenger seat to the rider seat with the 2 new round head allen bolts ( 1/4″ x ¾”) #5. Use the 2 new supplied bolts to attach the rider seat to the bike frame, one on each side into the threaded inserts ( 1/4″ x ½”) pan Phillips head) #6. Use the other new bolt for the passenger seat rear bracket in the fender (1/4″ x ½”) pan head. Enjoy the ride again

Incoming search terms:

HARLEY-DAVIDSON TURN SIGNAL MIRRORS WITH CONVEX GLASS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 03-04-2012

download
STEP 1 Remove the stock mirrors. LEFT SIDE: STEP 2 Choose the longest Allen bolt from the hardware kit that passes through the hand control, a split lock washer, an internal tooth star washer, the turn signal mount (if applicable), and still provides maximum thread engagement in the mirror stem without bottoming out. Mount the mirror with the hardware listed above. (Place the star washer between the mirror stem and the hand control). RIGHT SIDE: STEP 3 If the turn signals are not mounted under the mirror, proceed in the same manner as the left side. STEP 4 If the turn signal is mounted under the mirror proceed as follows: Apply Red loctite to the short threaded end of the special mounting stud. Screw this end securely into the mirror stem. -cont.- 1432-22HD-0105 TURN SIGNAL MIRRORS WITH CONVEX GLASS 1432 INSTALLATION Illiana CUSTOMER SERVICE 877.370.3604 (toll free) INSTALLATION QUESTIONS techsupport@kuryakyn.com or call 715.247.2983 WARRANTY Küryakyn™warrants that any Küryakyn product sold hereunder, if properly installed, maintained and operated under normal conditions, shall be free from any defects in materials and workmanship for a period of one (1) year from the date the Küryakyn products are sold to the customer. CONSEQUENTIAL DAMAGES: Küryakyn shall not be liable for any consequential or incidental damages. ABOUTOURCA TA LOG You’ll find all our innovations for H-D, GL and Metric Cruisers in our annual catalogs. Order online today-select the “CATALOGS” icon. Each Küryakyn™ product comes with a Proof-of-Purchase good for a complimentary catalog. Details in packaging. Be sure to ask your local dealer about other Küryakynproducts, the motorcycle parts and accessories designed for riders by riders. ©2004 Küryakyn USA™All Rights reserved.
STEP 5 Remove the turn signal assembly from the stock mirror. Pay close attention to how the stock turn signal ball joint assembly comes apart as this will aid in re-assembly. STEP 6 Place a star washer over the mounting stud and insert the mirror and stud assembly into the hand control. Re-assemble the turn signal ball joint being sure the turn signal light is aimed to your liking. You may wish to consult your H-D shop manual when re-assembling this ball joint. WIRING: STEP 7 Determine where you wish to splice into the H-D turn signal wiring harness. Cut the harness or strip back an appropriate amount to vinyl wire covering and prepare the wires for splicing. Make the wire connections as follows: Wires from Turn Signal Mirror H-D Turn Signal Wire Colors Black – (Ground) Black (Ground) Red – (Running Light) Blue (Running Light) White (Turn Signal) Violet (Turn Signal) If a more pronounced flash is desired, one may eliminate the running light function and wire as follows: Black Black Red and White together Violet If these turn signal mirrors are to be used in conjunction with stock front turn signals, no load equalizer will be required. If the turn signal mirrors are REPLACING stock front turn signals, in most cases, a load equalizer is required. For easiest access we suggest installing the load equalizer under the seat; tapping into the main wiring harness that leads to the tail lights and rear turn signals.

Incoming search terms:

Harley- Davidson Bagger Audio factory service manual for removal

0

Filed Under (Harley Davidson) by admin on 03-04-2012

download
POWER & SPEAKER HARNESS INSTALLATION- (Read electrical connections prior to connecting center power and ground wires) 1. Disconnect battery (negative cable first!) 2. Remove outer faring cover 3. Route long speaker wires from fairing area through tank channel to seat area. 4. Route one pair of speaker wires under each fender strut support; purple and purple and black wires to the right and green and green and black wires to the left. AMPLIFIER INSTALLATION- 1. Factory installed electronics will determine suggested placement of amplifier. 2. Position and attach amplifier to outer fairing support bars with supplied wire ties. (Electra/Ultra/Street Glide) BAGGER AUDIO™ LIDS INSTALLATION- Detach factory lid by removing the 2 screws holding the factory strap to inner lid and 5 small torque screws holding lid to factory latch assembly. (Consult factory service manual for further instructions) Remove metal strap from behind factory seal (This is the metal strap that the previous 5 small torque screws were removed from) Position metal strap in same location on your new lid. (If you purchased your product unpainted, you must install the supplied seal to your finished lid) Reattach BAGGER AUDIO™ LIDS by installing the 5 small torque screws in the same location as on the factory lid. (We suggest that you have an assistant hold the lid in place while attaching your new lids) Replace factory nylon Hinge straps with new nylon straps supplied in kit. Use metal straps and machined screws to secure the nylon hinge straps. 
 Place a small bead of silicone on the inside rim of the speaker basket to create a watertight seal between the inside of the lid and the speaker. 
 Install speaker into the bottom of the lid (not through the top opening) with supplied stainless screws and washers (4 per lid). Be sure to center speaker in lid opening to ensure proper speaker grill placement. Install speaker with terminals facing toward the front of the lid. One 1/4″ hole must be drilled in each bag. Holes can be positioned at the ownerʼs discretion. Place rubber grommet in drilled hole before running wires

Incoming search terms: