KAWASAKI VULCAN 900 SLASH CUT STAGGEREDS INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 02-05-2012

download
1. Attach mounting bracket 440-P to frame using two stock fl ange head bolts used on stock upper bracket (Figures 1 and 2). 2. Remove head pipes and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark outside edge of each heat shield to show location of mounting clips that hose clamps will loop through (Figure 3). 3. Lay front header, and rear header into their head heat shields and muffl er body heat shields. 4. Install #20 hose clamps (supplied) on heat shields and #36 (supplied) on muffl er body heat shields by feeding tail end of clamps into heat shield clips (fi gure 3). Take note of clamp screw head direction (Figure 4). Screw heads must be accessible when system is installed on motorcycle for adjustment purposes. NOTE: Do not tighten at this time. 5. Using stock fl ange nuts, carefully install head pipes into exhaust ports. Assistance may be required. NOTE: Do not tighten at this time. 6. Slide nut plates inside bracket that is welded to backside of muffl er bodies (Figure 5). While holding nut plates in place, attach muffl er bodies to mounting bracket 440-P using two 5/16″x 5/8″ fl ange head bolts (supplied). Leave them loose at this time. 7. Align muffl er bodies so they are level and parallel when viewing from the right side of the bike. Tighten cylinder port exhaust fl ange nuts on front and rear cylinders. 8. Tighten the fl ange bolts on both muffl ers. 9. Tighten all heat shield clamps. 10. Check for adequate clearance of all exhaust system components and motorcycle accessories prone to heat damage. NOTE: For models with fl oorboards, two Spacer washers are supplied to space out the fl oorboard bracket enough to allow the fl oorboard to fold up without hitting the heat shield. 11. Be sure to tighten all hardware before starting your motorcycle. 12. After installation and before starting motorcycle, completely clean pipes and muffl ers with cleaning solvent and a clean, soft cloth that will not leave a residue. NOTE: Any residue, oil, or fi ngerprints will stain the chrome when the metal heats up

Kawasaki Mule Roof 600, 610 and 4010 Trans Crew, Roof Installation Manual

0

Filed Under (Kawasaki) by admin on 02-05-2012

download
INSTALLTION INSTRUCTIONS – Mule 600/610 (4010 Trans skip to pg 4) 1. Place Roof Panel on top of UTV Roll cage and center front to back, and left to right. 2. Using Figure 1 Below – place UTV Roof Mounting Brackets around roll cage bar and using a marker, mark the position of the holes needed in the roof for each Roof Mounting bracket . Figure 1 Copyright 2007 DiamondBack Automotive Accessories, Inc. Page 3 3. Next, remove the roof from the roll cage and using a drill with 1/4″ bit, drill holes using the marks as a guide. 4. Cut (4) 3″ strips of adhesive foam and apply to roof in where mounting brackets are positioned to prevent roof rattling once mounted. Foam should run in the direction of the roll cage as shown in Figure 1 above. 5. Next, reposition the roof on the roll cage according to step 1. 6. Prior to attaching the roof mount brackets, cut the remaining adhesive foam in half and apply one section to the roof in the center of the roof where roof and each roll cage bar meet as shown in Figures 1 above. If additional tape is required to prevent rattling it can be purchased from any hardware store as window sealant foam tape. 7. Next, attach the roof mount brackets according to Figure 2. Use channel locks or pliers to hold top of carriage bolt and turn nut with 7/16″ socket.

Incoming search terms:

KAWASAKI KX450F SPARK XCR SYSTEM INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 02-05-2012

download
1. Place the machine on a stable work stand. 2. If you are not familiar with removing the original exhaust refer to the owner’s manual before you start work. 3. Always allow your machine to cool down before attempting to remove the exhaust. 4. Remove the two bolts from the right side panel. Then remove the side panel. 5. Loosen the stock mid-pipe clamp, then remove the stand-off bolt and bracket bolt that supports the muffl er. 6. Remove stock muffl er and clamp from the stock head pipe. 7. Slightly loosen the stock head pipe at the cylinder head to aid in aligning the parts. INSTALLING THE NEW XCR SYSTEM 1. Installer must use supplied hardware. 2. Slide mid-pipe onto head pipe. Rotate the mid-pipe slightly to obtain proper alignment with sub-frame mount. 3. Install the supplied M8x16mm bolt through sub-frame into the stand-off mount on mid-pipe (Finger tight). 4. Slide the muffl er onto mid-pipe, align muffl er mount with the stock muffl er mount hole, and install and fi nger tighten the OEM bolt. 5. Once you have the system fully aligned, install and tighten all the bolts securely to factory specifi cations. 6. Replace the side panel and secure the mounting bolts. 7. Re-tighten stock head pipe at the cylinder head. TEST RIDING 1. When you fi rst ride the bike be aware that the characteristics are often quite different so start out slowly. TUNING 1. On the KX450F, we suggest using stock jetting based on our testing condition. These specifi cations should only be used as a guideline. Riding at different elevations or climates may require using different settings to obtain peak performance. If you need additional assistance, please refer to your Kawasaki owner’s manual. 2. To convert system from Offroad to Competition specifi cations, remove the 5mm Allen bolt and Spark arrestor. Two different Db lowering inserts are also available (see accessories section on page 2). To return the system to Offroad specifi cation re-install the Spark arrestor into the rear of the muffl er using a small amount of blue thread locking compound (Loctite® 243) re-tighten the 5mm Allen bolt (6.5 ft pounds)

2003-2007 Kawasaki Ninja ZX6R/ RR HID Installation Removal Manual

0

Filed Under (Kawasaki) by admin on 02-05-2012

download
take out the original bulb and install the HID bulb. Be careful, do not touch the HID bulb at any time. Plug in the power wires into the original power plug. They go in easy and slide right in. Black wire connects into the black wire on the plug. On the right side, pink goes to red. On the left side, blue goes to red as these are positive wires. Pull the wires toward you slowly and carefully as you near the cover toward the headlight. Spin the rubber grommet if you need to line up the dust cover to the head light. Now lock it in. The arrow should point up if it is locked in properly. Left side installed the same way as the right. Mount the ballasts on the under side of the cowling covers with two nuts and bolts. Position the ballast in the proper place. Then, hold in one spot while drilling two holes for the bolts. An alternate mounting may be with industrial double sided tape or industrial Velcro. Do not use those cheap double sided tape of Velcro mounts as they will not hold the weight of the ballasts. Close up of underside of the cowling cover with ballast installed.
Top side of the cowling cover. Repeat installation on the second cowling. Then reinstall on the bike, connecting all the plug wires.

Kawasaki 900 / 1100 Engine Removal and Installation

0

Filed Under (Kawasaki) by admin on 01-05-2012

download
1.1 (Above) Remove the two retaining straps, disconnect the battery and remove it from the hull. Disconnect the negative (black) cable first, then the positive (red). Step 2 Intake Removal 2.1 (Below) Remove the eight 10mm bolts securing the flame arrestor cover to the base and remove it. 2.2 (Below) Pull out the flame arrestor screens. 2.3 (Below) Remove the six 10mm bolts securing the flame arrestor base and carbs to the manifold and remove the base. 2.4 (Below) Loosen the gas tank cap to relieve pressure. Be sure the fuel switch is turned to the “OFF” position, and be aware of any fuel that may spill from the hoses. Make sure the hull is clear of any gasoline fumes before continuing work, especially with power tools. Remove the pulse lines from the block, and the three oil lines from the carbs. Move the carbs aside in the hull. 2.5 (Below) Remove the 18 10mm nuts from the studs securing the intake manifold to the engine and remove the manifold

Incoming search terms:

Kawasaki Mule 2003 and newer Plow Mounting Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 01-05-2012

download
Prior to installing the plow mount the vehicle must be prepped. If not already done so, install a WARN winch kit. Roller fairlead that comes with the winch kit does not need to be installed. This kit comes with a special fairlead to be used with plow. 2. Begin by locating and removing the two rear bumper mounting bolts. See Figure 1 and 2. Figure 1 Location of bumper bolts to remove Figure 2 Remove bumper bolts, both sides Location of bolt to remove WARN® INDUSTRIES PAGE 5 72171 Rev A0 4. Loosely install the mounting brackets to the vehicle using the 7/16″ hardware in the rear replacing the bumper mounting hardware removed in step 2. Do not tighten. See Figure 4 and 5

Kawasaki Mule Duster Adhesive Hook Strip Installation Instructions

0

Filed Under (Kawasaki) by admin on 30-04-2012

download
Use the loop on the Duster as a guide to locate the Hook Strip on the front of the bed. Clean the area and install the Adhesive Hook Strip as in Step 1. Install Adhesive Hook Strip to Front of Bed Cut the Adhesive Hook Strip into six (6) pieces to match the loop sewn to the Duster. Use the loop on the Duster as a guide to locate the Hook Strip on the sides of the bed and the tailgate. Clean the areas with a 50% Water/Alcohol Solution. Peel the backing off the hook a little at a time and press it fi rmly into place. Install Adhesive Hook Strip Allow 72 hours for the adhesive to set. Avoid unnecessary fastening and unfastening of the Duster during this period. Open Bed Open the bed of the vehicle. Tailgate Adhesive Hook Strip Allow 72 hours for the adhesive to set. Avoid unnecessary fastening and unfastening of the Duster during this period. Secure Duster to Front of Bed Fasten the loop sewn to the front of the Duster to the Adhesive Hook Strip on the front of the bed

Incoming search terms:

Kawasaki ZX-14 TITANIUM SIDEWINDER EXHAUST Installation Instructions

0

Filed Under (Kawasaki) by admin on 30-04-2012

download
STEP 2: PRE-ASSEMBLE HEADERS, COLLECTOR, AND MID-PIPE TO INSURE PROPER FIT BETWEEN ALL PARTS: Brock’s Performance pre-assembles the exhaust system before it is shipped to your door. We ask you to this to insure there were no shipping damages incurred before you start disassembling your bike. A lot of our customers use WD-40 applied to the joints to ease assembly, adjustment, and/or disassembly. STEP 3: REMOVE ZX-14 RIGHT AND LEFT DASHBOARDS : The right and left dashboards are held in place by three fasteners (Figure 4) which are removed with a No. 4 hex head wrench. Note that all dashboard and fairing fasteners have thin plastic washers located between the fastener head and the plastic body work. Be careful to save the plastic washers. To avoid losing fasteners and washers it is recommended that the installer place them in a container once they are removed. STEP 4: REMOVE ZX-14 LOWER FAIRING : The lower fairing consists of separate right and left side panels, both of which should be removed. The locations of the bolts and plastic push pins holding the fairing in place are illustrated in Figure 5. Details are provided below. • The plastic push pins is located in the front of the fairing (3) , aft of the front tire, and holds the left and right panels together. Remove the plastic push pins using a thin blade screw driver to lift the rivet head. Then pull the rivet from the bodywork. This will release the right panel from the left panel. • Remove the lower fairing fasteners & washers (1 & 2) on the right fairing panel with a No. 5 hex head wrench. • Remove the upper fairing fasteners & washers (4, 5, & 6) on the right fairing panel with a No. 4 hex head wrench. • Note that the top of the fairing incorporates slots into which hooks at the bottom of the mid fairing (red bodywork) fit. These hooks are shown in Figure 8. Pull the bottom of the lower fairing panel away from the bike and then downward to clear the hooks from the slots. The right side lower fairing should now separate easily from the mid-fairing. • Repeat for the left side lower fairing

Kawasaki ZX-14 Installation And Removal Manual

0

Filed Under (Kawasaki) by admin on 29-04-2012

download
1) Tools needed: 36mm socket / 32mm socket / 5mm Allen wrench / cordless drill / tap handle / hammer / razor blade. 2) The frame bracket serves as the drilling guide and we provide the transfer punch, tap, drill and step by step instructions for a relatively easy installation. However, do not attempt this installation unless you are skilled enough and confident that you can drill and tap (2) holes in your frame. We’ve also provided a picture of what it will look like should you decide to sell this bike later on, with your stabilizer removed. Follow these guidelines and you’ll find it’s quite easy. 3) Some photos may not be your exact bike but depict the idea of what needs to be done. 4) It is important to use Blue Loc-tite on all fasteners if you expect them to stay tight. 5) Cover the gas tank area with something substantial to protect the paint, in case of a slip. An old sweatshirt works well. It’s cheap insurance to actually just remove the tank shroud to avoid an accident. 6) Remove the stock 36mm nut AND washer , that holds the top triple clamp tight. Make a note of how tight it is. 7) Install the new “triple clamp damper mount” (TC mount) over the steering stem allowing it to match the exact shape of the triple clamp, with the “machined register” (lip) indexing over the back of the triple clamp. (See photo). 8) Install the new 32mm aluminum nut supplied in the kit (without any washer) with the Hex drive facing up and torque to 65ft. lbs. or more. (Check your manual for the recommended torque setting of this nut). 9) There is a slight amount of play in the “register” that fits over the back of the triple clamp to allow for variations in castings from the factory. If the TC mount tries to spin clockwise during tightening, which can misalign the stabilizer ever so slightly, you can slide something thin, like the edge of a razor blade, between the register and the back of the triple clamp to space it “just right” for alignment during tightening (see photo). Once it’s tight the razor blade will be stuck, so gently turn the 32mm socket as though you were going to loosen the nut but don’t actually loosen it. It will relieve enough pressure to allow the razor blade to come out. Double check your alignment again. 10) Remove the front tank mounting Allen bolt. Retain the stock washer that’s part of the rubber grommet. 11) Temporarily install the frame bracket and be sure the outer feet are touching or are very close to the frame. On rare occasions, the casting on the head tube prevents the feet from making contact. On these rare occasions you may have to slightly file the inner side of those feet until the bracket sits down flush. Not sure on this one? Call us. (note: 2007-on bikes have a larger casting area and early kits will not fit these late model bikes. All current kits now fit 2006-on)

Kawasaki KVF650/ 700, KSV 700 Camshaft Installation Instructions

0

Filed Under (Kawasaki) by admin on 29-04-2012

download
Liberally apply assembly lube to every surface of the camshaft. Install the camshaft into the cylinder head (the lobes should be pointed down) and align the decompressor shaft dowels with the weight arms. Install one of the camshaft sprocket holder bolts and tighten to less than finger tight, you should be able to move the camshaft very slightly back and forth, roll the crank over until the other bolt hole is exposed and insert the sprocket bolt and tighten to less than finger tight. Install the cam chain tensioner assembly, do not install the spring, spring dowel, washer, and bolt. Using the spring from the cam chain tensioner very slowly push the tensioner shaft in until the cam chain slack has just been taken out, this is witnessed by the very slight lifting of the opposite end of the cam out of the cylinder head cam journal, do not over tighten the cam chain at this point, if you do, remove the tensioner assembly and retract the plunger again and start over. (If it stays too tight it will stretch the cam chain prematurely and cause cam sprocket damage when the engine is assembled) Roll the camshaft toward the back of the machine (clockwise) loading the sprocket bolts against the back of the sprocket bolt holes, while holding the camshaft in that direction, tighten the sprocket mounting bolt to 14 ft/lb of torque. Rotate the engine in the opposite direction that you rotated it earlier and align the TDC mark, tighten the other sprocket-mounting bolt to 14 ft/lb of torque. Verify the cam timing and crankshaft TDC marks are in alignment

Incoming search terms: