0 offset 1st gen 4runner

You search Auto repair manual PDF 0 offset 1st gen 4runner, if there are search results will appear below. If search results do not exist, please search by others keyword.



  0 offset 1st gen 4runner Direct Download speed 5282 Kb/s

  0 offset 1st gen 4runner Full Version speed 6162 Kb/s



Yamaha R1 2007-2008 Frame Slider Installation

0

Filed Under (Yamaha) by admin on 01-01-2012

download
Installation Steps: 1. Remove left and right body panels. 2. Remove the left side engine stud. Mount the left side offset using 99-HB-SH10125080 Socket Cap 10 X 1.25 X 80 Main Engine Stud. Tip: Only tighten enough so you can still move the offset by hand. Loosely mount the left side body panel. Adjust the offset so the frame slider when mounted will clear the bodywork. There is also a groove cut in the offset, this is so the body can clear the offset. 3. With the offset in the correct position remove body and torque down to OEM torque specs. 4. Using one drop of blue thread locker mount the left side puck to the offset with 99-HB- SH10150045 Socket Cap 10 X 1.5 X 45 (Holds puck to offset). Torque down to 30 to 32 foot lbs. 5. Remove the right side engine stud. Mount the right side offset using 99-HB-SH10125080 Socket Cap 10 X 1.25 X 80 Main Engine Stud. Tip: Only tighten enough so you can still move the offset by hand. Loosely mount the right side body panel. Adjust the offset so the frame slider when mounted will clear the bodywork. There is also a groove cut in the offset, this is so the body can clear the offset. 6. With the offset in the correct position remove body and torque down to OEM torque specs. 7. Using one drop of blue thread locker mount the right side puck to the offset with 99-HB- SH10150045 Socket Cap 10 X 1.5 X 45 (Holds puck to offset). Torque down to 30 to 32 foot lbs. 8. Mount left and right bodywork

Incoming search terms:

2003 – 2007 4Runner OIL LEAK FROM FRONT TIMING COVER

0

Filed Under (Toyota Manuals) by admin on 31-10-2011

download
evidence of a small oil leak located where the Bank 1 cylinder head, engine block, and timing cover meet. Use the following repair procedure to address this condition. 2003 – 2007 model year 4Runner vehicles equipped with the 1GR-FE engine and produced BEFORE the Production Change Effective VINs shown below. MODEL PLANT DRIVETRAIN PRODUCTION CHANGE EFFECTIVE VIN 2WD JTEZU17R#68064608 Hino 2WD JTEZU14R#78076191 4Runner Hino 4WD JTEBU14R#78078323 4Runner 4WD JTEBU14R#78090468 Tahara 2WD JTEZU14R#70091230 Tahara 4WD JTEBU14R#70117349 OP CODE DESCRIPTION TIME OFP T1 T2 EG7036 Reseal FrontTiming Cover with FIPG 2WD7.6 113100P0306548 EG7036 Reseal Front Timing Cover with FIPG 4WD8.5 11310-0P030 65 48 Applicable Warranty*: This repair is covered under the Toyota Powertrain Warranty. This warranty is in effect for 60 months or 60,000 miles, whichever occurs first, from the vehicle’s in-service date. *Warranty application is limited to correction of a problem based upon a customer’s specific complaint

Incoming search terms:

Kawasaki ZX6R 2009 Frame Slider Installation and removal Instructions

0

Filed Under (Kawasaki) by admin on 08-05-2012

download
1. Remove mid and lower body panels Left and Right. There is a small plastic cover that is mounted over the main engine stud location on the left side. This cover requires a small notch to be cut out of the cover to clear the small end of the left side offset. Remove stock stud and mount the left side offset (with 10 X 1.25 X 60). Using a pencil, trace out the notch that you need to remove to clear the small end of the offset. We used a Dremel tool with a sanding roll and cleaned it up with an exacto knife. We removed a small amount of material at a time checking for clearance each time. The notch will not be visible after the body has been mounted. See photos below: 2. Once you have notched the small left side panel, mount the left side offset but only hand tight. You need to be able to move the offset by hand to its proper location. 3. Mount the left side bodywork and align the offset to the opening in the body. Mount the left side slider on the offset to ensure correct location. There is a flat notch in the slider so the body will clear. Remove the slider and body and torque down the offset to OEM specifications. (see above)
4. Mount the left side panel. Install the slider using one drop of blue thread locker and torque down to 30 to 32 ft lbs.

