2004-2005 KTM 250/ 400/ 450/ 525 Side Panel Fuel Tank removal and Installation Instructions

0

Filed Under (KTM) by admin on 22-01-2012

download
1. Remove airbox cover. Drill stock rivet nut in frame tube through with a ¼” drill as shown in Photo 1. Drill completely through frame tube. We suggest you make a small guide hole in the top of the frame tube first so that you drill straight through the frame member and not come out the side of the frame tube. Photo 1 .Install Lower mounting bracket as shown in Photo 3 noting its orientation. Install the aluminum cone into the recess at the bottom of the stock airbox , then bolt the bracket on with the 6 x 70 mm bolt. Nylock nut threads to top of bolt on top of frame tube as shown in photo 2. Photo 3 2 3. Install the upper mounting bracket shown in Photo 4. Note that in either the MXC or the EXC installation four to six of the 6 x 18 mm fender washers should be installed between the bracket and the subframe. The counter-sunk hole should be positioned toward the rear wheel. Leave the bracket slightly loose until step 6. Photo 4 The best routing for the fuel line (Photo 5 & 6 ) requires drilling holes in the airbox. See Step 4 for hole locations. 4. Drill a 3/8″ hole at the front left corner of the airbox as shown in Photo 6. Make sure the location you choose will not result in the hole coming out behind the frame tube or into the rubber airbox boot. Be very careful drilling this hole.

Incoming search terms:

KTM SX-F 250/ 450 Front Fork Kit INSTALLATION MANUAL

0

Filed Under (KTM) by admin on 22-01-2012

download
Breather plug Make sure to aerate the front fork at regular intervals: Put the motorcycle on a workstand so that the front wheel barely touches the ground. Loosen the breather plug to release excessive pressure in the front fork. Recommended Service Intervals Every 25 hours. Make your service and maintenance according to Öhlins Workshop manual. Disposal Discarded Öhlins products should be handed over to an authorized Öhlins workshop or distributor for proper disposa Compression damping adjuster The compression adjuster is located at the top of the fork leg. Adjust by turning the slotted screw with a screwdriver. Rebound damping adjuster The rebound adjuster is located at the bottom of the fork leg. Adjust by turning the slotted screw with a screwdriver. To Reset The adjusters have a normal right hand thread. Turn the damping adjusters gently clockwise to fully closed (pos. zero [0]). To open, turn counter clockwise, and count the clicks until you reach the recommended number. For recommended clicks see Set-up data. Static sag can only be changed with softer or harder spring rate.

KTM 4357/ 4860 MX Multi Adjuster WP Suspension manual Disassembly And Assembling

0

Filed Under (KTM) by admin on 13-02-2011

download
Disassembly forkleg 12_062 12_079Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 5 Frontfork 4357/4860 MXMA 02/2002 Clamp the forkleg (axle-clamp) in the vice and let the outer-tube down. Pull the spring downwards… …and place open-end spanner (size 22) on the hydraulic stop. Unscrew the screw-cap. 12_067 12_068 12_069 12_072Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 6 Frontfork 4357/4860 MXMA 02/2002 Remove the screw-cap from the piston- rod. 12_070 Remove the preload spacers. 12_074 Pull the spring downwards and remove the spanner. 12_075Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 7 Frontfork 4357/4860 MXMA 02/2002 Remove the spring. 12_076 Remove the adjustment tube with the O-ring. 12_089
Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 8 Frontfork 4357/4860 MXMA 02/2002 Clamp the axle-clamp in the vice so that the forkleg is at an angle of ±45 degrees. 12_095 Unscrew the compression holder out of the axle-clamp. (size 19) (when the cartridge is rotating with the holder, bend the piston- rod a little bit to the side) 12_096 Drain the oil out the forkleg. 12_094 Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 9 Frontfork 4357/4860 MXMA 02/2002 Remove holder compression. Caution: oil iscoming out the cartridge. Disassemble the cartridge out the forkleg. 12_097 12_098 12_099 Disassemble the dust-wiper

Incoming search terms:

KTM Preload Adjuster frontfork Disassembly And assembling

0

Filed Under (KTM) by admin on 13-02-2011

download
Product Exploded View Disassembly & Assembling Workshop manual Preload Adjuster frontfork 5 Preload Adjuster Frontfork 03/2002 Screw the screw-cap to the right so that the spring washer is turning out of the screw-cap PA. Remove the spring washer. Pay attention to the assembling direction!!! Turn the plastic adjustment tube holder out of the screw-cap. 12_021 12_022 12_023Product Exploded View Disassembly & Assembling Workshop manual Preload Adjuster frontfork 6 Preload Adjuster Frontfork 03/2002 1. Remove the O-ring inside. Unscrew the air release plug. 12_024 12_025 12_026 2. Remove the O-ring.Product Exploded View Disassembly & Assembling Workshop manual Preload Adjuster frontfork 7 Preload Adjuster Frontfork 03/2002 Disassemble the adjusting knob from the screw-cap. Pay attention to the steel balls and spring!!! 12_027 12_028 12_029 Heat the steel nut. Unscrew the nut (size 32) clockwise .Product Exploded View Disassembly & Assembling Workshop manual Preload Adjuster frontfork 8 Preload Adjuster Frontfork 03/2002 The nut. Pay attention to the assembling direction!!! Remove the O-ring. 12_030 12_031 12_032 Push the holder rebound PA out of the screw-cap.Product Exploded View Disassembly & Assembling Workshop manual Preload Adjuster frontfork 9 Preload Adjuster Frontfork 03/2002 – springring – spring washer – O-rings – holder rebound adjustment tube – rebound adjusting knob with steel balls and spring – air release screw with O-ring – nut – holder rebound adjustment cpl. with O-ring – screw-cap PA

Incoming search terms:

KTM WP FORK 4860 MXMA CLOSED CARTRIDGE REPAIR MANUAL

0

Filed Under (KTM) by admin on 13-02-2011

download
Adjustments -Take notice of the position of the compression adjustment 1 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -Remove the rubber cap out of the axleclamp. -Take notice of the position of the rebound adjustment 2 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -For the standard position see setting list. Position of the compression and rebound adjustment -Set the rebound position 1 , see KTM-Owners manual. -Assemble the rubber cap. -Set the compression position 2 , see KTM-Owners manual. 1 22-22 Repair manual WP Fork “Closed Cartridge” Art.No.: 3.211.199-E Explanation of the spring preload -Total spring length without the spacers, see chapter inspection of the spring! -Spring length with spacers 1 , see setting list. -Spring with the spacers. 1 . -The spring is assembled in the front fork leg. NOTE: the distance of “B” is less then the length of “A”. A – B = Spring preload A 1 1 B2-23 Air release screw -Place the motorcycle on the stand. NOTE: the front wheel must be lift of the floor! -Unscrew the air release screw 1 of the screw cap on top of the front fork and tighten after approx. 10 seconds the air release screw. Recommended periodic maintenance and inspection of the 4860 SX/SXS/SMR front fork 1 A 100 liter fuel consumption is equivalent to approx. 15 operating hours Clean dust scrapers (after 1 hour) Bleed fork legs regularly – after every cleaning Check the inner tubes on scratches / leakage Visual check of damaging of the outer-tubes / replace if necessary Complete service without disass. the closed cartridge of the fork Complete service including the closed cartridge of the front fork

Incoming search terms:

2005-2007 KTM 5018 DCC 5018 SXS 5018 SMR WP SHOCK ABSORBER REPAIR MANUAL

0

Filed Under (KTM) by admin on 13-02-2011

download
liter fuel consumption is equivalent to approx. 15 operating hours Check the bearing in the shock absorber top / replace if necessary Check the piston rod on scratches / leakage Check the static sag – before riding Check the spring Check the bump rubber Check the O-ring of the spring retainer / replace if necessary Complete maintenance of the shock absorber 10 hours 65 liter 20 hours 130 liter 30 hours 200 liter 40 hours 260 liter 50 hours 325 liter 60 hours 400 liter 70 hours 455 liter 80 hours 520 liter 90 hours 600 liter 100 hours 665 liter Adjusting the position of the compression and rebound damping Rebound damping: -Turn in the adjusting screw 1 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Compression damping, low speed: -Turn in the adjusting screw 2 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Compression damping, high speed: -Turn in the adjusting screw 3 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Adjusting the spring preload NOTE: the spring preload is the difference between the unloaded and preloaded length of the spring. -Tighten the adjusting nut 4 with the special tool T106 until you have the prescribed spring preload. -Tighten the lock screw on the adjusting nut. Recommended periodic maintenance and inspection of the 5018 SXS/SMR Shock absorber

Incoming search terms:

KTM 125 EXC, EXC SIXDAYS 200 XC, XC-W, EXC 250 XC, XC-W, EXC, EXCSIXDAYS 300 XC, XC-W, EXC-E, EXC-ESIXDAYS OWNER'S MANUAL 2008

0

Filed Under (KTM) by admin on 02-12-2010

download
Chassis number The chassis number is stamped on the right side of the steering head tube. Enter this number in the field on page no 1. Engine number, engine type The engine number and the engine type are stamped into the left side of the engine below the engine sprocket. Enter this number on page 1. Clutch lever The clutch lever [1] is located on the left side of the handlebars. The adjusting screw [A] is used to change the original position of the clutch lever (see maintenance work on chassis and engine). The clutch is hydraulically actuated and adjusts itself automatically. Hand brake lever The hand brake lever [2] is mounted on the handlebars on the right and actuates the front wheel brake. The adjusting screw [B] can be used to change the basic position of the hand brake lever (see maintenance work on chassis and engine). OPERATION INSTRUMENTS » 1 2 A B
ENGLISH 6 OPERATION INSTRUMENTS » TEST All of the display segments briefly light up for the display function test. WS (wheel size) The display changes and the circumference of the front wheel is briefly displayed in millimeters (2205 mm corresponds to a front wheel circumference of 21″ with production tires). Afterwards the display will return to the previous display mode. Electronic speedometer The display in the electronic speedometer is activated as soon as you press a button on the speedometer or an impulse is received from the wheel sensor. The display lights up when the engine is running. The display is cleared if no button is pressed for 1 minute or no impulse is received from the wheel sensor. The button is used to change between display modes. The + and – buttons are used to control various functions. SPEED display mode / H (service hours) Only the SPEED / H and SPEED / ODO display modes are activated in the condition at delivery. SPEED/H is displayed whenever the display is activated and the front wheel is not turning. It automatically changes to the SPEED/ODO display mode as soon as the front wheel starts turning. SPEED displays the speed. H displays the engine’s service hours. The service hour counter starts to count as soon as you start the engine. The displayed figure cannot be changed. Service intervals are indicated in service hours for some KTM offroad motorcycles, making the service hour counter a very practical function. SPEED / ODO display mode (odometer) The SPEED/ODO mode displays the speed and the total distance traveled. The display automatically changes to the SPEED/H display mode when the front wheel stops turning. + button no function – button no function briefly press buttonchanges to the next display mode hold button 3 secs. changes to the next display mode The electronic speedometer has a number of display modes (functions) that you can also activate (reveal) (see: Activating and deactivating display modes).
ENGLISH 7 OPERATION INSTRUMENTS » SPEED / LAP (lap time) display mode You can use the manual stop watch to stop and store up to 10 lap times, which you can view in the LAP/LAP display mode (see below). LAP displays the lap times in hours, minutes and seconds. + button Starts and stops the stop watch, lap time is not reset to 0 – button Stops the stop watch, stores the lap time and restarts the stop watch again. The time is reset to 0. A total of 10 lap times can be stored. If the lap time continues to run after you press the – button, all 10 memory locations are occupied.To clear all of the stored lap times, hold the button for 3 seconds in the SPEED/LAP mode.Up to 10 lap times can be stored in this way. briefly press buttonChanges to the next display mode.If no lap time is stored or the motorcycle is driving, the LAP/LAP mode will be skipped. hold button 3 secs. Clears all LAP figures SPEED / CLK (time) display mode CLK displays the time in hours, minutes and seconds. + button no function – button no function briefly press buttonchanges to the next display mode hold button 3 secs. set the clock menu To set the clock, see „Setting the clock”. Activating and deactivating display modes In the display mode SPEED/H, press and hold the button for 3 seconds to access the SETUP menu. The active functions will be displayed. The blinking function can be activated by pressing the + button and deactivated by pressing the – button. Press and hold the button 3 seconds to store the settings. If no button is pressed for 20 seconds, the setting will be stored automatically and the display will return to the SPEED/H mode. + button activates the blinking display – button deactivates the blinking display briefly press buttonchanges to the next display without changing any settings hold button 3 secs. starts the SETUP stores the settings and changes to the SPEED/H mode

Incoming search terms:

KTM 250 EXC RACING 450 SX, MXC, EXC RACING 525 SX, MXC, EXC RACING OWNER`S MANUAL

0

Filed Under (KTM) by admin on 28-11-2010

download
Digital speedometer, indicator lamps The green control lamp 1 flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp 2 lights up when the high beam is on. Electronic speedometer The electronic speedometer display is activated as soon as the engine is switched on and the motorcycle starts to move. The engine must be started in order for the speedometer to be supplied with electricity from the generator. An impulse must be received from the wheel sensor to activate the display; the front wheel must turn at least one time. TEST All of the display elements will light up for 1 second for the function test. WS (wheel size) The display will change and briefly show the diameter of the front wheel in millimeters. If the front wheel does not turn, the display will automatically change to the SPEED/H mode. If the front wheel turns, the display will automatically change to the SPEED /ODO mode. SPEED/H (hours) display mode When you stop driving and no impulses are sent from the wheel sensor, the display mode will automatically change from SPEED/ODO to SPEED/H. H shows the operating hours. The operating hour counter starts to count as soon as you start the engine. The displayed figure cannot be cleared. Service intervals are indicated in operating hours for some KTM offroad motorcycles, making the operating hour counter a very practical function. SPEED/ODO display mode The SPEED/ODO mode shows the speed and the total kilometers traveled. When the front wheel stops turning, the display will automatically change to the SPEED/H mode. The information will disappear in the display when the front wheel stops turning for 1 minute. NOTE: A Tripmaster switch (part no 583.14.069.244) is available as an accessory and enhances the electronic speedometer by providing the following functions: 2x Tripmaster 2x chronometer for the lap time Average speed Maximum speed Clock Display in miles

Incoming search terms:

KTM 125/ 200/ 250/ 300 SX, MXC, EXC SERVICE MANUAL

0

Filed Under (KTM) by admin on 28-11-2010

download
Compression damping of shock absorber (MXC, EXC) The compression damping (during compression) can be adjusted for the MXC and EXC shock absorbers (Mono Compression Control). The degree of damping can be adjusted by turning adjusting screw 1 with a screwdriver. Turning in a clockwise direction will increase the damping, turning in a counterclockwise direction will decrease the damping. STANDARD ADJUSTMENT: -Turn the adjusting screw clockwise to the stop. -Then turn the adjusting screw counterclockwise, counting the number of clicks that corresponds to the respective type of shock absorber. Type White Power 1218X757…………..17 clicks Type White Power 1218X759…………..17 clicks * WARNING * THE DAMPING UNIT OF THE SHOCK ABSORBER IS FILLED WITH HIGH – COMPRESSION NITROGEN . NEVER TRY TO TAKE THE SHOCK ABSORBER APART OR TO DO ANY MAINTEN – ANCE WORK YOURSELF . SEVERE INJURIES COULD BE THE RESULT . NEVER UNSCREW THE BLACK SCREW 2 CONNECTION (24 MM ). Rebound damping of shock absorber (SX, MXC, EXC) By using the adjusting screw 3 , the degree of damping of the rebound can be adjusted. Turn the knob to the right side to increase damping, turn it to the left side to reduce damping during rebounding. STANDARD ADJUSTMENT: -Turn the adjusting screw clockwise to the stop. -Then turn the adjusting screw counterclockwise, counting the number of clicks that corresponds to the respective type of shock absorber. Type White Power 1218X756…………..28 clicks Type White Power 1218X757…………..28 clicks Type White Power 1218X759…………..26 clicks * WARNING * THE DAMPING UNIT OF THE SHOCK ABSORBER IS FILLED WITH HIGH – COMPRESSION NITROGEN . N EVERTRYTOTAKETHESHOCKABSORBERAPARTORTODOANYMAINTE – NANCE WORK YOURSELF . SEVERE INJURIES COULD BE THE RESULT . NEVER UNSCREW THE BLACK SCREW 4 CONNECTION (15 MM )

Incoming search terms:

KTM 125 SX, EXC 200 EXC, XC, XC-W 250 SX, EXC, XC, XC-W 300 EXC, XC, XC-W OWNER'S MANUAL

0

Filed Under (KTM) by admin on 27-11-2010

download
Short circuit button (SX) The short circuit button [1] turns off the engine. When pressing this button, the ignition circuit is short-circuited. Combination switch (EXC) The light switch has 2, respectively 3 switch positions. [A] = Light off (this function is not available in all models) [B] = Low beam on [C] = High beam on You may use button [2] to actuate the horn. The red short circuit button [3] serves to switch off the engine. Leave the switch pressed until the engine stops. Headlamp switch (XC-W) In this model the headlamp is switched on with the pull switch [4] . Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right Emergency OFF switch (Australia) The emergency OFF switch [5] is located next to the throttle grip. Primarily designed as safety or emergency OFF switch, it should normally not be in its activated state. In this position, the ignition circuit is shorted; if the engine is running, it will stall immediately, if it is at standstill, it will not start. In this position, the ignition circuit is enabled; the engine should start. 1 2 3 5 A B C 4
ENGLISH 12 Filler cap To open it: turn filler cap counter-clockwise. To close it: put filler cap back on and tighten it by turning it clockwise. Install tank breather hose [1] without kinks. Filler cap (XC, XC-W) To open the filler cap: Turn the filler cap 45 ° counter-clockwise. To close the filler cap: Put the filler cap on and turn it 45 ° clockwise. Fuel tap OFF In this position the fuel tap is closed. No fuel can flow to the carbure- tor. ON During operation the twist grip must be turned to ON. This means that the fuel can flow to the carburetor. With the twist grip in this position the tank will be emptied until only the reserve is left. RES The reserve tank cannot be tapped until the rotating handle is turned to the RES position. Fill the tank as soon as possible and remember to turn the rotating handle back to the ON position so that you will have backup fuel next time, too. Reserve of the 8.5 l tank . . . . . . 1.3 l (0.32 USgallons) Reserve of the 10 l tank . . . . . .1.7 l (0.45 USgallons

Incoming search terms:

Incoming search terms: