HARLEY DAVIDSON BILLET HEADLAMP WITH SHORT/ TALL MOUNTS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
Kit 68593-06 is a 5-3/4 inch headlamp and kit 69851-06 is a 4-1/2 inch headlamp. Both kits will fit the models listed in Table 1. Table 1. Short and Tall Mount Kits Models Kits 1984-1999 FXSTC, 1998- Later FXST/B, and 2000-Later FXSTD; 1994-2005 FXDWG Short Mount Kit 68595-06 1996-Later XL 1200C and 1998-Later XL 883C; All 2006 Dyna Models; 1999-2000 FXR2/3/4 Tall Mount Kit 69611-06 Additional Parts Required This kit also requires the separate purchase of a Short or Tall Mounting Kit 68595-06 or 69611-06 for your model motorcycle, and can be purchased from a Harley-Davidson dealer. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 21, Table 2 and Figure 22, Table 3. REMOVAL Remove Headlamp and Mounting Bracket for Softail Models To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative (-) battery cable. 2. Remove fuel tank. Refer to FUEL TANK in Service Manual. 3. Disconnect 4-place headlamp connector [38] from main wire harness. Headlamp connector is located under fuel tank on left side. 8 5 7 5 6 2 1 3 4 is01835 1. Screw 2. Washer 3. Nut 4. Lockwasher 5. Washer (2) 6. Screw 7. Mounting block 8. Headlamp assembly Figure 1. Softail and Dyna Headlamp Assembly with Mount (except FXSTD) NOTE All Softails (except FXSTD) complete steps 4 through 6. For FXSTD models complete steps 7 through 9 4. All Softails (except FXSTD): See Figure 1. Remove screw (1) and washer (2) from stem and bracket. Discard screw but save washer for later use. 5. Remove and discard mounting block (7) and headlamp assembly (8). 6. FXSTD models: See Figure 2. Remove screw (1) and washer (2) from stem and bracket. Save screw and washer for later use. 7. Remove and discard nut (3), washers (4), and screw (5). 8. Remove and discard mounting block (6) and headlamp assembly (7). 7 3 4 2 1 4 6 5 is01838 1. Screw 2. Washer 3. Acorn nut 4. Washer (2) 5. Screw 6. Mounting block 7. Headlamp assembly Figure 2. FXSTD Headlamp Assembly with Mount Remove Headlamp and Mounting Bracket for Dyna Models 1. Remove seat following the instructions in the Service Manual. 2. Disconnect negative (-) battery cable. 3. Remove fuel tank. Refer to FUEL TANK in Service Manual. 2 1 is01750 1. Cable strap 2. Wire harness Figure 3. Dyna Service Loop (2005-Earlier) 4. 2005-Earlier FXDWG: See Figures 3 and 4. Remove plug on right side of top frame tube. At service loop, remove cable clip and push wire harness into top frame tube. Pull connector out from hole on right side of tube. 2006-Later FXD: See Figure 5. Remove cover under top frame tube, then pull connector out from opening under tube. 5. Disconnect 4-place headlamp connector [38] from main wire harness

Comments are closed.