2003 – 2004 4Runner, 2004 Highlander, Prius, Sienna And Solara POWER WINDOW / ROOF INITIALIZATION PROCEDURES

0

Filed Under (Toyota Manuals) by admin on 17-10-2011

download
Turn the ignition switch ON. 2. Open the window halfway by pressing the power window switch. 3. Fully pull up the switch until the power window is fully closed and continue to hold the switch for at least three (3) seconds after the power window is fully closed. 4. Check that the “AUTO UP/DOWN” function operates normally. B. Back Door Power Window (4Runner) 1. Turn the ignition switch ON. 2. Open the back door glass. 3. Press the back door power window switch until the door glass is fully closed and continue to hold the switch one (1) second or more after the door glass is fully closed. 4. Check that the “AUTO UP/DOWN” function operates normally. C. Power Sliding Roof (4Runner, Sienna, Solara) 1. Turn the ignition switch ON. 2. Initialize the sliding roof by pressing and holding the TILT UP switch until the roof glass tilts upward fully (the roof glass automatically tilts downward slightly after fully tilting upward). 3. Release the switch. 4. Check that the “AUTO OPEN/CLOSE” function operates normally

Incoming search terms:

2004 – 2006 4Runner TIRE PRESSURE SENSING TRANSMITTER ACTIVATION PROCEDURE DURING PDS

0

Filed Under (Toyota Manuals) by admin on 29-10-2011

download
pressure data is transmitted through a Tire Pressure Warning System antenna to the Tire Pressure Monitoring System receiver. The tire pressure sensing transmitter used for the Tire Pressure Monitoring System (TPMS) on 2004 – 2006 model year 4Runner vehicles needs to be activated during Pre-Delivery Service (PDS). 2004 – 2006 model year 4Runner vehicles. NOTE: After all the tire pressure sensing transmitters are activated, the flashing Low Tire Pressure Warning Light goes OFF. The Diagnostic Trouble Codes (DTCs) listed below may be stored in the system until the tire pressure sensing transmitters are activated. The codes will automatically clear when the tire pressure sensing transmitters are activated

Incoming search terms:

2003 – 2008 4Runner AND 2007 – 2008 FJ Cruiser FRONT AND REAR DIFFERENTIAL GEAR OIL SPECIFICATION CHANGE

0

Filed Under (Toyota Manuals) by admin on 14-11-2011

download
75W-85 GL5 synthetic gear oil beginning with the 2008 model year. This new synthetic gear oil is compatible with 2003 – 2007 model year 4Runner and 2007 model year FJ Cruiser differentials. Please refer to the Parts Information section below for information about this gear oil and use this gear oil (or equivalent) when filling front or rear differentials with oil. 2003 – 2008 model year 4Runner vehicles. 2007 – 2008 model year FJ Cruiser vehicles. PREVIOUS PART NUMBER CURRENT PART NUMBER PART NAME TYPE QTY N/A 08885-02606 Toyota Genuine Differential Gear Oil LX 75W-85 API GL-5 SAE 75W-85 LSD As Needed N/A 08885-02506 Toyota Genuine Differential Gear Oil LT 75W-85 API GL-5 SAE 75W-85 w/o LSD As Needed Refer to the diagram below to identify if LSD or non-LSD gear oil is used on the vehicle. For applicable vehicles, there is a caution label above the filler plug, as shown below

Incoming search terms:

2003 – 2007 4Runner SUPPLEMENT DAYTIME RUNNING LIGHTS REPAIR MANUAL

0

Filed Under (Toyota Manuals) by admin on 12-10-2011

download
2003 – 2007 model year 4Runner vehicles with the DRL factory option. 2003 – 2007 model year 4Runner vehicles equipped with the DRL factory option (RL accessory code). ITEM NO. SPECIAL SERVICE TOOLS (SSTs) PART NUMBERQTYDRW** 1 Toyota Diagnostic Tester Kit* NOTE: All components from this kit/set are required. 12 Megabyte Diagnostic Tester Program Card (P/N 01002593-005) with version 13.4a Software (or later) is required. TOY220036 1 9 2 CAN Interface Module Kit* NOTE: All components from this kit/set are required. 01002744 1 9 *Essential SSTs. **Drawer number in SST Storage System

1999 – 2001 TOYOTA 4Runner UNINTENDED POWER REAR WINDOW ACTIVATION

0

Filed Under (Toyota Manuals) by admin on 13-10-2011

download
or accidental rear window activation. In order to address these concerns, an updated Back Door ECU and Wireless Transmitter have been adopted. 1999 – 2001 model year 4Runners with factory keyless entry systems. MODEL PLANT STARTING VIN ENDING VIN REPAIR PROCEDURE 4Runner V64WD Tahara JT3HN8#R#X0194234 JT3HN8#R#10338020 1 & 2 V6 4WD JT3HN8#R#10338021 JT3HN8#R#10353976 1 Only Hino JT3HN8#R#X9018626 JT3HN8#R#19050479 1 & 2 JT3HN8#R#19050480 JT3HN8#R#19056468 1 Only 4Runner V62WD Tahara JT3GN8#R#X0092242 JT3GN8#R#10194008 1 & 2 V6 2WD JT3GN8#R#10194009 JT3GN8#R#10211000 1 Only NOTE: Please determine where the vehicle falls in VIN range above, and order ONLY the parts associated with the Repair Procedure number(s) listed. (Please refer to the “Parts Information” section on page 2 of this bulletin.

2003 4Runner And Land Cruiser, 2004 Sienna SERVICE MAINTENANCE REMINDER LIGHT RESET PROCEDURE

0

Filed Under (Toyota Manuals) by admin on 26-10-2011

download
should be used to reset the light when the oil has been changed. 2003 model year 4Runner and Land Cruiser vehicles. 2004 model year Sienna vehicles. To reset the Service Maintenance Reminder Light: 1. Turn the ignition switch to the “ON” position. 2. Set the Odometer / Trip Display to the “ODO” mode. 3. Turn the ignition switch to the “OFF” position. 4. Depress and hold the Trip Meter “RESET” button while turning the ignition switch to the “ON” position. 5. The Service Maintenance Reminder Light will: a. Illuminate solidly for 3 seconds. b. Blink for 2 seconds. c. Illuminate solidly for 1 second. d. Turn off. 6. Release the Trip Meter “RESET” button. 7. Turn the ignition to the “OFF” position. 8. Turn the ignition to the “ON” position, and confirm that the Service Maintenance Reminder Light goes out

Incoming search terms:

Dual Battery Installation for 1985 Toyota 4Runner

0

Filed Under (Toyota Manuals) by admin on 16-09-2011

Download
I reviewed a number of locations on my 4Runner including the engine bay, under the body
and rear cargo area. Of all those areas, I decided on the engine bay as the most convenient,
the safest location and the easiest to wire and protect the batteries. Careful measurement of
the OEM battery location showed that by rotating the OEM battery 90 degrees, another
battery could be shoehorned in with some minor modifications. See figure 1 for a photo of
the OEM battery location.
The first problem to solve when mounting batteries in this location is to move the OEM fuse
box approximately 1” towards the rear of the truck. See figure 2 on how I was able to move
my fuse box 1” inch. There is just enough slack in the factory wiring harness to make this
move without having to redo wiring harnesses or putting undo pressure or tension on the
harness

Incoming search terms: