1993 goldwing master cylinder removal

You search Auto repair manual PDF 1993 goldwing master cylinder removal, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1993 goldwing master cylinder removal Direct Download speed 5282 Kb/s

  1993 goldwing master cylinder removal Full Version speed 6162 Kb/s



HARLEY DAVIDSON CHROME MASTER CYLINDER AND CLUTCH BRACKET KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
MASTER CYLINDER REMOVAL See Figure 1. Master cylinders designed for dual disc (two caliper) operation have an 11/16 inch (17.5 mm) bore, while those that are designed for single disc (one caliper) operation have a 9/16 inch (14.3 mm) bore. The bore size is stamped (1) on the master cylinder assembly inboard of the handlebar clamp bracket. NOTE Do not use an 9/16 inch bore master cylinder assembly on dual disc (two caliper) models or dual disc 11/16 inch bore master cylinder assembly on single disc (one caliper) models. These master cylinder assemblies are not interchangeable. Using the wrong assembly can adversely affect braking efficiency or result in brake failure which could result in death or serious injury. D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) 1 is 01230 1. Bore stamp size location Figure 1. Verify Correct Master Cylinder Bore Size 1. Open bleeder nipple caps on front brake caliper. Install end of a length of clear plastic tubing over caliper bleeder valves, while placing free end in a suitable container. Open bleeder valves about 1/2-turn. Pump brake hand lever to drain brake fluid. Close bleeder valve. Avoid leakage. Be sure gaskets, banjo bolt(s), brake line and master cylinder bore are clean and undamaged before assembly. (00322a) 2. Remove bolt and two steel/rubber washers to disconnect fitting of hydraulic brake line from master cylinder. Discard washers. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 3. See Figure 2. Place the cardboard insert between the brake lever and lever bracket

Incoming search terms:

HARLEY DAVIDSON CHROME FRONT BRAKE MASTER CYLINDER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
1. See Figure 2. Drain the brake fluid. a. Open bleeder nipple cap on front brake caliper. b. Install end of a length of clear plastic tubing over caliper bleeder valve, while placing free end in a suitable container. c. Open bleeder valve about 1/2-turn. d. Pump brake hand lever to drain brake fluid. e. Remove cover. f. Close bleeder valve. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) 2. Remove bolt and 2 steel/rubber washers to disconnect fitting of hydraulic brake line from master cylinder. Discard washers. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) is 01010 Figure 3. 5/32 in. (4 mm) Cardboard Insert 3. See Figure 3. Place the cardboard insert between the brake lever and lever bracket. 4. Using T27 TORX® drive head, remove the 2 screws with flat washers securing the handlebar clamp to the master cylinder housing. Remove the brake lever/master cylinder assembly and clamp from the handlebar. Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) 5. Remove retaining ring from pivot pin groove at bottom of master cylinder bracket. 6. Remove pivot pin and brake hand lever from master cylinder assembly. NOTE New master cylinder comes with all internal components preassembled. It is not necessary to remove the components from the bore of the old master cylinder. See Figure 9. Use denatured alcohol to clean clutch system components. Do not use mineral-based solvents (such as gasoline or paint thinner), which will deteriorate rubber parts even after assembly. Deterioration of these components can cause clutch failure, which could result in death or serious injury. (00296a) 7. With denatured alcohol, clean and inspect all parts that will be reused. Replace as necessary and wipe dry with a clean lint free cloth

Incoming search terms:

Yamaha Road Star Forward Control Kit Installation Instructions

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Before starting to assemble this forward kit on your motorcycle check the packing list to make sure that the kit you received is the correct one for your model motorcycle and that the foot pegs are the style you ordered (billet or ISO). Next check the contents hardware kit P.N.0109-1000 against the packing list for completeness. Installing The Shift Control Photo 1 Remove wires from horn. Remove the two hex head bolts (Save for later installation) that mount the OEM shift controls to your motorcycle. Unthread stock shift rod at trans shift arm, leaving OEM rod end connected to stock shift arm. Using Original Metric hardware, place a drop of Loctite #242 (blue) to the bolt threads and mount the shift control plate to the motorcycle frame, Photo 2. FORWARD CONTROL KIT PM SHIFT CONTROL ASSEMBLY Note Before torquing the shift control mounting bolts down, tighten them snug and look behind the shift control mounting plate to where it contacts the mounting lug on the frame. Make sure it fits squarely to the lug before proceeding further. Torque the two shift control mounting bolts down to 25 ft-lb. Using a 3/8″ x 1″ hex head bolt with a lock and flat washer put a drop of Loctite #242 (blue) on the threads and insert the bolt through the rear of the control mounting plate and attach the foot-peg pivot to it. Tighten the bolt while holding the footpeg pivot so that its hinge is lined up in a 45˚ rear facing angle. Thread supplied shift rod coupler to stock shift rod end at trans arm. Mount the shift pedal to the other end of the shift ro d using a 5/16″ x 1″ socket head screw and Nylocnut . Adjust the transmission shift linkage so that the shift arm on the forward controls and the shift arm on the transmission are parallel. Secure it with the jam nuts. Apply a drop of Loctite #242 (blue) to the threads under the jam nut before tightening see Photo 3 After you have assembled the shift control onto your motorcycle you must align the footpeg. The folding footpeg assembly uses a blind stud to attach the footpeg to the footpeg pivot. Shim washers (3/8″ x .015″) are used on the stud between the footpeg and the pivot, see Photo 4, so that the top surface of the footpeg is correctly aligned for your foot when it is tightened down on the pivot. This is done by setting a couple of shim washers on the footpeg mounting stud “A” and then screwing the footpeg onto the mounting stud, if the footpeg is rotated to far forward then add another shim washer, if not far enough then remove a shim washer. After you have the selected the correct number of shims for your footpeg, disassemble the footpeg and put a drop of Loctite #271 (red) on both ends of the stud and reassemble the footpeg. This will also need to be done on the brake control footpeg. Setting Up the Master Cylinder The master cylinder pushrod return spring and pushrod boot must be installed on the master cylinder before it is assembled onto the forward control mount. The parts are shown in Photo 5: pushrod boot (A), pushrod return spring (B), spring seat washer (C), and master cylinder (D). Place the return spring seat washer into bore of master cylinder so that is sits on top of the piston retaining snap ring. Next set the pushrod return spring on the seat washer and slide the pushrod boot over the return spring now slip the big end of the boot over the flange on the master cylinder so that the ridge on the inside of the boot fits into groove “A” that is machined into the end of the master cylinder flange, see Photo 6. Installing The Brake Control Unplug stock brake light switch at master cylinder. Remove brake line from rear caliper. Remove the existing brake controls from your motorcycle down to the control mounting lug that is welded on to the frame’s right side, see Photo 8. Save Metric hardware for later use. A Shim Washer PHOTO 4 A B C D PHOTO 5 A PHOTO 6 PHOTO 7 Note For complete brake system removal instructions and precau – tions refer to the appropriate service manual for your year and model motorcycle

Incoming search terms:

Yamaha WR 250F and WR450F Dual Sport Kit REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 20-01-2012

download
license Plate Mount Installation: Locate the aluminum license plate mount and license plate light assembly. Remove the rear most nut securing the stock taillight assembly (underneath the fender) (don’t lose the little compression tube and washer). Temporarily install the license plate mount to this location and mark the fender where it needs to be drilled for the rear mounts. Drill the fender in two places with a ¼” drill and reinstall the license plate assembly using the stock taillight mount and the 6 x 20 mm countersunk screws, bezels and nylock nuts Rear Turn Signal Installation: Locate the two rear turn signals in the kit – they’re the ones with the longer wires. Drill a 3/8 hole in each side of the fender as shown in Photo 3 and attach them as shown in Photo 4. It does no matter which signal goes on which side. Run the left turn signal wires forward along with the taillight wires, up through the grommet in the fender to the area just behind the air box cross member and above the fender. Run the right turn signal wires forward along the right frame rail, and through the same hole you made for the license plate wires Brake Light Switch Installation: The WR250/450 uses a hydraulic brake switch. This requires replacing the rear master cylinder banjo bolt with a specially made switch. Installing the switch requires bleeding the rear brake. If you do not feel competent bleeding your rear brake, please refer this job to a qualified mechanic, as failure to do it correctly will make the brake inoperable. Remove the rear master cylinder guard. Remove the bolt holding the brake fluid reservoir to provide access to the master cylinder. Loosen the banjo bolt securing the rear brake line to the master cylinder. Typically, this bolt will be very tight and loosening it will bend the support hanger for the master cylinder if not supported. Brace the master cylinder with a wrench or lever. Remove the banjo bolt and replace with the hydraulic switch. Make sure to install the copper crush washer from the stock bolt under the switch. Torque the switch assembly to 25 lb-ft.

Yamaha Forward Control Kit INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 17-01-2012

download
After you have assembled the shift control onto your motorcycle you must align the footpeg. The folding footpeg assembly uses a blind stud to attach the footpeg to the footpeg pivot. Shim washers (3/8″ x .015″) are used on the stud between the footpeg and the pivot, see Photo 4, so that the top surface of the footpeg is correctly aligned for your foot when it is tightened down on the pivot. This is done by setting a couple of shim washers on the footpeg mounting stud “A” and then screwing the footpeg onto the mounting stud, if the footpeg is rotated to far forward then add another shim washer, if not far enough then remove a shim washer. After you have the selected the correct number of shims for your footpeg, disassemble the footpeg and put a drop of Loctite #271 (red) on both ends of the stud and reassemble the footpeg. This will also need to be done on the brake control footpeg. Setting Up the Master Cylinder The master cylinder pushrod return spring and pushrod boot must be installed on the master cylinder before it is assembled onto the forward control mount. The parts are shown in Photo 5: pushrod boot (A), pushrod return spring (B), spring seat washer (C), and master cylinder (D). Place the return spring seat washer into bore of master cylinder so that is sits on top of the piston retaining snap ring. Next set the pushrod return spring on the seat washer and slide the pushrod boot over the return spring now slip the big end of the boot over the flange on the master cylinder so that the ridge on the inside of the boot fits into groove “A” that is machined into the end of the master cylinder flange, see Photo 6. Installing The Brake Control Unplug stock brake light switch at master cylinder. Remove brake line from rear caliper. Remove the existing brake controls from your motorcycle down to the control mounting lug that is welded on to the frame’s right side, see Photo 8. Save Metric hardware for later use

HARLEY DAVIDSON CHROME/BLACK FRONT MASTER CYLINDER COVER KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION Do NOT allow dirt or debris to enter the master cylinder reservoir. Dirt or debris in the reservoir can cause improper operation and equipment damage. (00205b) NOTE If this is a master cylinder cover replacement, start with step 1. If this is new installation for a hydraulic clutch kit, go to step 3. D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) 1. Clean front master cylinder cover, then remove the two screws that hold the cover in place. 2. Remove the original cover (with sight glass) and gasket. 3. Put new cover and gasket in position. 4. See Service Parts illustration. Install the new cover screws (1) and tighten to 6-8 in-lbs (.7-.9 Nm). Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) NOTE The cover is lab led for D.O.T. 4 brake fluid. Install this cover on reservoirs filled only with D.O.T. 4 brake fluid. Do not mix grades of brake fluid. as they are not compatible and could cause equipment damage.

Incoming search terms:

HARLEY DAVIDSON HEATED HAND GRIP KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
REMOVAL Preparation To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow the instructions given to remove the main fuse. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. Remove the fuel tank according to the service manual instructions. -J04259 1 of 8 Left-Side Grip Removal 1. See Figure 1. Using a T-25 TORX drive head, remove the upper and lower switch housing screws (1). 2. Using a T-27 TORX drive head, loosen the upper screw securing the handlebar clamp (3) to the clutch lever bracket. Remove the lower clamp screw with flat washer. Loosen the clamp and position the clutch hand lever assembly away from the switch housing. Separate the upper and lower switch housings. 3. With “glueless” grip: Remove the grip from the handlebar. With glued grip: Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. 2 2 1 5 4 3 1 is01283 1. Switch housing screws 2. Grooves 3. Handlebar clamp 4. Left handlebar grip 5. Larger diameter of flange Figure 1. Left Handlebar Switch Housing Right-Side Grip Removal Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) NOTE A section of corrugated cardboard or the eyelet of an ordinary cable strap can be used for this purpose. See Figure 2. 1. Place a 5/32-inch (4 mm) thick insert between the brake lever and the lever bracket. 2. Using a T-25 TORX® drive head, remove the upper and lower switch housing screws. 3. Using a T-27 TORX drive head, loosen the upper screw securing the handlebar clamp to the brake master cylinder housing. Remove the lower clamp screw with flat washer. Loosen the clamp and position the master cylinder assembly away from the switch housing. Separate the upper and lower switch housings. 4. Remove the grip from the handlebar. NOTES The twist grip sensor in the right side of the handlebar has a seal cap that protects internal electrodes from dirt and moisture, and also serves as a retention device for the throttle grip. To remove the grip, a slight tug may be necessary to release the index pins in the grip from the receptacle in the seal cap. Upon removing the grip, check the location of the seal cap. If the seal cap is still fastened to the index pins inside the old throttle grip, it can be discarded along with the grip. If the seal cap is still fastened to the end of the twist grip sensor: •See Figure 3. Insert a small screwdriver or other flat-blade tool into the flat area on one side of the seal cap. •Press the leg on the underside of the cap to free it from the slot at the end of the twist grip sensor. Pry up one end of the cap. •Repeat on the other side of the cap. •Carefully remove the cap and discard it

Incoming search terms:

HARLEY DAVIDSON MULTI-FIT BRAIDED THROTTLE/ IDLE CABLE KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect battery cables, negative (-) cable first or remove the main fuse following the instructions in the service manual. NOTE When performing cable disassembly procedures, make careful notes as to the existing cable routing. Pay special attention to existing cable strap locations before removing so new straps can be placed into the same locations. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 2. See Figure 1. Place the cardboard insert between the brake lever and lever bracket. 3. See Figure 2. Loosen cable adjuster jam nuts. Turn cable adjusters in until they are as short as possible. This will provide enough slack for easy removal. 4. Remove the right upper and lower switch housing screws INSTALLATION Throttle and Idle Cable Installation 1. See Figure 3. Apply graphite lightly to the throttle grip inside the switch housing and on the throttle end of the handlebar. NOTE The throttle control cable has a larger diameter retaining ring crimped to the cable end than does the idle control cable. For assembly, apply a drop of light oil on the retaining rings of the crimped inserts. 2. See Figure 7. Push the throttle cable housing and retaining ring into the larger hole of the switch housing, located in front of the tension adjuster screw. 3. Push the idle cable housing and retaining ring into the smaller hole of the switch housing, located behind the tension adjuster screw. 4. Push the throttle and idle control cable housings into the lower switch housing until each snaps into place. NOTE For models not equipped with factory-installed cruise control, if the friction shoe has fallen out or become dislodged, install the shoe with the concave side facing up and position it so the pin hole is over the point of the adjuster screw. 5. Push the throttle control grip over the end of the right handlebar until it bottoms against the closed end. Rotate the grip until the ferrule notches are at the top. To prevent binding, pull the grip back about 0.12 inch (3.2 mm). 6. See Figure 3. Position the lower switch housing beneath the throttle control grip. Install two brass ferrules (Item 3, Figure 11) from this kit onto cables, seating the ferrules in their respective notches on the throttle control grip. The cables must be captured in the grooves molded into the grip. 7. Position the upper switch housing over the handlebar and lower switch housing. Route the wire harness conduit through the depression at the bottom of the handlebar. 8. Tighten the upper and lower switch housing screws finger- tight. 9. Position the brake lever/master cylinder assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the top of the brake lever bracket. 10. Align the holes in the handlebar clamp with those in the master cylinder housing and tighten the lower screw and flat washer finger-tight. Position for rider comfort. Beginning with the top screw, tighten the screws to 60-80 in-lbs (6.8-9.0 Nm)

HARLEY DAVIDSON XLH 1200cc BIG BORE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
Boring and Honing Procedures 1. Check again for burrs on cylinder gasket surfaces and remove burrs before performing Step 2. 2. Install original head and base gaskets, CYLINDER TORQUE PLATES (Part Number 33446-A) and TORQUE BOLTS (Part Number 33446-4). Tighten TORQUE BOLTS following tightening procedure given in the INSTALLATION, CYLINDER HEAD procedure in the ENGINE section of the Service Manual. NOTE Torque plates, properly tightened and installed with gaskets, simulate engine operating conditions. Measurements will vary as much as 0.001 inch without torque plate. 3. The cylinder must be bored with gaskets and torque plates attached. Bore the cylinder to 0.003 inch under the desired finish size. 1 WARNING CAUTION CAUTION 1 WARNING Kit Number 4. Hone the cylinder to its finished size (See Figure 1) using a 280 grit rigid hone followed by a 240 grit flexible ball hone. Honing must be done with torque plates attached. All honing must be done from the bottom (crankcase) end of the cylinder. Work for a 60 degree crosshatch pattern. 5. See Figure 1. After machining and honing, chamfer the bottom edge of the cylinder liner. the chamfer provides a beveled surface for easier installation of the cylinder over the piston rings. Break leading edge of liner to a flat surface. The bottom edge of the liner will be somewhat sharp after machining. This sharp edge could easily be damaged during installation of the cylinder. Piston Installation The 1200cc pistons have an arrow on the top of the piston. This arrow must face the front of the engine when piston is installed. There is no front cylinder piston or rear cylinder piston. New pistons can be installed in either cylinder. Check piston rings for proper side clearance and end gap (See XLH Service Manual). Be sure end gaps of adjacent rings are installed 90 degrees apart. Assembly Follow assembly and torque specifications given in the ENGINE section of the applicable Service Manual. Replace original gaskets, O-rings and seals with new components furnished in kit. NOTE Push rod covers on 1991 and later models are one-piece and the correct O-rings are as follows: Bottom – Part Number 17944-89 Upper – Part Number 11190 Engine Break In For the first 500 miles, to wear-in critical parts, observe these few simple driving rules: During the first 50 miles, keep the engine speed below 2500 RPM in any gear. Up to 500 miles, vary the engine speed, avoiding any steady speed for long distances. Engine speed up to 3000 RPM is permissible in any gear. Avoid fast starts at wide open throttle. Drive slowly until engine warms up. Avoid running the engine at extremely low RPM in higher gears. 2 of 3 -J00001 1200cc CYLINDER FINAL BORE SIZE AFTER HONING STANDARD BORE DIAMETER 3.4980 inch + 0.0002 inch Figure 1. Bottom Edge of Cylinder Liner Chamfer i04852 Break Edge to Flat Surface

Incoming search terms:

TRIUMPH 750 BIG BORE CYLINDER AND PISTON SET FOR 650 TWINS INSTALLATION

0

Filed Under (Triumph) by admin on 29-10-2010

download
Step 1. Unpack your big bore kit and inspect the contents. There should be the following: 1. Cylinder x l 2. piston with wristpin x 2 3. Hepolite piston ring set x l 4. Special big bore head gasket Step 2. Thoroughly wash the cylinder bores with soap and water. Do not use solvent! Dry bores with air or a lint free towel and let completely air dry. This step is most important and will greatly extend the life of the pistons. Step 3. Following the procedure outlined in your service manual, drain the fuel tank, remove the exhaust system, fuel tank and carburetors. Have a catch basin handy to capture any fuel that may spill from the carburetors, as fuel is highly flammable and can be ignited by a dryer pilot light etc. from a long distance. Clean up any spilled fuel immediately and dispose of away from any source of ignition. Store the fuel tank in a well vented area, outdoors is best, in the event your fuel taps should leak. Step 4. Remove the rocker boxes by slacking the 9 head bolts a little at a time in a star pattern. Remove the 6 nuts at the front and back of the head. Remove the 4 corner rocker box bolts. Remove the head bolts and rocker boxes. Remove the push rods. Examine the push rods to insure they are straight and the ends are tight. Replace any suspect push rod. Step 5. Remove the cylinder head. Now would be a good time for guide and valve renewal. This is best left to an expert. More cylinder heads have been ruined by auto machine shops than by hard use. If you do not have a qualified shop in your area please call for a referral. Step 6. Remove the push rod tubes and the cylinder base nuts. Clip rubber bands around the top of the lifters to keep them from dropping into the crankcase. Have a few lint free rags handy. Bring the pistons to the top of the stroke and begin lifting off the cylinder. If the cylinder is hard to lift off, thread a nut on one of the base studs and use a tire lever to pry against the bottom fin close to its base using the stud as a fulcrum. After partially raising the cylinder stuff the crankcase mouth with rags to keep any carbon or broken rings from entering the crankcase. These will remain in place until step 12. Step 7. Leaving the rags in the crankcase remove the wrist pin circlips from the pistons and discard. Heat the piston and gently push the wrist pin out. Do not use force as this can damage the connecting rod or its bearings. Be sure to account for all the clips as one left in the crankcase can do extensive damage. Step 8. Clean all gasket surfaces to remove any traces of the old gaskets. Use Pennatex gasket remover if needed. Be very careful not to scratch the gasket surface or to allow any gasket particles to enter the crankcase. Even a small bit of gasket can stop the oil pump from working! Step 9. Note the direction and location of the lifters. These must be replaced in the same position as when removed. Remove the lifter blocks from the old cylinder. Start by removing the small retaining bolts and washers. The lifter blocks are extremely fragile and are easily broken. They are also very expensive so great care must be taken in this step! Triumph special tool 222-616008 is advisable here. Apply pressure to the center of the block only. Do not press against the tangs that locate the lifter! A tool can be fabricated using two dowels to locate in the lifter holes. Step 10. Clean and examine the lifters and camshaft faces. Clean the lifter blocks and remove the sealing oring under the locating flange. Replace these with the new orings in the gasket set. Apply a smear of gasket sealant to the lifter block oring and press into the new cylinder. Be sure the lifter block is parallel with the bores and the grooved block is on the exhaust side. Apply a small amount of assembly oil to the lifters and replace in the exact position they came from

Incoming search terms:

Incoming search terms: