1997 yamaha rt 100 specifications

You search Auto repair manual PDF 1997 yamaha rt 100 specifications, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1997 yamaha rt 100 specifications Direct Download speed 5282 Kb/s

  1997 yamaha rt 100 specifications Full Version speed 6162 Kb/s



Installation Instructions for TRD’s 3.4-liter V6 Supercharger Kit 1997-2000 Tacoma,1997-1998 T-100, 1996-2000 4Runner

0

Filed Under (Toyota Manuals) by admin on 28-05-2011

Download

begin, TRD recommends you thoroughly Before you and engine compartment.thatyou don’t, grease clean the engine
If buildup  on parts could become dislodged during the procedure and fall into the engine.
• Make sure the engine has cooled fully before you begin. suggest you draw diagrams of your
• To help you later, we you disconnect anything. You can doengine’s cable routing before the same

for the vacuum hoses; however, some of the vacuum connections on your stock manifold may not be the same as those on the supercharger. To ensure the proper hose connections, refer to the diagrams in the back of this manual.
TRD supercharger has been designed to reuse most of • Thestock nuts and bolts.kitTherefore, as you remove them, keep the  them with their components or label them for location. This will assure a faster, easier installation.
B. Removal of Stock Intake Manifold (figure 1)
1. Disconnect the battery ground cable.
2. With tape or a permanent marker, mark the forward edge of the power steering and the air conditioning compressor drive belts (figure 2). This will ensure that the belts will be returned to their original positions and that they will rotate in the same direction. If you reverse the direction of rotation, it may cause the belts to fray.

Incoming search terms:

1997 Honda CBR 1000 F specifications

0

Filed Under (Honda) by admin on 03-11-2010

download
Front brakes: Dual disc Rear brakes: Single disc Speed and acceleration Top speed: 255.0 km/h (158.4 mph) Power/weight ratio: 0.5745 HP/kg Other specifications Further information Parts and accessories Check out parts and accessories from our partners. Ask questions Join the 97 Honda CBR 1000 F discussion group Insurance, loans, tests Search the web for dealers, loan and insurance costs, tests, customizing, etc. Related bikes List related bikes for comparison of specs Buying a bike starts at Bikez Get a list of related motorbikes before you buy this Honda. Inspect technical data. Look at photos. Read the riders’ comments at the bike’s discussion group. And check out the bike’s reliability, repair costs, etc. Show any 1997 Honda CBR 1000 F for sale on our Bikez.biz Motorcycle Classifieds. You can also sign up for e-mail notification when such bikes are advertised in the future. And advertise your old MC for sale. Our efficient ads are free. You are also welcome to read and submit motorcycle reviews. Rating sample for this Honda bike Value for money for the 1997 Honda CBR 1000 F: (67.1 out of 100) Click here for complete rating. You can also compare bikes. Pictures, trademarks and logos of third parties are exclusive property of the respective owners. Technical specifications are subject to change without notice. Bikez.com has been developed by low-cost software development company ObjectLabs

Incoming search terms:

Sanyang JET 50/100 and JET Euro 50/100 Specifications And Service Manual

0

Filed Under (Sym) by admin on 24-11-2010

download
Carbon monoxide If you must run your engine, ensure the place is well ventilated. Never run your engine in a closed area. Run your engine in an open area, if you have to run your engine in a closed area, be sure to use an extractor. Caution Exhaust contains toxic gas which may cause one to lose consciousness and even result in death. Gasoline Gasoline is a low ignition point and explosive material. Work in a well-ventilated place, no flame or spark should be allowed in the work place or where gasoline is being stored. Caution Gasoline is highly flammable, and may explode under some conditions, keep it away from children. Used engine oil Caution Prolonged contact with used engine oil (or transmission oil) may cause skin cancer although it might not be verified. We recommend that you wash your hands with soap and water right after contacting. Keep the used oil beyond reach of children. Hot components Caution Components of the engine and exhaust system can become extremely hot after engine running. They remain very hot even after the engine has been stopped for some time. When performing service work on these parts, wear insulated gloves and wait until cooling off. Battery Caution y Battery emits explosive gases; flame is strictly prohibited. Keep the place well ventilated when charging the battery. y Battery contains sulfuric acid (electrolyte) which can cause serious burns so be careful do not be spray on your eyes or skin. If you get battery acid on your skin, flush it off immediately with water. If you get battery acid in your eyes, flush it off immediately with water and then go to hospital to see an ophthalmologist. y If you swallow it by mistake, drink a lot of water or milk, and take some laxative such as castor oil or vegetable oil and then go to see a doctor. y Keep electrolyte beyond reach of children. Brake shoe Do not use an air hose or a dry brush to clean components of the brake system, use a vacuum cleaner or the equivalent to avoid dust flying. Caution Inhaling dust may cause disorders and cancer of the breathing system. Brake fluid Caution Spilling brake fluid on painted, plastic, or rubber parts may cause damage to the parts. Place a clean towel on the above-mentioned parts for protection when servicing the brake system. Keep the brake fluid beyond reach of children

Incoming search terms:

1997 Honda CBR 1000 F specifications review

0

Filed Under (Honda) by admin on 20-12-2011

download
Front brakes: Dual disc Rear brakes: Single disc Speed and acceleration Top speed: 255.0 km/h (158.4 mph) Power/weight ratio: 0.5745 HP/kg Other specifications Further information Parts and accessories Check out parts and accessories from our partners. Ask questions Join the 97 Honda CBR 1000 F discussion group Insurance, loans, tests Search the web for dealers, loan and insurance costs, tests, customizing, etc. Related bikes List related bikes for comparison of specs Buying a bike starts at Bikez Get a list of related motorbikes before you buy this Honda. Inspect technical data. Look at photos. Read the riders’ comments at the bike’s discussion group. And check out the bike’s reliability, repair costs, etc. Show any 1997 Honda CBR 1000 F for sale on our Bikez.biz Motorcycle Classifieds. You can also sign up for e-mail notification when such bikes are advertised in the future. And advertise your old MC for sale. Our efficient ads are free. You are also welcome to read and submit motorcycle reviews. Rating sample for this Honda bike Value for money for the 1997 Honda CBR 1000 F: (67.1 out of 100) Click here for complete rating. You can also compare bikes.

Incoming search terms:

Yamaha V-Star 650 REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 10-01-2012

download
Instruction sheet 54-600 1 Front head pipe 54-600-01F 1 Rear head pipe 54-600-01R 1 Front heat shield 54-600-02F 1 Rear heat shield 54-600-02R 1 Outlaw muffler 50-103-127 1 Muffler bracket 54-600-40 1 Head flange 54-110-41 7 2″ standard hose clamps 70-100-35 2 1 3/4″ HD Hose clamp 70-100-37 2 5/16″-18 carriage bolts 70-100-10 2 5/16″-18 flange nuts 70-100-15 1 8mm x 1.25 x 25mm flange bolt for front head flange 70-100-09 2 8mm x 1.25 x 20mm bolts /muffler bracket 70-100-05 2 10mm x 1.25 x 35mm bolts 70-100-85 2 Spacer .250 x .438 x .875 50-100-74 2 8mm x 1.25 Flange nut 70-100-22
Disassembly 1. Remove both Allen bolts that hold the muffler together (Fig. 1) . Also Loosen clamp from the front muffler to front head pipe (Fig. 2) , and remove allen bolts from rear head pipe and remove in one peace carefully (Fig. 3) . Figure 1 Figure 2 Figure 3 2. Once the two mufflers are removed with the rear head pipe, remove bracket by removing two 8mm bolts as shown and remove bracket. (Fig 4) Figure 4
3. Remove spring from brake light switch to the brake rod located on the right side footrest. (Fig 5) Figure 5 4. Remove two bolts holding the footrest, and brake pedal (Fig. 6) . Carefully rest right side footrest on the floor or you can use a two by four to rest the footrest onto. Figure 6

Incoming search terms:

Yamaha XVS13AW SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 07-11-2010

download
INSTRUMENT AND CONTROL FUNCTIONS 3-1 3 EAU10460 Main switch/steering lock The main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various positions are described below. EAU10540 ON All electrical circuits are supplied with power, and the meter lighting, taillight, license plate light and position lights come on, and the engine can be started. The key cannot be removed. NOTE: The headlight comes on automatically when the engine is started and stays on until the key is turned to “OFF”, even if the engine stalls. EAU10660 OFF All electrical systems are off. The key can be removed. EAU10680 LOCK The steering is locked, and all electrical systems are off. The key can be re- moved. To lock the steering 1. Turn the handlebars all the way to the left. 2. Push the key in from the “OFF” position, and then turn it to “LOCK” while still pushing it. 3. Remove the key. To unlock the steering Push the key in, and then turn it to “OFF” while still pushing it. WARNING EWA10060 Never turn the key to “OFF” or “LOCK” while the vehicle is moving, otherwise the electrical systems will be switched off, which may result in loss of control or an accident. Make sure that the vehicle is stopped before turning the key to “OFF” or “LOCK”. 1. Push. 2. Turn. 1. Push. 2. Turn. INSTRUMENT AND CONTROL FUNCTIONS 3-2 3 EAU11003 Indicator and warning lights EAU11020 Turn signal indicator light “” This indicator light flashes when the turn signal switch is pushed to the left or right. EAU11060 Neutral indicator light “” This indicator light comes on when the transmission is in the neutral position. EAU11080 High beam indicator light “” This indicator light comes on when the high beam of the headlight is switched on. EAU11250 Oil level warning light “” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir- cuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5 seconds. If this occurs, have a Yamaha dealer check the vehicle. EAU42740 Fuel level warning light “” This warning light comes on when the fuel level drops below approximately 3.7 L (0.98 US gal) (0.81 Imp.gal). When this occurs, refuel as soon as possible. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, and then go off, have a Yamaha dealer check the electrical circuit. NOTE: The vehicle must be on a level surface and positioned upright, otherwise the fuel level warning light may not come on and go off at the appropriate times. This model is also equipped with a self-diagnosis device for the fuel level detection circuit. If the fue

Yamaha XV 1900A SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 07-11-2010

download
INSTRUMENT AND CONTROL FUNCTIONS 3-8 3 NOTE: Make sure there are no other immobilizer keys close to the main switch, and do not keep more than one immobilizer key on the same key ring! Immobilizer system keys may cause signal interference, which may prevent the engine from starting. 2. If the engine starts, turn it off and try starting the engine with the standard keys. 3. If one or both of the standard keys do not start the engine, take the vehicle, the code re-registering key and both standard keys to a Yamaha dealer and have the standard keys re-registered. If the odometer/tripmeter/clock display indicates any error codes, note the code number, and then have a Yamaha dealer check the vehicle. CAUTION: ECA11590 If the display indicates an error code, the vehicle should be checked as soon as possible in order to avoid engine damage. Brightness control mode The brightness can be adjusted for the following: the multi-function meter unit panel (item number “1″) the LCD (item number “2″) the speedometer, tachometer, and the fuel gauge needles (item number “3″) Select the brightness control mode as follows. 1. Turn the key to “OFF”. 2. Push and hold the “SELECT” switch. 3. Turn the key to “ON”, and then release the “SELECT” switch after five seconds. Item number “1″ is displayed. 4. Adjust the multi-function meter unit panel brightness level by pushing the “RESET” switch. 5. Push the “SELECT” switch to select the LCD. Item number “2″ is displayed. Adjust the LCD brightness level by pushing the “RESET” switch. 1. Multi-function meter unit panel 2. LCD 3. Speedometer needle 4. Tachometer needle 5. Fuel gauge needle 1. Multi-function meter unit panel 2. Item number 3. Brightness level INSTRUMENT AND CONTROL FUNCTIONS 3-9 3 6. Push the “SELECT” switch to select the speedometer, tachometer, and the fuel gauge needles. Item number “3″ is displayed. Adjust the brightness level of the speedometer, tachometer, and the fuel gauge needles by pushing the “RESET” switch. 7. Push the “SELECT” switch. The odometer/tripmeter/clock display will return to the prior mode.

YAMAHA MOTOR CORPORATION, U.S.A. STREET & ENDURO MOTORCYCLE LIMITED WARRANTY

0

Filed Under (Yamaha) by admin on 27-12-2011

download
GENERALEXCLUSIONS from this warranty shall include any failures caused by: a. Competition or racing use. b. Installation of parts or accessories that are not qualitatively equivalent to genuine Yamaha parts. c. Abnormal strain, neglect, or abuse. d. Lack of proper maintenance. e. Accident or collision damage. f. Modification to original parts. g. Damage due to improper transportation. SPECIFIC EXCLUSIONS from this warranty shall include parts replaced due to normal wear or routine maintenance. THE CUSTOMER’S RESPONSIBILITY under this warranty shall be to: 1. Operate and maintain the motorcycle as specified in the appropriate Owner’s Manual. 2. Give notice to an authorized Yamaha motorcycle dealer of any and all apparent defects within ten (10) days after discovery, and make the machine available at that time for inspection and repairs at such dealer’s place of business. You may locate your nearest authorized Yamaha dealer through your local telephone directory. WARRANTY TRANSFER: To transfer any remaining warranty from the original purchaser to any subsequent purchaser, it is imperative that the machine be inspected and registered for warranty by an authorized Yamaha motorcycle dealer. In order for this warranty to remain in effect, this inspection and registration must take place within ten (10) days after transfer. Areasonable dealer imposed fee may be charged for the inspection. In no case will warranty be extended beyond the original period. EMISSIONS CONTROLSYSTEM WARRANTY Yamaha Motor Corporation, U.S.A. also warrants to the ultimate purchaser and each subsequent purchaser of each Yamaha motorcycle covered by this warranty with a displacement of 50cc or greater, that the vehicle is designed, built, and equipped so as to conform at the time of sale with all U.S. emissions standards applicable at the time of manufacture and that it is free from defects in materials and workmanship which would cause it not to meet these standards within the periods listed immediately below. Failures other than those resulting from defects in material or workmanship which arise solely as a result of owner abuse and/or lack of proper maintenance are not covered by this warranty.

Incoming search terms:

YAMAHA YZF-R125 SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 25-11-2010

download
Fuel tank cap To remove the fuel tank cap 1. Open the fuel tank cap lock cover. 2. Insert the key into the lock and turn it 1/4 turn counterclockwise. The lock will be released and the fuel tank cap can be removed. To install the fuel tank cap 1. Push the fuel tank cap into position with the key inserted in the lock. 2. Turn the key clockwise to the original position, and then remove it. 3. Close the lock cover. NOTE: The fuel tank cap cannot be installed unless the key is in the lock. In addition, the key cannot be removed if the cap is not properly installed and locked. WARNING EWA11140 Make sure that the fuel tank cap is properly installed before riding. EAU13211 Fuel Make sure that there is sufficient fuel in the tank. Fill the fuel tank to the bottom of the filler tube as shown. WARNING EWA10880 Do not overfill the fuel tank, otherwise it may overflow when the fuel warms up and expands. Avoid spilling fuel on the hot en- gine. 1. Fuel tank cap lock cover 2. Unlock. 1. Fuel tank filler tube 2. Fuel level
INSTRUMENT AND CONTROL FUNCTIONS 3-8 3 CAUTION: ECA10070 Immediately wipe off spilled fuel with a clean, dry, soft cloth, since fuel may deteriorate painted surfaces or plastic parts. EAU43420 CAUTION: ECA11400 Use only unleaded gasoline. The use of leaded gasoline will cause severe damage to internal engine parts, such as the valves and piston rings, as well as to the exhaust system. Your Yamaha engine has been designed to use premium unleaded gasoline with a research octane number of 95 or higher. If knocking (or pinging) occurs, use a gasoline of a different brand. Use of unleaded fuel will extend spark plug life and reduce maintenance costs. EAU13442 Catalytic converters This vehicle is equipped with catalytic converters in the exhaust system. WARNING EWA10860 The exhaust system is hot after operation. Make sure that the exhaust system has cooled down before doing any maintenance work. CAUTION: ECA10700 The following precautions must be observed to prevent a fire hazard or other damages. Use only unleaded gasoline. The use of leaded gasoline will cause unrepairable damage to the catalytic converter. Never park the vehicle near possible fire hazards such as grass or other materials that easily burn. Do not allow the engine to idle too long.

Incoming search terms:

Yamaha YZF R1 SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 07-11-2010

download
INSTRUMENT AND CONTROL FUNCTIONS 3-1 3 EAU10460 Main switch/steering lock The main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various positions are described below. EAU10600 ON All electrical circuits are supplied with power, the meter lighting, taillight, license plate light, auxiliary lights and position lights come on, and the engine can be started. The key cannot be re- moved. NOTE: The headlights come on automatically when the engine is started and stay on until the key is turned to “OFF”, even if the engine stalls. EAU10660 OFF All electrical systems are off. The key can be removed. EAU10680 LOCK The steering is locked, and all electrical systems are off. The key can be re- moved. To lock the steering 1. Turn the handlebars all the way to the left. 2. Push the key in from the “OFF” position, and then turn it to “LOCK” while still pushing it. 3. Remove the key. 1. Push. 2. Turn. INSTRUMENT AND CONTROL FUNCTIONS 3-2 3 To unlock the steering Push the key in, and then turn it to “OFF” while still pushing it. WARNING EWA10060 Never turn the key to “OFF” or “LOCK” while the vehicle is moving, otherwise the electrical systems will be switched off, which may result in loss of control or an accident. Make sure that the vehicle is stopped before turning the key to “OFF” or “LOCK”. EAU11003 Indicator and warning lights EAU11030 Turn signal indicator lights “” and “” The corresponding indicator light flashes when the turn signal switch is pushed to the left or right. EAU11060 Neutral indicator light “” This indicator light comes on when the transmission is in the neutral position. EAU11080 High beam indicator light “” This indicator light comes on when the high beam of the headlight is switched on. EAU11250 Oil level warning light “” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir- cuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction

Incoming search terms: