Honda GL1500 Gold Wing Motorcycles Trike Conversion Installation Guide

0

Filed Under (Honda) by admin on 19-12-2011

download
Secure and raise motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. • Left and right side-covers (to be re-installed with minor modification). • Seat (to be re-installed without modification). • Trunk. • Left and right passenger foot rests (to be re-installed without modification). • Left and right side-covers above passenger foot rests. • Battery and holder (to be re-installed without modification). • Left and right saddle bags (retain side cover mounting grommets for re-use). • Left and right mufflers. • Rear wheel. • Rear brake line to master cylinder.** • Reverse resistor assembly (to be relocated). • Swing Arm (Drive shaft boot will not be used). • Bank angle sensor. • Shocks. Air shock (non coil-over) to be reused. ** Thoroughly vacuum drain rear brake system, including feed line to left front caliper Modification to Trunk / Luggage Stay Removal from vehicle frame is not necessary. a. Cut the down tubes of the trunk stay and remove the lower section as shown in Figures 1 & 2 b. Trim rear upper tube-end rounded corners just outboard of welded nut. Trim line should be parallel with center line of vehicle. This will provide clearance for body when installed. Figure 2 (Inset) c. Remove the Hazard and Turn Signal relays from the center holder; bend Relay Holder Tab up 90°. Relays will be relocated to left and right sides. Figure 3

New Automatic Transmission for Motorcycles Human-Friendly Transmission

0

Filed Under (Honda) by admin on 18-12-2011

download
High-pressure fluid flow The engine rotates the pump swash plate, which has a gear mechanism. The rotating swash plate pushes the pump pistons to increase the pressure on the hydraulic fluid and feed it to the high-pressure annular chamber. The high- pressure fluid is then fed to the oil motor piston chamber where it pushes the pistons forward, which then push the motor swash plate. Power Fluid flow from pump to motor Fluid flow from motor to pump Low-pressure fluid flow The lower-pressure hydraulic fluid returns to the pump through the low-pressure annular chamber. In this way, the fluid circulates between the pump and the motor. Movement of distributor valves and pistons The distributor valves play an important role in fluid circulation. The valves are placed both in the oil pump and motor. When the pump pistons move to the compression side, the valves connect the piston chamber and the high- pressure chamber. When the pump pistons move to the expansion side, the valves allow a connection between the piston chamber and the low-pressure chamber. The valve in the oil motor moves opposite to its counterpart in the pump, ensuring the circulation of fluid within the system

Honda CRF/ XR50 Carburetor Kits, Air Filters INSTALLATION AND REMOVAL

0

Filed Under (Honda) by admin on 18-12-2011

download
The CRF/XR50 engineers never intended “large” people to be competitively thrashing their design. As a result, failed frames are becoming quite common at the track. Laid-out forks, tweaked, ill-functioning suspensions and bent frames are symptoms we’ve all witnessed. This CRF/XR50 frame kit addresses all these problems with not only a stronger framer but also with added knee-to-bar clearance for taller riders.. Features: • Heat-treated chromoly steel frame • TIG welded • Fully gusseted • Thicker-walled main tube that is also larger in diameter • Conservatively estimated at 4 times stronger than the stock unit • Race legal open cradle configuration, but with fully closed loop rear sub frame under the seat for added strength and safety • Stronger swing arm pivot area prevents wallowing • Frame is 1″ longer than stock, resulting in greatly enhanced handling characteristics This Chromoly 1″ longer frame with chromoly removable subframe is the off the hook! It features a detachable chromoly subframe with all hardware as well as a 1″ rise in gas tank and seat height for more more leg room and to allow bigger carburetor modifications. Extended frame also provides: • Much needed knee-to-bar clearance • Improved rider position • Better Center of Gravity • Better control Features: • Heat-treated chromoly steel frame • TIG welded • Fully gusseted • Thicker-walled main tube that is also larger in diameter • Conservatively estimated at 4 times stronger than the stock unit • Race legal open cradle configuration, but with fully closed loop rear sub frame under the seat for added strength and safety • Stronger swing arm pivot area prevents wallowing • Frame is 1″ longer than stock, resulting in greatly enhanced handling characteristics • Gas Tank is raised 1″ for added clearance

Incoming search terms:

Honda CARBURETOR ADJUSTMENT TOOLS

0

Filed Under (Honda) by admin on 17-12-2011

download
K&L CARBURETOR ADJUSTMENT WRENCHES These tools use tough and accurate bevel gear actuation instead of cable for professional use. The aluminum handle includes index marks for accurate tuning. Sold each. Three types available: 35-9653 Slot-type Pilot Screw Adjustment Wrench for Kawasaki/Suzuki/Yamaha 35-9658 Slot-type Pilot Screw Adjustment Wrench with longer tip for Kawasaki/Suzuki/Yamaha 35-9650 D-type Keihin Pilot Screw Adjustment Wrench for Honda 90-DEGREE 1/4″ HEX DRIVER This gear driven, 1/4″ hex driver set is made of high-grade aluminum and stainless steel. Strongest tool of it’s type on the market. Designed for use on hard-to-reach pilot air screws on inline fours. Can be used with any 1/4″ or 6mm hex bits. 35-7820 90-Degree 1/4″ Hex Driver Set: Includes straight slot, phillips, d-shape pilot screw bit, 6mm hex jet bit & 1/4″ – hex – 1/4″ drive bit. FCR CARB TOOL Set includes three bits – 6mm hex for main jets, long reach straight slot for pilot jets and 3mm allen for float bowl removal. Longer bits make this set ideal for reaching into recessed cavities when adjusting Keihin FCR carburetors. Sold as a set. 35-7978 FCR Carb Tool 12″ DRILL BIT For removal of carburetor plug. (mixture screw plug) 1/8″ bit x 12 inch length. 35-1186 YM-33217-16 JET DRIVER 35-2270 Perfect for removal of jets from small recessed passages

Incoming search terms:

2004 CBR 1000RR CYLINDER HEAD COVER INSTALLATION

0

Filed Under (Honda) by admin on 17-12-2011

download
COLOR TABLE MARCH, 2004 ©2004 American Honda Motor Co., Inc. 9 When ordering a colored part: 1. Confirm the color code for the required part from the color table according to the part name and color type. 2. Select the corresponding part number from the appropriate PAGE/GRID. 3. Parts marked “X” are unused. 4. “*” = Basic Part Number, no extension (i.e. ZA, ZB). CBR1000RR’04 2004 No. COLOR CODE BASE COLOR NH1 Black NH1 R258B Winning red R258 NH411B Force silver metallic NH411M A R E A DESCRIPTION BASIC PART NO. 1CLIP, PANEL FIXING 91549-MW0-790 ZA ZA ZA 2COWL (UPPER) 64211-MEL-000 ZA ZB ZC 3COWL SET, L. (LOWER) (WL) 64450-MEL-670 ZF ZG ZH 4COWL SET, L. MIDDLE (WL) 64350-MEL-670 ZA ZD ZE 5COWL SET, R. (LOWER) (WL) 64400-MEL-670 ZF ZG ZH 6COWL SET, R. MIDDLE (WL) 64300-MEL-670 ZA ZD ZE 7COWL SET, RR. SEAT (WL) 77210-MEL-010 ZE ZF ZG 8FENDER, FR. 61100-MEL-000 ZA ZC ZB 9FRAME 50100-MEL-670 ZAZAZAA 10 FRAME 50100-MEL-770 ZA ZA ZAAC 11LABEL, COLOR 87565-MEL-000 ZD ZE ZF 12MARK, COWL (LOWER) 64819-MEL-000 ZD ZE ZB 13MARK, L. TOP SHELTER 64852-MEL-000 — ZA ZC 14MARK, L. TOP SHELTER 64856-MEL-000 ZA — — 15MARK, MIDDLE COWL 64811-MEL-000 ZA — — 16MARK, R. TOP SHELTER 64851-MEL-000 — ZA ZC 17MARK, R. TOP SHELTER 64855-MEL-000 ZA — — 18MARK, RR. SEAT COWL 64841-MEL-000 ZA ZB ZD 19MARK, RR. SEAT COWL 64842-MEL-000 ZA ZB ZD 20RAIL ASSY., SEAT 50200-MEL-010 ZA ZA ZA 21SHELTER SET, TOP (WL) 83150-MEL-670 ZA ZD ZE 22STRIPE A, L. MIDDLE COWL 64814-MEL-670 — ZC ZA 23STRIPE A, R. MIDDLE COWL 64813-MEL-670 — ZC ZA 24STRIPE C, L. MIDDLE COWL 64817-MEL-670 — ZA ZB 25STRIPE C, L. MIDDLE COWL 64818-MEL-670 — ZA ZB 26STRIPE, L. TOP SHELTER 64854-MEL-000 — ZB ZB 27STRIPE, R. TOP SHELTER 64853-MEL-000 — ZB ZB 28STRIPE, WINDSCREEN 64805-MEL-000 ZA ZA ZA 29WHEEL SUB-ASSY., FR. 44650-MEL-000 ZA ZA ZA 30WHEEL SUB-ASSY., RR. 42650-MEL-010 ZA ZA ZA 31WINDSCREEN SET 64250-MEL-000 ZA ZA ZA

HONDA CR 500R/ 500AF Hi Power Digital Ignition AND Light Coil Installation Instructions

0

Filed Under (Honda) by admin on 16-12-2011

download
Place the motorcycle on a secure stand. 2.Remove the fuel tank and radiator shrouds. 3.Remove the front number plate if CDI unit is located behind number plate. 4.Remove CDI Ground from coil. 5. Remove Old CDI. 6. Remove ignition cover. 7. Use an electric, pneumatic impact to remove flywheel nut. 8. Use flywheel puller to remove flywheel. Thread the flywheel puller into the flywheel by turning the puller counter clockwise (left hand thread). Turn flywheel puller center nut clockwise with an impact set to low to remove flywheel. 9. Remove 2 bolts that secure the stator.
10. Remove stator. 11. Install new stator by aligning the index mark on the lower stator plate with the index mark on the left crankcase. 12.Install and tighten stator bolts to 9 ft-lbs. (1.2 kg-m). 13. Install new flywheel and tighten flywheel nut to 40ft-lb (5.5 kg-m). 14. The pulser gap is preset to .012″. If you have trouble starting you bike after installation confirm the gap between the pulser and the ignition trigger on the flywheel is .012″. Use a good/no good technique when checking and adjusting the gap. The largest feeler that will fit without forcing the feeler into the gap is the current gap. 15. If the pulser gap needs to be adjusted loosen the pulser mounting bolts adjust the pulser up or down as needed

Incoming search terms:

Honda CBR 400RR Service and Repair Manual

0

Filed Under (Honda) by admin on 16-12-2011

download
Once you have found al1 the identification nurnbers, record thern for reference when nbuying parts. Since the rnanufacturers change specifications, parts and vendors (cornpanies that rnanufacture various cornponents on the
rnachine), providing the ID nurnbers is the only av to be reasonablv sure that vou are buvina Model, c ~ d e and
production year CBR400RR-J (1988) CBR400RR-K (1 989) CBR400RR-L (t990 and 91) CBR400RR-N (1992 and 93) CBR400RR-R (1 994-on) , the correct parts. Whenever possible, take the worn pari to the dealer so direct cornparison with the new cornponent can be rnade. Along the trail frorn the rnanufacturer to the parts shelf, there are nurnerous places that the part can end up with the wrong nurnber or be listed incorrectly. The two places to purchase new parts for
your rnotorcycle – the accessory shop and the rnotorcycle dealer – differ in the type of parts they carry. While dealers can obtain virtually every part for your rnotorcycle, the accessory shop is usually lirnited to norrnal high wear iterns such as shock absorbers, tune-up parts, various engine gaskets, cables, chains, brake parts, etc. Rarely will an accessory outlet have rnajor suspension cornponents, cylinders, transrnission gears, or cases. Used parts can be obtained for roughly half the price of new ones, but you can’t always be sure of what you’re getting. Once again, take your worn part to the breaker for direct cornparison. Whetherhu~ng new, used or rebuilt parts, the best course is to dea1 directly with sorneone who specialises in parts for your particular rnake. Frame nwnber NC23-1020001 t0 1036454 NC23 t090001 t0 10981 16 NC29-1000001 to 101 0598 NC29-1050001 on NC29-l t00001 on Unofficial (grey) imports
All CBR400RR rnodels in the LIK are unofficial (grey) irnports frorn Japan. The rnajority are second-hand rnachines and are allocated age-related licence plates for UK use (the licence plate letter reflects the production year in Japan), although new CBRs are allocated current year UK registration letter plates. Cornrnon changes rnade prior to sale in the UK are the disabling of the rev-lirniter device (or more correctly ‘speed-lirniter’ device), which is fitted to cornply with Japanese rnarket regulations. The device is located inthe speedorneter head and is linked to th

Incoming search terms:

Honda, Polaris (2000 and older) ATV Thumb Warmer Installation Instructions

0

Filed Under (Honda) by admin on 15-12-2011

download
Hi/Low Switch Installation Choose a location for the switch, which is convenient and has sufficient rear clearance for the electrical connections and is within 18″ of a voltage-controlled wire (a wire in the lighting circuit). Drill a 1/2″ (13mm) hole and install the switch from the back. Leave the strain relief nut on the switch. On the front install the Hi/Low indicator tab and secure the switch and tab using the metal nut. The amount of switch barrel protruding can be adjusted by moving the strain relief nut. Wire Routing and Connections Route the electric cord along the handlebar to switchmarea and secure with supplied tie wraps, electrical tape, or both. Cut and strip to proper length. Attach a ground wire of sufficient length to go from the red wire to a good ground. WARNING: Lead wire slack in the area of the throttle must be neither excessive nor tight. Ensure no binding occurs when the throttle is open fully.,Soldering connections is the most durable method, but the following will provide years of service. Attach the 1/4″ female slip-on connectors to the white and blue wires and #10 ring terminal to warmer leads as shown in Figure 2. (A crimping tool works best, but a Vise Grips or pliers will work). Figure 2. Switch Connections (Option B) Connect the single yellow or red wire to a regulated (lighting) circuit using Option A (ATV has a switch in a lighting circuit with a 1/4″ tab) or Option B: Option B: Locate a power wire (usually yellow) leading to a headlight, taillight, or dash light (Figure 2). Using the red tap connector, place this power wire into the continuous channel and insert the red wire (do not strip insulation) completely to stop in the second channel. Make the connection by squeezing (w/pliers) the metal contact until flush with the top of the connector. Close the hinged cover until latched. Complete connections to switch and ground circuit.

1989-2000 Honda XR’S WHEEL REMOVAL AND SERVICE TOOLS

0

Filed Under (Honda) by admin on 15-12-2011

download
ATV BALL-JOINT SOCKET This tool is designed remove and install nut on Yamaha YFM350X Warrior. 35-8581 ATV Ball-Joint Wrench ATV BALL-JOINT SEPARATOR This tool is designed to separate the knuckle-ball joints on ATV’s without damage to the A-arm, ball joint stud or rubber boots. Sold as a kit with two separate press bolts to fit a variety of applications. Fits the following ATV applications: HONDA: TRX250R 86-89, TRX250X 87-88 & 90-91, TRX300EX 93-98 YAMAHA: YFZ350 Banshee 87-02, YFM350X Warrior 87-96 35-1975 ATV Ball-Joint Separator

Honda TRX 400EX INSTALLATION And REMOVAL INSTRUCTIONS

0

Filed Under (Honda) by admin on 14-12-2011

download
Quiet cores are supplied with this kit but not installed. To install the quiet cores remove both rear end caps ((turn downs) and install the quiet cores with the tubes facing inward. Re-install the end caps. REMOVAL Remove seat, disconnect attery and remove. Remove front fenders and side skirts. Remove fuel tank (make sure to shut fuel off and drain remaining fuel in the line before removing). Remove stock muffler first, then remove stock headers. Retain the 4 stock header bolts to install on your new exhaust system. Remove the rear bolt from your stock air box. Loosen stock intake clamp at carburetor. Remove stock boost bottle from the side of the boot. Loosen stock snorkel clamp at the air box, remove stock retaining clip at the front of the snorkel. Remove stock air box, intake boot and snorkel together from the ATV. Slide tarter solenoid off of stock mounting prongs. Remove Phillips screws from fuse holder and remove from plastic housing. Remove plastic battery housing from the ATV. Unplug tail light from harness. Unclip harness from the 2 clips above the battery. CARBURATION Now would be a good time to replace your stock main jet, with the supplied 190 main jet and replace your stock pilot jet with the supplied 48 pilot jet. Make certain that all hoses are tight and routed as stock. Be certain carb clamp is tight when re-installed. INTAKE BOOT Remove the intake boot from the stock air box. Take an exacto knife or razor blade and trim off the rubber piece that the hard plastic snorkel slips into. Trim around the intake boot staying the same distance as the rest of the lip. Take a hax saw and cut the groove as the rest of the boot is, being
careful not to cut all the way through (Picture Fig.2).