1999-2008 FLHT Series Harley- Davidson Trike Conversion Kit Installation Instructions


Filed Under (Harley Davidson) by admin on 04-12-2010

1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect negative Battery Terminal. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Save the Passenger Handrail and two nuts. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove five ¼ – 20 HHCS, ¼ – 20 nyloc nuts, and Aluminum Spacers. 13. Remove Tour Pak from Top Support Tube. 14. Loosen Muffler Clamp on both Mufflers and remove 2 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 15. Remove and discard Muffler Support Plates. 16. Remove both ¼ – 20 HHCS and Front Saddle Bag Brackets. 17. Remove the twelve 5/16 – 18 Torx HCS six 5/16 – 18 nuts, and the Left and Right Saddle Bag Guards. 18. Remove the Air Line Junction from the Rear Fender. 19. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip.
6 20. Remove two 5/16 – 18 Phillips head screws. Remove the Left and Right Frame Covers. 21. Remove two 5/16 – 18 Torx HCS. Remove and save the Top Tour Pak Support Tube Top. 22. Remove four 5/16 – 18 Torx HCS. Remove the Left and Right Rear Saddle Bag Guard Support Bracket. 23. Remove four 5/16 – 18 HHCS. Remove and save the Tour Pak Support Tube Bottom. 24. Remove and discard the Air Valve Assembly Bracket. 25. Remove four ½ – 13 HHCS and washers. Remove and discard both Rear Air Shock Absorbers. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. 26. Drain all Brake Fluid from the Rear Brake System. 27. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 28. Remove the 10 – 24 flanged HHCS and Rear Brake Hose Clamp from the Right Rear Fork Bracket. 29. Remove ¼ – 20 SHCS from Rear Stop Lamp Switch Bracket. 30. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 31. Remove the Spring Clip and nut from the Rear Axle. 32. Remove Rear Axle and Rear Wheel Spacers. 33. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 34. Remove Rear Brake Caliper. 35. Slide Rear Wheel Assembly rearward. Remove one 5/16 – 18 Torx HCS from inside the Rear Fender well. 36. Slide Rear Wheel Assembly forward. Remove two 5/16 – 18 Torx HCS. Remove Rear Fender. 37. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate

Incoming search terms:

Comments are closed.

Incoming search terms: