1983 yamaha venture wirin diagram

You search Auto repair manual PDF 1983 yamaha venture wirin diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1983 yamaha venture wirin diagram Direct Download speed 5282 Kb/s

  1983 yamaha venture wirin diagram Full Version speed 6162 Kb/s



1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

YAMAHA MOTOR CORPORATION, U.S.A. STREET & ENDURO MOTORCYCLE LIMITED WARRANTY

0

Filed Under (Yamaha) by admin on 27-12-2011

download
GENERALEXCLUSIONS from this warranty shall include any failures caused by: a. Competition or racing use. b. Installation of parts or accessories that are not qualitatively equivalent to genuine Yamaha parts. c. Abnormal strain, neglect, or abuse. d. Lack of proper maintenance. e. Accident or collision damage. f. Modification to original parts. g. Damage due to improper transportation. SPECIFIC EXCLUSIONS from this warranty shall include parts replaced due to normal wear or routine maintenance. THE CUSTOMER’S RESPONSIBILITY under this warranty shall be to: 1. Operate and maintain the motorcycle as specified in the appropriate Owner’s Manual. 2. Give notice to an authorized Yamaha motorcycle dealer of any and all apparent defects within ten (10) days after discovery, and make the machine available at that time for inspection and repairs at such dealer’s place of business. You may locate your nearest authorized Yamaha dealer through your local telephone directory. WARRANTY TRANSFER: To transfer any remaining warranty from the original purchaser to any subsequent purchaser, it is imperative that the machine be inspected and registered for warranty by an authorized Yamaha motorcycle dealer. In order for this warranty to remain in effect, this inspection and registration must take place within ten (10) days after transfer. Areasonable dealer imposed fee may be charged for the inspection. In no case will warranty be extended beyond the original period. EMISSIONS CONTROLSYSTEM WARRANTY Yamaha Motor Corporation, U.S.A. also warrants to the ultimate purchaser and each subsequent purchaser of each Yamaha motorcycle covered by this warranty with a displacement of 50cc or greater, that the vehicle is designed, built, and equipped so as to conform at the time of sale with all U.S. emissions standards applicable at the time of manufacture and that it is free from defects in materials and workmanship which would cause it not to meet these standards within the periods listed immediately below. Failures other than those resulting from defects in material or workmanship which arise solely as a result of owner abuse and/or lack of proper maintenance are not covered by this warranty.

Incoming search terms:

Yamaha Venture Royal Star Installation Manual

0

Filed Under (Yamaha) by admin on 09-11-2010

download
1) Secure motorcycle in an upright position. 2) Remove saddle bags 3) For hitch clearance you will need to install the enclosed muffler lowering spacers. 4) Attach forward brackets A (left) and B (right) to motorcycle rear crash bar with U-Bolts. Also attach brackets at the point where the saddle bag sub frame and rear crash bar connect using new bolt provided. 5) Attach rear brackets C (left) and D (right) to motorcycle rear frame using new bolts provided. See diagrams next page. Attach top portion first then bottom portion. 6) Attach brackets A and B to forward arms of receiver hitch. Brackets mount on BOTTOM of hitch arms. 7) Attach bottom of brackets C and D to rear of hitch. 8) Now tighten all bolts working from rear forward. 9) Replace saddle bags and double check all bolts for tightness. Hitch Diagrams InstaTrike Installation 1. Place your motorcycle on a smooth level surface and attach leveling jack stands. 2. Push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 3. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bolt. 4. Align InstaTrike wheels. (initial installation only. Check periodically and realign if necessary) 5. Bolt leanstop braces to hitch. Be certain to replace washers/spacers in the same configuration as when you removed them. 6. Remove leveling jack stands. 7. Check all bolts for tightness. 8. You are now ready for the test ride. A. Keep your feet up! B. Ride slowly in first gear until you are comfortable with the Tow-Pac system.

YAMAHA ROYAL STAR VENTURE CENTERSTAND REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 31-12-2011

download
Stand Installation. Locate the four mounting holes on the frame that correspond with the holes in the centerstand. Slide the front of the centerstand up into the frame and align the large bolt holes with those in the frame. Install the (2) 7/16″ x 1″ bolts with washers thru the frame and centerstand. Install the (2) 7/16″ nuts and make finger tight. (on California models the fuel tank vent canister must be removed and the hoses bypassed see note below) Pivot the rear of the centerstand up to align the (2) smaller holes in the stand with those in the frame. Insert a phillips screwdriver into one of the (2) remaining mounting holes and pry the other hole into alignment. Install one of the ¼” x ¾” bolt with a washer from the top down thru the frame and centerstand. Install the lock nut finger tight. Remove the screwdriver and install the remaining ¼”x¾” bolt washer and nut. Tighten the ¼ ” bolts securely 10-12 ft. lbs., then tighten the 7/16″ bolts securely 20-24 ft. lbs. 2. Stop Bumper Installation. Next install the centerstand-stop bumper and bracket onto the frame. Locate the bolt “A” in photo #1. Notice there is another 10 mm bolt just below it. Remove the lower bolt. Attach the bumper bracket to this hole using the longer bolt and washer supplied. The leg of the bracket with the bumper should face inward towards the center of the motorcycle. Adjust the height of the bracket to keep the pedal arm 3/8″ to ½” from the bottom of the exhaust pipe. Tighten securely. 3. Emissions Valve Relocation. You will notice that the right leg of the stand near the foot comes in contact with the emissions valve. The valve needs to be moved outward or to the right as you are sitting on the motorcycle approximately ¾”. This is done as follows: Remove the (2) 10 mm bolts holding the emission valve and bracket to the frame. See photo #2. With the hoses still attached pull the valve down to gain access to the (3) allen screws. Remove the (3) allen screws and (2) nuts holding the bracket to the valve, turn the bracket over and re-assemble the valve onto the bracket as shown in photo #3. Re-install the valve onto the frame. You may need to rotate the hose clamp clips out of the way and/or bend the entire valve bracket assembly outward slightly to gain clearance between the centerstand leg and foot. 4. Using Your New Centerstand. To put the motorcycle up onto the centerstand, hold the left handle bar and saddlebag guard rail. Using the ball of your right foot, lower the stand to the ground. Rock the motorcycle from side to side slightly until you feel both feet of the stand touching the ground. Now, put all of your weight on to the centerstand pedal (stand on it). Pull up and back on the grab rail using a rocking motion to rock the motorcycle up on to the stand. Remember it is a matter of using your body weight and leverage not lifting! 5. Getting the Bike Down off the Centerstand. Holding the left handle bar and saddlebag guardrail, firmly rock the motorcycle off the centerstand. You can also rock it off while sitting on the motorcycle.

Incoming search terms:

YAMAHA XVZ 1300 Royal Star/ Venture SPEEDOMETER COWL INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 07-11-2010

download
Speedometer Cowling Chrome 1 2 Alcohol Wipe 1 NOTE: Allow time for the 3M® brand quality tape to cure for 24 hours at 19-32° C before washing or waxing the motorcycle. INSTALLATION 1. Position the Speedometer Cowl in front of the Speedometer. The Cowl attaches to the Speedometer Cover, not on the rubber ring around the Speedometer. The Cowl should be symmetrically located in relation to the Speedometer, use the Speedometer markings as a reference. 2. Remove the red backing tape from the adhesive strip on the base of the Speedometer Cowl. 3. Position the Speedometer Cowl as done in step 1. Make any position adjustments now. 4. Firmly press the Speedometer Cowl in place on the Speedometer Cover. 5. Allow twenty-four hours for the adhesive to fully set before washing or waxing.

YAMAHA FZR 400 ELECTRICAL CIRCUIT DIAGRAM

0

Filed Under (Yamaha) by admin on 29-11-2010

download
CHECKING OF SWITCHES Check the switches for the continuity between the terminals to determine correct connection. Read the following for switch inspection. SWITCH CONNECTION AS SHOWN IN MANUAL The manual contains a connection chart as shown left showing the terminal connections of the switches (e.g., main switch, handlebar switch, brake switch, lighting switch, etc.) The extreme left column indicates the switch positions and the top line indicates the colors of leads connected with the terminals in the switch component. “C’&-0″ indicates the terminals between which there is a continuity of electricity; i.e., a cl.osed circuit at the respective switch positions. In this chart: “R and Br” and “L/W and L/R” are continuous with the “ON” switch position. “B and B/W” is continuous with the “OFF” switch position. “B and B/W” is continuous with the “LOCK” switch position. “B and B/W” and “R and L/R” are continuous with the “P” switch position. CHECKING SWITCH FOR TERMINAL CONNECTION Before checking the switch, refer to the connection chart as shown above and check for the correct terminal connection (closed circuit) by the color combination. To explain how to check the switch, the main switch is taken for example in the following

YAMAHA CRANKSHAFT LOWER END REMOVAL AND INSTALLATION TOOLS

0

Filed Under (Yamaha) by admin on 08-01-2012

download
90 LOWER END REMOVAL & INSTALLATION TOOLS SHOP EQUIPMENT & TOOLS 35-8399 35-8513 35-8516 35-8508 35-8504 35-8507 YAMAHA CRANKSHAFT PROTECTORS Sold each. 35-8504 YM-4063-A, XV750/920 Virago, XT550, YFP350, YFM660R Raptor 35-8399 YM-1382, XT250/XT350, RZ350, YFP350, YFZ350 35-8507 YM-33282, XV500 Virago, XZ550 Vision, XVZ12/13 Venture & Venture Royale, VMX12 V-Max 35-8508 YM-38145, XV750/XV1000 Virago YAMAHA CRANKSHAFT INSTALLATION SET Sold as a set. Consists of the following: Qt1-Installing Pot, Qt1-Pot Spacer, Qt1-Bolt. 35-8509 YU-90050 Crankshaft Installation Set OPTIONAL POT SPACERS 35-8513 YU-90070-A, XV750/920 Virago, XT550, TT600 35-8515 YU-91044, YFM350, SRX600, XT550/600 35-8516 YU-1202, SR500, TT/XT500 CRANKCASE PRESSURE TESTER An accurate method for checking possible air leaks on two-stroke engines. Complete with air pressure gauge, pump-up bulb and all fittings and adapters for single and multi-cylinder two-cycle engines. 35-5962 Crankcase Pressure Tester CRANKSHAFT INSTALLING JIG TOOL Supports and centers crankshaft webs while assembling two-stroke engine cases and rebuilding crankshafts. Prevents rod misalignment. Adjustable tang ends. 35-9804 Crankshaft Installing Jig Tool CRANKCASE SEPARATOR TOOL This tool will work on most two and four stroke engines that have a vertically split crankcase. Moveable fingers allow a multitude of bolt patterns to be used so it will work on a variety of models. Includes 6mm and 8mm mounting bolts, center pulling bolt and a three leg frame that is appropriate for many applications. 35-9642 Crankcase Separator Tool 35-9637 Replacement 6mm and 8mm mounting bolts. Each

Incoming search terms:

Yamaha 1998 XVS1100 REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 03-01-2012

download
EXPLODED DIAGRAMS To help identify parts and clarify procedure steps, there are exploded diagrams at the start of each removal and disassembly section. 1. An easy-to-see exploded diagram 4 is provided for removal and disassembly jobs. 2. Numbers 5 are given in the order of the jobs in the exploded diagram. A number that is enclosed by a circle indicates a disassembly step. 3. An explanation of jobs and notes is presented in an easy-to-read way by the use of symbol marks 6 . The meanings of the symbol marks are given on the next page. 4. A job instruction chart 7 accompanies the exploded diagram, providing the order of jobs, names of parts, notes in jobs, etc. 5. For jobs requiring more information, the step-by-step format supplements 8 are given in addition to the exploded diagram and the job instruction chart.
24 21 18 15 16 17 10 12 13 11 14 1 3 5 7 9 2 4 8 6 19 20 22 23 25 EB003000 ILLUSTRATED SYMBOLS Illustrated symbols 1 to 9 are printed on the top right of each page and indicate the subject of each chapter. 1 General information 2 Specifications 3 Periodic inspections and adjustments 4 Engine 5 Cooling system 6 Carburetion 7 Chassis 8 Electrical 9 Troubleshooting Illustrated symbols 10 to 17 are used to identify the specifications appearing in the text. 10 Can be serviced with engine mounted 11 Filling fluid 12 Lubricant 13 Special tool 14 Torque 15 Wear limit, clearance 16 Engine speed 17 Ω, V, A Illustrated symbols 18 to 23 in the exploded diagrams indicate the types of lubricants and lubrication points. 18 Apply engine oil 19 Apply gear oil 20 Apply molybdenum disulfide oil 21 Apply wheel bearing grease 22 Apply lightweight lithium-soap base grease 23 Apply molybdenum disulfide grease Illustrated symbols 24 to 25 in the exploded diagrams indicate where to apply locking agent 24 and when to install new parts 25. 24 Apply locking agent (LOCTITE) 25 Replace

Incoming search terms:

YAMAHA V-Star 1100 Motorcycle Enhancements Remote Oil Filter Installation Manual

0

Filed Under (Yamaha) by admin on 10-11-2010

download
Removing Your Old Filter and Beauty Cover In order to install the new Remote Oil Filter Kit, you’ll need to remove the stock Yamaha “beauty cover” and the old filter and filter cover. Remove the engine parts necessary to access the stock filter as outlined in the V-Star owner’s manual. The parts should come off in this order: 1. Muffler assembly 2. Front exhaust pipe 3. Rear brake reservoir cover bolt and brake cover (the reservoir should not be removed, it can remain in place and be moved aside as needed) 4. Right floorboard (this can be simply loosened, by loosening the two bolts underneath) With the above parts removed, you can remove the Allen bolts holding the beauty cover and filter cap from your engine. There are five Allen bolts holding the beauty cover (so named, because most of the cover just covers the chromed side of the engine There are five bolts holding the cover. Ignore the three on the “Yamaha” cap in the middle – these just hold the Yamaha cap to the beauty cover itself. One bolt is hidd – in this picture – just be the Yamaha ca en low p. The bottommost bolt on the beauty cover will likely leak some oil when you remove it – it holds on the inner oil filter cover. Once you remove the beauty cover, you can remove the oil filter cover, and the oil filter Keep these two “O” rings, you’ll need them for the remote kit Old oil filter. Toss it away; you’ll never need one again! Throw away the old filter, and carefully remove the orange and black “O” rings from the filter cover (see picture above). These two “O” rings will go on the new engine cap in the same order as on the old filter cover. “O” ring for bottom bolt. When the beauty cover and filter cover are removed, be sure not to lose the tiny “O” ring that the bottom bolt goes through. Preparing the Remote Oil Filter Kit Remove the orange and black “O” rings from the stock filter cover plate, and place them on the Remote Oil Filter Kit engine cap – black on the inside, orange on the outside – just like on the stock filter cover.

Incoming search terms:

YAMAHA Installing the Motorcycle Enhancements Remote Oil Filter

0

Filed Under (Yamaha) by admin on 17-01-2012

download
In order to install the new Remote Oil Filter Kit, you’ll need to remove the stock Yamaha “beauty cover” and the old filter and filter cover. Remove the engine parts necessary to access the stock filter as outlined in the V-Star owner’s manual. The parts should come off in this order: 1. Muffler assembly 2. Front exhaust pipe 3. Rear brake reservoir cover bolt and brake cover (the reservoir should not be removed, it can remain in place and be moved aside as needed) 4. Right floorboard (this can be simply loosened, by loosening the two bolts underneath) With the above parts removed, you can remove the Allen bolts holding the beauty cover and filter cap from your engine. There are five Allen bolts holding the beauty cover (so named, because most of the cover just covers the chromed side of the engine
There are five bolts holding the cover. Ignore the three on the “Yamaha” cap in the middle – these just hold the Yamaha cap to the beauty cover itself. One bolt is hidd – in this picture – just be the Yamaha ca en low p

Incoming search terms: