1997 dyna front end triple tree diagram

You search Auto repair manual PDF 1997 dyna front end triple tree diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1997 dyna front end triple tree diagram Direct Download speed 5282 Kb/s

  1997 dyna front end triple tree diagram Full Version speed 6162 Kb/s



HARLEY DAVIDSON CHROME DYNA TRIPLE TREE INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
INSTALLATION NOTE The components in this kit install exactly as the OE (Original Equipment). 1. Refer to the applicable Service Manual for steering head removal procedures. 2. Refer to the applicable Service Manual for steering head installation procedures. SERVICE PARTS 1 5 4 3 2 is05169 Figure 1. Service Parts: Dyna Chrome Steering Head -J02511 1 of 2 Table 1. Service Parts Table Part Number Description (Quantity) Item 48365-48A Steering head bearing dirt guard 1 4307 Socket head cap screw 0.38-16 x 1.5 in. 2 4306 Socket button head cap screw 0.38-16 x 1.5 in. 3 46183-99 Bracket, upper fork, chrome 4 45503-02 Lower triple clamp assembly, chrome 5 45611-86 Retaining ring (not shown) 6

Daytona 675, Street Triple Street Triple R Fitting Instruction

0

Filed Under (Triumph) by admin on 29-10-2010

download
remove the original gear selector rod from the motorcycle. Note: The ball joint and locknut on the transmission linkage have a left hand thread. This is identified by either a machined ring on the gear selector rod on Daytona 675 or on the ball joint on Street Triple and Street Triple R. 1. Front ball joint 2. Locknut 3. Gear selector rod 4. Machined ring, left hand thread identification 5. Machined ring, left hand thread identification (StreetTriple and Street Triple R) 6. Remove the front and rear ball joints and front locknut only from the gear selector rod. Retain the locknut and both ball joints for re-use. Retain the gear selector rod if the motorcycle is to be returned to its original condition. 7. Remove the plastic end caps from the quickshifter assembly. 8. Screw the locknut on to the rear of the quickshifter assembly (right hand thread) leaving 8mm of thread exposed. 1. Quick shifter assembly 2. Locknut 9. Screw the rear ball joint (right hand thread) on to the rear of the quickshifter assembly until it contacts the locknut. Unscrew the ball joint, only enough to achieve the correct orientation in relation to the quickshifter cable, as shown below. Finger tighten the locknut at this stage. 1. Ball joint 2. Quickshifter assembly 3. Locknut 4. Quickshifter cable 10. Fit the locknut and front ball joint (left hand thread) to the front of the quickshifter assembly Screw the locknut and ball joint on to the quickshifter assembly to achieve a dimension between the ball joint ends of 203.5 mm. Ensure that the ball joint is in the correct orientation to the quickshifter cable, as shown below. Finger tighten the locknut at this stage. 1. Ball joint 2. Quickshifter assembly 3. Locknut 4. Quickshifter cable 12. Route the quickshifter cable through the gear selector rod aperture in the frame, as shown. 1. Quickshifter cable 2. Gear selector rod aperture 13. Locate the quickshifter assembly in position, through the frame with the sensor at the rear and the cable at the top. 1. Quick shifter assembly 2. Sensor 14. Attach the front ball joint to the transmission linkage. 1. Ball joint 2. Transmission linkage

Incoming search terms:

HARLEY DAVIDSON SCREAMIN' EAGLE STREET PERFORMANCE TOURING END CAP MUFFLER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-04-2011

download
PRODUCT INFORMATION Noise Emission Warranty Harley-Davidson warrants that these mufflers, at the time of sale, meet all applicable United States E.P.A. Federal noise and Emissions standards. This warranty extends to the first person who buys these mufflers for proposes other than resale, and to all subsequent buyers. Warranty claims should be directed to an authorized Harley-Davidson Dealer. Tampering Prohibition Federal law prohibits any modification to this exhaust system which causes the motorcycle to exceed the Federal noise standard. Use of the motorcycle with such a modified exhaust system is also prohibited. NOTE This product should be checked for repair or replacement if the motorcycle noise has increased significantly through use. Otherwise, the owner may become subject to penalties under state and local ordinances. INSTALLATION NOTE Install end caps on mufflers before installing mufflers on vehicle. Install Direct Bolt-On End Caps 1. See Figure 1. Install end cap (2) to muffler (3) with four socket head cap screws (1). Tighten to 82-86 in-lbs (9.3- 9.7 Nm) . 2. Repeat for opposite side muffler. 3 2 1 is05426 1. Socket head screw (4) 2. End cap 3. Muffler Figure 1. Install End Cap on Muffler Install Attachment Ring End Caps 1. See Figure 2. Slide the three U-nuts (2) onto the bosses of the end cap attachment ring cup on the muffler. 2. Install attachment ring (1) to muffler with four socket head cap screws (3). Locate the attachment ring with a U-nut in the 12 o’clock position. Tighten to 82-86 in-lbs (9.3-9.7 Nm) . 3. Slide end cap (5) onto muffler body being careful to align holes in end cap with U-nuts. 4. Install the three countersunk screws (4) and tighten screws securely. 5. Repeat for opposite side muffler

Incoming search terms:

HARLEY DAVIDSON DYNA SPROCKET KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
1991-1992 Dyna models: Screw (5) 3739A 1993-1995 FXDL, 1995 FXD and FXDS, all 1997-1999 Dyna models: Screw (5) 3730A 1993-1995 FXDWG and all 1996 Dyna models: Screw (5) 3769 1991-2005 Dyna models: Washer (5) 6516HW 2000-2006 Dyna models: Screw, with lock patch (5) 3737A 2006 Dyna models: Screw, with lock patch (5) 3873 2007 and later Dyna models: Screw, with lock patch (5) 3109 The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) Kit Contents There are no Service Parts available with this kit. INSTALLATION NOTES The cotter pin or spring clip for the rear axle nut must be replaced during assembly and is available for purchase from a Harley-Davidson dealer. The five sprocket mounting screws must be replaced when replacing the sprocket. Remove existing sprocket according to service manual instructions. Remove all residual threadlocking agent from fastener holes using an appropriate thread chasing device and compressed air.

Incoming search terms:

HAR:EY DAVIDSON FLHR/C/S (Road King) FRONT END LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Removal (Left and Right Forks) 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to Touring Model Service Manual and remove front wheel, fender and brakes. 3. Refer to Touring Model Service Manual and remove headlamp nacelle. 4. Loosen fork cap bolt from fork tube plug at top of fork tube, but do not remove. 5. See Figure 1. Standing at front of vehicle, loosen pinch bolt (with lockwasher) on right side of lower fork bracket, but do not remove. 6. Spray glass cleaner on fork tube above the rubber fork stop. After lubricating surfaces, move fork stop up fork tube until it contacts bottom of upper fork bracket. 7. Holding fork slider to prevent fork from dropping, remove fork cap bolt from fork tube plug. Slide fork tube down and out of upper fork bracket, fork stop, lower fork bracket and slider cover. 1 WARNING 1 WARNING 1 WARNING 1 of 5 ® Kit Number 54614-05 Figure 1. Loosen Pinch Bolt on Lower Fork Bracket i04808 1 Fork cap bolt 2 Fork stop 3 Pinch bolt 8. Thread fork cap bolt back into fork tube plug to prevent loss of oil while handling. 9. Move forks to bench area. Place suitable drain pan on floor beneath vise. 10. Repeat Steps 2-6 to remove left fork. Left And Right Fork-Disassembly 1. Remove nuts, lockwashers, flat washers and axle holder from studs at end of fork slider. 2. See Figure 2. Obtain FORK TUBE HOLDER (Part Number HD-41177) and proceed as follows: a. Clamp end of tool in vise in a horizontal position with plastic knobs facing toward you. b. See Figure 3. With the fork cap bolt topside, clamp fork tube between rubber pads on inboard side of tool. Tighten knobs until fork tube is securely held. 3. Remove fork cap bolt from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug from fork tube. Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove 6mm screw from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and discard damper tube. 12. Remove wear ring and rebound spring. Discard rebound spring. Do not expand or stretch retaining clip to remove from fork tube or clip may become bent or distorted. 13. Using pick tool, remove retaining clip between fork slider and fork tube. 14. Remove fork tube from fork slider. NOTE To overcome any resistance, use the fork tube as a slide hammer, that is, first push fork tube into fork slider and then pull it outward with a moderate amount of force. Repeat this sequence until fork tube separates from fork slider. 15. Slide fork oil seal, slider spacer and slider bushing off end of fork tube. Discard fork oil seal and slider bushing. 16. Remove the lower stop. Right and Left Fork-Assembly Exercise caution to avoid scratching or nicking fork tube. Damaging tube can result in fork oil leaks after assembly. 1. See Service Parts Illustration. Obtain new Damper Tube (Item 7, Part Number 46532-04) from kit. Obtain new Rebound Spring (Item 8, Part Number 46273-02) from kit and install on opposite end. Install wear ring removed in step 12. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube. Install lower stop at end of damper tube. 3. Install fork slider in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (14) (Part Number 45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing down fork tube. 5. Slide slider spacer down fork tube until it contacts slider bushing.

Incoming search terms:

Honda GL1000/1100 starter motor Removal/ Over haul Manual

0

Filed Under (Honda) by admin on 08-04-2011

download
1. Remove the three long bolts that hold the sections together and separate them. Be careful as there are a series of flat thrust washers on each end of the armature (located in the middle section). 2. The end cap basically performs no function other than to cover the brush plate and commutator area as well as center the armature shaft in a pressed in bushing located in the end of the cap. 3. The drive end contains the reduction gearing and if need be, can be disassembled to replace the bearing. This is extremely unlikely. The shaft should turn freely and normally only requires a cleaning and grease application. If the bearing in fact needs replacing, simply remove the “C” clips on either end, drive out the bearing and reinstall with an appropriate size replacement. Any decent auto parts / industrial supply should be able to supply the correct bearing. 4. Remove the brush plate from the end of the center section by removing the screw at the one brush connection. Before removing the brushes, note that one of them has an insulating sleeve over the braided wire. The replacement must go in the same brush holder. Remove the brushes and replace if necessary and clean the brush plate. ** Brake Cleaner is a good general cleaner for this entire job. 5. Remove the thrust washers from brush plate end of the armature. Count them and ensure they go back on the correct way. 6. The end of the center section that had the drive end on it has a circular plate covering it with a short splined shaft protruding through the plate. Drive the plate out by tapping the opposite end of the section on the shaft – just lightly with a rubber hammer or piece of wood to protect the shaft. Once the plate is out, remove the armature from the section. You will find more thrust washers at this end. Make sure they go back on correctly. 7. In the center of the center section there are four large Philips screws. These hold in the field coils found within the housing. Using an “impact driver”, loosen the four screws that go around the circumference of the center section and remove them. Remove the 10mm nut for the battery connection and the accompanying fiber insulating washers. With the screws and nut removed, the entire field coil assembly should withdraw entirely from the housing. There will be four (4) metal plates that the screws mounted into come falling out. They are easily replaced into the field coils when you slide it back into the housing. Do not be alarmed that you suddenly have four loose metal parts. 8. With everything out of the housing, thoroughly clean everything using the Brake Cleaner. Although the cleaner will dry without leaving a film, it is suggested that the components be dried with compressed air. 9. Get some extremely fine steel wool (“000″ of even “0000″ is better) and gently clean the metal surfaces or bars of the armature and the commutator. Blow with compressed air. 10. Using a volt/ohmeter, test for continuity between pairs of armature bars (the long ones). There should be continuity between the pairs around the entire circumference.

Yamaha V-Star 1100 Custom and Classic cruisers Floorboard/ Footpeg Extension Installation Instructions

0

Filed Under (Yamaha) by admin on 09-11-2010

download
Start on the right (brake) side. 1) Loosen the nut at the end of the brake rod. This will allow you to unscrew the brake rod from the brake lever clevis later. 2) Pull out the cotter pin and remove the pivot pin. Unscrew the clevis 3) Then using a 14mm socket or box-end wrench, remove the two bolts that hold the brake floorboard/footpeg assembly (whichever your bike has) to the frame. These bolts are torqued to 46 ft lbs, so this may be a bit difficult. 1. Loosen this nut 2. Remove the cotter pin (other side of this pivot pin) remove the pivot pin a unscrew the nut to remove the clevis nd 3. Remove these bolts When you remove the floorboard/footpeg bracket, be careful not to pull the brake switch wires loose. You may wish to cut the cable tie for more room, and then rest the bracket, with the footpeg or floorboard attached, on a short box, or block of wood, to keep it handy. Install the new brake rod, to the end of the existing brake rod. Re-install the pivot pin, and the pivot pin cotter pin. Installing the extension bar: Note that the extension bar is bolted so that it rises up in front. Use the new bolts to mount the floorboard/ footpeg bracket to the threaded holes in front. Install the Extension in the proper orientation (angled holes bolt up to the frame, with front of the bar higher than the rear – see photo) using the stock bolts for the extensions to the frame and the new bolts and washers supplied with the kit, on the forward threaded section to relocate the floorboard or footpeg bracket. The use of LocTite ® Blue here is recommended. At this point the right side Floorboard or Footpeg should be secured tightly and the brake lever hanging loose. Now install the Brake rod extension, threading the male end to the original brake rod. Don’t tighten this end yet Place the clevis over the forward most end of the brake rod extension, and threat the clevis nut onto the end of the rod. Bring the brake rod upright, to meet with the clevis at the end of the brake rod extension and replace the pivot pin. Before reinstalling the cotter pin, check the angle of the brake lever, to insure that you have the brake pedal where you want. If necessary, adjust the extension rod in or out, until you are satisfied, and then reinstall the cotter pin into the pivot pin. Check the Brake switch wire and install a new cable tie if required. Note: Due to utilizing a thicker material, 1/2″ versus 3/8″ from our competitor, the Brake rod is now positioned at a greater angle. Even with the angle, braking performance is not affected, but if you wish to bring the master cylinder in line with the brake rod, do this. Loosen the rear, and remove the front Allen bolt. Then place two washers behind the front bolt, under the bracket, and then re-install the bolts To change the angle of the brake rod, 1) loosen and remove the two master cylinder bracket Allen bolts 2) insert two washers behind the front bolt (front of the bike), behind the master cylinder bracket 3) tighten both bolts. Do not install any washers on the rear mounting hole. This will make the angle of the Brake Rod less aggressive. Step Two – Left Side For the left (Shifter) side, 1) use an open-end 10 mm wrench, to unscrew the two nuts that hold the shift rod in place. PLEASE note that one end of the shift rod has a left hand threaded nut. SAVE the nuts, as you will need them on the new longer Polished Stainless Steel Shift Rod. 2) Remove the stock shift rod. 3) Then using a 14mm socket or box-end wrench, remove the two bolts that hold the shifter floorboard/footpeg assembly (whichever your bike has) to the frame.

Incoming search terms:

HARLEY DAVIDSON GLOSS BLACK TRIPLE TREE COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
INSTALLATION 1. Refer to the service manual to remove the front panel, side panels and trim strips. Save all hardware to install the new panels from the kit and trim strips. 2. See Figure 1 and Table 1. Install new panels from the kit and trim strips (D). 3. Tighten screw (A), three places, to 20-30 in-lbs (2.26-3.39 Nm) Tighten screw (B), two places, to 12-17 ft-lbs (16.3-23.0 Nm) Tighten screw (C), four places, to 8-12 ft-lbs (10.8-16.3 Nm) . If installing on a motorcycle with a light bar or windshield, refer to the appropriate service manual or instruction sheet for torque values.

HARLEY DAVIDSON LOWER FORK BRACKET (TRIPLE TREE) COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
Installation 1. For models equipped with air baffle: See Figure 1. Remove and discard the two hex screws (2) and flat washers (3) holding the baffle (1) to the fork stem and bracket assembly(4). Retain the baffle for later reassembly. For models not equipped with air baffle: Remove and discard the two plugs from the rear of the fork stem and bracket assembly (4). 2. Remove and discard the hex socket head screw (6) holding the brake line manifold (5) to the underside of the fork stem and bracket assembly. 3. Place the lower fork bracket cover into position covering the brake line manifold. Attach the cover (and the baffle, if so equipped) to the fork stem and bracket assembly with the two 1/4″ self-tapping hex screws from the kit. Tighten securely. 4. Install the 5/16″ self-tapping hex socket screw through the cover and brake line manifold into the stem and bracket assembly. Torque to 10-15 ft-lbs (13.6-20.3 Nm). 5. Verify that the throttle and clutch cables are routed properly and do not interfere with steering the vehicle. After disturbing the brake system, BEFORE moving motorcycle, you must pump brake fluid until the pistons push the pads against the brake disc. If you don’t pump fluid pressure up again, the brake will not be available to stop the motorcycle which could result in death or serious injury. After disturbing the brake system, always test motorcycle brakes at low speed. If brakes are not operating properly, or braking efficiency is poor, testing at high speeds could result in death or serious injury

Installation Instructions for TRD’s 3.4-liter V6 Supercharger Kit 1997-2000 Tacoma,1997-1998 T-100, 1996-2000 4Runner

0

Filed Under (Toyota Manuals) by admin on 28-05-2011

Download

begin, TRD recommends you thoroughly Before you and engine compartment.thatyou don’t, grease clean the engine
If buildup  on parts could become dislodged during the procedure and fall into the engine.
• Make sure the engine has cooled fully before you begin. suggest you draw diagrams of your
• To help you later, we you disconnect anything. You can doengine’s cable routing before the same

for the vacuum hoses; however, some of the vacuum connections on your stock manifold may not be the same as those on the supercharger. To ensure the proper hose connections, refer to the diagrams in the back of this manual.
TRD supercharger has been designed to reuse most of • Thestock nuts and bolts.kitTherefore, as you remove them, keep the  them with their components or label them for location. This will assure a faster, easier installation.
B. Removal of Stock Intake Manifold (figure 1)
1. Disconnect the battery ground cable.
2. With tape or a permanent marker, mark the forward edge of the power steering and the air conditioning compressor drive belts (figure 2). This will ensure that the belts will be returned to their original positions and that they will rotate in the same direction. If you reverse the direction of rotation, it may cause the belts to fray.