HONDA VTX1800R AND HONDA VTX1800N BIG SHOTS EXHAUST SYSTEM REMOVAL

0

Filed Under (Honda) by admin on 17-11-2011

download
If motorcycle is oxygen sensor equipped, unscrew the sensors from the stock exhaust system and install them
into the Vance & Hines exhaust system, being sure to install the front cylinder sensor into the lower pipe and
the rear cylinder sensor into the top pipe. Note: Use caution when handling. Do not touch sensor tip area.
2. If motorcycle is not oxygen sensor equipped, install both M12 x 11 plugs and washers (supplied)into the oxygen
sensor bosses. 3. Check condition of stock exhaust gaskets. Replace if damaged or worn. 4. Install and tighten supplied mounting bracket (stamped 345-P) in the original mounting bar location, using one M10 x 35 flange bolt and nut on top (supplied) and one M10 x 20 flange bolt on bottom (supplied) (Figure 2). Note: The bracket mounts behind the top frame mount and in front of the bottom frame mount(Figure 2).5. Install and tighten rectifier using M6x30 flange bolt, nut
and washer combinations (supplied) (Figure 2). 6. Place heat shields on a non-abrasive surface such as a blanket or carpet. Using a felt tip marker mark outside surface of front and rear heat shields with location of the mounting clips welded to the inside

Incoming search terms:

2002 Honda VTX 1800 R & S 3” BIG Straights Installation Instructions

0

Filed Under (Honda) by admin on 17-11-2011

download
Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove O2 sensors from each muffler and cover with supplied cap plug. 3. Loosen clamps at mufflers. 4. Remove bolts that are holding mufflers at rear mounting bracket. 5. Remove mufflers. 6. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 7. Remove rear pipe assembly. 8. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 9. Remove front pipe assembly. Hard-Krome Exhaust System Installation
NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to
replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design,
configuration and location. WARNING: Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessaryon a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system. 1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. (See Illustration) 3. Install Front exhaust header pipe, taking care to not scratch chrome surfaces on pipe, engine or motorcycle — use masking tape as needed

The Honda Ace/ Spirit 750 Lowering Kit from INSTATALLATION

0

Filed Under (Honda) by admin on 16-11-2011

download
The installation of the Scootworks Ace/Spirit Lowering Kit follows the same procedure as replacing the rear shocks. However, Scootworks wanted to assist you as much as possible with the installation process, and developed this instruction package. If there are any steps you feel need improvement in instructions, please email support@scootworks.com and specify the area you are having trouble with. Unpacking! The shipping container and contents must be inspected by the purchaser for damage to goods immediately upon receipt of goods, and a claim must be filed with the carrier if damage is discovered. The purchaser must contact Scootworks within 24 hours from receipt of damaged goods to file a claim, and for further instructions. Your Scootworks Ace/Spirit Lowering Kit will come packed with a left and right side lowering assembly, two large flat washers, two M8 x 1.25 hex head bolts, and these printed instructions

2007 Honda CBR600RR Power Commander Installation Instructions

0

Filed Under (Honda) by admin on 16-11-2011

download
Remove the bolt that holds the ground wires and bracket for the alternator connectors to the frame on the left hand side of the bike. This allows access to the Throttle Position Sensor connector. Unplug the stock wiring harness from the Throttle Position Sensor (Fig. F).Remove the main seat and the passenger seat. Remove the fuel tank cover. Remove the left hand fairing. Prop the fuel tank up. Lay the PCIII in the tail section temporarily and route the harness underneath the tail sec- tion (Fig. A). Removing the 4 bolts that hold the tail sectionb in place will make this easier Route the harness towards the throttle bodies (Fig. B) Attach the ground wire from the PCIII to the negative side of the battery.

HONDA CT110 SERIES MOTORCYCLE Cold engine Starting Procedure

0

Filed Under (Honda) by admin on 15-11-2011

download
Prime the engine before starting by cranking the engine several times with the kick starter. The ignition switch should be OFF, the choke lever Fully ON (A) and the throttle opened slightly. Flooded Engine If the engine fails to start after several repeated attempts, it may have become flooded with excess fuel. To clear the engine, turn off the engine stop switch and lower the choke lever to Fully OFF (B). Open the throttle fully and crank the engine several times with the kick starter. Turn the engine stop switch to RUN and open the throttle slightly; start the engine using the kick starter When service is required, remember that your authorized Honda dealer knows your motorcycle best and is fully equipped to maintain and repair it. The scheduled maintenance may also be performed by a qualified service facility that normally does this kind of work; or you may perform most of the work yourself it you are mechanically qualified and have the proper tools
and service data. • These instructions are based on the assumption that the motorcycle will be used exclusively for
its designed purpose. Sustained high speed operation, or operation in unusually wet or dusty conditions, will require more frequent service than specified in the MAINTENANCE SCHEDULE. Consult your authorized Honda dealer for ecommendations applicable to you individual needs
and use

Incoming search terms:

HONDA XR/ CRF100 120 BIG BORE KIT INSTALLATION AND REMOVAL INSTRUCTIONS

0

Filed Under (Honda) by admin on 15-11-2011

download
nstallation of this bore kit is identical to OEM installation. Please re- fer to the Honda shop manual or a qualified machanic for assistance. Note that the larger valve relief in the piston dome is the intake side (it should be installed closer to the rear of the bike). Every effort has been made to insure the quality of this product. Because BBR cannot control the installation or use there is NO warranty or guarantee with this product. Using quality motor- cycle oil will help prolong engine life. Be sure to change it often This kit is intended for use on 1993 and newer XR/CRF100′s using CDI ignition. Engine assembly requires special attention to detail. A new BBR Cylinder and piston kit have been supplied. The following measurments are critical to proper installation and performance

XR/ CRF100 120 BIG BORE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 14-11-2011

download
Installation of this bore kit is identical to OEM installation. Please re- fer to the Honda shop manual or a qualified machanic for assistance. Note that the larger valve relief in the piston dome is the intake side (it should be installed closer to the rear of the bike). Every effort has been made to insure the quality of this product. Because BBR cannot control the installation or use there is NO
warranty or guarantee with this product. Using quality motor- cycle oil will help prolong engine life. Be sure to change it often.

HERO HONDA CD-100 / SS100 / SLEEK / SPLENDOR / PASSION

0

Filed Under (Honda) by admin on 14-11-2011

download
1500 91255-169-003 30-42-11 FRONT FORK SEAL (S/S) (SLEEK) Improved Quality 200 20 PCS
1500A ————— SET OF 2 PCS FRONT FORK DUST SEAL (S/S) 100 10 PCS 1501 90756-198-000 7-37-7.5 FRONT FORK TRIPLE (COLLER) (CD-100) 200 20 PCS 1502 91202-302-01013.8-24-5 KICK SHAFT 200m20 PCS 1502A 91202-302-010m13.8-24-5+1514 KICK SEAL(SPL.GRADE O.E TYPE) MATERIAL WITH PUCH ROD RUBBER 100 10 PCS 1503 91205-350-000 6-25-6 CLUTCH 200 20 PCS 1504 91202-GK4-722 18.9-30-5 MAGNET
200

Incoming search terms:

HERO HONDA CD100 CHHEDA ELECTRICALS & ELECTRONICS INSTALLATION

0

Filed Under (Honda) by admin on 13-11-2011

download
These are intelligent CDI’s using variable-advanced timing where the firing angle is varied according to the engine RPM in order to maximise both the power output as well as the engine efficiency.
Built with the latest technology and infrastructure to offer high reliability and superior performance.

Honda CB100 engine INTRODUCTION

0

Filed Under (Honda) by admin on 13-11-2011

download
Fuel Injection System for One Cylinder Motor Cycle Engine. Fuel injection has been developed for many years. But its common application is limited on car’s engine. With many reason fuel injection systems in motorcycle one cylinder engine has not been widely used yet. Fuel Injection System allows the amount of fuel, injected to be controlled appropriate to engine parameters such as engine speed, amount of air inducted to cylinder, temperature, for each cycle, over the entire engine operating conditions. This fuel injection research is done to find out the Volumetric Efficiency of the intake manifold system, the amount of fuel need to be injected for each engine cycle, and the engine characteristics over variation of test conditions. This research based on Honda CB100 engine, at applied thermodynamic Laboratory of Mechanical Engineering Department, Faculty of Engineering University of Indonesia. Experiment data from this
research shows the characteristics of injector duration as functions of engine speed, intake pressure, on one cylinder engine and the results of this research shows a good Volumetric Efficiency of the intake manifold designed using CFD (Computational Fluid Dynamic)

Incoming search terms: