TRAILER ELECTRICAL ISOLATOR Installation Procedures

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Control circuit connections to the motorcycle (normally under the seat or trunk): #1 Brownwireshould be connected to the taillight circuit. #2 Green/Redshouldbe connected to the brake light circuit. #3 LightBlueshould be connected to the left turn signal circuit. #4 Orangeshouldbe connected to the right turn signal circuit. #5 Greenwireshould be connected to frame ground (not to the battery negative post) #6 Yellowwire should be connected to positive 12 volt battery supply. TRAILER ELECTRICAL ISOLATOR WARRANTY -Krissproductsare covered under our standard limited warranty Items returned for inspection must have prior return authorization from the factory. All items must be sent freight prepaid. We are not responsible for any item returned without authorization. Technical assistance is available on the Internet. All items returned for inspection and found to operate properly will be subject to a minimum testing fee. Complete details of our limited warranty maybe found on our internetpages. for defective materials and workmanship. NOTE: Please observe standard good installation procedures by not placing or attaching electrical devices next to plastic decorative outer panels or fairings to prevent damage due to heat. Electricity can produce high temperatures in the event of short circuits. KRISS INDUSTRIESINC. wwwkriss.com . Techinical Support Warranty Assistance Product Information Contact Information KRISS MOTORCYCLE PRODUCTS Installation Procedures Use a test light to identify the correct circuits. If you do not have the proper tools or knowledge to identify the proper wiring we suggest that you seek professional assistance locally. Please note that we are notable to provide telephone or email installation and/or electrical training

MC 1200 Motorcycle Trailer – 1200 lbs Assembly Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Tongue: Remove tongue assembly from the frame bundle. Insert into the tongue channel and slide into the front cross member of the frame. Secure with two (2) 3/8″ X 4″ carriage bolts and 3/8″ flange lock nuts. Tighten. Thread the tongue wire harness through the front top hole in the tongue and pull out the hole provided in the left side of the tongue towards the rear. Connect to the frame harness with the plugs provided. Install grommets. Safety Chains: Insert a 3/8″ X 1-1/4″ hex bolt into a 3/8″ flat washer, safety chain and then through the lower hole on the front of the tongue. Place on a 3/8″ flat washer on the inside of the tongue and secure with 3/8″ flange lock nuts. Repeat procedure on the opposite side of the tongue. Tighten. Coupler: Mount the coupler onto the tongue with a 1/2″ X 4″ hex bolt trough the rear mounting holes of the coupler. Using two (2) 1/2″ X 1″ hex bolt attach the coupler to the tongue using the front mounting holes. Secure with flange lock nuts. Tighten. Axle: Attach the spring busing in the rear spring shackles with 1/2″ X 3- 1/4″ hex bolts and 1/2″ flange lock nuts. Position the axle under the trailer with spring eye to the front of the trailer. Slip the flat end of the spring in the rear spring shackle above the bushing just installed. Secure the front spring eye to the front spring shackle with 98/16″ X 3-1/4″ hex bolts and 9/16″ hex lock nuts. Tighten. Mount the tire and rim assemblies to the axle assembly with 1/2″ lug nuts and tighten to 80-90 ft./lbs. of torque using the rotation pattern as shown in the Shore Land’r Owners Manual . Retorque the lug nuts after 50 miles of driving and then periodically thereafter. Ramps: Locate the loading ramp. Note that one end has two holes punched in the bottom of the channel. (See parts drawing) Insert a 3/8″ X 1-1/2″ full threaded carriage bolt into one of these holes. Secure in this position using a 3/8″ flange lock nut. Tighten Place a second 3/8″ flange lock nut onto the same bolt only until the threads of the bolt are exposed through the nut locking it in

Incoming search terms:

Motorcycle Trailer STANDARD FEATURES

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
6′ Standard Interior Height 06 Aluminum Black & Silver (or Silver) Wheels 15″ Radial Tires 28″ V Nose 16″ Center Cross Members 16″ Center Roof Bows 16″ Center Wall Posts White Vinyl Ceiling 5.2mm White Vinyl Wall Liner (4) Heavy Duty D-Rings on 6′ Wides (8) Heavy Duty D-Rings on 7′ Wides 3/4″ Plywood Floor Motorcycle Transition Flap (1) Removable Chrome Wheel Chock – 6′ Wides (2) Removable Chrome Wheel Chocks – 7′ Wides LED Clearance and Tail Lights (2) 12 Volt Dome Lights 12 Volt Wall Switch Bright Aluminum 16″ Tall Down Both Side Walls Two Tone Exterior (No Bright Strip Between Colors) Bright Aluminum on Front V Nose Bright Aluminum Front Corners ATP Fenders .030 Smooth Aluminum (Glued Exterior) Aluminum Seamless Roof Light Duty Ramp Door Blank RV Style Door – 32″ x 64″ (6′ Wides) Blank RV Style Door – 36″ x 64″ (7′ Wides) Fold Down Jacks Spring Axles or Torsion Axles TSR Vents Brakes on 7′ Wide Models 24″ ATP Stone Guard 5 Year Limited Warranty

Power Grid LED Integrated Tail Light General Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Running Light, Brake Light and Blinker Function The triple wire harness plugs directly into the OEM wire harness designed for the stock tail light. Optional integrated turn signals are designated by Yellow and Blue wires coming off of the harness connected to the DMP LED Integrated Tail Light. If you are sitting on the bike the yellow wire connects to the right side blinker and the blue wire connects to the left side blinker. Installation DMP LED Integrated Tail Lights are designed to replace the OEM factory unit with the use of OEM original hardware. Pay close attention during the disassembly process to ensure proper assembly later. Tip: During disassembly it might be useful to use a small digital camera or camera phone to remind the installer where things go in conjunction with the OEM factory service manual. Test Function NOTE: Double check before you test the functionality of your new DMP tail light, make sure there are no crossed or short circuited connections before you reconnect the battery. If your new DMP tail light is not operating properly please check all your connections thoroughly

SR-C400 Motorcycle Security System INSTALLATION MANUAL AND USER'S GUIDE

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Routing the Antenna Wire The MCM includes an 18″ antenna wire. The first 12″ is a coaxial wire; the remaining 6″ is the reception antenna wire. When routing, try to avoid running the antenna along or near metal. For best performance, have the antenna wire as vertical as possible and exposed. Wire Connections The system includes one harness (HAR-1a) that connects directly into the MCM. The harness is split into three plugs: one for the GEN-1a connector, one for the optional SN-5 connector and one for the data output for future expansion. Note: Each plug is unique and will only fit the appropriate component one way. Main Harness Note: If the optional factory connector kit is being used, please disregard this section of the instructions and refer to the instructions supplied with the factory connector kit. The main harness consists of two harnesses. One is labeled (HAR-1a) and the second is labeled (GEN-1a). Plug in the white 4 pin connector from the (HAR-1a) into the matching 4 pin connector from the (GEN-1a). The (HAR-1a) also has a waterproof connector that plugs into the MCM. The wires should be connected as follows: HAR-1a Black wire with fuse and ring terminal – To battery Positive (+). GEN-1a Black wire – To ground (-). Orange wire – To tail light wire or any other wire that is hot (+) when ignition is ON (NOTE: this is an input to the alarm this connection is not designed to flash the tail light). Color Codes: Ground (-) Tail Light Honda Green wire Brown wire Kawasaki Black wire Red wire Suzuki Black/White Brown wire Yamaha Black wire Blue wire Harley Davidson Black wire Blue wire

Incoming search terms:

Street Magic Magical Wizards LED Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Always wear appropriate safety gear including safety glasses when soldering or performing any electrical work. It is highly recommended that safety glasses be worn throughout this installation process. Temperature of bike must be at least 60 degrees F. for tape to properly cure. Read all directions before starting project. 2. Turn fuel supply valve to off position before starting. Be sure bike is on level surface and secure and cool. 3. Important: Disconnect negative battery cable from battery; refer to owner’s manual. Failure do to so may result in electrical shock, injury, or fire. Secure negative battery cable away from positive side of battery and all other positive voltage sources on bike. 4. Select hidden locations to mount LED Accent Lights to provide best coverage. 5. Remove fuse from fuse holder. 6. Clean mounting locations on both motorcycle and accent lights with 3M promoter, promoter sponge will dry up quickly, place sponge in sealed plastic bag when not in use. Do not touch 3M promoter with bare fingers. 7. Place piece of double sided tape on accent light if needed, lights come pre-taped on back surface. Trim excess off sides with razor blade. Carefully remove backing from double sided tape and place light on selected mounting location. Press firmly and hold for 10 seconds. Repeat for all lights to be mounted on bike. 8. Route wires from accent lights back to central points near battery compartment under seat. Route wires such that they not interfere with normal operation of bike. Cut off any excess wires, strip back insulation as required. 9. Select several locations to secure wires to frame. Secure wires using tie wraps provided. 10. Join all black wires from LEDs into one Cage Clamp Connector #1. Join all Red wires from LEDs into Cage Clamp Con- nector #2, Join all Blue wires from LEDs into Cage Clamp Connector #3, Join all Green wires from LEDs into Cage Clamp Connector #4. 11. Connect Orange wire from the remote control wire harness to the Red Cage Clamp Connector, connect Blue wire from remote control wire harness to Blue Cage Clamp Connector, connect Green wire from remote control wire harness to Green Cage Clamp Connector. Connect White wire from remote control wire harness to Black Cage Clamp Connector. 12. Crimp spade connector on ends of remaining Red and Black wires from Remote Wiring Harness. Heat spade connector with heat gun so that it shrinks around wire. 13. Connect Red Wire to Positive (+) side of battery, and Black Wire to (-) Side of battery. Take necessary precautions when making connection and refer to bike’s owner’s manual. DO NOT allow any tools to touch both positive (+) side of battery and any metal surface on bike as it will cause a short which could result in serious injury and damage to the battery or other electrical circuits.

DRAG SPECIALTIES MINI SPEEDOMETER WITH LED INDICATOR LIGHTS INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Place the motorcycle on a level and secure area. Disconnect the battery. 2. Refer to the appropriate factory service manual and remove the OEM speedometer and indicator lights. The indicator lights usually unplug either in the rear of the headlight or under the gas tank area. 3. Mount the new speedometer in the desired location. 4. Locate the OEM wire for the high beam indicator light. Connect it with the blue wire from the wire harness on the speedometer. Connect the blue/black wire from the speedometer to ground. 5. Locate the OEM wire for the gauge illumination (back) lighting. Connect this wire to the orange wire on the speedometer. Connect the black wire on the speedometer to ground. 6. Locate the OEM wires for the turn signals. Usually they are brown and violet wires. NOTE: You will notice only one bulb for the turn signals in the gauge and two wires from the bike to the harness. If you connect both of these wires directly to the yellow wire on the speedometer, this will allow feedback and cause all the signals to flash at once. To prevent this, you will need to add a diode between each OEM turn signal wire and the yellow wire coming from the speedometer. We recommend that you utilize a Dyna tach adapter, Part #D-101, available separately. This tach adapter includes the diodes necessary to allow the turn signal indicator light to operate correctly. Follow the instructions for the tach adapter, substituting the wires from the original wire harness found in step 6 for the two ignition terminals shown in the wire schematic. Hook the white wire on the tach adapter to the yellow wire for the turn signal indicator on the speedometer. If you use the D-101 adapter, skip steps 7-9 and go directly to step 10. 7. Take one of the diodes, making sure to observe the correct polarity, and attach it to the brown turn signal wire on the bike. 8. Take the remaining diode, again making sure to observe the correct polarity, and attach it to the violet turn signal wire on the bike

Incoming search terms:

Baron Tachometer Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Some models like Harley-Davidson, Kawasaki Vulcan FI models, Suzuki FI models, Honda VTX 1800 and others may require the included Tach Adapter. See separate instructions for installation of the adaptor. Wiring instructions for 7-Color LED Tachs Wire Baron’s Tach to one of your motorcycle’s ignition coils via the following schematic: • Green wire of tach to NEGATIVE terminal of coil (see FAQ to determine your bike’s negative side) • Black wire of tach to CHASSIS (Ground) • Red wire to of tach to POSITIVE terminal of coil (or other switched 12 volt source) • Red wire from control box to POSITIVE terminal of coil (or other switched 12 volt source) • Black wire from control box to CHASSIS (ground) • Control box plugs into tach with the 4-way connector • Button plugs into the control box. Button can be mounted on handlebar or any other convenient place Wiring instructions for White- or Black-Face Tachs Wire Baron’s Tach to one of your motorcycle’s ignition coils via the following schematic: • Green wire to NEGATIVE terminal of coil (see FAQ to determine your bike’s negative side) • Black wire to CHASSIS (Ground) • Red wire to POSITIVE terminal of coil (or other switched 12 volt source) • Blue wire to POSITIVE terminal of coil (or other switched 12 volt source) General mounting instructions (1) Mount new Baron Tach on handlebar in your preferred position. Ideal location is between handlebar risers. If mounted off- center, you can rotate tach face back to vertical (or any position you desire) by first loosening tach unit’s set screw (found either in handlebar area of housing or underside of housing, depending on tach style), then unscrewing tach housing’s bezel, rotating tach, re-installing bezel and retightening set screw. Secure handlebar clamp by first tightening the rear, flat side of clamp all the way down, then tighten tapered front side of clamp until tach does not rotate. There should be a small gap on the pointed side and no gap on the flat side when the clamp is correctly tightened. (2) Route tach’s wire harness lead to coil as necessary for simplest and cleanest installation. Feed tach harness alongside bike’s wiring harness (passing behind any plastic frame covers), then downward toward coil. (3) Make your wire connections as recommended above. Use the spade and piggyback connectors

Incoming search terms:

CRUISADER Motorcycle Laser-Radar Detector Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Installation of Laser-Radar Antenna 7 General Information The laser-radar antenna is water resistant and designed to be mounted on a motorcycle, snowmobile, etc. Radar signals will pass through non-metallic materials such as fiberglass and plastic, however, be sure not to mount the receiver behind any metal, as it will block the receiver’s antenna. This receiver also incorporates a laser detector. In order for the laser receiver to “see”, it can not be mounted behind any object. In some installations, this is not possible. We supplied an additional laser only receiver for this instance. If the installation allows for a clear view for laser-radar receiver, the extra laser receiver can be used for rear detection. Because the optimallocation for mounting the antenna varies by vehicle type, the hardware supplied is designed to offer a wide variety of mountingoptions. Note: The “antenna” is the bubble area on the case. All references to antenna in this manual will be thebubble area. Note: Use of hardware that is not supplied or DRILLING into the case will cause damage to the receiver and void the warranty. Antenna Mounting Brackets There are 3 ways in which to mount the laser-radar antenna; dual lock fastener, reflector bracket and universal brackets (similar to old car radio ground straps). These mounting accessories can be used on their own or in combination to provide the best mounting solution for the vehicle. Do not drill into the receiver housing! The reflector bracket serves two purposes; (1) to allow vertical mounting of the antenna (see page 10 for vertical install instructions) and (2); when mounted in reverse (angled portion towards the wires.) allow the receiver to be installed on any horizontal area.

LED Motorcycle Power Box Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
This box requires the presence of a mounting plate secured to the motorcycle’s luggage rack. If the bike in question is not equipped with a mounting plate, one must be fabricated prior to installation of this box. Five mounting holes (.281″ dia.) are required to mount this box. If the motorcycle is already equipped with a mounting plate, it may be necessary to drill the 5 mounting holes required for this installation. Use the diagram shown to determine the precise location of these holes. 1. Position the box onto the mounting plate. Align the 5 vibration dampeners with the 5 mounting holes in the mounting plate. 2. Using the illustrations shown, secure the box to the mounting plate using the provided hardware. Note: Your luggage rack may already have the correct mounting holes drilled. Check the measurements below and if these holes already exist at the proper distance, remove any existing mounting hardware from the holes and secure the box with the supplied mounting hardware. 3. Place the box into its mounting position on the deck and secure it with the supplied mounting hardware as shown in the diagram. Wiring: Diagrams for optional equipment are found below. Refer to the diagram on the following page for general motorcycle box wiring information

Incoming search terms: