1998-2001 HONDA VFR 800 Complete Brake Line Kit INSTALLATION

0

Filed Under (Honda) by admin on 14-12-2011

download
Identify the key components that complete our brake line kit: You should have nine (9) hoses, one (1) double banjo bolt, fourteen (14) single banjo bolts, (1) single bleeder bolt three (3) drawings, and a picture CD. There are also a total of forty (40) washers and two (2) “olive” conic inversors. Thirty six washers will be used, and two olives. The rest are spares.Step 2: Familiarize yourself with the brake lines, which are labeled for application. Lettered brake hoses A, B, C, D, E, F, G are installed on the front of the motorcycle, while brake hoses (H and I) are installed on the rear. Each label will reference a different drawing, which will show you the location of the key brake system
components.Step 3: To ensure no paint damage from a brake fluid spill, completely cover the bike. This process can be messy, and brake fluid WILL drip! Step 3: Dry out (bleed) your OEM hoses, and take note of how the stock system is installed. You may want to take a couple pictures, in case you need to re-install. Step 4:Remove the stock hoses on the front of the motorcycle, and replace with Galfer hoses labeled A,B,C,D,E,F,G. Locate lines A. this hose will run from the master cylinder down to the right caliper and across the fender through the C-CLIP down to the left caliper. Line D. will run from the (DELAY VALVE) up through the C-CLIP to the right side upper frame female fitting will thread into the male with a (OLIVE) this O.E.M tubing travels to the proportion valve. Line F will run from the left caliper up through the C-CLIP to the left upper frame female fitting and thread to the male with a (OLIVE) this tubing travels to the rear master cylinder. Locate and install line E; this hose will run from the lower delay valve down to the right caliper. locate and install line C& G; line G will travel from the bottom (left) mounting point on the left caliper, to the upper inner mounting point of the left caliper this line joins line C with a double banjo bolt. line C will travel from the inner left caliper through the C-CLIP across the front fender to the inner mounting point of the delay valve

Honda Foreman 500 And Honda Rubicon WINCH MOUNTING KIT INSTALLATION

0

Filed Under (Honda) by admin on 13-12-2011

download
Begin by removing the front skid plate located on the front of the ATV. Remove the four side 8mm bolts and four bottom 6mm bolts securing the front skid plate, figure 1. Save the fasteners as they will be used later to reinstall the front skid plate. 2. Remove the four plastic rivets on each side of the front plastic fascia, figure 2. Use a large screw driver to carefully remove the center rivet. After removing the center rivet, remove the rivet housing. Save the fasteners as they will be used to reinstall the front plastic fascia. 3. Remove the two 6mm bolts that attach the front plastic fascia to the bumper, figure 3. Remove the front plastic fascia at this time . Remove the two 6mm bolts that attach the front bumper to the plastic headlight assembly, figure 4. Save the fasteners as they will be used to reinstall the front bumper. 5. Remove the two top 8mm bumper bolts that attach the front bumper to the front rack, figure 5. Save the fasteners as they will be used to reinstall the front bumper. Figure 5 Remove Top Bumper Bolts Remove (both sides) 6. Remove the two ottom bumper bolts that attach the bumper to the bottom of the vehicle frame, figure 6. Save the fasteners as they will be used to reinstall the front bumper

Incoming search terms:

2001-2003 HONDA GL1800/ A ECM Replacement/ Cooling System

0

Filed Under (Honda) by admin on 13-12-2011

download
Use the Cylinder Head Inspection Kit for the Cyl- inder Head Inspection procedure. Use the kit for each GL1800/A you inspect. Do NOT dispose of kit items. 1) 19X20 mm cap (2) (cap B) 2) 8X15 mm cap (cap A) 3) Hose plug 4) Bottle/cap w/feed hose 5) Harness clips (10) 6) Harness tape 7) Inspection mirror A limited number of additional Cylinder Head Inspection Kits are available: call TechLine at 800-421-1900, ext. 1 if you need one. Kit con- tents are NOT available separately as parts. NOTE: • The following late ‘03 models do not have nto have their cylinder heads inspected: • Perform the following procedure with the engine at room temperature. • Both Left and Right cylinder heads must be inspected. • Use the Cylinder Head Inspection Kit for the following procedure. 1. Remove the front lower fairing. (See S/M, 2-6) 2. Remove and suspend the rear brake reser- voir, being careful not to stress the brake hose. (See S/M, 15-A-8)

Honda TRX 450R BoonDocker Nitrous System Installation Instructions

0

Filed Under (Honda) by admin on 12-12-2011

download
This nitrous manifold greatly simplifies the way extra fuel is delivered that is needed for nitrous use. The carburetor vents
are connected to this manifold, allowing the carburetor(s) to breathe normally through the airbox when nitrous is not used.
When nitrous is sprayed, the manifold produces a positive pressure that goes to the carburetor float bowl, which “pushes”
more fuel through the main jet of the carburetor(s). This eliminates the need for an extra fuel pump, fuel solenoid, extra
plumbing, and nozzle(s) that are necessary to inject the extra fuel in other systems.This manifold is also designed to vary the float bowl pressure in relation to nitrous pressure, thus keeping the nitrous and fuel delivery in sync. Fluctuations in bottle temperature greatly affect nitrous pressure, which affects nitrous delivery. By automatically adjusting the fuel delivery as nitrous pressure varies, this manifold makes nitrous safe, reliable, and easy to use. The valve shown in picture (A) will require both the 4an x 1/8 npt fitting and the 1/8 npt plug. The valve shown in picture (B) will only need the 4an x 1/8 npt fitting. Use thread sealant on these fittings, be sure not to get any sealant inside the valve. Remove the upper mounting bolts on the front bumper. Install bracket support strap and reinstall the mounting bolts. 2. Install rear strap mounts over frame tubes. 3. Attach saddle bracket to support brackets, front and rear using supplied hardware.

HONDA WINCH MOUNT KIT REMOVAL AND Installation

0

Filed Under (Honda) by admin on 12-12-2011

download
Remove the front Plastic Bumper Guard. Remove the U-Bolts from the Winch Mount Plate and place the Winch Mount Plate on top of the horizontal bumper support tubes as shown in picture below. The U-Bolts will be placed around the tubes and up through the plate and are secured with Nylock Nuts. Tighten Fully. (Pictured Below). Mount the Winch to the underside of the Winch Mount Plate using the mount holes in the plate and the provided bolts. Tighten hardware at this time. 3. Using the two 5/16” x 1” bolts supplied with kit, mount the Winch to the Winch Mount Plate. Be sure that when the Winch is mounted to the ATV, the Winch Motor is on the RIGHT side of the machine. 4. Place the front Plastic Bumper Guard back onto the ATV, place the Roller Hawse Mount Bracket against the front Plastic Bumper Guard using the 7/8” Steel Bushings as spacers. Attach using the 6 x 30mm Bolts and Flat Washers. See picture on next page 5. String the Cable through the hole in the Hawse Mount Bracket. Remove one of the long rollers and the two side rollers of the Roller Hawse and feed the winch cable through the Roller Hawse. Reinstall the rollers and be sure rollers move freely.

2003 Honda RinconATV Plow Mounting Kit REMOVAL AND INSTALLATION

0

Filed Under (Honda) by admin on 11-12-2011

download
SEVERE INJURY OR DEATH MAY RESULT IF YOU IGNORE ANY OF THE FOLLOWING. • Read the Plow Operator’s Manual, the Winch Operator’s Manual, and all warning labels before operating. • Operate ATV at a walking speed with the blade installed. Do Not exceed 5mph (8 km/h) even with the blade up. • Plow Cautiously, impact with a hidden or stationary object may cause the ATV to stop suddenly or go out of control. • Do Not operate the ATV on slopes greater than 10° with the plow installed. • Do Not stand or ride on the plow. • Stay clear of moving parts and joints. Keep others away when operating or adjusting plow. • Inspect the plow mechanism, fasteners, cable, and adjustments before
operating. Replace all worn or damaged parts before operating. • Lower the plow to the down position before leaving the ATV unattended

Honda 300 2×4 Lift Kit Installation Instructions

0

Filed Under (Honda) by admin on 11-12-2011

download
This product is designed for us e on ATVs on which additional ground clearance and fender clearance is desired. It is designed for utility type, slower-speed use on relatively flat terrain in deep mud or snow. Although we have many thousands of satisfied lift kit customers and over 400 franchised dealers selling and installing lift kits, purchasers should be aware that use of this product may increase the frequency of required maintenance, part wear, and will raise the center of gravity on your ATV increasing risk of roll-over on side hills, ditches or other steep terrain. We recommend that wider tires and/or wheel spacers be used to achieve a wider stance and to improve stability of the ATV. Riders should be advised that the handling characteristics of a taller ATV are different and require extra care when riding on side hills or off-camber situations. If you further raise the center of gravity by adding heavy loads to racks or seats, the ATV must be operated with care, at slower speeds or on relatively flat ground. Operation of an ATV with or without a lift kit, while or shortly after consuming alcohol or drugs, subjects the rider to the risk of serious bodily harm or possible death. This is compounded if the rider does not wear an approved helmet and other safety gear. High Lifter urges that all approved safety gear be worn when riding an ATV. If this is not what you expected, or is not consistent with your intended use, you should return the product immediately to the seller, before installation, for a refund of the purchase price; less any fees. After installation, product is warranted for 90 days for defects in workmanship and materials. Warranty is limited to refund of the purchase price or replacement of the kit, at the seller’s option.

Honda CG125 Owners Manual, and repair manual

0

Filed Under (Honda) by admin on 11-12-2011

download
The author of this manual has the conviction that the only way in which a meaningful and easy to follow text can be
written is first to do the work himself, under conditions similar to those found in the average household. As a result, the hands seen in the photographs are those of the author. Even the machines are not new: examples that have covered a consider- able mileage were selected so that the conditions encountered would be typical of those found by the average owner. Unless specially mentioned, and therefore considered essential, Honda service tools have not been used. There is
invariably some alternative means of slackening or removing some vital component when service tools are not available and
isk of damage has to be avoided at all costs. Each of the six Chapters is divided into numbered Sections. Within the Sections are numbered paragraphs. In consequence, cross reference throughout this manual is both straightforward
and logical. When a reference is made ‘See Section 5.12′ it means Section 5, paragraph 12 in the same Chapter. If another
Chapter were meant, the text would read ‘See Chapter 2, Section 5.12′. All photographs are captioned with a Section/paragraph number to which they refer and are always relevant to the Chapter text adjacent. Figure numbers (usually line illustrations) appear in numerical order, within a given Chapter. Fig. 1.1 therefore refers o the first figure in Chapter 1. Left-hand and right-hand descriptions of the machines and their component parts refer to the right and left of a given machine when the rider is seated normally. Motorcycle manufacturers continually make changes to specifications and recommendations, and these, when notified,mare incorporated into our manuals at the earliest opportunity.
We take great pride in the accuracy of information given in this manual, but motorcycle manufacturers make alterations and design changes during the production run of a particular n motorcycle of which they do not inform us. No liability can be ccepted by the authors or publishers for loss, damage or injury caused by any errors in, or omissions from, the information give

Incoming search terms:

HONDA ATV FOURTRAX 400EX REPAIR, INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 10-12-2011

download
Never carry a passenger on an ATV. * Never operate an ATV on any paved surfaces, including sidewalks, driveways, parking lots and streets. * Never operate an ATV on

Incoming search terms:

2007-2010 HONDA CBR 600RR DUAL CANISTER SLIP-ON INSTALLATION

0

Filed Under (Honda) by admin on 10-12-2011

download
Hyperflo must insist that this system be used for track and closed course use only. Professional installation is recommended. Before beginning installation, please insure your motorcycle exhaust and omponents are not hot and have had ample time to cool. Please insure the motorcycle has been secured properly and is on level ground. We recommend the use of a service table. Hyperflo offers professional installation help at 801.999.8183. • 2 CARBON FIBER CANISTERS
• 2 END TIPS  (Options: Classic or Billet Stylewith sound cores) • MIDPIPE • 2 SPRINGS • 1 CLAMP
• UPPER MOUNTING BRACKET WITH BLINKERS ATTACHED • LOWER MOUNTING BRACKET WITH TAIL LIGHT AND PLATE MOUNTS • BRACKET BOLT (8MM X 75MM 1.25T) • EXTRA STICKERS • 8 TERMINAL ENDS/BUTT SPLICES 20072010 HONDA CBR 600RR DUAL CANISTER SLIPON INSTALLATION INSTRUCTIONS IMPORTANT! PLEASE READ PARTS LIST
YPERFLO RECOMMENDS THAT YOU LABEL SMALL PLASTIC BAGGIES TO KEEP HARDWARE SORTED AS IT IS REMOVED.
HARDWARE SORTED AS IT IS REMOVED. 1. INSURE THE EXHAUST SYSTEM AND EXHAUST COMPONENTS ARE FULLY COOLED. 2. INSURE THE MOTORCYCLE IS STABLE ON KICKSTAND OR REAR TIRESTAND OR SERVICE TABLE. 3. REMOVE BOTH THE FRONT AND REAR SEATS. 4. REMOVE THE 4 BOLTS HOLDING THE TAIL FAIRING TO THE SUBFRAME AND REMOVE THE TAIL FAIRING. REMOVE 5. REMOVE TRIM PLASTIC JUST ABOVE RIGHT SIDE FOOTPEG. (REMOVE THE ONE BOLT AND UNCLIP) TRIM PLASTIC UNCLIP REMOVE 6. REMOVE LOWER FOOT PEG BRACKET AND REMOVE THE HEAT SHIELD BOLT. ALLOW THE FOOT PEG BRACKET TO HANG BY THE HOSE AND WIRES. REMOVE 7. REMOVE THE PASSANGER FOOT PEG BRACKET ON THE RIGHT SIDE.