02 harley xl 883 cut off exhaust cross bar stock

You search Auto repair manual PDF 02 harley xl 883 cut off exhaust cross bar stock, if there are search results will appear below. If search results do not exist, please search by others keyword.



  02 harley xl 883 cut off exhaust cross bar stock Direct Download speed 5282 Kb/s

  02 harley xl 883 cut off exhaust cross bar stock Full Version speed 6162 Kb/s



Harley-Davidson Sportster 883/ 1200 Straightshot HS Exhaust system REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Loosen the heat shield clamps on both the front and rear exhaust pipes. This allows easier access to the head pipe mounting nuts. 2. Remove the two head pipe mounting nuts from each flange, located at the cylinder head. 3. Remove the two bolts from each muffler body which attach the muffler bodies to the mounting bar. 4. Remove the clamp bolt which mounts the rear head Page 1 of 4 D445N Rev. 1.0 Sportster 883/1200 Straightshot HS Exhaust system Part #17815 U S A Congratulations, you have purchased the finest exhaust system available for your motorcycle. Your VANCE & HINES exhaust system is designed and crafted for maximum performance, a perfect fit, a great sound and unbeatable style! Please follow the installation instructions below and if you have any questions, feel free to call our technical help line (562) 926-5291. Attention Installer: (if other than owner): Please forward this instruction sheet to the purchaser of this product. These instructions contain valuable information necessary to the end user. Tools required for installation: 3/16″ & 5/16″ Allen wrenches 3/16″ & 5/16″ Allen & 1/2″ sockets 3/8″ Ratchet & Extensions T30 Torx driver 1/2″ Wrench 5/16″ nutdriver/flat blade screwdriver Ft/lb. & In/lb. Torque wrenches Snapring pliers pipe to the belt drive cover bracket and carefully remove both exhaust pipes from the motorcycle. 5. Remove the drive belt cover and take the bracket off the rear cover bolt, it will not be re-used. 6. Loosen the brake rod at the rear eyelet using a T30 Torx driver. 7. Remove the exhaust mounting bar, saving the three mount bolts and washers for re-use. 8. Using snapring pliers, carefully remove the flanges and circlips from the stock exhaust system. Save for re-use. NOTE: If circlips look bent or twisted replace them with new circlips. VANCE & HINES EXHAUST SYSTEM INSTALLATION 1. Check condition of stock exhaust gaskets. Replace if damaged or worn. Vance & Hines recommends you replace your gaskets with Screamin’ Eagle gaskets part number 17048-98. 2. Install and tighten supplied mounting bracket (stamped 356-P) using stock bolts and washers (Figure 1). Torque to 30-33 Ft/Lbs. NOTE: Support the rear of the bracket during tightening to insure it is aligned with the bottom edge of the frame. 3. Re-install drive belt cover. Torque to 1 x 3/8″ bolt 30-33 Ft/Lbs. 2 x 1/4″ bolts 80-120 In/Lbs. 4. Re-install brake rod eyelet using blue thread locking compound (Loctite® 243). There is a 1/2″ clearance hole in the bracket to allow access for tightening brake rod eyelet. Torque to 120/180 In/Lbs. (Figure 1). 5. Remove header pipes and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark outside edge of each heat shield to show location of mounting clips where hose clamps will loop through (Figure 2). 6. Install circlips and flanges from the stock system onto both new head pipes.

Incoming search terms:

Harley Davidson Sportster 2 into 1 SS2 R Race Exhaust System Instalation Manual

0

Filed Under (Harley Davidson) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the heat shield clamps on both front and rear exhaust pipes. 2. Remove the two mounting nuts from each head pipe, located at the cylinder head. 3. Remove the nut that mounts the front muffler to the engine, located below the rear brake pedal. 4. Remove the bolt that mounts the rear muffler to the mounting bar. 5. Remove the entire exhaust system and set it aside. 6. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. Note : If circlips look bent or twisted replace them with new circlips. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Remove the acorn nut that mounts the top of the right rear shock to the frame. 2. Install the large angle cut end of the new mounting bar to the shock bolt (with the shock in place). Replace the acorn nut but leave it loose at this time. Note : Check the clearance between the mounting bar and the shock. Space the mounting bar out with a washer (not supplied) if needed. 3. Install the circlips and flanges from the stock system onto both of the new head pipes. 4. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 5. Install new header using the stock nuts and tighten them evenly. 6. Slide the tailpipe of the new exhaust system over the collector of the front header. 7. Install two of the exhaust springs (supplied) between the collector and the tailpipe using the spring puller tool (supplied). 8. Slip the silencer over the tailpipe while aligning the hole in the mounting bar with the hole on the top of the muffler, with the muffler positioned to the outside of the mounting bar. 9. Install the bolt, washers and lock nut (all supplied) through the muffler and mounting bar. 10. Install the two exhaust springs over the tabs on the muffler and tailpipe using the spring puller tool. 11. Tighten the acorn nut on the top of the right rear shock. 12. Be sure to tighten all hardware before starting your motorcycle. 13. Important: Check to be sure that there is adequate clearance between the head pipe and the rear

SUZUKI M109 1800 cc EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 10-11-2010

download
1. Remove the seat and right side fairing cover (with M109 insignia), behind the fuel tank. To remove the fairing, release the plastic peg on top by pushing the center inward and pulling the fairing upwards until the peg releases, remove the M6 button head bolt at the bottom of the fairing. Pull the fairing outward from the rear and upward near the plastic peg to release it. Once it is free from all plastic pegs pull it forward to release it from the bottom of the fuel tank. 2. Remove the right side cover above the exhaust-mounting bracket secured by one M6 button head bolt, retain bolt for later. Remove the chrome steel cover above the exhaust secured by two remaining bolts, (this chrome piece will no longer be used.) Remove the large left rear rubber grommet and flanged steel collar from this chrome piece, to do this press the steel collar out of the rubber grommet first, once the collar is removed push the rubber grommet out of the wire loop on the chrome piece, set aside for later use. 3. Locate the exhaust valve actuator solenoid and harness and disconnect the black 3-prong electrical connector and white 2-prong electrical connector. 4. Remove the socket head bolts securing exhaust flanges to cylinder heads, set these fasteners aside for later use in reassembly. Support the weight of the exhaust system and remove the 2, 8 mm bolts and one 8 mm nut securing the exhaust mounting bracket and exhaust assembly. Keep these fasteners for use later. Remove the stock exhaust system as one complete unit; this includes the stock exhaust bracket, headpipes and muffler, exhaust valve solenoid and cables. 5. The exhaust valve actuator solenoid must now be removed from the stock exhaust-mounting bracket. To perform this, loosen the two nuts securing each cable to the exhaust valve cable-mounting tab, Position A in Figure 1. Make enough slack in the cables so that the ends of the cables’ threaded sheath may be disengaged from the end of the mounting tab. Now remove the two M6 hex head bolts securing the solenoid to the stock exhaust bracket. The stock exhaust mounting bracket, headpipes and muffler and exhaust valve solenoid cables will not be used anymore with the your new Cobra Exhaust System. 6. Remove the dust cover from the solenoid to expose the rotating cam and cables. DO NOT TRY TO ROTATE THE CAM RELATIVE TO THE ACTUATOR SELENOID TO REMOVE THE CABLES; DOING SO MAY DAMAGE THE INTERNAL COMPONENTS OF THE SOLENOID. To remove the cables from the cam, use the slack in the cables obtained in Step 5 to disengage the cable barrels from the cam, see Figure 1. THE DUST COVER WILL NOT BE REINSTALLED. 7. Now prepare the exhaust valve actuator solenoid for reuse. SECURELY HOLD THE CAM TO PREVENT IT FROM ROTATING IN THE SOLENOID. WHILE PREVENTING THE CAM FROM ROTATING, remove the 10 – 32 flange bolt securing it, see Figure 2. Replace the cam with the Cobra supplied cam, BE SURE TO PREVENT THE CAM FROM ROTATING WHEN REINSTALLING THE BOLT, OTHERWISE DAMAGE MAY OCCUR TO THE SOLENOID , see Figure 3. Torque to factory specifications.

Incoming search terms:

Harley-Davidson V-Rod Destroyer Indy Series Exhaust REMOVAL AND INSTALLATION

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
STOCK EXHAUST SYSTEM REMOVAL (DESTROYER) 1. Remove both collector bolts. 2. Remove nuts from both front and rear exhaust cylinder head flanges using a 13mm socket. 3. If the Racepak is installed, remove both O2 and EGT sensors from the front and rear head pipes. 4. Carefully remove complete exhaust from the motorcycle. STOCK EXHAUST SYSTEM REMOVAL (V-ROD) 5. Loosen clamp bolt at front of the collector using a 13mm socket. 6. Remove muffler bracket bolt using a 13mm wrench. 7. Carefully remove muffler and collector assembly from motorcycle. 8. Remove nuts from both front and rear exhaust cylinder head flanges using a 13mm socket. 9. Carefully remove head pipes from motorcycle. 10. Remove the stock exhaust flanges and circlips from both the front and rear head pipes. If the circlips are bent or twisted they should be replaced, Harley-Davidson part number #65045-01 We also recommend replacing the stock exhaust gaskets, Harley-Davidson part number #65109-01 INDY SERIES EXHAUST SYSTEM INSTALLATION 1. Identify front head pipe #7-8002. Install the stock flange and circlip. Install the exhaust gasket and front header pipe, leaving the flange nuts hand tight. 2. Repeat the above step for the rear head pipe #7-8006. 3. Slip the megaphone/collector assembly onto the head pipes, secure with the four springs supplied using the spring puller tool. 4. Rotate the exhaust so there is adequate clearance in all places. 5. Tighten the cylinder head flange nuts for both the front and rear head pipes. 6. Tighten both the EGT and O2 plugs on the front and rear head pipes. 7. Clean all fingerprints from the exhaust using a contact cleaner (or other non flammable cleaner). Fingerprints will leave stains on the pipe once the motorcycle is started. 8. You are now ready to start the motorcycle.

Incoming search terms:

HARLEY DAVIDSON SOFTAIL Shortshot Exhaust System REMOVAL AND INSTALLATION

0

Filed Under (Harley Davidson) by admin on 17-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. On FLSTC, FLSTF, FLSTN and FXSTS loosen the right hand floor board mounting bolts to gain clearance for exhaust removal and installation. 2. Loosen the heatshield clamps on both front and rear exhaust pipes. 3. Loosen the crossover pipe clamp, located between the front and rear head pipe. (This step is not necessary on 2000 models). 4. Remove the two mounting nuts from each head pipe, located at the cylinder head. 5. Remove the bolts that attach the mufflers to the frame. 6. Remove the entire exhaust system and set it aside. 7. On pre 2000 models remove the lower mounting bar. 8. FLSTN, FLSTF and FXSTD models have an upper mounting bar that must be removed in addition to the lower bar. 9. Park the motorcycle on its side stand. Remove the right side 1/4″-20 bolt which holds the lower fender in place. The fender will flex out of the way allowing the removal of the right passenger foot peg bolt. Position a floor jack under the right hand frame tube of the motorcycle below the swing arm pivot bolt. Raise the jack just enough to take the weight off the pivot bolt and remove the bolt and stock mounting bar. Set the mounting bar aside. Replace the pivot bolt and torque it between 120 -150 ft. lbs. Reinstall the passenger foot peg using the 1/2″-20 x 3″ bolt and an 1 5/8″ long spacer (supplied). 10. On 2000 year models, using a #50 Torx driver, remove the three mounting bolts, and set the mounting bar aside. (Two of the bolts are visible, the third is accessed by removing the right hand passenger foot peg.) Replace the foot peg using the 3/8″-16 x 2 1/2″ bolt and 3/4″ length spacer (supplied). 11. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. NOTE: If circlips look bent or twisted replace them with new circlips. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Vance and Hines recommends you replace your exhaust gaskets with Sceamin’ Eagle gaskets part number 17048-98. 2. Install the mounting bracket to the frame, by aligning the two 3/8″ holes in the bracket with the two holes in the frame below the right rear footrest, using the two 3/8″-16 x 3/4″ flange head bolts (supplied), do not tighten at this time. When the bracket is mounting correctly, it should bend out and away from the motorcycle, with the four holes of the bracket toward the front of the motorcycle. 3. Install the circlips and flanges from the stock system on to both of the new head pipes

Incoming search terms:

HARLEY DAVIDSON Softail Big Shots Staggered Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 20-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. If equipped, loosen the floor boards to gain clearance for exhaust removal and installation. 2. Loosen heat shield clamps on both the front and rear head pipes. 3. If equipped, loosen crossover pipe clamp, located between front and rear head pipes. 4. Remove two cylinder exhaust port flange nuts from each head pipe, located at the cylinder head. 5. Remove the bolts that attach mufflers to the frame. 6. Remove the complete exhaust system and set aside. Assistance may be required. 7. Remove stock mounting bars and brackets. 8. On models equipped with upper mounting bar attached at swing arm pivot bolt, go to step 9. If upper mounting bar is attached with two torx bolts (not swing arm bolt) go to step 10. 9. Remove right side 1/4″-20 bolt which holds lower fender in place. The fender will flex outwards allowing removal of right passenger foot peg bolt. Park the motorcycle on its side stand. Position a floor jack under right hand frame tube of the motorcycle below swing arm pivot bolt. Raise jack just enough to take the weight off swing arm pivot bolt. Remove swing arm pivot bolt and stock upper mounting bar. Replace swing arm pivot bolt and torque to 120 ft. lbs. Reinstall passenger foot peg using 1/2″-20 x 3″ bolt and 1 5/8″ long spacer (supplied). Reinstall 1/4″-20 fender bolt. 10. Using a T50 torx driver, remove the three mounting bolts and mounting bar. (Two of the bolts are visible, the third also attaches right hand passenger foot peg pivot and is accessed by removing foot peg. Reinstall foot peg using 3/8″x 2-1/2″ Allen bolt and 3/4″ long spacer (supplied). 11. Carefully remove exhaust port flanges and circlips from the stock exhaust system using snapring pliers. NOTE: Replace bent or damaged circlips. Check exhaust port gasket condition. (Recommended replacement exhaust port gaskets, Harley part number:17048-98 or 65324-83A)

Incoming search terms:

HARLEY DAVIDSON SOFTAIL 2 into 1 Pro Pipe Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 22-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the heat shield clamps on both front and rear exhaust pipes. 2. Loosen the crossover pipe clamp, located between the front and rear head pipes. 3. Remove the two mounting nuts from each head pipe, located at the cylinder head. 4. Remove the two nuts from the back side of each muffler. 5. Remove the entire exhaust system and set it aside. 6. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. Note: If circlips look bent or twisted replace them. 7. Remove the two bolts that hold the front muffler mounting bar to the frame. Note: FLSTN, FLSTF models require the removal of the stock exhaust system mounting bar. For removal: Remove the right passenger foot peg bolt. Position the motorcycle on it’s side stand with a floor jack under the swing arm pivot bolt on the right hand side. Raise the jack just enough to take the weight off the pivot bolt and remove the bolt and stock mounting bar. Replace the pivot bolt and torque it between 120 -150 ft. lbs. 8. Reinstall the foot peg bolt using the 1/2″ x 3″ bolt and spacer tube (both supplied). Tighten the bolt making sure the foot peg folds in the proper direction. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM Note: For easier installation on models with floorboards, it will be necessary to loosen the right side floorboard. 1. Check the stock exhaust gaskets to be sure they’re in good shape. If you have any doubts as to their condition, replace them. 2. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of each heat shield. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the motorcycle. 3. Install the circlips and flanges from the stock system onto both new head pipes. 4. Install the header using the stock nuts, but leave them loose at this time. 5. Install the new mounting bracket to the frame below the right rear foot peg, using the two 3/8″x 3/4″ flange bolts (supplied), and tighten. 6. Slide the dog bone shaped nut plate under the bracket that is welded to the backside of the muffler.

SUZUKI M109 1800 cc FRONT/REAR EXHAUST / HEATSHIELD INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 15-11-2010

download
1. Remove the seat and right side fairing cover (with M109 insignia), behind the fuel tank. To remove the fairing, release the plastic peg on top by pushing the center inward and pulling the fairing upwards until the peg releases, remove the M6 button head bolt at the bottom of the fairing. Pull the fairing outward from the rear and upward near the plastic peg to release it. Once it is free from all plastic pegs pull it forward to release it from the bottom of the fuel tank. 2. Remove the right side cover above the exhaust-mounting bracket secured by one M6 button head bolt, retain bolt for later. Remove the chrome steel cover above the exhaust secured by two remaining bolts, (this chrome piece will no longer be used.) Remove the large left rear rubber grommet and flanged steel collar from this chrome piece, to do this press the steel collar out of the rubber grommet first, once the collar is removed push the rubber grommet out of the wire loop on the chrome piece, set collar and grommet aside for later use. 3. Locate the exhaust valve actuator solenoid and harness and disconnect the black 3-prong electrical connector and white 2-prong electrical connector. 4. Remove the socket head bolts securing exhaust flanges to cylinder heads, set these fasteners aside for later use in reassembly. Support the weight of the exhaust system and remove the 2, 8 mm bolts and one 8 mm nut securing the exhaust mounting bracket and exhaust assembly. Keep these fasteners for use later. Remove the stock exhaust system as one complete unit; this includes the stock exhaust bracket, headpipes and muffler, exhaust valve actuator solenoid and cables. 5. The exhaust valve actuator solenoid must now be removed from the stock exhaust-mounting bracket. To perform this, loosen the two nuts securing each cable to the exhaust valve cable-mounting tab, Position A in Figure 1. Make enough slack in the cables so that the ends of the cables’ threaded sheath may be disengaged from the end of the mounting tab. Now remove the two M6 hex head bolts securing the solenoid to the stock exhaust bracket. The stock exhaust mounting bracket, headpipes and muffler and exhaust valve solenoid cables will not be used anymore with the your new Cobra Exhaust System

V-Star 1100 And Dragstar 1100 Modification V-Star Driving/ Passing Lights Factory Chrome Light Bar Cover Installation

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. Use a rotary tool to widen the fastening area of the lower backside clips on the cover. The total width between the clips should be 4 æ inches. Trim off º inch on both inside ends of the lower backside attachment clips. Trim the clips equally. The following picture shows a modified cover. Narrow the clips on both ends to fit over the welds on the bar. The cover will not attach to the bar if the width between the clips is too narrow. If the width is too wide the cover may slide sideways on the bar. Narrow both clips equally to center the cover over the welds on the lower edge of the bar. The top of the cover is modified to allow the cover to fit over the bolts on the light bar. The top edge of the cover is filed æ inch deep and 5/8 inch wide to fit over the bolts. The back top edge is filed or ground 1/8 inch to fit over the light bar fastening bracket. Use care when filing chrome covered plastic. The following picture will help to complete this step in the modification. Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. The ends of the cover are modified to allow the cover to fit over the upward curved light bar. The upper openings on the ends of the cover that fit over the bar must be filed to enlarge the area. Grinding the cover ends will allow the cover to fit and clip onto the bar. The end openings are filed or ground at an angle to match the slope of the bar. This picture shows the outer end of the cover. The ends of this cover have been modified by enlarging the area on the upper edges to fit over the upward curving light bar. The ends must be enlarged 1/8 inch on the top edge. The cover edge can be slanted upward to match the curved bar. Modify the cover ends until it fits without the outer chrome cover touching the bar. Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. Sometimes the modified light bar cover may touch the bottom of the headlight. Modify the cover, or adjust the bar or headlight if you notice the headlight touching the bar cover. This modification makes the V-Star motorcycle with Yamaha driving lights look better. The light bar bolts are covered and the chrome cover improves the appearance of the front of your bike. Other V-Star riders will notice how nice the front of your bike looks with the chrome light bar cover installed

Incoming search terms:

Harley Davidson Sportster Straightshots HS Slip-on Exhaust system

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Loosen the heat shield clamps on both the front and rear exhaust pipes. This allows easier access to the head pipe mounting nuts. 2. Loosen, but do not remove, the two head pipe mounting nuts from each flange located at the cylinder head. 3. Remove the clamp bolt which mounts the rear head pipe to the belt drive cover bracket. 4. Loosen the clamp holding the mufflers onto the head pipes. Page 1 of 4 D480IN Rev. 1.0 Sportster Straightshots HS Slip-on Exhaust system Part #16819 U S A Congratulations, you have purchased the finest exhaust system available for your motorcycle. Your VANCE & HINES exhaust system is designed and crafted for maximum performance, a perfect fit, a great sound and unbeatable style! Please follow the installation instructions below and if you have any questions, feel free to call our technical help line (562) 926-5291. Attention Installer: (if other than owner): Please forward this instruction sheet to the purchaser of this product. These instructions contain valuable information necessary to the end user. Tools required for installation: 1/2″ combination wrench 3/8″ drive ratchet and 9″ extension 9/16″ and 1/2″ sockets 5/16″ Nutdriver/flat blade screwdriver 5. Remove the two bolts from each muffler which attach the mufflers to the mounting bar. 6. Remove the mufflers by sliding them off the head pipes. 7. Remove the clamp from the nose of each muffler (these will be re-used when installing the new mufflers). 8. Remove the gaskets from the crossover ports on the stock mufflers. Inspect the gaskets and replace if damaged or worn (H-D part #65927-00). 9. Install crossover gaskets onto mounting bar on motorcycle. VANCE & HINES EXHAUST SYSTEM INSTALLATION 1. Remove mufflers and heat shields from protective packaging. 2. Slide the nut plate inside the bracket that is welded to the backside of each muffler body and attach the muffler bodies to the mounting brackets (stamped 379-P) using four 5/16″ x 5/8″ flange head bolts (supplied). Leave them loose at this time (Figure 1). 3. Slide stock exhaust clamp onto nose of each muffler. 4. Slide mufflers onto head pipes and align crossover port with gasket on mounting bar (Figure 2). Press into place on gasket. 5. Attach the muffler brackets to the stock mounting bar using four 5/16″ x 3/4″ hex head bolts, washers, and nuts (supplied). Leave them loose at this time (Figure 3). 6. Tighten cylinder port exhaust flange nuts on front and rear cylinders. 7. Install and tighten the clamp bolt which mounts the rear head pipe to the belt drive cover bracket. 8. Align muffler and bracket so they sit level. Tighten the muffler mounting bolts and the bracket mounting bolts. 9. Tighten the clamp holding the muffler onto the head pipe.

Incoming search terms: