05 zx10r secondary butterflies removed

You search Auto repair manual PDF 05 zx10r secondary butterflies removed, if there are search results will appear below. If search results do not exist, please search by others keyword.





KAWASAKI TERYX 750 CLUTCH KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove both seats from the vehicle. Next, remove the passenger side lower body panel. There is a mixture of Philips head screws and also plastic push pin fasteners that have to be removed. 2. With the side panel off, the next item to remove is the plastic housing over the engine. These are all “push in” style plastic clips that hold it in place. Once all the pins are out, you can slide the housing off and set it aside. 3. Now the lower long plastic panel under the seat has to be removed (again mainly plastic push clips to remove) . Once they are all out, carefully remove and set aside. 4. Next, remove the fuel tank. Remove the two lines on the top of the tank. There are two straps that hold the tank in place. Remove the bolt from each strap, remove the straps, and lift the fuel tank out. 5. Now the bracket that holds the fuel pump on has to be removed. There are two bolts here to take out. Once this is done, mark the two wires to the coil and disconnect them. Set the bracket out of the way . 6. Next, the clutch cover bolts can be removed and the norkel on the housing can be loosened and i Teryx 750 Clutch Kit Instructions 5/1/09 removed. Take the clutch cove off and set out of the way. 7. With the clutch visible, you can remove the secondary clutch with a large impact wrench and metric socket . 8. Remove the bolt from the primary clutch. This is a left hand thread on the bolt. Next you will need a Kawasaki drive clutch puller (part #352251) to pop the clutch loose. If you do not have a puller, the spring cap can be removed on the vehicle and the weights can be changed out in there as well. 9. With the clutches sitting on the bench, remove the bolts that hold on the spring cover. Remove the stock spring and the stock weights 10. After reading the directions on the new weights, add the correct amount of weight to each clutch weight and install them in the clutch. Place the weight to the left side in the clutch pocket and then install the aluminum spacer. Repeat this process for the other three weights. 11. Install the new spring supplied in the kit and install the spring cover, paying close attention to the arrows on the cover. 12. Next, remove the stock spring from the secondary. It is recommended that you use the TEAM Compression tool (part # 930001) for this. With the clutch on the compression tool, compress the spring retainer down far enough to remove the snap ring with the needle-nose pliers . Slowly back off the t-handle and remove the tool.

Incoming search terms:

Triumph Bonneville America And Speedmaster The Freak Installation Instructions and Parts List

0

Filed Under (Triumph) by admin on 29-10-2010

download
INSTALLATION In order to install The Freak, the factory air-box must be removed. Because of it’s design, the factory air-box is not an item that is easily removed. There are several parts that must be removed in order to get the air-box out of the bike in one piece. We recommend using the following method to remove your air box without having to cut it into smaller pieces in order to get it out of the frame. 1. PARTS REMOVAL In order to gain access to the air-box, it is necessary to remove certain parts of the motorcycle to gain access to the air-box area of the frame. Removing the following parts should be the first steps you take. A. Seats – Remove both seats starting with the passenger pillion, if applicable. B. Side cover and grommets – Remove the plastic side cover on the right side (throttle side) of your motorcycle. This is the faux oil-tank cover that has the name of your bike on it. Underneath the side cover there are three rubber grommets (1 on the frame tab, and two on the air-box) that support the side cover. Remove the two that are on the air-box and leave the one on the frame. You will attach the two that you removed to the right side bracket in Section 4C . C. Faux air filter covers – On the right side of the bike, remove the chrome faux air filter covers, by removing the one allen head screw that holds it onto the air-box. On the left hand side (clutch side) remove the faux air filter cover in the same manner, you removed the one on the right. D. Plastic shrouds – on the left side, remove the black plastic air-box shroud, by removing the two allen head screws holding it in place. Then remove the plastic shroud covering your fuse box (this is the piece that surrounds your ignition terminal next to the battery). E. Battery – Remove the battery by unscrewing the torx-head bolt that holds the chrome bracket in place. Remove the chrome bracket and the black plastic cap. Tilt the battery out of the box with the top towards you. Disconnect both battery terminal connectors, negative (-) terminal first. Remove the battery. F. Battery box – Remove the two bolts that hold the battery box to the frame. Pull the battery box out as far as you can, then remove the the ignition terminal from the battery box, by removing the two allen screws that hold it in place from the back. Next, remove the fuse box from the battery box, by pushing it out from the back. It is not necessary to disconnect any of the wiring going to the fuse box, or the ignition terminal. G. Rear fender – Remove the rear fender, by first disconnecting the taillight wires. Follow the wires from the tail light assembly on the inside of the rear fender (left side) towards the front of the bike until you come to the box connector. Disconnect the tail light wires at this connector, being careful not to break it. Once the wiring is disconnected, remove the 6 bolts that hold it to the struts. Have someone hold the fender for you while you are removing all of the bolts so that it does not drop once the bolts are removed. Slide the fender out the rear of the bike. 2. PREPARE THE MOTORCYCLE FOR AIR-BOX REMOVAL To remove the factory air-box without damaging it, it is necessary to lift the bike. We recommend the use of a multi-position ATV/motorcycle jack with a minimum lift height of 10″. A. Setting up the lift – Place the lift under your bike and secure your bike to the lift according to the lift manufacturer’s instructions. B. Raise slightly – Lift the motorcycle to the point where the rear springs are without tension, but NOT to where the rear tire is off the ground. C. Remove the rear springs – Take off each of the rear springs by removing the the two bolts on each spring. Once all the bolts are removed gently pull the springs out off of the studs. If they do not pull off easily, you can raise or lower the bike slightly with the lift to ease tension on the spring. Remember, you should not have the rear tire off the ground at this point. The bike should only be raised enough to relax the tension in the springs. D. Remove the mufflers – Remove the mufflers by loosening the clamp at the exhaust header, and by removing the rear foot peg hangers. If the mufflers are not removed, they can become damaged by the axles in Section 2H . E. Disconnect the carburetors – With a small flathead screwdriver, pull the retainer springs out of the channel of the carburetor intake tubes (the two large black tubes coming from the air box into the back of each carburetor), and simply push them towards the air box off of the carbs

Incoming search terms:

HONDA 2002-2004 GL1800/A Linked Braking System (LBS) Proportional Control Valve (PCV) Leakage

0

Filed Under (Honda) by admin on 25-11-2010

download
1. Pump the rear brake pedal four times. •If the brake pedal feels spongy, bleed the brake system per the Service Manual. After verifying proper brake system operation, proceed to step 2 below. •If the brake pedal does not feel spongy, proceed to step 2 below. 2. Place the motorcycle on its side stand, with the handlebars in the full left position . Lock the handlebars. 3. Place a scissor jack directly under the left front brake caliper as shown in the illustration. To avoid damage to the caliper, place a protective piece of rubber (such as a piece of inner tube) between the caliper and the jack. Wind up the jack until the front wheel is approximately 15 mm off the ground. 4. Measure the distance from the secondary master cylinder piston mounting bolt to the edge of the secondary master cylinder body (rod length of the secondary master cylinder). Record this measurement . • If the measured length is 30.3 mm, replace the PCV per the Service Manual. (This length indicates the unit’s secondary master cylinder is fully stroked, which means there is no hydraulic brake pressure acting on the PCV.) After replacing the PCV, proceed to the IDENTIFICATION section of this Service Bulletin. •If the measured length is longer than 30.3 mm , proceed to step 5 below. • INSPECTION/REPAIR PROCEDURE Record this measurement. Pump the rear brake pedal four times.
GL1800/A #16 ©2005 American Honda Motor Co., Inc. – All Rights Reserved 3 of 6 FEBRUARY 2005 5. Wait 30 minutes. Do not disturb the motorcycle in any way during this time. 6. Measure the distance again from the secondary master cylinder piston mounting bolt to the edge of the secondary master cylinder body (rod length of the secondary master cylinder). •If the measurement has decreased more than 1 mm from the measurement you recorded, proceed to step 7 below. •If the measurement is within 1 mm of the measurement you recorded, the PCV is OK. Proceed to the IDENTIFICATION section of this Service Bulletin. 7. Check the PCV for leakage. • If the PCV is leaking , replace the PCV per the Service Manual. After replacing the PCV, proceed to the IDENTIFICATION section of this Service Bulletin. • If the PCV is not leaking , you must diagnose the brake system problem before proceeding. After you have diagnosed and repaired the brake system, proceed to the IDENTIFICATION section of this Service Bulletin. NOTE: Any brake system problem not related to the PCV that is found while performing this Service Bulletin is not covered by this Safety Recall. If the motorcycle’s original factory warranty is still in effect or under HPP, file a normal warranty claim. If the unit is outside its factory warranty period or HPP coverage, contact TechLine for goodwill consideration. 8. Verify proper front and rear brake operation by pumping the front brake lever and rear brake pedal before riding the motorcycle

Incoming search terms:

2004 Kawasaki ZX10R Power Commander Installation Instructions

0

Filed Under (Kawasaki) by admin on 08-05-2012

download
Remove the main seat and the passenger seat 2. Remove the tail cover by removing the two bolts. 3 Place the Power Commander in the tail section and route the wiring harness on the inside of the tail section towards the front of the bike (Fig. A). 4. Remove the fuel tank. 5. Remove the air box lid by removing the 8 screws around the outer edge (Fig. B). 6. Remove the bolts shown in Fig. C. This will allow you to remove the air box. Fig. A Fig. B Fig. C i212-411 2004-2005 Kawasaki ZX10R – PCIII USB – 2 i212-411 www.powercommander.com Remove these bolts Remove screws Remove bolts 7. Locate the Throttle Position Sensor connector. This connector is located above the left hand side of the engine. This is a white 3 pin connector. Unplug this connector (Fig. D). 8. Plug the white connectors from the PCIII in-line of the stock TPS connector (Fig. E). 9. Locate the fuel rail connector behind the injector bodies (Fig. F). This connector is brown in color

Incoming search terms:

2004 CM And King secondary shaft bearing retainer

0

Filed Under (Cobra) by admin on 10-11-2010

download
There is a slim chance (but possible none the less) that the secondary shaft bearing retainer (screw) can back out of it’s intended position. If this retainer comes out of position it can cause an immediate stop to the motorcycle and has to potential to cause substantial damage to the engine. The early button head screw (with high strength thread locking agent) has been replaced with a black oxide bolt, lock washer, and high strength thread locking agent.

1982 Kawasaki KZ550C Electric Motorcycle Conversion Notes

0

Filed Under (Kawasaki) by admin on 03-12-2010

download
Starting point: • 1982 Kawasaki KZ550C that I found in an alley near my house. Frame rust sanded and repainted. • Rebuilt front suspension ($25 for front fork oil seals, 1 weekend for repair) • Need-to-be-rebuilt front brake caliper • Need-to-be-replaced front master brake cylinder (expected ~$80) • Need-to-be-refurbished electrical wiring system and 12V battery • Working rear brake • Flat rear tire, patched with fix-a-flat (temporary repair), 77″ circumference. • In-tact 530 size 62″ chain with 36 tooth driven sprocket • Miscellaneous spare parts from 1978 Kawasaki KZ450, most of which fit on the 1982 frame, including an ignition switch and key. I started with a chassis I found in an alley near my house. It was in rough shape and needed some refurbishment before I could start the conversion. Most of refurbishment steps are listed above in bullets. In addition to the repainting and repair of important aspects of the bike, I also needed to remove the IC engine components and the grease caked on from years of IC use. The Clymer manual for this bike was helpful in this process, which was about $18 from [13]. Steps for removing the engine were as follows. I removed the seat and the gas tank. I removed the electrical system wiring and 12V battery holder. I then removed the carburetors (which took a lot of pushing and shoving) and air filter box. I then removed the drive socket cover and removed the drive socket from the engine drive shaft. This allowed me to slip the chain off of the drive socket after loosening the rear wheel to put slack into the chain. I slipped the chain off and let it rest on the rear wheel swing arm and drained the old motor oil. I then removed all of the engine mounting bolts and pushed the entire engine out of the right side of the bike. This took a lot of effort but it is possible to remove the engine without removing the piston heads as recommended in the Clymer manual. The engine weights about 60-70 lbs, so it was possible to handle with one person. I suggest using a flat car jack to help with engine removal. I will eventually sell the IC parts through Ebay

Incoming search terms:

Kawasaki ZX10R 2008 Frame Slider Installation And Removal Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
installation Steps: 1. Remove right side bolt. Mount right side puck with (99-HB-SH10125060) Socket Cap 10 X 1.25 X 60 Main Engine Stud and torque down. 2. Remove left side mid panel. 3. Locate the left side engine stud and remove bolt. 4. Some photos in this section are used for illustration examples only. It is up to you how you decide to cut your motorcycles bodywork to accept the frame slider there are many different ways customers go through this process. Shogun is not responsible for any part of your motorcycle for any reason. Precisely measure location of cut and if in doubt at any point please call us before the install process has begun. Professional installation is recommended. Always use proper safety measures during the install of this product. Do not try to install this product without proper tools, recently calibrated torque wrench, correct torque specifications from factory service manual, safety goggles and gloves. 5. Body Prep. Use masking tape to completely mask off the area on the body where you will be working. We usually will tape off approximately 6 to 8 inches around the though hole area and any other edges that could get bumped or scratched while working. Tip: In some locations you may want to double up the thickness of the masking take to give extra protection

Kawasaki ZX10R Muffler Bracket Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the 8mm bolt that secures the mounting strap to the muffler. 2. Remove the two 8mm bolts that secure the existing muffler bracket to the bikes sub-frame. 3. Install the new bracket to the sub frame with the 8X20 socket capscrews included in the kit. Place a small amount of Loctite on the threads of the screws before assembly. 4. Mount the lower part of the bracket to the muffler strap with the existing hardware. 5. Adjust the muffler strap as needed and tighten the lower 8mm bolt. 6. Double check all your work before riding.

HARLEY DAVIDSON SECONDARY BELT EMERGENCY KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
The 40101-80 kit, with a 126 tooth belt, fits: •1980-1986 FXB and 1984-1986 FXWG models This kit may also be used on 1989-1992 international Softail models with a 127 tooth belt. The 40171-97 kit, with a 130 tooth belt, fits: •1995 and later domestic Softail models •1994 and later international Softail models •1994 and later international Dyna models The 40109-86 kit, with a 132 tooth belt, fits •1986-1992 and 1994 domestic Softail models •1989-1993 international FLT and FXR models This kit may also be used on the following models with 133 tooth belts: •1991 and later domestic Dyna models •1991-1992 international Dyna models •1994-1995 international FLT models The 40100-85 kit, with a 136 tooth belt, fits: •1985-1994 domestic FXR models •1985-1996 domestic FLT models •1996 international FLT models The 40112-97 kit, with a 139 tooth belt fits •1997 FLT models Installation 1. Put transmission in ‘Neutral’. 2. Loosen rear axle nut. Loosen rear axle adjuster nut on each side of motorcycle, and move rear wheel to full forward position. 3. Remove the damaged/broken belt. 4. Inspect sprockets and belt guard for damage and/or debris. Remove any debris. If sprockets and belt guard are not damaged, proceed with the installation. 5. See Figure 1. Remove belt guard. 6. See Figure 2. Install feeder strip on emergency belt. Feed strip around transmission sprocket in a counterclockwise direction over frame cross support.

Incoming search terms:

HARLEY DAVIDSON NARROW CHROME DIRECTIONAL BAR INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
This kit is designed for installation on 1986 and later FLST®, FLSTC®, FLSTN®and 1991 and later Touring models. (Except 2004 and later FLHRS®and FLTR®) NOTE: Will not fit when equipped with Flat Lens Turn Signal Module (Part Number 91699-99A). Installation 1. Disconnect turn signal wires. For 1999 and later models: See Figure 1. Remove taillight cover and disconnect turn signal wires at connectors shown in illustration. For 1998 and earlier models: Disconnect turn signal wires at connectors located in directional bar. On 1994 and later models there are two wires for each turn signal lamp. Earlier models have only 1 wire per lamp. 2. Remove existing directional bar from motorcycle and save hardware for re-installation. If the turn signal connector is too large to be removed from the directional bar, remove the wires from the connector as follows: Bend back the connector latches on the sides of the connector slightly to free the secondary lock. Rotate the secondary lock outward on hinge to access terminals in chambers of connector housing. With a paper clip sharpened to a chisel point, insert the paper clip into the connector housing cavity until it stops. Pivot the end of the paper clip and gently tug on the wire to pull the terminal from the cavity. Do not tug on the wire until the tang that holds the terminal in the cavity is released. Take your time, a few tries may be required before you develop a feel for releasing the terminal from the connector. 3. Remove screws that mount turn signals lamps to existing directional bar. Remove lamps and turn signal wires (with their attached connector halves) from existing bar. 4. Position directional bar in mounting location at rear fender and secure bar to motorcycle using original hardware removed in step 2. Route turn signal wires from motorcycle back into directional bar, or up to taillamp (if 1999 and later model) and mate connectors. If the wires were removed from the connector in step 2, insert the terminal ends of the wires into the connector until they snap in place, then mate connector halves.

Incoming search terms: