Yamaha FZ-1 TiForce exhaust system Installation Instructions (Slip-on)

0

Filed Under (Yamaha) by admin on 03-01-2012

download
Loosen the clamp where the stock tailpipe connects to the stock collector. 2. Remove the bolt holding the stock muffler assembly to the footpeg/exhaust bracket. 3. Remove the stock tailpipe and exhaust assembly as one piece. 4. Remove the nut securing the right side center stand support bolt. Install the new supplied bracket as shown in (See figure 1) 5. Remove the right rear footpeg assembly complete, bolt the new footpeg mounting bracket in place of the stock one using supplied bolts. 6. Carefully unbolt the footpeg from the bracket (Be careful there are springs and washers that will fall out if you are not careful), bolt the footpeg into the new billet footpeg bracket. Bolt the footpeg bracket to the footpeg- mounting bracket. (See figure 2) 7. Remove the stock exhaust gasket from the stock tailpipe and installthe gasket into the new tailpipe. 8. Slide the supplied clamp over the new tailpipe and slide the new tailpipe onto the stock collector. 9. Slide the TiForce end can into place. Loosely attach the two rubber bands, stainless steel bands K, and stayarm / hanger G to the end can using the supplied 6mm hardware H. See figure 4. 10. Place the bands approximately 150mm from the edge of the end can. See figure 5. 11. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 12. Attach the supplied springs to connect the tailpipe and muffler assembly. 13. Make sure the exhaust system is free and clear, if necessary jigglethe system to adjust for proper clearance. 14. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (figure 5), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure thatthe rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. 15. Tighten the supplied clamp to secure the new tailpipe to the factory collector. 16. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 17. Check that all hardware is tightened, then start the motor and check for exhaust leaks.

Yamaha FJR Backrest REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 03-01-2012

download
Motorcycling is a dangerous activity that can result in serious injury or death. Please be advised that this product has NOT been tested under every conceivable condition. While every effort has been made to design a sturdy and reliable product, numerous unpredictable conditions and/or variables could occur during its use, resulting in possible property damage, personal injury or death. By proceeding with the installation, the purchaser acknowledges that these inherent dangers and unpredictable conditions exist. Furthermore, the purchaser understands that Sargent Seat Cover Co. / D.B.A. Sargent Cycle Products N.A. shall not be held liable for any direct, indirect, incidental, special, or consequential damages arising out of or in connection with the use of this product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you. If the purchaser does not agree to all terms of this limitation of liability/disclaimer, the product may return to Sargent Cycle Products N.A. in its original packaging (within 30 days) for a full refund of the purchase price (excluding shipping and handling).

Yamaha Stratoliner 2006 3" Big Straights REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 02-01-2012

download
1. Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove bolts that are holding muffler at rear mounting bracket. 3. Remove Cables from exhaust valve. 4. Remove O2 Sensor from pipe. 5. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 6. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 7. Remove complete pipe assembly. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system. 1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. (See Illustration) 3. Install O2 Sensor onto front pipe and install front pipe onto front cylinder, taking care to not scratch chrome surfaces on pipe, engine or motorcycle. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install 3/8-16 Square nut into each slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe onto rear cylinder. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the rear cylinder head — (Remove chrome plastic valve cover to access top nut) — DO NOT TIGHTEN NUTS! 8. Install 3/8-16 Square nut into each slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration.

Incoming search terms:

Yamaha R1 2007-2008 Frame Slider Installation

0

Filed Under (Yamaha) by admin on 01-01-2012

download
Installation Steps: 1. Remove left and right body panels. 2. Remove the left side engine stud. Mount the left side offset using 99-HB-SH10125080 Socket Cap 10 X 1.25 X 80 Main Engine Stud. Tip: Only tighten enough so you can still move the offset by hand. Loosely mount the left side body panel. Adjust the offset so the frame slider when mounted will clear the bodywork. There is also a groove cut in the offset, this is so the body can clear the offset. 3. With the offset in the correct position remove body and torque down to OEM torque specs. 4. Using one drop of blue thread locker mount the left side puck to the offset with 99-HB- SH10150045 Socket Cap 10 X 1.5 X 45 (Holds puck to offset). Torque down to 30 to 32 foot lbs. 5. Remove the right side engine stud. Mount the right side offset using 99-HB-SH10125080 Socket Cap 10 X 1.25 X 80 Main Engine Stud. Tip: Only tighten enough so you can still move the offset by hand. Loosely mount the right side body panel. Adjust the offset so the frame slider when mounted will clear the bodywork. There is also a groove cut in the offset, this is so the body can clear the offset. 6. With the offset in the correct position remove body and torque down to OEM torque specs. 7. Using one drop of blue thread locker mount the right side puck to the offset with 99-HB- SH10150045 Socket Cap 10 X 1.5 X 45 (Holds puck to offset). Torque down to 30 to 32 foot lbs. 8. Mount left and right bodywork

Incoming search terms:

Yamaha YZ400/426F Camshafts REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 01-01-2012

download
Cleanliness is always a good place to start. Make sure the motorcycle is cleaned thoroughly before you start. It would be advisable to use an engine degreaser on the frame and the engine. This will ensure a clean engine during the assembly process and less of a chance of thread damage and/or dirt contamination in the engine during reassembly. And as always, replace any fiber-based gasket that was moved in any way, i.e.: cam chain tensioner. You will need basic hand tools and a torque wrench, machine towels (rags), some cleaning solvent, and a cam chain tensioner gasket. And the Hot Cams’ Degree Wheel Kit if you so desire. We will start by removing the tank and seat, top engine mount, and the cam cover. Remove the crankshaft cap and timing hole cap on the left engine case cover. Remove the spark plug. Rotate the engine in a counter clockwise (CCW) direction. Position the engine on top dead center (TDC) using the mark on the flywheel or better yet a degree wheel using a positive stop. Be sure to notice that the intake valves were the last to move, this will ensure the engine of being on “true” TDC. True top dead center occurs when both the intake and exhaust valve are closed when the piston is at TDC. This is technically the end of the compression stroke and the Page 1
beginning of the power stroke. The “artificial” TDC is during the overlap when both the intake and exhaust valves would be open. Note the positioning of the cam lobes (their included angle will be close to 170 degrees), this will help during the installation of your new Hot Cams camshafts Remove the cap bolt on the end of the cam chain tensioner block, be aware of the copper washer. Release the spring tension on the cam chain tensioner by turning the flat blade screw slot inside the adjuster block in a clockwise (CW) direction; it will lock in the retracted position. Remove the two 8mm headed bolts that hold the cam chain tensioner to the cylinder block. Remove and discard the gasket. Remove the 4 bolts that hold the exhaust cam cap in place, lift the cam cap off. It may be necessary to pry very lightly on the cap to lift it off its dowel pins. Do not use the cam lobes as the pry point. Be careful not to drop the dowels and also be careful to not lose the half moon shaped retainer for the bearing under the cam cap. Remove the 6 bolts that secure the intake cam cap and lift the cam cap off the camshaft, again, be careful to not drop the retainer or dowels. Lift the intake camshaft out of its pocket in the cylinder head casting. Remove the cam chain from the sprocket, set the stock camshaft aside. Lift the exhaust camshaft out of its pocket in the cylinder head casting and remove the chain from the sprocket. Do not drop the cam chain, dangle it over the side of the engine while keeping slight upward pressure on the chain to maintain its position on the drive sprocket on the crankshaft

Incoming search terms:

Yamaha V-Star 1300 Receiver Hitch Installation

0

Filed Under (Yamaha) by admin on 01-01-2012

download
Install all bolts loosely until all brackets are in place Remove accessories (saddle bags, back rests, etc) before hitch installation. 1) Place motorcycle on a firm level surface and secure in a upright position. 2) Remove saddle bags and saddle bag hardware (Tourer model only) Also remove rear riders pegs (Tourer model requires removal of rear footpeg offset hardware as well) 3) Attach bracket A (right) / B (left) to rear footpeg attachment point using new bolts provided. Remount footpegs/saddlebag hardware over top of brackets A/B. NOTE: Do not attach leveling stand bracket at this time
4) Attach bracket C(right) / D(left) to rear fender sub frame using new bolts provided. (Tourer model only – Saddle bag hardware mounts to the outside of brackets C/D. Brackets C/D mount between chrome side rail and saddlebag hardware.) NOTE: Brackets C/D have welded spacers which attach in toward rear fender 5) Attach top of Bracket E(right) / F(left) to rear of brackets C/D. Brackets E/F mount to the inside of brackets C/D. NOTE: Use ½ inch spacer between brackets E/F and C/D on Tourer model ONLY
6) Attach rear of brackets A/B to TOP of forward hitch arms. Attach bottom to brackets E/F to rear hitch plate. 7) Carefully tighten all bolts at this time ensuring hitch is square with motorcycle.

Yamaha TTR 250 Dual Sport Kit Installation

0

Filed Under (Yamaha) by admin on 31-12-2011

download
1. Get a degree in Mechanical and Electrical Engineering. (Just kidding!) 2. Remove the seat, side panels, and gas tank. If you are color blind or even think you might be a little color blind, now is the time to get someone to assist you. Successful installation of the kit requires good color recognition. You want to go riding this weekend, don’t you? Photo 1 3. Unplug the yellow, blue and black taillight wires from the stock wiring harness (Photo 1). 4. Unplug the headlight from the stock wiring harness and remove. 3 Photo 2 5. Remove the headlight on/off switch. Unplug the red two pin connector with yellow and brown wires (Photo 2) from its mate that was under the fuel tank. 6. Clip the zip tie holding the headlight leads to the fork tube, coil it up and secure it to the frame in front of the voltage regulator as shown in Photos 3 and 4. Remove bracket shown in Photo 3. 4 Headlight Leads Remove this bracket Photo 3 Coil up wires and secure with a zip tie Photo 4 7. Rear Turn Signal Installation: Turn signal mounting requires that you drill a 3/8 inch hole in either side of the rear fender near where it meets the side panels. You can achieve a clean, durable installation using this mounting location. Mount the rear turn signals by drilling a 3/8 hole in the rear fender in the location shown in Photo 5 and Photo 6. Use the templates provided at the back of this instruction manual to determine the hole locations. Note that you will also be drilling a 3/16 hole on each side as well. You may find it easier to remove the fender to drill and attach the turn signals rather than performing this modification while the fender is on the bike

Incoming search terms:

2001-2003 XV16 Fuel Pump and Carburetor Removal

0

Filed Under (Yamaha) by admin on 31-12-2011

download
Disconnect the carburetor fuel line hose at the fuel pump. •Disconnect the fuel pump wire coupler. •Remove the choke cable from fuel pump bracket. •Remove the upper engine mount, leaving the fuel pump attached to the mount. •Disconnect the TPS and carburetor wire couplers.       Disconnect the throttle cables, and then remove the carburetor. NOTE: The idle adjuster can be removed from its bracket without loosening the bracket screws. PAGE 3 of 12 HIDDEN 6mm SCREW 6mm BOLT UPPER ENGINE MOUNT/ FUEL PUMP CARBURETOR PAGE 4 of 12 Right-Hand Footrest Removal: •Disconnect and remove the brake light switch. •Remove the forward-most tie wrap around the brake hose and frame. •Remove the footrest assembly. NOTE: Leave the brake hose attached. Move the hose to the underside of the foot rest mount and support it as necessary so that it is out of the way Cylinder Head Oil Pipe Removal/ Installation: •Slightly loosen all three banjo bolts before removing them to prevent oil line deformation. NOTE: When loosening the upper banjo bolts, hold the line in place using a wrench at the flat surface on the fitting. Air Injection System (AIS) Removal: •Remove the electric starter motor. •Remove the regulator/rectifier assembly. Remove the AIS pipes from the cylinder head, but leave them attached to the AIS assembly. •Remove the three screws with 8mm heads, and then remove the AIS air filter from the right side. •Remove the three Phillips head screws holding    the AIS assembly on the frame. •Remove the AIS assembly from the left side. FOOTREST ASSEMBLY UPPER BANJO BOLT AIS AIR FILTER AIS ASSEMBLY
PAGE 5 of 12 Transfer Case Removal: •Remove the transfer case bracket first. Then remove the outer chrome cover, inner cover, and drive-sprocket nut. NOTE: There is a sealing washer between the inner case and the transfer case at the 8mm stud. Be sure to replace it during re-assembly. •Remove the two chrome oil lines between the engine and oil tank. NOTE: Retain the four O-rings for re-use. •Remove the drive pulley cover and remove the drive pulley nut. •Loosen the drive belt tension. •Remove the drive pulley, inner cover, collar, and O-ring. NOTE: The collar has a bevel on its inside diameter     for the O-ring facing inward and a bevel on the outside diameter facing the pulley. •Remove the drive and driven sprockets with chain as an assembly. •Remove the collar and O-ring. NOTE: Collar has a bevel on its inside diameter that faces inward for the O-ring. •Remove oil tank filler neck. •Remove the relay bracket on the right-hand side. NOTE: Leave the relays connected. Simply move them out of the way to allow room for transfer case removal. •Slide the transfer case out from the right side.

Incoming search terms:

YAMAHA ROYAL STAR VENTURE CENTERSTAND REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 31-12-2011

download
Stand Installation. Locate the four mounting holes on the frame that correspond with the holes in the centerstand. Slide the front of the centerstand up into the frame and align the large bolt holes with those in the frame. Install the (2) 7/16″ x 1″ bolts with washers thru the frame and centerstand. Install the (2) 7/16″ nuts and make finger tight. (on California models the fuel tank vent canister must be removed and the hoses bypassed see note below) Pivot the rear of the centerstand up to align the (2) smaller holes in the stand with those in the frame. Insert a phillips screwdriver into one of the (2) remaining mounting holes and pry the other hole into alignment. Install one of the ¼” x ¾” bolt with a washer from the top down thru the frame and centerstand. Install the lock nut finger tight. Remove the screwdriver and install the remaining ¼”x¾” bolt washer and nut. Tighten the ¼ ” bolts securely 10-12 ft. lbs., then tighten the 7/16″ bolts securely 20-24 ft. lbs. 2. Stop Bumper Installation. Next install the centerstand-stop bumper and bracket onto the frame. Locate the bolt “A” in photo #1. Notice there is another 10 mm bolt just below it. Remove the lower bolt. Attach the bumper bracket to this hole using the longer bolt and washer supplied. The leg of the bracket with the bumper should face inward towards the center of the motorcycle. Adjust the height of the bracket to keep the pedal arm 3/8″ to ½” from the bottom of the exhaust pipe. Tighten securely. 3. Emissions Valve Relocation. You will notice that the right leg of the stand near the foot comes in contact with the emissions valve. The valve needs to be moved outward or to the right as you are sitting on the motorcycle approximately ¾”. This is done as follows: Remove the (2) 10 mm bolts holding the emission valve and bracket to the frame. See photo #2. With the hoses still attached pull the valve down to gain access to the (3) allen screws. Remove the (3) allen screws and (2) nuts holding the bracket to the valve, turn the bracket over and re-assemble the valve onto the bracket as shown in photo #3. Re-install the valve onto the frame. You may need to rotate the hose clamp clips out of the way and/or bend the entire valve bracket assembly outward slightly to gain clearance between the centerstand leg and foot. 4. Using Your New Centerstand. To put the motorcycle up onto the centerstand, hold the left handle bar and saddlebag guard rail. Using the ball of your right foot, lower the stand to the ground. Rock the motorcycle from side to side slightly until you feel both feet of the stand touching the ground. Now, put all of your weight on to the centerstand pedal (stand on it). Pull up and back on the grab rail using a rocking motion to rock the motorcycle up on to the stand. Remember it is a matter of using your body weight and leverage not lifting! 5. Getting the Bike Down off the Centerstand. Holding the left handle bar and saddlebag guardrail, firmly rock the motorcycle off the centerstand. You can also rock it off while sitting on the motorcycle.

Yamaha XV-1900 Braided Stainless Steel Thottle Cables Installation Instructions

0

Filed Under (Yamaha) by admin on 30-12-2011

download
Please read and understand these instructions completely before installation to avoid injury or damage to the motorcycle or accessory. IMPORTANT: Dealer installation is recommended. The installer should have the service manual for the motorcycle , as well as a good understanding of motorcycle service and repair techniques. Dealer: These instructions contain important information for future reference and must be given to the customer. 1. Parts List: Item Part Name Part Number Description Qty 1 Throttle Cable Set 07-1083 1 2. Preparation: a) Before installation, lubricate cable with an appropriate cable lube such as Motion Pro Cable Lubricant (P/N 15-0002) b) Securely place motorcycle on side stand 3. Installation: Refer to vehicle service manual for installation instruction and adjustment procedures. NOTE: Notice how original cable routed before removing it. Install the accessory cable in the same way. If unsure or original cable routing, refer to the cable routing diagram in the service manual. WARNING ∞ Before starting the engine, be sure the throttle operates smoothly and check that throttle body is fully closed when throttle is released ∞ After starting the engine, turn the handlebar to the right and to the left to be sure the throttle operation is not affected ∞ Improper installation could result in great bodily injury or death 4. Maintenance: Check throttle operation before each ride. Follow Periodic Maintenance procedures in the owner’s manual for adjustment and lubrication. 5. Care and Cleaning: See your Owner’s Manual