1986 goldwing air shock replacement boot

You search Auto repair manual PDF 1986 goldwing air shock replacement boot, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1986 goldwing air shock replacement boot Direct Download speed 5282 Kb/s

  1986 goldwing air shock replacement boot Full Version speed 6162 Kb/s



MOUNTAIN BIKE AIR SHOCK SET-UP AND TUNING GUIDE

0

Filed Under (Tips and Review) by admin on 01-12-2010

download
DETAILED SET-UP 2. Installing Air Pressure – Remove the air cap from the Schrader valve on the end of the shock body. Attach the pump to the Schrader valve. Some people damage their pumps by screwing them on too far. As soon as the gauge registers pressure, screw 1/2 turn more and pump to the desired level. Use the release button on the pump to reduce air pressure. The hiss you hear when unscrewing the pump is only the air from the pump and not from the shock! Likewise, when you install the pump again, you will also hear a hiss as air from the shock fills the pump and reduces the registered pressure you previously installed. All perfectly normal when pressurizing the shock! After removing the pump, be sure to reinstall the Schrader valve cap. If the shock does not dampen properly after pressurizing, the air pressure may have been lost during pump removal as a result of a worn pump fitting o-ring that needs replacement. Do not ride the bike until the shock is properly pressurized. 3. Main Air Spring Pressure Adjustments – Air Spring adjustments are made by inflating or deflating the main air spring chamber. Since your IFP air pressure adjustment (outlined above) also affects your starting spring force, you should always adjust your IFP pressure before adjusting the main air spring pressure. You can refer to the online Quick Start guide at: www.progressivesuspension.com/literature.html for accurate main air spring pressure and sag settings matched to your bike model and body

Air Shock Installation Instructions

0

Filed Under (Tips and Review) by admin on 24-11-2010

download
Air HoseInstallation. Choose the most convenient loca- tiononyour motorcycle for the air fill valve. Drilla 5/16″hole and install the air fill valve as shown in Figure 3orsecure air fill valve to frame tube. 2. Keep hose ends clean during installation because dirt can cause air leaks. 3. Install hose connector, tube clamp and two O-rings onto one end of the air hose (See Figures4&5) Apply rubber lubricant (soap solution, not oil) to the O-rings to ease installation on the air hose& into the shock absorber inlet. Plastic connector should just bottom on fitting. Do not overtighten! The function of the nut is to hold everything together in place, the O- rings do the sealing. Fin- gertightenonly (10 in/lb maximum). 4. After routing the air hose, trim the length to fit air fill valve. Install hose connector, tube clamp, and twoO-rings onto end of hose (See figures 4&5). Lubricate as above and assemble to air fill valve. Use the same procedure formating hose. Important —leaveasmall amount of slack in hose near shock absorber to allow for the slight move- mentofthe shock. Caution! Do not install hose near ex- haustsystem, battery or any other sharp edges or seat movement. Keep hoses clear of moving parts such as wheels or suspension components. Do not allow hoses to have excess slack and sag below the motorcycle. The hoses could catch on road surfaces or debris and could be damaged while the motorcycle is in motion. 5. If necessary the air hose can be secured along the motorcycle’swiringharness with tie-wraps. 6. Testing: Inflate system to 50 psi. Apply soapy water solution to all connections and check for air leaks. If there are any leaks, disconnect the suspected fitting and check for dirt or damage to the air line or the O-rings. Remove any dirt or foreign matter, re-lubricate the O-rings and reinstall. If unable to locate the leak, remove rubber boot from shocks and submerge pressurized components under water (in- cludingT-Valve) and check for leaks. If you cannot solve the air leak problem, please contact our technical staff for assistance

HARLEY-DAVIDSON SOFTAIL MODELS STEALTH AIR SHOCK MOUNTING

0

Filed Under (Harley Davidson) by admin on 16-12-2010

download
INSTALLATION 1. Remove the seat, inner fender, and ignition coil cover. Removing the rear wheel assembly is recommended for ease of installation, but not absolutely necessary. Remove the nut cup and outer grommet on each of the Works shocks. If you intend to leave the ride height at stock height for road riding, position the inner nut cup SHOC KS SHOC KS WORKS PERFORMANCE PRODUCTS, INC. 21045 Osborne St., Canoga Park, CA 91304 818.701.1010 fax 818.701.9043 STEALTH AIR SHOCK MOUNTING FOR HARLEY-DAVIDSON SOFTAIL MODELS 2000-ON #HDAIR-00 – 02/15/2006 WARNING! THESE SHOCKS MUST ONLY BE USED WITH STOCK SWINGARMS AND ON STOCK FRAMES WITH THE STOCK BOTTOMING BUMPERS ON THE CHASSIS TO LIMIT THE TRAVEL OF THE SHOCKS. AFTERMARKET SWINGARMS, OR MODIFIED SWINGARMS THAT DO NOT HAVE THE UPPER BRACE THAT ACTS AGAINST THE BOTTOMING BUMPERS CANNOT BE USED WITH THESE SHOCKS. INCREASING THE TRAVEL BY ELIMINATING THE BUMP STOPS OR A NON-STANDARD SWINGARM DESIGN WILL ALLOW THE TIRE TO MAKE CONTACT WITH THE FENDER OR OTHER CHASSIS COMPONENTS, AND CAN DAMAGE THE SHOCKS. 19. Lock Washers 20. Long Bolts (2) 21. Short Bolts (2) 13. Din Plug Screw 14. Din Plug Gasket 15. Cap 16. Eye Spacers (4) 17. Cotter Pins (2) 18. Switch Bracket 7. Compressor Bracket 8. Harness 9. Fuse Block 10. Din Connector 11. Solenoid 12. Hose 1. Damper Shock 2. Air Spring Shock 3. Nut Cup 4. Grommet 5. Hose 6. Compressor 1 2 3 4 5 6 7 8 9 10 11 12 13 15 16 17 14 18 19 20 21 Fig. 1–Nomenclature on the damper shock up against the ring nut. The shocks are now ready to install. 2. Place the motorcycle on a suitable frame stand allowing unrestricted access to the shocks. 3. Place a small screw jack under the swing arm to support the weight as well as allow you to position the swing arm correctly to line up the shock mounting bolts. Remove stock shocks. 4. Install the left side (damping) shock with the stock mounting bolt. Make sure that the bolt threads and threaded portions of the frame are free of oil and grease. Grease the shoulders of the bolts and use thread lock compounds on the threads. Discard the stock shock washers on both shocks. Do not use any washers- -including the stock washers on these bolts. Use only the spacers included. The 3/16-inch wide spacers are used on each side of the shock eye. Do not “double-up” the spacers together on either side of the shock eye, as this will cause misalignment of the shocks which can lead to premature wear or damage to the shocks. 5. Put the supplied spacers on each side of the eye. The shoulder of the bolt must protrude a small amount through the shock eyes in order to allow the shock to pivot freely. This is extremely important. With the shocks fully tightened, the spacers should be free to rotate with finger pressure. If the washer is used or a non-stock bolt is used, the bolts will work loose or break because the shocks are in a bind.

Victory Freedom Engines Installation Instructions for S&S Air Cleaner Kit

0

Filed Under (Victory) by admin on 31-10-2010

download
1-Locate and remove the Intake Air Temperature Sensor (IATS) from the stock Polaris Victory air box. Locate the new position for the IATS on the bottom of the S&S air cleaner. Push the IATS in the lower air cleaner cover and turn1⁄ 4 turnin either direction, make sure you feel it lock into place. Inspect from the inside of the air cleaner to ensure that the barbs are locked into place. See Picture 1. 2-Using the stock Polaris Victory air box gasket (PN 5811908) and S&S supplied (Qty 4) M6 fasteners, assemble the lower air cleaner cover to the throttle body using 243 Blue Loctite®on the treads. Torque the M6 fasteners to 72-96 inch pounds. 3-Position the S&S pre-formed air filter onto the lower air cleaner cover ensuring that it fits into the machined groove. 4-Install the top air cleaner cover on top of the filter ensuring that it fits into the machined groove. 5-Make surethat the filter is situated in the machined grooves on both the top and bottom air cleaner covers. 6-Using 243 Blue Loctite on the threads of the S&S supplied (Qty 3) M6 fasteners tighten down top air cleaner cover evenly until seated. Finish torque the fasteners to 72-96 inch pounds. Now you’re ready for breather hose and barometric pressure hose routing. 7-Locate the S&S supplied 3⁄ 16 “reinforced hose and clamps. Push one end of the hose on the 3⁄ 16 “brass barb in the bottom air cleaner cover and slide clamp up around the end of the hose. The other end of the hose is for the Barometric Pressure Sensor (MAP). Route the hose towardthe back of the engine over the top of the rear rocker cover. 8-Remove the MAP sensor from the stock Polaris Victory air box. Remove the orange rubber gasket from the MAP sensor. Slide the S&S supplied clamp over the 3⁄ 16 “rubber hose that leads to the air cleaner. Push the barbed end of the MAP sensor into the 3⁄ 16 ” rubber hose and slide clamp up to the end of the hose around the barb. A small amount of lubricant may be applied to the barb on the MAP sensor to make installation easier. 2 S&S Air Cleaner Assembly 41-0021 (Calibration cardnot shown) Picture 1 CAUTION WARNING WARNING Plastic barb locked in recess.
9-Assemble and install breather hose as follows: A-Cut the stock Victory®hose on the straight section just behind the 90 degree bend as shown in Picture 2 . B-Slide an S&S supplied 1⁄ 2 “hose clamp over the modified stock breather hose. C-Install the S&S straight barb in Victory breather hose and position a hose clamp around hose end. D-Slide the 90-degree end of breather hose over the brass barb on the air cleaner cover and slide hose clamp in place. E-Position straight end of the S&S breather hose over the 1⁄ 2 “barb to connect to the Victory hose. Slide clamp over connection. F- See Pictures 3 and 4 for breather hose and barometric pressuresensor hose installation positions. NOTE: S&S breather hose can be cut for best fit

Incoming search terms:

ATK 50MX INSTALLATION AND ADJUSTMENT TIPS

0

Filed Under (Atk) by admin on 01-11-2010

download
PRELOAD ADJUSTMENT— On some Works shocks a threaded preload is standard. This allows the adjustment of the ride height of the motorcycle. The preload is changed by turning a threaded nut down towards the spring (higher ride height) or up away from the spring (lower ride height). The nut is a right-hand thread. CHECKING RIDE HEIGHT— 1. With the bike unloaded on the side stand and the shock fully extended, have an assistant measure from a point at the axle (center point) to a point on the frame, fender or bodywork directly above it. Record this measurement. 2. With the bike off the stand and the rider in the seat, bounce on the suspension and let the bike settle. Have the assistant measure from the same two points. Subtract the second measurement from the first. HM CRX50 / BAJA & ATK 50MX INSTALLATION AND ADJUSTMENT TIPS Continued on next page. #HM50 – 5/27/99 #HM50 – 5/27/99 To Front Valve Mounting channel Spacer Flange Shock eye Top View of Shock Mount Fig. 1 Top view of upper shock mount. The flange on the shock bushing must face toward the spacer. The valve should point toward the front of the bike Fig. 1 Top view of upper shock mount. The flange on the shock bushing must face toward the spacer. The valve should point toward the front of the bike 3. The amount of settle, or “sag” is a function of the wheel travel. It should only be between 1/4 and 1/3 of the total travel. 4. If the difference is less than the minimum, reduce the spring preload. Measure the distance again starting with Step 2. Adjust again if necessary. 5. If the difference is more than the maximum, increase the spring preload. Measure the distance again starting with Step 2. Adjust again if necessary. Note: If the ride height is too low, the shock will bottom unnecessarily, resulting in a harsh ride. If the ride height is too high, the shock will “top out” too easily when rebounding from a bump or under hard deceleration. NITROGEN PRESSURES IN EMULSION SHOCKS CAUTION: The pressure in these shocks cannot successfully be checked. Concerns with the gauge volume and the gas volume in the shock body create a situation where you cannot accurately determine what pressure was in the shock. In addition when the pressure is lowered (i.e. checking the pressure) the gas and some of the shock oil escapes into the gauge. It is possible to lose a large percentage of the shock oil by depressing the core of a charged shock to the atmosphere. Please note that in order to check the pressure, some of the gas must escape and fill the gauge assembly. The volume of the gas pocket is about half the size of your thumb, so a very small volume change results in a large pressure drop. Because the gauges’ volumes vary, it is not possible to deduce the actual pressure in the shock prior to attaching the gauge. Therefore it is imperative that any attempt to check pressure be accompanied by the capability of refilling the shock. In other words: If you don’t have a nitrogen source handy, don’t check the pressure! PRESSURIZING EMULSION SHOCKS The pressure setting for Works gas shocks is 250 p.s.i. of dry nitrogen. To pressurize a shock with some residual pressure in it, bring the gauge manifold up to 250 p.s.i. and depress the core with the T-handle. This will either equalize the pressure or refill the shock without transferring oil from the shock into the gauge assembly. The best gauges for this purpose screw on to the valve and incorporate a T-handled core depressor to isolate the shock from the gauge. This allows a leak-free separation once the desired pressure is reached. For simplified operation, an extra valve is provided for the filling apparatus, allowing pressure adjustment with the gauge in place. Works offers a suitable gauge and filling manifold. Most motorcycle shops that deal with dirt bikes can pressurize the shock

Incoming search terms:

Vespa GTS Super Specification

0

Filed Under (Vespa) by admin on 11-11-2010

download
Gts super 300 ie Gts super 125 ie s 125cc s 50cc Gts 250 ie Gts 125cc LX 125cc LX 50cc 2 stroke Engine Single-cylinder, catalised, QUASAR 4 stroke, 4 valve electronic injection Single-cylinder LEADER 4 stroke with electronic injection Single-cylinder LEADER 4 stroke Single-cylinder HI-PER 2 stroke Single-cylinder, catalised, QUASAR 4 stroke, 4 valve electronic injection Single-cylinder, catalised, LEADER 4 stroke, 4 valve Single-cylinder LEADER 4 stroke Single-cylinder HI-PER 2 stroke Capacity 278cc 124cc 124cc 50cc 249cc 124cc 124cc 49cc Power 16.4 kW / 7500 rpm 10.5 Kw / 9500 rpm 7.65 Kw / 8250 rpm 3.2 Kw / 7500 rpm 15.7 Kw / 8500 rpm 7.65 Kw / 8250 rpm 7.65 Kw / 8250 rpm 2.5 Kw / 8500 rpm Max Torque 22Nm / 6500 rpm 12 Nm / 8000rpm 9.6 Nm / 7250 rpm 4.4 Nm / 6500 rpm 20.1 Nm / 6500 rpm 9.6 Nm / 7250 rpm 9.6 Nm / 7250 rpm 3.3 Nm / 6500 rpm Cooling Liquid Liquid Forced Air Forced Air Liquid Liquid Forced Air Forced Air Starter Electric Electric Electric and kick starter Electric and kick starter Electric Electric Electric and kick starter Electric and kick starter Transmission Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Front Suspension Single arm, dual chamber hydraulic shock absorber with coaxial spring Single arm link with coil spring and double hydraulic shock absorber Single arm link with coil spring and double hydraulic shock absorber Single arm link with coil spring and double hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Rear Suspension Two dual effect shock absorbers with adjustable preload Coil spring and double hydraulic shock absorber Coil spring and double hydraulic shock absorber Coil spring and double hydraulic shock absorber Twin hydraulic shock absorbers with preload adjuster Twin hydraulic shock absorbers with preload adjuster Hydraulic shock absorbers with preload adjuster Hydraulic shock absorber Front Brake ø 220mm disc brake 220mm disc brake ø 200mm disc brake ø 200mm disc brake ø 220mm disc brake ø 220mm disc brake ø 200mm disc brake ø 200mm disc brake Rear Brake ø 220mm disc brake 220mm disc brake ø 110mm drum brake ø 110mm drum brake ø 220mm disc brake ø 220mm disc brake ø 110mm drum brake ø 110mm drum brake Front Tyre Tubeless 120/70-12″ Tubeless 120/70 – 12″ Tubeless 110/70 – 11″ Tubeless 110/70 – 11″ Tubeless 120/70-12″ Tubeless 120/70-12″ Tubeless 110/70 – 11″ Tubeless 110/70-11″ Rear Tyre Tubeless 130/70-12″ Tubeless 130/70 – 12″ Tubeless 120/70 – 10″ Tubeless 120/70 – 10″ Tubeless 130/70-12″ Tubeless 130/70-12″ Tubeless 120/70 – 10″ Tubeless 120/70-10″ Running weight 158kg 158kg 114kg 96kg 151kg 145kg 114kg 96kg Length/Width/Height 2230mm / 755mm / 1170mm 1930mm / 755mm / 1930mm 1770mm / 740mm / 1140mm 1755mm / 740mm / 1140mm 1930mm / 755mm / 1170 mm 1940mm / 755mm / 1180 mm 1770mm / 740mm / 1140mm 1755mm / 740mm / 1140mm Fuel Tank Capacity 9 litres 9 litres 8.5 litres 8.5 litres 9.2 litres 10 litres 8.5 litres 8.5 litres Emmissions Euro 3 Euro 3 Euro 3 Euro 2 Euro 3 Euro 3 Euro 3 Euro 2 Colours Rosso Dragon Nero Lucido Montebianco Rosso Dragon Nero Lucido Montebianco Taormina Nero Lucido Montebianco Taormina Nero Lucido Montebianco Marrone Terra Di Toscana Bronzo Perseo Nero Vulcano Blu Midnight

Incoming search terms:

2009 Kawasaki ULTRA 250X/ 260X FUEL INJECTION CONTROLLERS And REGULATORS INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
The R&D high performance Air Filter Kit will improve acceleration and top speed performance by increasing air flow and reducing air temperatures that enter directly into the Ultra 250X’s air plenum box area. The O.E.M. air plenum box on the Ultra 250X is a great design that will flow plenty of air. However, the air that feeds the plenum box is heated by the engine. R&D has created an easy to install “flat filter” that installs directly in place of the large center access inspection cover located directly under the main glove box. The R&D Flat Air Filter insert will allow unrestricted fresh and cool air to enter the air plenum box area which will add power you can feel and a nice high performance tone. The R&D Performance Filter Kit also features two filters, one for each of the surge and blowoff protections valves. The O.E.M. surge valve recycles compressed hot air back into the air box plenum at idle and under deceleration conditions. The R&D surge and blowoff valve filter kit removes the air recycling hoses which will keep the hot air from entering the air plenum box reducing the engines intake air temperatures. The R&D Ultra 250X Air Filter Kit offers great performance tips on how to remove the restrictive air vent hoses which will further reduce the under seat ambient air temperatures. The R&D Filter system does not remove or alter the O.E.M. plenum box in any way, therefore there are no questions to be answered regarding water ingestion

Incoming search terms:

HARLEY DAVIDSON LOW REAR SHOCK KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
See Figure 3 and Table 1. INSTALLATION Shock Absorbers Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) Installation of any accessory suspension components can affect cornering clearance. This could distract the rider, causing loss of control and death or serious injury. (00431b) NOTES This procedure requires that both shocks be removed prior to installing the new shock absorbers. You need to place the motorcycle on a center stand with the rear wheel raised off of the ground. The jiffy stand should be able to move through its full range of travel. The exhaust system may interfere when removing and installing the lower right shock mounting hardware. If necessary, see Service Manual and remove the rear exhaust pipe. 2 4 5 7 1 6 3 is05206 1. Lower screw 2. Upper screw 3. Lower washer 4. Upper washer 5. Cover 6. Nut 7. Shock absorber Figure 1. Remove / Install Shock Absorber 1. Block the motorcycle under the frame so that the motorcycle is securely resting upright, the jiffystand may be moved through its full range of travel, and rear wheel is just off the ground. 2. Remove the lower shock mounting screw (1), washer (3) and nut (6) from the shock absorber (7). Save the hardware for reuse. 3. Remove the upper bolt (2), washer (4) and cover (5) and remove the shock absorber. Save the hardware for reuse. 4. Repeat Steps 1 and 2 for opposite side and save the hardware. 5. Apply 2-3 drops of LOCTITE 243® (blue) on the threads of the lower mounting bolt, then install bolt, lower washer and nut to the shock. 6. Apply 2-3 drops of LOCTITE 243® (blue) on the threads of the upper mounting bolt, then install the shock cover, upper mounting bolt and washer to the shock. Verify the cutout in shock cover locates properly

Triumph Bonneville America And Speedmaster The Freak Installation Instructions and Parts List

0

Filed Under (Triumph) by admin on 29-10-2010

download
INSTALLATION In order to install The Freak, the factory air-box must be removed. Because of it’s design, the factory air-box is not an item that is easily removed. There are several parts that must be removed in order to get the air-box out of the bike in one piece. We recommend using the following method to remove your air box without having to cut it into smaller pieces in order to get it out of the frame. 1. PARTS REMOVAL In order to gain access to the air-box, it is necessary to remove certain parts of the motorcycle to gain access to the air-box area of the frame. Removing the following parts should be the first steps you take. A. Seats – Remove both seats starting with the passenger pillion, if applicable. B. Side cover and grommets – Remove the plastic side cover on the right side (throttle side) of your motorcycle. This is the faux oil-tank cover that has the name of your bike on it. Underneath the side cover there are three rubber grommets (1 on the frame tab, and two on the air-box) that support the side cover. Remove the two that are on the air-box and leave the one on the frame. You will attach the two that you removed to the right side bracket in Section 4C . C. Faux air filter covers – On the right side of the bike, remove the chrome faux air filter covers, by removing the one allen head screw that holds it onto the air-box. On the left hand side (clutch side) remove the faux air filter cover in the same manner, you removed the one on the right. D. Plastic shrouds – on the left side, remove the black plastic air-box shroud, by removing the two allen head screws holding it in place. Then remove the plastic shroud covering your fuse box (this is the piece that surrounds your ignition terminal next to the battery). E. Battery – Remove the battery by unscrewing the torx-head bolt that holds the chrome bracket in place. Remove the chrome bracket and the black plastic cap. Tilt the battery out of the box with the top towards you. Disconnect both battery terminal connectors, negative (-) terminal first. Remove the battery. F. Battery box – Remove the two bolts that hold the battery box to the frame. Pull the battery box out as far as you can, then remove the the ignition terminal from the battery box, by removing the two allen screws that hold it in place from the back. Next, remove the fuse box from the battery box, by pushing it out from the back. It is not necessary to disconnect any of the wiring going to the fuse box, or the ignition terminal. G. Rear fender – Remove the rear fender, by first disconnecting the taillight wires. Follow the wires from the tail light assembly on the inside of the rear fender (left side) towards the front of the bike until you come to the box connector. Disconnect the tail light wires at this connector, being careful not to break it. Once the wiring is disconnected, remove the 6 bolts that hold it to the struts. Have someone hold the fender for you while you are removing all of the bolts so that it does not drop once the bolts are removed. Slide the fender out the rear of the bike. 2. PREPARE THE MOTORCYCLE FOR AIR-BOX REMOVAL To remove the factory air-box without damaging it, it is necessary to lift the bike. We recommend the use of a multi-position ATV/motorcycle jack with a minimum lift height of 10″. A. Setting up the lift – Place the lift under your bike and secure your bike to the lift according to the lift manufacturer’s instructions. B. Raise slightly – Lift the motorcycle to the point where the rear springs are without tension, but NOT to where the rear tire is off the ground. C. Remove the rear springs – Take off each of the rear springs by removing the the two bolts on each spring. Once all the bolts are removed gently pull the springs out off of the studs. If they do not pull off easily, you can raise or lower the bike slightly with the lift to ease tension on the spring. Remember, you should not have the rear tire off the ground at this point. The bike should only be raised enough to relax the tension in the springs. D. Remove the mufflers – Remove the mufflers by loosening the clamp at the exhaust header, and by removing the rear foot peg hangers. If the mufflers are not removed, they can become damaged by the axles in Section 2H . E. Disconnect the carburetors – With a small flathead screwdriver, pull the retainer springs out of the channel of the carburetor intake tubes (the two large black tubes coming from the air box into the back of each carburetor), and simply push them towards the air box off of the carbs

Incoming search terms:

HARLEY DAVIDSON TOURING SUSPENSION AIR PUMP KIT OPERATION/ INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
OPERATION 1. Remove cap from air suspension air valve and connect pump by threading the air valve adapter (1) on the pump as shown in Figure 1. When adapter is threaded properly, the current air pressure in the system will be indicated on the gauge of the pump. Do not exceed maximum air pressure for rear suspension. Air components fill rapidly. Therefore, use low air line pressure. Failure to do so may result in possible damage to components. (00165a) NOTES See the motorcycle’s Owner’s Manual or, if installed, the air suspension lowering kit’s instruction sheet for the recommended air pressures. Using pressures outside the recommended loading range will result in a reduction of available suspension travel and reduced rider comfort. 2. To increase pressure, operate the air pump handle (4) until the desired pressure is indicated on gauge (2). Use caution when bleeding air from the suspension. Moisture combined with lubricant may leak onto the rear wheel, tire and/or brake components and adversely affect traction, which could result in death or serious injury. (00084a) NOTE The pressure release button is designed to release pressure slowly. If the button is completely or rapidly depressed, no air will be released. For the best results, depress the pressure release button slowly and only partially. 3. To decrease pressure, slowly depress the pressure release button (3) on the pump until desired pressure is indicated on gauge (2)