1976 triumph bonneville 750 wiring diagram for motorcycle

You search Auto repair manual PDF 1976 triumph bonneville 750 wiring diagram for motorcycle, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1976 triumph bonneville 750 wiring diagram for motorcycle Direct Download speed 5282 Kb/s

  1976 triumph bonneville 750 wiring diagram for motorcycle Full Version speed 6162 Kb/s



TRIUMPH BONNEVILLE, T-100 BONNEVILLE AND THRUXTON 900 CARBURETOR KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 28-10-2010

download
REAR WHEEL REMOVAL- PAGE 14-14 Triumph Motorcycle Service Manual 1.) Support motorcycle on center stand or center lift so rear wheel is suspended and there is clearance for removal. Use tie downs. 2.) If both wheels are raised chock the front wheel to prevent any weight shift when rear wheel is removed. 3.) Remove chain guard. 4.) Remove caliper and support so there is no strain on the brake line. 5.) Remove both silencers from exhaust headers. 6.) Remove axle nut and washer—support or chock rear wheel—and slide out axle. 7.) Disengage chain from sprocket and hang over swing—use soft cloth to protect swing arm from scratches that will occur if you do not cover. 8.) Lower wheel to the ground and collect spacer and caliper support arm and all fasteners for re-assembly. B.) REMOVE SEAT PAGE 15-9 Triumph Motorcycle Service Manual 1.) Remove the 2 allen-screws from rear seat section. 2.) Lift seat from the rear and slide backwards to disengage tongue– collect all fasteners for re-assembly. C.) REMOVE REAR MUD GUARD PAGE 15-13 Triumph Motorcycle Service Manual 1.) Disconnect battery and remove from motorcycle. 2.) Disconnect electrical connectors on the underside of the mudguard. 3.) Support fender from beneath and remove the 4 Torx head screws– collect all fasteners for re-assembly. D.) REMOVE FUEL TANK PAGE 9-10 Triumph Motorcycle Service Manual 1.) Turn off fuel tap. 2.) Remove fuel line at the tap connection. 3.) Remove both rear tank-mounting bolts. 4.) With assistance from another set of hands support tank at the rear and lift so that the breather line is visible on the right side of the underside of tank—remove and plug line. 5.) With tank raised and supported at the rear slide backwards— disengaging it from the front mounting rubbers—set tank aside in a safe place to prevent any damage to the painted surface

2002-2004 TRIUMPH BONNEVILLE AMERICA/ SPEEDMASTER CARBURETOR KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 28-10-2010

download
A.) REAR WHEEL REMOVAL- PAGE 14-16 Triumph Motorcycle Service Manual 1.) Support motorcycle on center stand or center lift so rear wheel is suspended and there is clearance for removal. Use tie downs. 2.) If both wheels are raised chock the front wheel to prevent any weight shift when rear wheel is removed. 3.) Remove chain guard. 4.) Remove caliper and support so there is no strain on the brake line. 5.) Remove both silencers from exhaust headers. 6.) Remove axle nut and washer—support or chock rear wheel—and slide out axle. 7.) Disengage chain from sprocket and hang over swing—use soft cloth to protect swing arm from scratches that will occur if you do not cover. 8.) Lower wheel to the ground and collect spacer and caliper support arm and all fasteners for re-assembly. B.) REMOVE SEAT PAGE 15-9 Triumph Motorcycle Service Manual 1.) Remove the 12 mm bolt from rear seat section—if you have a pillion pad remove it first by removing the 8 mm bolt, slide forward and lift free of seat catch. Take a position where you can see what you are doing or you will scratch your painted surface. 2.) Lift seat from the rear and slide backwards to disengage tongue– collect all fasteners for re-assembly. C.) REMOVE REAR MUD GUARD PAGE 15-14 Triumph Motorcycle Service Manual 1.) Disconnect battery and remove from motorcycle. 2.) Disconnect electrical connectors on the underside of the mudguard. 3.) Support fender from beneath and remove the 4 side allen head mount bolts and 2 12mm hex head top front mount bolts– collect all fasteners for re-assembly. D.) REMOVE FUEL TANK PAGE 9-11 Triumph Motorcycle Service Manual 1.) Turn off fuel tap. 2.) Remove fuel line at the tap connection. 3.) Remove the 12mm rear tank-mounting bolt. 4.) With assistance from another set of hands support tank at the rear and lift so that the breather line is visible on the right side of the underside of tank—remove and plug line. 5.) With tank raised and supported at the rear slide backwards— disengaging it from the front mounting rubbers—set tank aside in a safe place to prevent any damage to the painted surface. E.) REMOVE SIDE COVERS PAGE 15-10 and 9-15 Triumph Motorcycle Service Manual 1.) Loosen and remove left side cover screws on the air filter facade— lift slightly to disengage top mounts and remove—set aside in a safe place to prevent damage to painted surface. 2.) On right side cover simply and gently pull bayonet fittings from rubber slip mounts. 3.) Secure these rubber mounts and remove for later re-assembly with the Bonneville Performance brackets.

Triumph Bonneville, Bonneville T100, Thruxton & Scrambler Dresser Rail / Sissy Bar / Grab Rail Kits Fitting Instructions

0

Filed Under (Triumph) by admin on 29-10-2010

download
1. Undo and remove the two screws and flanged sleeves (if fitted) from the rear of the riders seat. 2. Remove the seat. 3. Disconnect the battery, negative (black) lead first. 4. Locate the rear light unit wiring connector and disconnect it from the main wiring harness. 1. Rear light unit wiring connector NOTE Take care not to damage the painted finish of the mudguard. 5. Undo the four screws securing the rear mudguard to the frame, then remove the mudguard assembly from the motorcycle. 1. Rear mudguard fixings Warning Throughout this operation, ensure that the motorcycle is stabilised and adequately supported on a paddock stand to prevent risk of injury from the motorcycle falling. Warning A torque wrench of known accurate calibration must be used when fitting this accessory kit. Failure to tighten any of the fasteners to the correct torque specification may result in loss of motorcycle control and an accident. 1 1 3 of 4 6. Position the dresser rail to the frame and secure with six of the supplied M8 x 20 mm bolts (four at the rear and one on either side at the front). Tighten the bolts to 18 Nm. Scrambler only – Fit four M8 washers between the dresser rail and the rear mounting points. 1. Rear mounting points 2. M8 washer positions (Scrambler only) 1. Front mounting point (left-hand shown) 7. Ensure the rear light wiring grommet is correctly located in the front edge of the mudguard then, taking care not to damage its painted finish, position the rear mudguard to the frame. 8. Ensure the mudguard is correctly located to the rear of the airbox then secure with the original fixings tightening them to 9 Nm. 9. Ensure the wiring for the rear light unit is correctly routed then reconnect it to the main wiring harness connector. Sissy bar installation 1. Using the M8 x 20 mm bolts and spacers, loosely secure each sissy bar to the dresser rail. 1. Spacers 2. M8 x 20 mm bolts 2. Fit an end cap to each sissy bar. 3. Using the supplied M6 x 12 mm bolts and nuts, secure the backplate to the sissy bars. Ensure the badge on the backplate is facing towards the rear of the motorcycle then tighten the fixings to 8 Nm

Triumph Scrambler And Bonneville Single Seat And Rack Kit Fitting Instructions

0

Filed Under (Triumph) by admin on 29-10-2010

download
To help prevent damage to the seat and rack kit, carry out the following procedures on a soft, non-abrasive surface. cdrt 1 2 3 1
3 cowl to the seat on each side. Tighten the screws to 3 Nm. 1. Seat cowl (right-hand side shown) 2. M5 bolt and washer 7. Undo and remove the screws and flanged sleeves located at the rear of the original seat. 1. Seat screws 8. Remove the original seat. NOTE •Retain the original seat for re-use if the motorcycle is returned to original condition. 9. Fit the new seat and rack assembly using the original fixings. Locate the seat to the frame ensuring the locating tongue on the underside of the seat is positioned beneath the fuel tank bridge. Tighten the seat screws to 10 Nm. 1 2 cdrw 1 2 1 Warning The maximum load that may be carried on the luggage rack is 5 Kg (11 lbs). Incorrect loading of the luggage rack may result in an unsafe riding condition leading to loss of motorcycle control and an accident. Always ensure any loads carried are evenly distributed on both sides of the motorcycle. Ensure that the load is correctly secured such that it will not move around while the motorcycle is in motion. Check the load security regularly (though not while the motorcycle is in motion) and ensure that the load does not extend beyond the rear of the motorcycle. Never exceed the maximum vehicle loading weight of 217 Kg (477 lbs). Warning The luggage rack must not be used to carry sharp objects, or objects which extend beyond the extremities of the rack. Carriage of such items may interfere with, or distract, the rider or passenger and could affect the stability and handling of the motorcycle leading to loss of control and an acciden

HONDA GL1100 AM/FM RADIO INSTALLATION MANUAL/ WIRING DIAGRAM

0

Filed Under (Honda) by admin on 22-04-2011

download
INSTALLATION ■ Outline Procedures This section gives general information needed for mounting the individual radio components on and in the fairing. A) Fairing 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove fairing parts. 3) Drill unit mount holes. 4) Install six wire clips. 5) Install windshield on fairing before install- ing speakers. 6) Install radio indicator I on indicator panel II , then install indicator panel on fairing. 7) Install speakers III. 8) Install nutplate IV. 9) Install Power Amplifier in fairing. 10) Install radio funer VI. 11) Install the radio controller VII. 12) Install controller base panel VIII 13) Install radio switch sub-wire. 14) Connect adapter harness and wires inside fairing by working through left turn signal lens hole. B) Motorcycle frame and handlebar 1) Remove travel trunk and seat. Unscrew four shelter bolts (M6, one on each side at front and rear) to route antenna feeder. 2) Install antenna mount and antenna IX. 3) Route antenna feeder along the frame tube. 4) Install radio switch X on left handlebar lever bracket and route the wires. 3 of 11 Page 4 C) Fairing instllation 1) Install fairing on motorcycle. 2) Connect motorcycle wire harness 9-P coupler to fairing wire 9-P coupler. 3) Connect radio switch wire to switch sub- wire.4) Connect antenna feeder. 5) Confirm that radio operates properly. Reinstall parts removed in step 2 or (A) and in step 1 of (B). REWORKING ■ Remove Fairing and Fairing Parts (Fig.10) 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove right and left fairing pockets, right and left turn signal lenses, right and left nutplates, left hole cover and indi- cator base panel from fairing. (Fig.10) Fig. 10 LEI-1 NU I PLATE 4 of 11■ Reworking on Fairing — Speaker mounting holes- 1) Remove 18 mm grommet. 2) Lightly roll template so that it will follow contour of fairing snugly. 3) Position template on fairing with its upper and outer edges aligned with those offairing as indicated by arrows. 4) Attach template to fairing using adhesive tape where shown. 5) Punch mark centers of four holes with a
drift and hammer. 6) Drill 6 mm holes through marked centers. To obtain a more balanced response with richer, deeper bases, drill two 50 mm holes in the fairing so as to link the speaker box with the inside of the fairing. Fig. 11-1
—Power amplifier mounting holes- 7) Drill two 5.5 mm holes through concaves in fairing. Fig. 11-2 RIGHT HAND SHOWN, LEFT SIMILAR ADHESIVE TAPE

Related Item : yhs-fh_lsonsw (3)how to install sportster quarter fairing (2)inngt fairing removal flt (2)quarter fairing with speakers (2)www 2007 kawasaki concours fairing removal (2)1982 kawasaki kz 550-4 a/b/c wiring diagram (2)M109R Fairing with Radio (2)M109R Front Fairing replacement (1)motorcycle lower leg fairing (1)Motorcycle radio faceplates (1)