2006 KTM 250 SX-F 250 EXC RACING 400 EXC RACING 450 SX, XC, EXC RACING 525 SX, XC, EXC RACING, REPAIR MANUAL

0

Filed Under (KTM) by admin on 05-05-2012

download
Hot start lever (250 SX-F) If you pull the red hot start lever [1] during the starting procedure backward, a bore in the carburetor will be opened through which the engine may take in additional air. The result is a „lean” fuel-air mixture of the type needed for hot starts.
ENGLISH 7 OPERATION INSTRUMENTS » Headlamp switch (EXCUSA) In this model the headlamp is switched on with the pull switch [1] . Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right Starter button (EXC) Pushing the black starter button [2] will actuate the E-starter. Emergency OFF switch (EXC Australia) The red emergency-OFF switch [3] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [4] will actuate the E-starter. 2 3 4 5 6 Indicator lamps The green control lamp [5] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [6] lights up when the high beam is on

Incoming search terms:

2008 KTM 65 SX 65 XC OWNER'S MANUAL

0

Filed Under (KTM) by admin on 09-03-2012

download
SERIAL NUMBER LOCATIONS » OPERATION INSTRUMENTS » Chassis number The chassis number is stamped on the right side of the steering head tube. Enter this number in the field on page no 1. Engine number The engine number is stamped into the engine housing underneath the carburetor. Enter this number in the field on page no 1. Clutch lever The clutch lever [1] is located on the left side of the handlebar. The adjusting screw [A] is used to change the original position of the clutch lever (see maintenance work on chassis and engine). The clutch is hydraulically actuated and adjusts itself automatically. Hand brake lever The hand brake lever [2] is mounted on the handle bars on the right and actuates the front wheel brake. The adjusting screw [B] can be used to change the basic position of the hand brake lever (see maintenance work on chassis and engine). 1 A 2 B
ENGLISH 7 OPERATION INSTRUMENTS » Short circuit button The short circuit button [1] turns off the engine. When pressing this button, the ignition circuit is short-circuited. Filler cap To open it: turn filler cap counter-clockwise. To close it: put filler cap back on and tighten it by turning it clockwise. Install tank breather hose [2] without kinks. Fuel tap The fuel tap [3] is located on the left side of the tank. Opening the fuel tap: Turn the knob all the way to the left. Closing the fuel tap: Turn the knob all the way to the right. Choke The choke button [4] is located on the left side of the carburetor. Pulling the choke button all the way out opens a bore in the carburetor through which the engine can take in additional fuel, thus achieving the „rich” fuel air mixture needed for cold starting. Pushing the choke button back in closes the bore in the carburetor. Shift lever The shift lever is mounted on the left side of the engine. The position of the gears is shown in the illustration. Neutral, or the idle speed, is located between first and second gear

KTM EXC Enduro & SX Motocross REPAIR MANUAL

0

Filed Under (KTM) by admin on 06-03-2012

download
Thanks to a history of competition successes, particularly in off-road racing, KTM motorcycles enjoy a large and loyal following. Established in 1953, KTM (from Kraftfahrzeuge Trunkenpolz Mattighofen where founder, Hans Trunkenpolz, had his engineering works) went through difficult times in the early 1990s. After a takeover, the Austrian company emerged as KTM Sportmotorcycle AG and has gone from strength to strength in recent years. Mainstay of their range are their Enduro and Motocross models, the EXC and SX, and these are covered in the latest new manual from Haynes. Models covered are the 250, 400, 450, 520 and 525 EXC and SX with 4-stroke sohc engines, 2000 to 2007. Information has also been included on the SMR Supermoto versions and MXC/XC derivatives. Haynes Manuals for cars and motorcycles are so popular that 150 million have been sold worldwide. Lay them end-to-end and they would circle the globe at the equator! The new manual begins with essential pre-ride checks, competition prep and routine maintenance tasks before moving on to more major repairs. There are comprehensive, fully illustrated, instructions for overhauling the engine, transmission, brakes, suspension and electrical system. Useful reference pages include colour wiring diagrams, fault-finding charts and a comprehensive section on tools and workshop tips. Because all Haynes Manuals are based on a complete stripdown and rebuild, not only are the procedures written from first-hand experience, but there is information about special tools required for each job, and its complexity, plus Haynes tips for saving time and money. The new Haynes KTM EXC Enduro & SX Motocross Manual is the only complete manual for owners of these motorcycles.

Incoming search terms:

Ktm 690 SM/ SMC/ SMR/ Duke Removal and Installation weld slag

0

Filed Under (KTM) by admin on 04-03-2012

download
1. Each bike varies with regard to welds and gussets. Review the photos first to get the idea of what needs to be done. 2. These photos may not be your exact model but depict the concept of what must be done. 3. Block the front tire securely before removing the top triple clamp so the tire cannot move at all. See photos. 4. Support the rear tire also, just enough to keep tension on the front tire so the forks stay tight. 5. Warning: Once the triple clamp is loose, the forks can roll away from the bike AND it happens very quickly . 6. The main triple clamp nut adjusts the tension on the steering head bearings. Make note of its tension before removing and do not over tighten the nut. It should be seated just enough to take the play out of the bearing.. 7. The top of the gauge/light cluster is mounted to the top triple clamp. You have to take out 4 self tapping Phillips head screws to remove the gauge pod. There is one connector on the back side of that and then it comes off. Then there are two bolts that need to come out with an 8mm wrench to free the top triple clamp. 8. Loosen the triple clamp pinch bolt under the main nut and forks pinch bolts and remove the top triple clamp, taking note of how tight the main nut is, so you can re-tighten it to the exact amount. Remove the tin bearing shroud (cover) and rubber seal making note of how the seal goes on, (lips face downward). 9. Grease your bearings while you have them exposed. (Keep the grease off the area where our frame bracket mounts!). 10. The goal is to allow the frame bracket to clamp cleanly and squarely around the upper half of the head tube. 11. Review your individual bike’s welding characteristics at the head tube. You’ll notice on the head tube there is a “groove” machined 360 degrees around the head tube. Everything in or above this groove must be clean of welds or slag. If this groove is visible all the way around and no welding slag has extended upward into or past this groove, then you’re installation should be easy. Any welds extending into or above this groove must be filed away, but without changing the clamping area diameter. DO NOT file away the paint on the clamping area if possible. Spend a little more time filing carefully and your bracket will stay tight. 12. Each bike seems to have not only different welds, but slightly different gussets. Evaluate your individual bike to determine the best fit. The bracket must clamp squarely and cleanly to the area just above that groove and yet SIT FLUSH all the way around the diameter of the head tube as per the photo in the lower right corner. Do not allow the bracket to protrude above the seal seating surface. Use a flashlight to see up under the bracket where it’s hitting if it’s not Flush. This bracket has clearance cut into it to clear the backbone of the frame

Incoming search terms:

2004-2005 KTM 85 SX / 105 SX REPAIR MANUAL

0

Filed Under (KTM) by admin on 24-02-2012

download
TORING THE REPAIR MANUAL IN THE BINDER -Put the index (3.205.44) into the binder. -Put the front page of the repair manual (210×297 mm) into the transparent pocket provided for this purpose on the outside of the binder. -Put the spine label (170×45 mm) into the transparent pocket provided for this purpose on the spine of the binder. -Put the summary list of contents (150×297 mm) into the transparent pocket provided for this purpose on the inside of the binder or insert this page on the beginning of the manual. -Then insert the individual chapters of the manual between the sheets of the index according to the page number printed in the right bottom corner of each page. Example: page no. 3-5, 3 = chapter 3, 5 = page 5 All pages with a page number that begins with the digit 3, for example, must be put under the index heading „Chapter 3″. -Index sheets that have not been marked with a certain chapter are for your personal convenience. T he respective headings can be entered in the list of contents

2003 KTM RA 250 SX REPAIR MANUAL ENGINE

0

Filed Under (KTM) by admin on 08-02-2012

download
STORING THE REPAIR MANUAL IN THE BINDER -Put the index into the binder. -Put the front page of the repair manual (210×297 mm) into the transparent pocket provided for this purpose on the outside of the binder. -Put the spine label (170×45 mm) into the transparent pocket provided for this purpose on the spine of the binder. -Put the summary list of contents (150×297 mm) into the transparent pocket provided for this purpose on the inside of the binder or insert this page on the beginning of the manual. -Then insert the individual chapters of the manual between the sheets of the index according to the page number printed in the right bottom corner of each page. Example: page no. 3-5 3 = chapter 3 5 = page 5 All pages with a page number that begins with the digit 3, for example, must be put under the index heading „Chapter 3″. -Index sheets that have not been marked with a certain chapter are for your personal convenience. T he respective headings can be entered in the list of contents

2000-2003 KTM MXC / EXC Dual Sport Kit Installation And Removal Manual

0

Filed Under (KTM) by admin on 08-02-2012

download
00-’03 KTM 400/450/520/525 EXC & MXC Dual Sport Kit Installation Manual 1. Get a degree in Mechanical and Electrical Engineering. (Just kidding!) 2. Remove the seat, fuel tank, and side panels. Stock switch Bracket Photo 2 EXC – Unplug and remove the stock headlight. (Photo 2.) Unplug the stock three-pin taillight connector and pull the taillight wires back to the rear of the airbox temporarily. MXC – Remove the stock front number plate. 3. Make sure the stock battery is oriented in its mounting bracket as shown with the positive terminal on the left side of the bike (as viewed if sitting on the bike). If not, remove and spin it 180 degrees. Photo 3
4. MXC ONLY! (EXC skip this step.) Locate the stock lighting wiring harness zip-tied under the frame back-bone (See Photo 4). Remove the securing zip-ties and route this wiring forward to the area behind the headlight. Route along right side of frame using factory wire- guide clamp. 5. Brake Light Switch Installation: The KTM kit uses a hydraulic brake-switch. This requires replacing the rear master cylinder banjo bolt with a specially made switch. Installing the switch requires bleeding the brake. If you do not feel competent bleeding your rear brake, please refer this job to a qualified mechanic, as failure to do it correctly will make the brake inoperable. Remove the stock banjo bolt and replace with the hydraulic switch as shown. Make sure to install

KTM 250-525 SX, MXC, EXC RACING ENGINE REPAIR MANUAL

0

Filed Under (KTM) by admin on 07-02-2012

download
TM REPAIR MANUAL IN LOOSE-LEAF FORM STORING THE REPAIR MANUAL IN THE BINDER -Put the index into the binder. -Put the front page of the repair manual (210×297 mm) into the transparent pocket provided for this purpose on the outside of the binder. -Put the spine label (170×45 mm) into the transparent pocket provided for this purpose on the spine of the binder. -Put the summary list of contents (150×297 mm) into the transparent pocket provided for this purpose on the inside of the binder or insert this page on the beginning of the manual. -Then insert the individual chapters of the manual between the sheets of the index according to the page number printed in the right bottom corner of each page. Example: page no. 3-5 3 = chapter 3 5 = page 5 All pages with a page number that begins with the digit 3, for example, must be put under the index heading „Chapter 3″. -Index sheets that have not been marked with a certain chapter are for your personal convenience. T he respective headings can be entered in the list of contents. Remove page (s) Replace by page (s) Insert page (s) after page 2-1 / 2-7 2-1C 2-7C to 2-9C 3-1 3-1C 4-1 to 4-14 4-1C to 4-13C 5-1 / 5-3 5-1C / 5-3C 5-6 to 5-8 5-6C to 5-8C 5-12 to 5-26 5-12C to 5-27C 6-1 / 6-4 6-1C / 6-4C 6-7 to 6-16 6-7C to 6-17C 7-1 to 7-2 7-1C to 7-2C 7-7 to 7-11 7-7C to 7-11C 8-1 to 8-13 8-1C to 8-21C 9-1 9-1C 9-10 to 9-13 9-10C to 9-16C 10-1 10-1C 10-8C to 10-11C 11-1 11-1C 11-11C to 11-13C
Repair manual KTM 250-525 SX, MXC, EXC RACING Art.-No. 3206007 -E EXPLANATION – UPDATING Edition 01/2003 3.205.85-ERepair Manual 400/520 SX, MXC, EXC RACING Basic version Model year 2000 (Engine number with first digit “0″) 2/2000 3.210.01-EUpdating of Rep.Manual 3.205.85-E Model year 2001 (Engine number with first digit “1″) 1/2001 3.210.44-EUpdating of Rep.Manual 3.205.85-E Model year 2002 (Engine number with first digit “2″)

Incoming search terms:

2004 KTM 250 EXC-R exhaust system INSTALLATION

0

Filed Under (KTM) by admin on 07-02-2012

download
1. Remove the rear shock and the standard exhaust pipe. And attach the rear shock again. (Standard exhaust flange should remain the current position) 2. Lightly attach the front exhaust pipe to the engine. (See Photo. 2) 3. Insert the joint and tail pipe to lightly attached front exhaust pipe in step 2. Shake the whole for the better fitting. Then, attach the supplied springs to the joint. Lightly attach this tail pipe with the standard bolt. *Insert the two inner collars to the joint. 4. Lightly assemble the silencer and the silencer stay. Insert this to the tail pipe. Lightly attach this tail pipe to the standard attachment position with supplied bolt and collar. Check the best position for the silencer band. (See Photo. 3) 5. Remove the silencer attached in step 4. Securely fasten the bolt of the silencer band. Insert this silencer to the tail pipe and lightly fasten the bolt of the stay. 6. Securely attach the tail pie followed by the silencer stay. 7. Attach supplied springs to the joint of the silencer. 8. Clean all surfaces. Remove any oil on the exhaust pipe and silencer. 9. Make sure all bolts and nuts are securely fastened. Run the engine and ensure there are no exhaust gas leaks. (See Photo. 4) *Carburetor adjustment will be required in the weather and course

2007 KTM 250 SX-F 450 SX-F INSTALLATION MANUAL

0

Filed Under (KTM) by admin on 06-02-2012

download
Clutch lever The clutch lever [1] is located on the left side of the handlebar. The adjusting screw [A] is used to change the original position of the clutch lever (see maintenance work on chassis and engine). The clutch is hydraulically actuated and adjusts itself automatically. Hot start lever If you pull the red hot start lever [2] during the starting procedure backward, a bore in the carburetor will be opened through which the engine may take in additional air. The result is a “lean” fuel-air mixture of the type needed for hot starts. 2 1 A Fuel tap OFF In this position the fuel tap is closed. No fuel can flow to the carburetor. ON During operation the twist grip must be turned to ON. This means that the fuel can flow to the carburetor. OPERATION INSTRUMENTS »
Starter button (450 SX-F) Pushing the black starter button [3] will actuate the E-starter. ENGLISH 6 Hand brake lever The hand brake lever [1] is mounted on the handlebars on the right and actuates the front wheel brake. The adjusting screw [A] can be used to change the basic position of the hand brake lever (see “Maintenance”). Short circuit button The short circuit button [2] turns off the engine. When pressing this button, the ignition circuit is short-circuited. Filler cap To open the filler cap: Turn the filler cap 45 ° counter-clockwise. To close the filler cap: Put the filler cap on and turn it 45 ° clockwise. OFF ON 1 A 2 3 ENGLISH 7 OPERATION INSTRUMENTS » Choke If you pull the choke button [1] out as far as possible, a bore in the carburetor will be opened through which the engine may take in additional fuel. The result is a “fat” fuel-air mixture of the type needed for cold starts. To deactivate the choke, push the choke button back into its basic position. Shift lever The shift lever is mounted on the left side of the engine. The position of the gears is shown in the illustration. Neutral is located between first and second gear. Kickstarter (250 SX-F) The kickstarter is mounted on the right side of the engine. Its upper part can be swivelled. Foot brake pedal The foot brake pedal is located in front of the right footrest. Its basic position can be adjusted to your seat position (see maintenance work). Plug in stand The plug-in stand can be attached to the wheel spindle on the left side of the motorcycle

Incoming search terms:

Incoming search terms: