2006 Saturn ION Window Regulator Replacement – Front Door

0

Filed Under (Uncategorized) by admin on 30-10-2011

download
regulator. Refer to Water Deflector Replacement – Front Door (See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ComponentsWater Deflector Replacement – Front Door) . Disengage the door glass to the regulator sash channel clips (2). Separate the door glass from the sash channel (1). 6. Push the window to the up position and tape in place. 7. Loosen the power window regulator bolts. Remove the rear regulator bolt. 8. Lift the window regulator, disengaging the loosened bolts from the door. 9. Disconnect the regulator electrical connector. 10. Remove the power window regulator from the door. Installation Procedure

Incoming search terms:

STEERING GEAR/ STEERING WHEEL REMOVAL AND INSTALLATION

0

Filed Under (Uncategorized) by admin on 05-10-2011

download
TEERING GEAR/STEERING WHEEL REMOVAL & INSTALLATION Page 3 of 4 STEERING GEAR/STEERING WHEEL INSTALLATION PROCEDURES (Cont’d) 2. Center spiral cable. a. Turn the cable counterclockwise by hand until it becomes harder to turn. b. Then rotate the cable clockwise about 2.5 or 3 turns to align the marks. (See Fig. 4) 3. Install the steering wheel. a. Align the matchmarks on the wheel and steering main shaft. b. Temporarily tighten the wheel set nut. c. Connect the spiral cable connector. 4. Bleed Power Steering System (when applicable). 5. Check steering wheel center point. 6. Torque steering wheel set nut. See the applicable vehicle’s repair manual for the torque specification. 7. Install and center steering wheel pad. NOTICE: Make sure the pad is centered and installed to the specified torque. If the pad has been dropped, or there are cracks, dents or other defects in the case or connector, replace the wheel pad with a new one. When installing the pad, take care that the wiring does not interfere with other parts and is not pinched between other parts. a) Connect the airbag wiring connector. b) Install the pad after confirming that torx screws are in the screw case. c) Using a torx socket, torque the screws to the specification in the vehicle’s Repair Manual. (See Fig. 5) d) Install the steering wheel lower cover

Incoming search terms:

2007 Toyota Tundra, 2WD & 4WD InstallatIon GuIde

0

Filed Under (Uncategorized) by admin on 28-09-2011

COMPRESSED AIR CAN CAUSE INJURY AND DAMAGE TO THE VEHICLE AND PARTS IF IT IS NOT HANDLED PROPERLY. FOR YOUR SAFETY, DO NOT TRY TO INFLATE THE AIR SPRINGS UNTIL THEY HAVE BEEN PROPERLY SECURED TO THE VEHICLE. 1. Jack up the rear of the vehicle using a jack or a hoist. Support the rear axle with jack stands and remove the rear wheels (fig. 2). Installing the loadlifter 5000 system TOOLS LIST Description .Qty Hoist or floor jacks . 1 Safety stands 2 Safety glasses 1 Torque wrench 1 5/16″ open-end or box wrench1 7/16″ open-end or box wrench.1 9/16″ open-end or box wrench1 Crescent wrench 1 Description  . . . . . . Qty Ratchet with 9/16″, metric, & 1/2″ deep well sockets  1 5/16″ drill bit (very sharp) 2 Heavy duty drill1 Hose cutter, razor blade, or sharp knife 1 Air compressor or compressed air source  1 Spray bottle with dish soap/water solution  1 DANGER 2. Bend the emergency brake cable bracket forward slightly on both sides of the vehicle (fig. 3). 3. It will be necessary to trim the stock jounce bumper to gain clearance for the air spring assembly’s lower bracket. Measure up from the base ¾” and mark a line on the jounce bumper. Using a box cutter or equivalent, cut the top of the jounce bumper off (fig. 3). USE ExTREME CAUTION WHEN CUTTING OFF THE JOUNCE BUMPER WITH THE CUTTING TOOL. CAUTION

TOYOTA FJ CRUISER 2007 TRD ALLOY WHEEL

0

Filed Under (Uncategorized) by admin on 21-09-2011

download
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation.
These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:-
• Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.).
• Safety (eye protection, rechecking torque procedure, etc.).
• Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).
• Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.

Cadillac Catera 1997 Steering Column Replacement

0

Filed Under (Uncategorized) by admin on 26-05-2011

Download

NOTICE: The front wheels of the vehicle must be maintained in the straight ahead position and the steering column must be in the LOCK position before disconnecting the steering column or intermediate shaft. Failure to follow these procedures will cause improper alignment of some components during installation and result in damage to the SIR coil assembly. NOTICE: Once the steering column is removed from the vehicle, the column is extremely susceptible to damage. Dropping the column assembly on its end could collapse the steering shaft or loosen the plastic injections that maintain column rigidity. Leaning on the column assembly could cause the jacket to bend or deform. Any of the above damage could impair the columns collapsible design. If it is necessary to remove the steering wheel. Under no condition should the end of the shaft be hammered on, as hammering could loosen the plastic injections which maintain column rigidity. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Disable Supplemental Inflatable Restraint (SIR) system. Remove the steering wheel. Remove the SIR coil. Remove the ignition lock cylinder. Disconnect the theft deterrent immobilizer connector. Remove the immobilizer. Remove the ignition switch. Remove the windshield washer switch.

Incoming search terms:

TOYOTA SUPRA 1990 REPAIR MANUAL COOLING SYSTEM LUBRICATION SYSTEM

0

Filed Under (Uncategorized) by admin on 22-05-2011

This manual contains maintenance and repair procedures for the 1990 TOYOTA SUPRA.
Applicable model: MA7O series 4 The manual is divided into 24 sections and 4 appendixes with
a thumb index for each section at the edge of the pages. Please note that the publications below have also been prepared as relevant service manuals to the components and systems in this vehicle.
Manual Name I Pub. No. ‘ 1990 Toyota Supra Electrical Wiring EWDO72U
Diagram Manual ‘ Toyota Supra Collision Damaged Body BRMOOSE Repair Manual ° Toyota Supra Collision Damaged Body BRMOOQE Repair Manual Supplement ° 1990 Model New Car Features NCFO59U
All information in this manual is based on the latest product in- formation at the time of publication. However, specifications and procedures are subject to change without notice.

Incoming search terms:

HARLEY DAVIDSON REAR SADDLEBAG GUARDRAILS INSTALLATION MANUAL

0

Filed Under (Harley Davidson, Uncategorized) by admin on 18-04-2011

download
Installation KITNUMBER 49087-01 1. Remove and save fasteners that retain saddlebag guardrails. 2. Replace stock saddlebag guardrails with new guardrails from kit. 3. Screw in and torque each stock fastener as follows: a. Four stock screws, Part No. 3678, using two new locknuts (1), Part No. 7667. Torque each screw to 19 ft-lbs. b. Two stock screws, Part No. 3601 using two new locknuts (2), Part No.7686. Torque each screw to 9 ft-lbs. For Domestic FLHRC/I Vehicles Only. (Does not apply to Harley Davidson International (HDI) vehicles): Federal Motor Vehicle Safety Standard (FMVSS) 108 requires all motorcycles to be equipped with side reflectors. Install, or have Dealer install, the reflectors, Part Nos. 59370-98 and 59371-98, which are purchased separately. Loss of visibility to other motorists could result in death or serious injury. 1. See Service Parts illustration. Position reflector so it is centered on the vertical portion of the saddlebag guard 1″ above the top end of the lower bend where the radius turns upward. Measure and use a small piece of tape to mark location for attachment of the lower edge of the reflector at the 1″ mark. 2. Remove protective tape backing from one reflector. Locate reflector above the 1″ mark. Apply reflector, using even pressure by rubbing back and forth on reflector. Repeat for other side. Note Reflectors are specific for each side. Reflectors have a flat end and a curved end. The curved end goes down. Top edge should be horizontal when positioned on guard. If not, reflector is for opposite side. KITNUMBER 49088-01 1. Remove and save fasteners that retain saddlebag guardrails. 2. Replace stock saddlebag guardrails with new guardrails from kit. 3. Using four hexsocket button head screws (4) removed earlier, attach saddlebag guards using the remaining two existing holes in each guardrail. 4. Screw in and torque each stock fastener as follows: a. Four stock screws, Part No. 3678, using two new locknuts (1), Part No. 7667. Torque each screw to 19 ft-lbs. b. Two stock screws, Part No. 3601 using two new locknuts (2), Part No.7686. Torque each screw to 9 ft-lbs

HONDA VTX1800 Complete System Installation Instructions

0

Filed Under (Uncategorized) by admin on 12-01-2011

download
You should have 2 sets on instructions, use the 2 !! -This kit includes 8 brake lines and 1 clutch hose. -1) First of all, remove gas tank and seat. -2) Remove all fluid from motorcycle, bike has 5 bleeding nipples. -3) Understand the complete stock brake system write yourself a few notes about the connections for the front caliper lines, make sure to label all lines as you remove them in case you need to re-install. -4) Set up one of the “T” block on the frame by the gas tank. -5) Remove rear stock line and stock junction block (under seat area) -6) install Galfer rear hose, (Diagram 1 ) and route it as shown in picture, use stock frame clamps to bring rear hose to the Galfer “T”. (See picture on step 4) 7) Remove stock foot brake line. Route line labeled as Diagram #2 from foot master cylinder to 3-way splitter on frame. Foot master cylinder end banjo:

Turbo+2 , Roadstar , Quantum Sport , Quantum"GL" , Entourage Owners Manual

0

Filed Under (Uncategorized) by admin on 03-12-2010

download
tracking Any parting within the tread, sidewall, or inner liner of the tire extending to cord material. CT A pneumatic tire with an inverted flange tire and rim system in which the rim is designed with rim flanges pointed radially inward and the tire is designed to fit on the underside of the rim in a manner that encloses the rim flanges inside the air cavity of the tire. Curb weight The weight of a motor vehicle with standard equipment including the maximum capacity of fuel, oil, and coolant, and, if so equipped, air conditioning and additional weight optional engine. Extra load tire A tire designed to operate at higher loads and at higher inflation pressures than the corresponding standard tire. Groove The space between two adjacent tread ribs. Gross AxleWeight Rating The maximum weight that any axle can support, as published on the Certification /VIN label on the front left side of the trailer. Actual weight determined by weighing each axle on a public scale, with the trailer attached to the towing vehicle. Gross Vehicle Weight Rating The maximum weight of the fully loaded trailer, as published on the Certification /VIN label. Actual weight determined by weighing trailer on a public scale, without being attached to the towing vehicle. Hitch Weight The downward force exerted on the hitch ball by the trailer coupler. Innerliner The layer(s) forming the inside surface of a tubeless tire that contains the inflating medium within the tire. Innerliner separation The parting of the innerliner from cord material in the carcass. Intended outboard sidewall The sidewall that contains a white-wall, bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire or the outward facing sidewall of an asymmetrical tire that has a particular side that must always face outward when mounted on a vehicle. Light truck (LT) tire A tire designated by its manufacturer as primarily intended for use on lightweight trucks or multipurpose passenger vehicles. Load rating The maximum load that a tire is rated to carry fora given inflation pressure. Maximum load rating The load rating fora tire at the maximum permissible inflation pressure for that tire. Maximum permissible inflation pressure he maximum cold inflation pressure to which a tire maybe inflated.
-9- Maximum loaded vehicle weight The sum of curb weight, accessory weight, vehicle capacity weight, and production options weight. Measuring rim The rim on which a tire is fitted for physical dimension requirements. Pin Weight The downward force applied to the 5thwheelor gooseneck ball, by the trailer kingpin or gooseneck coupler.

Incoming search terms:

Wildfire Scooter WF 250CB Owner's Manual

0

Filed Under (Uncategorized) by admin on 26-11-2010

download
• Check before Riding • Make sure the brakes work properly and adjust if necessary. • Check all nuts and bolts for tightness. • Make sure that the gas tank is full. • Check tire pressure. • Check all gauges. • Check and make sure that all of the lights are working properly, headlight, taillight, turn signal etc. • Check the engine oil. STARTING, RIDING, STOPPING AND PARKING Before starting, put the kickstand up. • Practice in an empty area away from people and vehicles. • Always remember to obey your local and state laws and regulations. • Be sure your bike has fuel and oil. • Be sure the bike is in neutral. • Apply the rear brake. • Turn the key on. • Press the electric start button. • After engine warms up, push the choke 1/4 in then 1/2 in and in 1 minute completely off. • If the engine is warm it should start without choking. • For a cold engine, let the engine idle for 1-3 minutes before driving, then begin to turn the choke off. • Never exceed 4 seconds when engaging the starter. • Release the button immediately after the engine starts. • Do not apply the key while the engine is running, it can cause damage to the starter. • Sit on the bike keeping one foot on the ground for stability, release the clutch by pulling in the lever, shift bike into first gear by using the foot shifter. • Apply the throttle gradually as you release the clutch lever slowly until the clutch engages. • To shift into the next gear release the throttle pull the clutch lever in and shift into the next gear, after you shift, gradually apply the throttle and slowly release the clutch. • Use this sequence when shifting to all gears. • Only put your feet on the ground when coming to a stop. • When coming to a stop decrease your speed by releasing the throttle and applying the brakes and the clutch, if the tire skids release the brake and reapply. • Parking: Put your kick stand down. Park away from pedestrians. NOTE: The muffler and exhaust pipe are h

Incoming search terms: