06 harley ultra classic motor mounts and adjustment

You search Auto repair manual PDF 06 harley ultra classic motor mounts and adjustment, if there are search results will appear below. If search results do not exist, please search by others keyword.



  06 harley ultra classic motor mounts and adjustment Direct Download speed 5282 Kb/s

  06 harley ultra classic motor mounts and adjustment Full Version speed 6162 Kb/s



HARLEY DAVIDSON ULTRA CLASSIC AND ELECTRA GLIDE CLASSIC TOUR PACK ADJUSTMENT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 23-04-2012

download
1. Open the Tour Pack and remove all of the contents. 2. Remove map bag and inner pack liner. Pack liner comes out quite easily once map bag is removed. 3. Remove the 4 bolts inside the tour pack that are located on top of the metal support plate that hold the tour pack to the luggage rack. Have your assistant hold the pack in place before removing the last bolt. 4. Gently tip the tour pack forward to expose the supporting luggage rack under the pack. 5. While your assistant holds the pack up, place the two adjusting bars on top of the supporting luggage rack. Use the 4 flat head screws supplied with the kit to mount the bars snugly to the support rack (see fig. 1). 6. Reposition the tour pack over the threaded holes in the adjusting bars at the 2″ or 3″ position and bolt it in place snugly (see fig. 2). 7. Replace the trunk liner and map case and the installation is complete

Incoming search terms:

HARLEY DAVIDSON BLACK ENGINE GUARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL NOTE This Instruction Sheet covers several different Harley-Davidson models and years. Be sure to locate and follow the procedures that apply to the motorcycle receiving the new guard. For Models without Lower Fairings 1. Proceed to For All Models section. For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Remove the lower fairings following the instructions in the appropriate Service Manual. 2. When the lower fairings have been removed, proceed to For All Models section. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley-Davidson Genuine Motor Accessory Lower Fairings 1. See Figure 1. Remove the two black screws (1) that attach the fairing cap (2) to the lower fairing (5). Remove the cap. Set the parts aside for re-installation. 2. Remove the screw (7), rubber washer (8) and locknut (10) and the clamp (9) that attaches the bottom of the lower fairing to the engine guard and set aside. 3. Remove the two locknuts (3), U-bolt (6) and U-bolt retainer (4). 4. Remove the lower fairing by sliding it out from behind the engine guard. 5. Repeat Steps 1 through 4 for the opposite side. 6. Proceed to For All Models section. For Model FLTR/I (Road Glide) with Harley-Davidson Genuine Motor Accessory Lower Fairings Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery, negative (-) battery cable first, following the instructions in the appropriate Service Manual. 2. Remove the seat following the instructions in the appropriate Service Manual. 3. Remove the cable strap holding the clutch cable to the engine guard. 4. See Figure 2. Remove the TORX screw (8), rubber washer (9) and locknut (11) and the clamp (10) that attaches the bottom of the lower fairing (4) to the engine guard and set aside INSTALLATION 1. Hold the engine guard in position, and loosely fasten the top of the guard with the new hex socket screw and flat washer from the kit. 2. Install the bottom brackets to the motorcycle frame with the two new TORX screws and locknuts. 3. Tighten all three screws to 15-20 ft-lbs (20.3-27.1 Nm) . For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Install the lower fairings following the instructions in the appropriate Service Manual. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley- Davidson Genuine Motor Accessory Lower Fairings 1. Carefully place one lower fairing in position from behind the engine guard. 2. See Figure 1. Install the lower fairing to the top of the new engine guard with the U-bolt (6) from the back, through the holes at the top of the fairing. Install the retainer (4) in position on the U-bolt and secure to the engine guard with the two locknuts (3). Do not tighten the locknuts at this time. 3. Attach the bottom of the fairing to the engine guard with the clamp (9) removed earlier. Install the clamp around the engine guard in the direction shown, with the tabs toward the rear of the vehicle and the flat side of the clamp against the lower fairing. Insert the screw (7) through the lower fairing, rubber washer (8) and clamp (9). Secure the assembly with the locknut (10). Tighten to 12 ft-lbs (16.3 Nm) .

Incoming search terms:

Harley Davidson FL series Electra Glide, Ultra Classic, Road King, Road Glide Left and Right Mounting Plate Installation Installation Manual

0

Filed Under (Harley Davidson) by admin on 25-02-2012

download
Remove existing control arm end cap and grind the outside flush. See picture below for reference. The swing arm will drop if both sides are removed at the same time. To ease installation, complete one side before starting on the other. Note: there is a left and right. Left and right end caps shown. 2. Install mounting plate assembly 10002351 on top of the end cap using 7/16″ hex head bolt and lock washer in the bottom hole. Use the 7/16″ counter sink bolt in the top hole. Make sure the end cap is seated properly. The end cap notch should fit into the recess on the frame. The pivot arm assembly is shipped on mounting plate assembly; you may remove the pivot arm to make installation easier. 3. Snug up the bolts evenly, make sure the end caps are not crooked in relation to the frame. Tighten both bolts to 25 ft lbs. (Further tightening will be required after the toe in is set). 4. If you removed the left hand pivot arm assembly, remount it now, 10002575-A (pg 20) with seal, bearings (2), washer, nut, cotter pin and dust cover. 5. Repeat for right hand side. 5 Toe In Adjustment Adjustment made with the mounting plates, bolts, pivot arms, and hubs (without wheels and tires) in place

Incoming search terms:

REKLUSE MOTOR SPORTS Pro Start Clutch Harley-Davidson OWNER'S MANUAL

0

Filed Under (Harley Davidson) by admin on 24-11-2010

download
REAK-IN PERIOD The ProStart clutch requires a short break-in period. During the break-in period, the ProStart should not be operated at steady engine speeds above 3000 RPMs for more than 10 minutes. Breaking-in the ProStart clutch equires start and stop cycles. Riding the ProStart clutch in stop-and-go city traffic for one hour will provide sufficient break-in. If you would like to accelerate the break-in period, find an empty parking lot with ample room and no other traffic. From a stop, bring the motorcycle to 20 miles per hour and then back to a stop. Repeat this process at least 20 times. MAINTENANCE Proper maintenance is important to ensure the longevity of the Rekluse ProStart clutch and the rest of the stock clutch components in your Harley- Davidson Motorcycle. Refer to your owner’s manual for proper primary chaincase oil levels and oil type. Rekluse recommends the use of Harley- Davidson Primary Chaincase lubricant with the Rekluse ProStart clutch. Do not use oils designed for use as automotive engine oil in your Primary Chaincase. If Harley-Davidson Primary Chaincase lubricant is not readily available, a premium-quality Diesel engine oil, such as Shell Rotella T, that does not contain friction modifiers may be substituted. Inspection and adjustment of the Rekluse ProStart clutch should only be performed by a service center trained in Harley-Davidson and Rekluse ProStart repair and maintenance. The Rekluse ProStart clutch should be inspected for adjustment after 1,000 miles of operation. Thereafter, inspection for adjustment should be performed at 5,000 mile intervals

Harley-Davidson FL Models (1993-2009) HARLEY PASSENGER FLOORBOARD COMFORT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-04-2012

download
1. Using your 5/16″ allen wrench, unscrew the Cap head allen bolts attaching the stock passenger floorboard mount to the frame and remove the assembly. You will reinstall this assembly once the mounts have been installed. STOCK MOUNT FEATURES: Notice the floorboard mount has a locating pin that protrudes from the rear surface. This pin is what keeps the mount from swiveling on the frame. The frame has three threaded holes and one unthreaded hole on each side. These holes provide the three different floorboard heights the bike offers stock. HEIGHT POSITIONS: The Comfort Kit mounts provide you the ability to raise the stock floorboards height 1-1/4″ or 2″ higher than the highest stock position. This is accomplished by attaching the mounts to the specific combinations of the threaded holes on the frame. POSITION #1 – Raises the floorboards 2″ by attaching the mounts to the #1 & #2 threaded holes from the top. NOTE: You must use the rectangular spacer block in order to use the 2″ rise position in order to clear the right exhaust pipe. POSITION #2 – Raises the height 1-1/4″ by attaching the mounts to the #2 & #3 thread holes from the top. TILTING: You will notice one threaded and one unthreaded hole towards the top of each mount and directly between these holes is an engraved L & R. These mounts are Left and Right side specific. The locating pin mentioned in the stock mount features paragraph inserts into the unthreaded hole and locks the floorboard into its tilted position.

2010 Harley-Davidson FLHR Road King front and rear 4-piston braking system Installation

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
in Vivid Black with blue and silver pinstripes, six-speed. Air-cooled, Twin Cam 96™ engine with Electronic Sequential Port Fuel Injection (ESPFI), ABS, security system, cast wheels with independent front and rear 4-piston braking system. Motorcycle generously donated by Harley-Davidson Motor Company Police & Fleet Sales. MSRP excludes all taxes title/documentary fees, registration, tags, dealer prep, labor and installation charges, insurance, optional equipment and accessories, certificate of compliance or non-compliance fees, and finance charges. Delivery must be coordinated through Rockville Harley-Davidson by November 30, 2010. Winner is responsible for any applicable fees above. 6,000 tickets printed. Odds of winning are 1:6,000. Ticket holder need not be present to win. Licensed by the D.C. Lottery and Charitable Games Control Board. Must be 18 years or older to win. No substitutes, return for cash, or other models. As per IRS tax code, amounts paid for chances in a raffle do not qualify as a deductible charitable contribution. Taxes on prizes are the responsibility of the winner. Harley-Davidson is proud to be a sponsor of the National Law Enforcement Officers Memorial Fund. Harley-Davidson Motor Company is a prize provider only, and Harley-Davidson, Inc., and Harley-Davidson Motor Company have no responsibility regarding conduct or administration of the raffle.

Incoming search terms:

Harley Davidson Installing The Ride Time Ultra Progressive Tour Pak LED Tail Lights

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
Remove the light bulbs from the tail light housing by depressing the tab on the bulb socket assembly and turning counter clockwise. Remove the bulb from the bulb socket. 2. Remove the lenses from the warp-around light fixture. These lens are held in place by a non-hardening black sealant. In addition, there are three plastic alignment tabs on the lens body that clip into the lens frame. To remove the lens, insert the supplied push Stick through the hole in the back of the light bulb housing and gently but firmly push the lens outward. This action places a stress on the alignment tabs. 3 . Using a flat blade screw driver, pry the lens away from the frame at the top, side, and bottom to release the lens alignment tabs. Go back to step 2, and use the plastic tube to push the lens outward. It may be necessary to repeat the prying process and pushing process several times to remove the lens. Note: Some users have found it useful to heat the lens area with a hair dryer to soften the adhesive. Included in this kit are: Left and Right LED modules, 1 RTQC Quick Connect Accessory Cable , 2 RTV application sticks, 1 push stick, Approximately 3 inches of shrink tube, and 1 copy of instructions. Required for installation, but not included are: A tube of Permatex RTV (available at Wal-Mart), 1/8 inch drill bit, a drill, small flat blade screwdriver, other hand tools. Window/ body sealer if required to reseat lenses can be obtained at your local glass shop. Tour Pak, Harley Davidson, Electraglide, Raod King, and Ultraglide are registered trade marks of Harley David- son. Harley Davidson does not make or endorse the use of these lights. 4. When the lens begins to emerge from the frame, grasp it at the top and bottom and pull the lens from the housing using a up and down motion. Set the lens aside . Avoid having the sealant contact other surfaces. In most cases, the lens can be reinstalled without adding additional sealant . Note: Do not use RTV to reset the lens. If sealant is needed obtain a non-hardening body/windshield sealant from your local glass shop. 6. When you are comfortable with the location of the circuit board, drill a 1/8 inch hole in the back of the light housing. This hole will be used to bring the turn signal wire from the LED module into the Tour Pak. 7. Using the supplied stick, spread a thin layer of Permatex clear RTV silicone seal along the area where the circuit board will be located. Apply a similar layer to the top of the light housing. Route the turn signal wire through the 1/8″ hole and position the circuit board in the housing. Allow the RTV to cure. 5. Test fit the LED light board in the light housing.

HARLEY DAVIDSON ADVANCED AUDIO XM SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
this kit fits 2006 and later FLHT (Electra Glide®), FLHTC (Electra Glide Classic), FLHTCU (Ultra Classic® Electra Glide), FLHX (Street GlideTM) and FLTR (Road Glide®) model motor- cycles. XM satellite radio is available within the continental United States. It is not available in Alaska or Hawaii. Additional Parts Required FLHT models will require prior installation of an Advanced Audio AM/ FM/ CD Radio Kit (Part Number 76412-06) and an AM/ FM Antenna Kit (Part Number 76325-06 or 76317-06). Unless one has already been fitted as part of another Advanced Audio kit installation: FLHT, FLHTC, and FLHX models will require the additional purchase of a Non-Ultra Overlay Harness (Part Number 70169- 06) and a left-hand Antenna Bracket (Part Number 76456-06). FLHTCU models will require the additional purchase of an Ultra Overlay Harness (Part Number 70164-06) and a left-hand Antenna Bracket (Part Number 76456-06). FLTR models will require the additional purchase of a Non- Ultra Overlay Harness (Part Number 70169-06) and an Antenna Bracket (Part Number 76316-06). If two modules are already installed on top of the radio, two Dual-LockTM mounts, Part Number 76434-06, will be needed. These items are available from a Harley-Davidson Dealer INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. 2. Remove the outer fairing and windshield. Refer to OUTER FAIRING/ WINDSHIELD REMOVAL in the Service Manual. NOTE If another module has been installed in the location reserved for the XM radio module, relocate that module per the instructions supplied with that kit

2000 Harley-Davidson FLHRCI Road King Classic

0

Filed Under (Harley Davidson) by admin on 03-11-2010

download
the Road King® Classic is a motorcycle with enough traditional styling to drop jaws throughout the continent. The Road King® Classic boasts laced wheels, fat white-walls and gorgeous leather saddlebags with hard inserts so they keep their shape across the long miles. Slightly narrower new handlebars provide improved ergonomics. Fender tips, tank and seat valance all boast a metal emblem. The model is available with a fuel-injected, chrome-and-black Harley- Davidson® Twin Cam 88 engine. Specifications: Engine Type: 1449 cc, 4-Stroke, Air Cooled, V-Twin Engine Bore and Stroke: 95.3 mm x 101.6 mm Valves 2 valves/cylinder Claimed Horsepower: 67 hp (50 kW) @ 5200 rpm Maximum Torque: 110 Nm (81.1 ft. lbs) @ 3100 rpm Transmission type: 5 speed Final Drive: Belt Tire – Front: 130/90-16 Tire – Rear: 130/90-16 Brakes – Front: dual 292 mm discs with 4-piston calipers Brakes – Rear: single 292 mm disc with 4-piston calipers

1995 Camry WIPER MOTOR CIRCUIT BREAKER INSPECTION PROCEDURE

0

Filed Under (Toyota Manuals) by admin on 15-10-2011

download
INSPECTION PROCEDURE: Inspect the Wiper Fuse. Verify there is power and ground to the Wiper Motor on all speeds (including “Intermittent” or “Mist” if applicable). After verifying power and ground to the Wiper Motor, follow the procedure below to prevent unnecessary Wiper Motor replacement because of a temporary open in the Wiper Motor Circuit Breaker. 1) Disconnect the Wiper Motor Harness Connector. 2) Wait (10) minutes before checking continuity. 3) Check the continuity of the motor with an ohmmeter. REPRESENTATIVE CHECKING PROCEDURE: NOTE: Continuity check can be performed between either the low speed or high speed terminal and the ground terminal of the wiper motor. The standard resistance of a good wiper motor is approximately 1.5 to 4.5 ohm

Incoming search terms:

Incoming search terms: