1984 sportster swing arm diagram

You search Auto repair manual PDF 1984 sportster swing arm diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1984 sportster swing arm diagram Direct Download speed 5282 Kb/s

  1984 sportster swing arm diagram Full Version speed 6162 Kb/s



Harley Davidson Softail Drive Side Brake System Installation Manual

0

Filed Under (Harley Davidson) by admin on 30-03-2012

download
Removing The Stock Components Although the PM Drive Side Brake System can be installed with the swing arm bolted to the frame, we recommend removing it for better access as well as repainting. Begin by removing rear wheel,stock brake components and belt guard from swing arm. Photo #1 Using supplied 3/4 x 2″bolt,position Drive Side BrakeAssembly on swing arm. Slide assembly to center position of tab and axle spans. Making sure brake mounting tabs are flush with swing arm,snug 3/4 x 2″ bolt to hold assembly and mark swing arm area to be ground Photo #2 . Remove entire assembly from swing arm and thoroughly grind paint away from marked areas Photo #3 . Photo #4 Re-mount assembly to swing arm and slide to rear-most position of both axle and brake mounting tabs. Confirm that brake tabs are flush with swing arm and parallel to each other. Snug 3/4 x 2″bolt and 5/16″socket head cap screws in tabs to hold assembly during welding process. Warning Center the motorcycle on the lift so that it will not fall while you are working on it. Photo #6 Photo #5 Photo #7 Photo #9 Welding Tabs to Swing Arm Note PM recommends all welding be done by a certified welder. Photo #5 Tack weld rear of tabs to swing arm. Avoid excessive welding near brake as- sembly as heat can mar finish. Loosen socket head cap screws and 3/4″bolt,Slide entire assembly to forward most position and re tighten bolts Photo #6 (movement should require minimal effort if tabs are aligned properly) and tack front of tabs to swing arm. Remove brake assembly from swing arm. Weld tabs to swing arm.Verify alignment of tabs, as they must remain parallel to each other. Repaint swing arm and re-install on bike to factory torque specs. Installing Brake Assembly Remove primary bracket from tower assembly (this allows bracket to be installed without having to line up caliper on disc) by removing the three 5/16″socket head cap screws (commonly called allen bolts). Photo #7 Mount rear tire and bolt pulley to rear wheel. Place disassembled bracket against pulley using smaller of two supplied spacers between bracket and pulley. Slide wheel/brake assembly into swing arm. Place large spacer on right side and slide axle in. Do not tighten axle at this point . Photo #8 Slide caliper/tower assembly over disc and install 5/16″x 1″socket head cap screw in center hole to position assembly Photo #9 . Snug, but do not tighten bolt at this point.

Incoming search terms:

1987 to Current Harley Davidson Softail (FLST Only) Motorcycle Trike Conversion removal and Installation Guide

0

Filed Under (Harley Davidson) by admin on 03-11-2010

download
Removal of Original Parts Secure and raise motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. • Seat (to be re-installed without modification). • Left and right saddle bags (if so equipped). • Left and right rear crash bars, saddlebag rails (if so equipped). • Left and right passenger foot rests (to be re-installed without modification) • Complete exhaust system (to be replaced with new system). • Rear wheel NOTE: Prior to removing rear wheel, depress foot brake and secure in down position (e.g., zip-tie to floor board). This will prevent fluid flow when rear brake caliper is removed • Remove Rear Caliper (disconnect brake line at caliper) NOTE: Cap line to prevent introduction of dust / debris into line. Remove caliper. • Rear Drive Pulley (1987-99 models to be re-installed without modification). • Rear Fender (2000 and newer models, fender mount plates to be reused). • Swing Arm NSTALLING TRIKE CONVERSION KIT 3.1 Sprockets and Drive Belts Specifications See following table for belt installation (1987-99 will use a 4 tooth longer belt) Note : See OEM manual for belt replacement procedure. Year Drive Sprocket OEM Belt New Belt / Sprocket 1987-92 70 T 132 T 136 1993-94 61 T 128 T 132 1995-99 65 T 130 T 136/70TOEM 2000-06 Champion Sprocket, 70 T 135 T Use OEM 2007 Up Champion Sprocket, 66 T Use OEM 3.2 Install Swing Arm É Noting size and location of bolts, remove Cross Assembly from Champion Swing Arm. Do not discard hardware. Figure 1 3.2.1 1987-99 Model Years • Remove bearings from OEM Swing Arm using OEM shop tools and hydraulic press. Note : Although original bearings can be re-used, it is HIGHLY recommended that NEW bearings be installed to Champion Swing Arm a. b. Press bearings into Champion Swing Arm in the same way as the OEM Swing Arm. Using OEM Spacer Tube and supplied washers (four ¾” flat washers), install Champion Swing Arm using OEM bolt, outside washers and nut. Do not torque pivot bolt nut at this time. Figure 2 Note : Insure belt path is over and under Swing Arm pivot. c. d. Replace cross assembly and hardware (previously removed in step 3.2) to Champion Swing Arm. Note that the 2 upper left hand side bolts are countersunk. Torque pivot bolt to OEM specification

TRIUMPH ROCKET III SWING ARM COVER INSTALLION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-01-2011

download
1. Locate and remove the 6mm screw which secures the rear brake hose clip to the top of the swing arm (just in front of the lower right shock absorbers mounting point. 2. Notice the double faced adhesive tape on the inside of the cover and where it will contact the swing arm when installed, clean this area with rubbing alcohol and remove the backing from the adhesive tape on the inside of the cover. 3. Place the º” washer provided on the top of the swing arm over the brake hose clip mounting hole. Starting at the rear of the swing arm slide the cover carefully into place and align the small hole in the top of the cover with the washer and the threaded hole. Place the screw thru the hose clip then the cover and finally the washer, next thread the screw into the hole finger tight only. 4. Press the front area of the cover with the adhesive tape firmly into place. Tighten the 6mm brake hose clip screw securely.

TRIUMPH ROCKET III SWING ARM COVER INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 28-12-2010

download
1. Locate and remove the 6mm screw which secures the rear brake hose clip to the top of the swing arm (just in front of the lower right shock absorbers mounting point. 2. Notice the double faced adhesive tape on the inside of the cover and where it will contact the swing arm when installed, clean this area with rubbing alcohol and remove the backing from the adhesive tape on the inside of the cover. 3. Place the ¼” washer provided on the top of the swing arm over the brake hose clip mounting hole. Starting at the rear of the swing arm slide the cover carefully into place and align the small hole in the top of the cover with the washer and the threaded hole. Place the screw thru the hose clip then the cover and finally the washer, next thread the screw into the hole finger tight only. 4. Press the front area of the cover with the adhesive tape firmly into place. Tighten the 6mm brake hose clip screw securely.

INSTRUCTIONS ON HOW TO R & R YOUR Swingarm

0

Filed Under (Tips and Review) by admin on 12-12-2010

download
• Upgrade Your Pre- 2002 FL Or FXR Rear Fork & Get Rid Of The Crappy & Dangerous (Cleve Blocks) & Replace Them With A Stable System. • R & R your Swing Arm, Belt Drive, Swing Arm Pivot Shaft, and Rear Wheel. The paragraphs below are a photo journey into the replacement of a FL or FXR swing arm. To upgrade the pre 2002 FL, here is a How-To on cheaply replacing the poor parts Harley stuck you with. Now – Let’s Get Er’ Done • Pre- 2002 had weak swing arms and are known to fail. The cleve blocks are the cause of “Rear Steer” or “Rear Fork Deflection”. Harley came up with a patch in 2002, using bearings. Because the pre 2002 transmissions have a 5/8″ mounting hole for the 5/8″ swing arm pivot shaft, a conversion unit has been made. No transmission removal for boring is necessary. Under no circumstances, do I recommend drilling out the transmission case with a hand drill. The drill will “wander” (drift)! • Solution: Go to either a trike shop/manufacturer, e-Bay, or shop and buy a new style swingarm. Harley made an additional upgrade in 2007, try and buy this type 2007 & above). If upgrading to a 2008, Harley use 25mm (smaller than 1″) axles & wheel bearings, you will have to use 25mm bearings. With that said, let’s get on with it. • In the case of a 2007 swingarm; buy and do not pay over $40 for the swing arm and axle. You must use the corresponding axle as a ¾” axle set-up is different (along with wheel bearings & spacers). You positively can not use a pre -2002 HD stock wheel because the wheel bearing spacer will fit into the wheel. Buy 2002 & above style wheels as they (9 spoke) are cheep. • You are going to have to either bore out your stock rear caliper bracket or better still, upgrade your whole rear brake to the new model & sell yours on e-Bay. • I recommend doing the following before hand and have it ready for installation; Remove bearings et al. from the 2002 & later swing arm via press. Bike Work: • Jack up your bike using a center jack. Secure the bike so it will not fall over. You can also use a motorcycle jack. I use a motorcycle dolly

HARLEY DAVIDSON Softail Big Shots Staggered Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 20-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. If equipped, loosen the floor boards to gain clearance for exhaust removal and installation. 2. Loosen heat shield clamps on both the front and rear head pipes. 3. If equipped, loosen crossover pipe clamp, located between front and rear head pipes. 4. Remove two cylinder exhaust port flange nuts from each head pipe, located at the cylinder head. 5. Remove the bolts that attach mufflers to the frame. 6. Remove the complete exhaust system and set aside. Assistance may be required. 7. Remove stock mounting bars and brackets. 8. On models equipped with upper mounting bar attached at swing arm pivot bolt, go to step 9. If upper mounting bar is attached with two torx bolts (not swing arm bolt) go to step 10. 9. Remove right side 1/4″-20 bolt which holds lower fender in place. The fender will flex outwards allowing removal of right passenger foot peg bolt. Park the motorcycle on its side stand. Position a floor jack under right hand frame tube of the motorcycle below swing arm pivot bolt. Raise jack just enough to take the weight off swing arm pivot bolt. Remove swing arm pivot bolt and stock upper mounting bar. Replace swing arm pivot bolt and torque to 120 ft. lbs. Reinstall passenger foot peg using 1/2″-20 x 3″ bolt and 1 5/8″ long spacer (supplied). Reinstall 1/4″-20 fender bolt. 10. Using a T50 torx driver, remove the three mounting bolts and mounting bar. (Two of the bolts are visible, the third also attaches right hand passenger foot peg pivot and is accessed by removing foot peg. Reinstall foot peg using 3/8″x 2-1/2″ Allen bolt and 3/4″ long spacer (supplied). 11. Carefully remove exhaust port flanges and circlips from the stock exhaust system using snapring pliers. NOTE: Replace bent or damaged circlips. Check exhaust port gasket condition. (Recommended replacement exhaust port gaskets, Harley part number:17048-98 or 65324-83A)

Yamaha Road Star Trike Conversion Installation Manual

0

Filed Under (Yamaha) by admin on 17-02-2011

download
Removal of Original Parts a. Disconnect the battery. b. Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. c. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for re-installation after modification are noted. • Rider’s Seat (to be re-installed without modification) • Passenger Seat (to be reinstalled without modification) NOTE: OEM front / rear seat mount bracket and rear seat mounting bolt to be retained and reused. • Passenger Back Rest w/ Mounting Rails (to be re-installed without modification) NOTE: Back rest to mounting rail hardware to be reused. Mount rail to vehicle frame not to be reused. • Left and right passenger foot rests (to be re-installed without modification) • Drive Pulley / Belt cover (to be re-installed without modification) • Mufflers (to be re-installed and relocated with minor modification) • Rear Fender (complete w/ sub frame and all attaching parts) NOTE: Upper Forward Fender Mounting Bolt to be retained and reinstalled. • Shock Absorber to Swing Arm Mounting Bolt (to be re-installed) • Swing Arm and Rear Wheel (complete w/ all attaching parts) NOTE: Swing Arm Pivot Bolt, washer and nut to be retained and reinstalled. • Brake Line to Rear Master Cylinder • Drive Belt Core Return There are NO core return parts for this model Installation of Champion Trike Conversion Kit 4.1 Install Drive Belt a. Install supplied drive belt to transmission output pulley. (Refer to OEM manual) Figure 1 b. Drive belt cover to be reinstalled later. 4.2 Install Champion Swing Arm a. Install Champion Swing Arm to vehicle using the OEM pivot bolt, washer and nut. Figure 2 b. Attach OEM shock absorber to swing arm using OEM hardware. c. Torque pivot bolt nut to 90 lb. ft. d. Torque lower shock hardware to 43 lb. ft. 4.3 Install Rear Drive Assembly a. Install tension bolts and jam nuts to adjuster

Yamaha Road Star Motorcycles Trike Conversion Removal And Installation Manual

0

Filed Under (Yamaha) by admin on 09-11-2010

download
Removal of Original Parts a. Disconnect the battery. b. Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. c. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for re-installation after modification are noted. • Rider’s Seat (to be re-installed without modification) • Passenger Seat (to be reinstalled without modification) NOTE: OEM front / rear seat mount bracket and rear seat mounting bolt to be retained and reused. • Passenger Back Rest w/ Mounting Rails (to be re-installed without modification) NOTE: Back rest to mounting rail hardware to be reused. Mount rail to vehicle frame not to be reused. • Left and right passenger foot rests (to be re-installed without modification) • Drive Pulley / Belt cover (to be re-installed without modification) • Mufflers (to be re-installed and relocated with minor modification) • Rear Fender (complete w/ sub frame and all attaching parts) NOTE: Upper Forward Fender Mounting Bolt to be retained and reinstalled. • Shock Absorber to Swing Arm Mounting Bolt (to be re-installed) • Swing Arm and Rear Wheel (complete w/ all attaching parts) NOTE: Swing Arm Pivot Bolt, washer and nut to be retained and reinstalled. • Brake Line to Rear Master Cylinder • Drive Belt Core Return There are NO core return parts for this model. nstallation of Champion Trike Conversion Kit 4.1 Install Drive Belt a. Install supplied drive belt to transmission output pulley. (Refer to OEM manual) Figure 1 b. Drive belt cover to be reinstalled later. 4.2 Install Champion Swing Arm a. Install Champion Swing Arm to vehicle using the OEM pivot bolt, washer and nut. Figure 2 b. Attach OEM shock absorber to swing arm using OEM hardware. c. Torque pivot bolt nut to 90 lb. ft. d. Torque lower shock hardware to 43 lb. ft. 4.3 Install Rear Drive Assembly a. Install tension bolts and jam nuts to adjuster plates. Figure 3 Qty per Assm Spec Description 2 M10 x 1.25 x 70 Hex Head Bolt 2 M10 x 1.25 Hex Nut b. Install adjuster plates to rear drive pinch blocks. Hardware installs from inboard to outboard side. Snug, but do not tighten hardware at this time. Figure 4

Incoming search terms:

HONDA VTX 1800 AND VTX1300 SWING ARM COVER INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-12-2010

download
1. Remove the two (2) 6mm bolts holding the brake hose clips in place. 2. Slide the cover in from the rear over the swing arm and align the holes. (NOTE: on Retro models and some aftermarket exhausts it is necessary to remove the two (2) muffler mounting bolts and loosen the two (2) exhaust nuts on the rear cylinder head then pull the exhaust outward to gain clearance to slide the cover into position). 3. Replace the original front bolt or bolts into the cover and hose clip. NOTE: the hose clip should go behind the chrome cover and it may be necessary to straighten out the bend in the clip slightly to gain alignment of the holes. Replace the rear bolt with the one supplied and tighten both securely. 4. Replace and tighten the exhaust bolts if removed earlier

HONDA VT 1100 HIGHWAY MOUNTS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Remove the parts supplied from the package and lay them out in front of you. Remove the screws from the mounts and clamps. See photo (1), notice that the two clamp halves (1A) and the two arms (1B) are the same. Notice that the two mounts (1C) are different and are machined at opposite angles. The mounts (1C) can be installed facing forward to the front of the bike as shown in photo (1) or facing to the rear of the bike as shown in photo (2) depending on how far forward you want the pegs to be located. 2. Starting on the right side choose which way you want the mount to face. Hold one of the mounts up against the frame tube. Hold one of the arms up against the mount where it bolts together. The arm should be horizontal or level when the bike is sitting up straight. If not use the mount with the opposite angle. Next while still holding the mount in place at the desired location place one of the clamps behind the mount and start the screws. Snug the screws only leaving them loose enough to make further adjustments later. Next Bolt one of the pegs loosely to the arm as shown in photo (2). Notice that there are eight dowel pin holes on the mount and seven on the back side of the arm allowing 56 possible angles or positions for the arm to be set at. Holding the arm/peg assembly up to the mount select the desired position for the arm and place one of the dowel pins supplied into the nearest set of holes on the mount and arm. Bolt the arm/peg assembly to the mount using one of the large button head Allen screws and a washer provided. Once you have the arm close to where you want it you can make fine adjustments by removing the large Allen screw, removing the arm and moving the dowel pin to the next hole in the mount. Moving the pin clockwise one hole will rotate the arm in the opposite direction approximately ½”. Likewise moving the pin counter clockwise will rotate the arm in the opposite direction. 3. Repeat this procedure on the left side. Sit on the bike. Place your feet on the highway pegs and verify that you have them set at the most comfortable position for you and that they are set the same on both sides. Tighten all bolts and screws securely

Incoming search terms: