1996 flh spedometer

You search Auto repair manual PDF 1996 flh spedometer, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1996 flh spedometer Direct Download speed 5282 Kb/s

  1996 flh spedometer Full Version speed 6162 Kb/s



1996+ HARLEY DAVIDSON FLH INNER AND OUTTER FAIRING MOUNT FOR HONDA VTX 1300 installation

0

Filed Under (Tips and Review) by admin on 09-04-2012

download
This mount was made to attach the HD FLH assembled fairing to the 4 fork mounting points on the VTX 1300 using the Memphis Shades mounts. This allows use of the MS allen wrench to quickly remove the fairing if needed. You will have to make or buy a headlight extension. Has to be done first. I used a 5″ x 5″ x .5″ piece of aluminum stock and made one to bump the headlight out 4″. There will be some trimming and relocating of brackets. And you’ll have to buy longer bolts to mount everything correctly. Get the headlight squared away first, then do the fairing. Take a length of 1″ aluminum angle stock and cut two 17″ pieces from it. These will be the uprights for the “H” brace. Measure 5.5″ from the bottom of one piece and center punch for a hole. Drill a large enough hole to slip over the MS mounting hardware on the forks. Start at about ½” bit and notch out as necessary. Center of this hole has to be 5.5″ from the absolute bottom of the angle iron. In the same location, drill out another notch for the bottom mounting point. A drill press is handy for these modifications and you can hog out the mounting notches with a file, dremmel, etc., until they fit. Do the same for the other length of 1″ angle stock but make sure it is a mirror image of the first one. Test fit these by mounting them to the MS fork brackets using the MS bracket hardware. Bottom notch goes in first, then the top notch. I epoxied the back “nuts” of the mounting hardware to the fork mounting brackets. It keeps it in place when you’re taking the fairing on and off the bike. On the top mounting points, I epoxied a washer with one side ground flat to the bolt’s mounting ferule. This allowed better contact between the H brace and the fork mounting bracket. Didn’t want that fairing falling off. Adjust as necessary and after the test fit, remove.

HARLEY-DAVIDSON FLH/ FLT MODELS 1985-1996 REAR LOWERING KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 04-03-2012

download
may encounter clearance problems when re-installing the saddlebags. Check for a minimum of 5mm. clearance to prevent damage to the saddlebags. Measure clearance in the recessed area in the “backside” of the saddlebags where the shock sits. Check front, back and side clearance. THE BAGS MUST INSTALL WITHOUT UNDO FORCE. If they don’t, they are hitting the shock and/or shock boot. ****************** Inspect the clearance through the full range of motion of the swing arm ******************* n If more clearance is required, three suggested options are as follows: 1. Place washers between the mounting points where the saddlebags attach to the rails. This will move the bag slightly outward and away from the shock body. NOTE: On saddlebags utilizing DZUS FASTENERS (’85-’92), replace these with bolt/nut combination (as on ’93-’94 years). This will allow you to use washers to gain necessary clearance. 2. Remove or slide off the rubber boot that covers the shock shaft and attaches the body of the shock. The boot can be modified and reattached to the shaft (not the body) and secured with nylon ties and/or removed completely. This should gain you a minimum of 3mm of clearance. 3. Slot and/or space the saddlebag “rail/frame cage” mounting holes to allow the entire frame assembly to be moved out slightly from the shock body. You should use this modification only as a last resort n Lower motorcycle and check preload (shock spring stiffness). Adjustment may be necessary to suit personal preference in ride comfort. Read your Harley-Davidson owners manual for procedure. Test Ride.

Incoming search terms:

Toyota Camry, 1992-1996 Avalon Repair & Service Manual

0

Filed Under (Toyota Manuals) by admin on 25-05-2011

epair manual covers all Toyota Camry 1992-1996, and Toyota Avalon models, 1995-1996.

Table of Contents

* Introduction: Vehicle identification numbers. Buying parts. Safety. Maintenance techniques. Chemical and lubricants, and more.
* Tune-up and routine maintenance
* Four-cylinder engine
* V6 engines
* General engine overhaul procedures
* Cooling, heating and air-conditioning systems
* Fuel and exhaust systems
* Engine electrical systems
* Emissions control systems
* Transmission

Incoming search terms:

Harley Davidson FLH EZ-Steer Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 22-03-2012

download
Installation of the Champion EZ-Steer system is similar to the installation of the OEM triple clamp of your Harley Davidson FLH Motorcycle. We recommend that you use an OEM service manual and follow the prescribed disassembly, installation and torque specifications for the upper and lower clamp assembly. Before Installing Kit (2008 & Prior) The wiring bracket of the OEM upper triple clamp needs to be modified to fit the Champion upper triple clamp. After removing / disassembling the OEM parts from your motorcycle, position the OEM wiring bracket onto the Champion upper clamp as shown. Scribe the ID of the steering stem hole onto the wiring bracket and enlarge the hole to scribe line. This will allow the wiring bracket to fit over the new Stem Lock-Nut. Install OEM handle bar mount assemblies to Champion upper clamp using Item #5 (Handle Bar Mount Spacer). The spacers are used on top of the upper clamp. Installation Notes • Be sure to use the correct fork extension. Yellow 2002 and newer (non adjustable air pressure). Black for 2001 and older (adjustable air pressure). Be sure to double check the fork cap (Fork Tube Plug) being removed. • Reinstall the OEM O-rings on Item #7 (Fork Extensions) prior to installing in the fork tubes. • On some of the Road King models with chrome headlight Nacelle, Item #9 must be mounted underneath upper clamp Item #2 to ensure enough room for air fittings. • Be sure to replace fork covers in proper order, during installation of the fork tubes. • Thoroughly clean sides of steering neck and install self adhering rubber stops where steering stop screws contact frame. • Secure wires and cables clear of steering stop bolts. • Do not torque Item # 1 (½-20 x 1-1/4″ Hex Head Bolt) until fork tubes have been installed to assembly. • Note the torque specification for the items listed in the table below.

Harley-Davidson FLH Series 2008 and Down, Independent Suspension Trike Conversion Installation Manual

0

Filed Under (Harley Davidson) by admin on 07-03-2012

download
Protect yourself and others when you have a vehicle up in the air. Anytime you lift a vehicle, either by hoist or a jack, make sure that it is securely supported. b. Make sure the engine is turned off and battery disconnected before you begin work.  Carbon Monoxide poisoning from exhaust gases: Be sure there is adequate ventilation whenever you run the engine.  Burns from hot parts: Let the engine and exhaust system cool before working on those areas.  Injury from moving parts: If running the engine, keep hands, fingers and clothing away from moving/rotating parts. c. Gasoline vapor and hydrogen gases from batteries are explosive. To reduce the possibility of fire or explosion, be careful when working near gasoline and batteries. d. Use only nonflammable solvent, not gasoline, to clean parts e. Never drain or store gasoline in an open container. f. Keep all cigarettes, sparks or flame away from the battery and all fuel related parts. 1.5 Specifications Overall Length: 103″ Overall Width: 57.25″ Wheel Base: 53″ Load Capacity: 600 Lb Tire Size (15″): 205 / 70 / R15 Wheel Size (15″) (4 lug) Offset +35 mm 15x7JJ 4 on 4.5 Tire Pressure: 24-26 PSI Suspension: Double A-arm Independent Rear Differential: Custom-built rear differential utilizing OEM drive belt. Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 5.75 cubic feet. Two full-face helmets and additional storage.
Harley-Davidson® FLH 2008 & Down Independent Suspension CHAMPION TRIKES Installation Guide Page 6 of 20 Revision 4 2 Removal of Original Parts Secure and raise motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted.  Seat – to be re-installed; without modification.  Left and right side covers – to be re-installed after modification.  Tour Box – to be re-installed (if so equipped).  Left and right saddle bags (if so equipped).  Left and right rear crash bars, saddlebag rails (if so equipped).  Tour Box mounting frame (if so equipped).  Left and right passenger foot rests – to be re-installed without modification.  Left and right mufflers  Rear wheel NOTE: Prior to removing rear wheel, depress foot brake and secure in down position (e.g., zip-tie to floor board). This will prevent fluid flow when rear brake Caliper is removed.  Remove Rear Caliper (disconnect brake line at Caliper). NOTE: Cap line to prevent introduction of dust / debris into line. Remove Caliper

HARLEY-DAVIDSON FLH/ FLT AND SOFTAIL (FLST) Owner's Maintenance Notes

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
1. Tire Pressure and Rotation : Keep the nominal tire pressure at about 20-25psig. It is not necessary to periodically rotate the trike tires unless you experience unusual tire wear. 2. Bearing Lubrication . Your Swing Arm, external differential and axle bearings are sealed and do not require greasing. However, should you experience unusual differential or axle bearing noise you should take your trike to a Champion Trike Dealer or to your motorcycle mechanic for a checkup. 3. Body Lubrication . There are no grease fittings on the trike body and no required body lubrication points. 4. Differential lubrication . Your differential is a sealed unit and comes filled with high-pressure grease. No maintenance is required. 5. Brakes . Check your brake system fluid level every 3,000 miles and top-off as necessary. Inspect rear disc brake pads every 10,000 miles and replace as necessary. Pads are Volkswagen Part # D101P 6. Drive Train . Inspect your drive belt as recommended in your motorcycle Owner’s Manual. When properly tensioned after the trike conversion, the belt should “deflect” about 1/2 to 5/8 inches when pressed with a force of 10 pounds. Do not use commercial belt dressing compounds on the belt: these compounds are designed for friction, not toothed, belts and can collect dirt and sand. 7. Suspension System. FLH/FLT : The suspension system retains your two OEM shocks and is designed to give you the best ride with a load of no more than 500 pounds (passengers plus cargo plus trailer tongue weight). Keep the air pressure in the shocks in the range of 30-70 psig: Softail (FLST) : The suspension system retains your single OEM shock and adds two coil-over “helper” mechanical shocks. The system is designed to give you the best ride with a load of no more than 500 pounds (passengers plus cargo plus trailer tongue weight). There is a pre-load adjuster ring on each new shock that is factory-set at the “lowest” setting, for the softest ride. Changing this setting will result in a stiffer ride. 8. EZ-Steer (rake kit) : If your trike is equipped with Champion’s EZ-Steer, the bearings are a wear item. You should follow your motorcycle manufacturer’s recommended front-end triple-tree maintenance requirements. Generally these call for an initial service at 1,000 miles followed by periodic maintenance at 10,000 mile intervals.

Incoming search terms:

2009 Harley-Davidson FLH Series Independent Suspension Trike Conversion Installation Manual

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
Important Safety Precautions a. Make sure you have a clear understanding of all basic shop safety practices and that you wear appropriate clothing and use safety equipment. Be especially careful of the following: · Read all directions before you begin, and make sure you have the tools, the parts and the skills required to perform the tasks safely and completely.Harley-Davidson® FLH 2009 & Up Independent Suspension CHAMPION TRIKES Installation Guide Page 5 of 18 Revision 8 · Protect your eyes by using proper safety glasses, goggles or face shields anytime you hammer, drill, grind, pry or work around pressurized air or liquids, and springs or other stored-energy components. · Use other protective wear when necessary, for example gloves or safety shoes. Handling hot or sharp parts can cause severe burns or cuts. · Protect yourself and others when you have a vehicle up in the air. Anytime you lift a vehicle, either by hoist or a jack, make sure that it is securely supported. b. Make sure the engine is turned off and battery disconnected before you begin work. · Carbon Monoxide poisoning from exhaust gases: Be sure there is adequate ventilation whenever you run the engine. · Burns from hot parts: Let the engine and exhaust system cool before working on those areas. · Injury from moving parts: If running the engine, keep hands, fingers and clothing away from moving/rotating parts. c. Gasoline vapor and hydrogen gases from batteries are explosive. To reduce the possibility of fire or explosion, be careful when working near gasoline and batteries. d. Use only nonflammable solvent, not gasoline, to clean parts. e. Never drain or store gasoline in an open container. f. Keep all cigarettes, sparks or flame away from the battery and all fuel related parts. 1.6 Specifications Overall Length: 103″ Overall Width: 57.25″ Wheel Base: 53″ Max Load Capacity: 600 Lb Max Tire Size (15″): 205 / 70 / R15 Wheel Size (15″) (4 lug) Offset +35 mm 15x7JJ 4 on 4.5 Tire Pressure: 24-26 PSI Suspension: Double A-arm Independent Rear Differential: Custom-built rear differential utilizing OEM drive belt. Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 5.75 cubic feet. Two full-face helmets and additional storage. *Champion does not change certain components that will affect EPA, CARB, or any laws that will change the emission characteristics of the motorcycle.

Incoming search terms:

Harley-Davidson Six Speed Transmissions FLH 2009 Up Champion Reverse Gear Installation Instructions

0

Filed Under (Harley Davidson) by admin on 17-02-2011

download
Preparation Remove Original Parts From Vehicle. 2.1 Purchase a small tube of Loctite #262 (red) for use later. 2.2 To torque the large gear: 2.2.1 Purchase Snap-On (or equivalent) filter tool. Part #: FWA62121. OR 2.2.2 Purchase Champion special tool – Part # RG-100-100 2.3 Drain the transmission oil. 2.4 Remove front and rear exhaust header pipe. 2.5 Remove the clutch release cover (right side). 2.6 Remove throw out bearing assembly. (to be reinstalled later without modification) 2.7 Remove the two nuts from the main and counter transmission shafts. WARNING : Do not attempt to push shafts into gearbox or remove the trap door – This can cause spacers inside the gearbox to be miss-aligned and lock up the gearbox when gears are installed and tightened. 2.8 Remove clutch push rod (to be replaced w/ Champion supplied rod) Note: For hydraulic clutch bikes, obtain Champion Part # RG-100-082, a longer push rod) Snap-On Part No: FWA62121 Snap-On Part No: FWA62121 Champion Part No: RG-100-100 Reverse Gear Installation Instructions Harley-Davidson Six Speed Transmission HD FLH 2009 Up Page 3 of 5 Revision 2 Boring Tool 3 Installation 3.1 Thoroughly clean threads of main and counter shafts using a silicon remover. 3.2 Apply the green thread locking compound (supplied) to main shaft threads and screw the small gear onto the main shaft. Figure 1 3.3 Install the supplied (ear)plug into the main shaft hole. To be removed later. 3.4 Install the supplied special tool to the small gear. Ensure the holes of the special tool align with the holes in the small gear. Figure 2 3.5 Install torque wrench to special tool and torque the small gear to 80 lb. ft. 3.6 Remove torque wrench from special tool. Do not remove special tool from small gear. 3.7 Using the supplied boring tool and the special tool as a guide, drill the main shaft through two holes of the special tool as shown. Stop when cutter contacts bearing race. Figure 3 3.8 Remove special tool, leaving main shaft plug in place, and thoroughly clean out the holes. Use care to ensure debris does not enter transmission. 3.9 Remove plug from main shaft hole. Figure 1 Figure 2 Figure 3 Note: To prevent gears from rotating during torque procedures, engage transmission into 1st gear and apply brakes Note: Frequently stop cutting and remove bit from hole to clean bit and vacuum debris from hole

Incoming search terms:

Harley-Davidson FLTR/ FLH/ FLHT/ FLHR EFI models 1995-2001 Variable Pressure Fuel Regulator Intallation manual

0

Filed Under (Harley Davidson) by admin on 27-04-2012

download
1 . Ensure vehicle runs correctly through all rpm ranges and idles correctly before attempting any work. It is highly recommended that a pressure / flow test be carried out before & after installation of the VariReg to determine fuel system condition . Stock HD 300 kPa / 44 psi, VariReg as delivered 360 kPa / 52 psi Note: In some countries gas stations do not “final filter” the fuel & therefore we recommend that the fuel filter canister be replaced every 15,000 klms (10,000 miles). Restriction of the fuel by way of a blocked or partially blocked filter will result in difficulty in tuning or failure to obtain satisfactory results during tuning. Should you experience difficulties in tuning, see Diagnosing fuel filter and pump faults 2. Remove air filter cover, air filter and backing plate. Check Throttle Position Sensor value at completely closed throttle as best performance will be obtained at the nominated settings. This will require backing off the idle screw and cold start idle actuator and screw adjustment as described in the workshop manual. The original T.P.S. values should be recorded for possible future reference. To set TPS values without the HD breakout box see VariReg TPS Setting for Harley-Davidsons The T.P.S. values must be set to 1995 – 1996 175 mV (+/- 25mV) 1997 – 2001 275 mV (+/- 25mV) Record the original TPS value here. ………………..mV YOU MUST ENSURE THROTTLE PLATES ARE COMPLETELY CLOSED AND NO BINDING EXISTS IN CABLES to obtain the correct value setting. 3. Reset idle screws to approximate previous settings, no need to start the engine. 4. Complete full or partial fuel tank removal as described in workshop manual. 5. Remove stock fuel pressure regulator as described in workshop manual and leave Horn removed from vehicle until after tuning, this will allow ease of access to the regulator

Incoming search terms:

FLH Harley-Davidson Bikes/ Trikes Steering Damper Installation Manual

0

Filed Under (Harley Davidson) by admin on 12-04-2012

download
First, we’re going to install the upper Bracket. (#8 in Fig. 1) Start by placing a clean towel or other protective material over your front fender to protect it from falling objects. Remove the 5/16-18 Allen head bolt and washer holding the top of the crash bar to the frame. Use a ¼” Allen wrench. Access is easier if you crank the forks over to one side. Line up the hole in the new bracket with the crash bar, orienting the bracket to the crash bar as shown in Fig. 1, and re-install the bolt with a drop of blue loc-tite. Torque the bolt to 15-20 ft. lb. If you don’t have a torque wrench, well, you should have one, but if not, 15-20 ft. lb. is a bit tighter than a spark plug torque, which is 12-18 ft. lb. If you are not sure, snug it down tight, but don’t try to break it. Note than on a couple of these, I had to slightly elongate the hole in the bracket to re-install the upper crash bar bolt. (Side mount bracket installation) Next, the side bracket install. (#6 in Fig. 1) You’ll need a #35 Torx driver to remove the two screws holding the LEFT passing lamp/turn signal bar to the bike/trike. Carefully remove the upper and lower screws, holding the bar to prevent it from falling, possibly jerking the attached wiring. Once you have removed the screws, you can let the bar hang, while you orient the side bracket as per Fig. 1. Re-install the two screws you just removed, capturing the damper side bracket under the light bar. Use a drop of blue loc- tite here as well. Hand tighten the two screws, aligning the lamp bar and damper side bracket. Using your torque wrench, (you did find one didn’t you?) Tighten the two screws to 15-20 ft. lb. Ok the easy part is out of the way.

Incoming search terms: