1998 toyota camry heat shield

You search Auto repair manual PDF 1998 toyota camry heat shield, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1998 toyota camry heat shield Direct Download speed 5282 Kb/s

  1998 toyota camry heat shield Full Version speed 6162 Kb/s



HARLEY DAVIDSON SPORTSTER BLACK EXHAUST HEAT SHIELDS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-02-2011

download
INSTALLATION Remove Original Equipment (OE) Heat Shields Avoid contact with exhaust system and wear protective clothing that completely covers legs while riding. Exhaust pipes and mufflers get very hot when engine is running and remain too hot to touch, even after engine is turned off. Failure to wear protective clothing could result in burns or other serious injury. (00009a) 1. Allow the motorcycle to cool. 2. Identify the position of the OE clamp screws securing the black heat shields to the exhaust pipes. NOTE The clamp screws are positioned on either side of the exhaust pipe for clearance. 3. See Figure 1. Open the heat shield clamps (1) and spread the bands to remove front and rear heat shields (2) from the exhausts. Retain the heat shield clamps Install Black Heat Shields 1. See Figure 2. Matching the OE position of the heat shield clamps, open the clamps bands and thread the bands through the brackets of the front (1) and rear (2) black heat shields. 2. Spread the band around the exhaust pipes and push the end of the bands to engage the clamp screws. Tighten to hold the heat shields in place. 3. Adjust the shields and heat shield clamps to access clamp screws and to avoid contact with other components. 4. Tighten the heat shield clamp screws

Incoming search terms:

YAMAHA V-STAR 1300 exhaust system INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Install the bracket (Stamped 439-P, supplied) to the motorcycle chassis using the 10 x 20mm hex head bolt (supplied) and two of the stock mount bolts in the bottom holes (Figure 3). 2. Remove exhaust system and heat shields from protective packaging and place them on a non-abrasive surface such as a blanket or carpet. Using a non-permanent marker or tape, mark outside edge of each heat shield to show location of mounting clips that the hose clamps will loop through (Figure 4). 3. Apply a small amount of anti-seize compound to the threads of the stock O2 sensor and install it into the header assembly. NOTE: Be careful not to overtighten or get anti-seize compound on the sensor tip as this could damage or affect the sensor function. 4. Carefully lay header assembly into the heat shields and loosely install the hose clamps #20 on head pipe heat shields and #24 on collector heat shield (supplied) by feeding the tail end of the clamp into the heat shield clips. Take note of screw head direction (Figure 5), for adjustment purposes they must be accessible when system is installed. NOTE: Do not tighten the clamps at this time. 5. Using stock dome nuts, carefully install system into exhaust ports. (Assistance may be required). NOTE: Install but do not tighten the exhaust nuts at this time. 6. Remove the muffl er heat shield and baffl e assembly from their protective packaging. Place them on a non-abrasive surface such as a blanket or carpet. 7. Insert the large hose clamp (#56, supplied) into the clip on the muffl er heat shield. 8. Carefully slide the baffl e assembly (without damaging the fi berglass packing) into the muffl er heat shield and align the holes in the heatshield with those in the baffl e. Secure the baffl e with the 1/4-20 x 1/2″ button head screws (supplied) and tighten the hose clamp. 9. Install the 5/16″ x 1 1/4″ hex head bolt, washers and locknut (supplied) in the muffl er clamp (supplied) and slip the clamp over the end of the baffl e tube. 10. Slide nut plate (supplied) inside the bracket welded to backside of baffl e (Figure 6). 11. Install the muffl er assembly onto the collector, making sure it slides forward enough to align the edge of the bracket welded to the baffl e with the edge of the mounting bracket. 12. Attach the muffl er assembly to the mounting bracket using the 5/16″ x 5/8″ fl ange head bolts (supplied). 13. Tighten exhaust port nuts evenly on both cylinders. 14. Tighten the muffl er clamp and the 5/16″ fl ange head bolts, securing the muffl er assembly. 15. Insert the O2 sensor plug back into harness and tuck harness back into its original position. Reinstall the cover. 16. Check alignment of heat shields making sure the ends meet squarely to the collector heat shield. Tighten the hose clamps on all the heat shields when properly aligned. 17. Reinstall right side passenger and rider fl oorboards and tighten the 12mm bolts. 18. Check for adequate clearance between all exhaust system components and motorcycle accessories prone to heat damage. 19. All hardware must be properly tightened and the exhaust pipes thoroughly clean before starting motorcycle

KAWASAKI VULCAN 700/750 CRUZER EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 28-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Place the bike on the center stand. 2. Remove the three clamps attaching the heat shield to the left hand head pipe and set the heat shield aside. 3. Remove the two heat shield clamps attaching the heat shield to the right hand head pipe and set the heat shield aside. 4. Loosen the pinch clamps where the mufflers slip onto the muffler box (the black box in front of the rear tire). Remove the bolt attaching the mufflers to the footrest. 5. Remove the left and right hand mufflers and set them aside. 6. Remove the right hand foot rest and brake pedal assembly from the frame. 7. Loosen the pinch clamps where the head pipes slip into the muffler box. 8. Remove the two nuts that secure the right head pipe to the cylinder head. Repeat this step on the left head pipe and save the nuts for reuse. 9. Remove the left and right hand head pipes. Remove the header flange from each head pipe and save the two flanges for reuse. Set the head pipes aside. 10. Remove the two bolts (one on each side) that mount the muffler box to the frame. Lower the muffler box down and set it aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Remove the two bolts from the charcoal canister mount, the canister is located in front of the rear tire. Using the two 6mm x 16mm bolts (supplied) install the centerstand stop bracket, (stamped 205), by aligning the holes in the bracket with the holes in the canister mount. Be sure the bend closest to the holes in the bracket angles towards the rear of the motorcycle and the tang is pointed to the left hand side. Tighten the two 6mm bolts at this time. 2. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the front head pipe into the heat shield, wrap the hose clamp around the head pipe and give the screw three to four turns. Repeat this step with the rear heat shield. Note : The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. Leave them loose at this time. 3. Install a three hole mounting bracket to each muffler as shown in figure 1. Slide one dog bone shaped nut plate under the bracket that is welded to the backside of each muffler. Attach the mounting bracket using two of the 5/16″ flange head bolts (supplied), leave them loose at this time. Note : The muffler bracket stamped #284 is for the right hand muffler, bracket #285 is for the left hand muffler. 4. Install the rear exhaust assembly, with the heat shield attached, to the rear cylinder using the stock flanges and nuts. Install the stock muffler mounting bolts through the rear footrest brackets, the supplied muffler brackets, and finger tighten the nuts. Leave them loose at this time. 5. Repeat step #4 with the front head pipe

KAWASAKI VULCAN 900 SLASH CUT STAGGEREDS INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 02-05-2012

download
1. Attach mounting bracket 440-P to frame using two stock fl ange head bolts used on stock upper bracket (Figures 1 and 2). 2. Remove head pipes and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark outside edge of each heat shield to show location of mounting clips that hose clamps will loop through (Figure 3). 3. Lay front header, and rear header into their head heat shields and muffl er body heat shields. 4. Install #20 hose clamps (supplied) on heat shields and #36 (supplied) on muffl er body heat shields by feeding tail end of clamps into heat shield clips (fi gure 3). Take note of clamp screw head direction (Figure 4). Screw heads must be accessible when system is installed on motorcycle for adjustment purposes. NOTE: Do not tighten at this time. 5. Using stock fl ange nuts, carefully install head pipes into exhaust ports. Assistance may be required. NOTE: Do not tighten at this time. 6. Slide nut plates inside bracket that is welded to backside of muffl er bodies (Figure 5). While holding nut plates in place, attach muffl er bodies to mounting bracket 440-P using two 5/16″x 5/8″ fl ange head bolts (supplied). Leave them loose at this time. 7. Align muffl er bodies so they are level and parallel when viewing from the right side of the bike. Tighten cylinder port exhaust fl ange nuts on front and rear cylinders. 8. Tighten the fl ange bolts on both muffl ers. 9. Tighten all heat shield clamps. 10. Check for adequate clearance of all exhaust system components and motorcycle accessories prone to heat damage. NOTE: For models with fl oorboards, two Spacer washers are supplied to space out the fl oorboard bracket enough to allow the fl oorboard to fold up without hitting the heat shield. 11. Be sure to tighten all hardware before starting your motorcycle. 12. After installation and before starting motorcycle, completely clean pipes and muffl ers with cleaning solvent and a clean, soft cloth that will not leave a residue. NOTE: Any residue, oil, or fi ngerprints will stain the chrome when the metal heats up

Incoming search terms:

1998 Toyota Camry LE Sedan L4-2164cc 2.2L DOHC MFI REMOVAL

0

Filed Under (Toyota Manuals) by admin on 21-06-2011

Download
Remove the 2 bolts holding the support stay to the support bracket.
b. Remove the 2 bolts holding the support bracket to the front frame.
c. Remove the 2 bolts and 2 nuts holding the front exhaust pipe to the
center exhaust pipe.
d. Remove the 3 nuts holding the front exhaust pipe to the exhaust manifold.
e. Remove the front exhaust pipe and 2 gaskets

KAWASAKI VULCAN 1500 PRO PIPE HS EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 28-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the mufflers by loosening the pinch clamps on the front of each muffler. 2. Remove the muffler mounting bolt from the right side passenger footrest, slide the mufflers off and set them aside. Note: Save the mounting bolt, it will be reused for installation. 3. Loosen the pinch clamp on both front and rear head pipes, they’re located at the resonance chamber (the black box where the pipes meet). 4. Remove the two acorn nuts that mount the head pipe to the cylinder head. Remove the two piece header flange and set it aside. 5. Remove the front head pipe by rotating it down and pull it out of the resonance chamber. 6. Remove the two acorn nuts and flange from the rear head pipe. Remove the two bolts from either side of the resonance chamber and lower rear pipe and resonance chamber down and out and set it aside. 7. Remove the rubber grommets at the resonance chamber mounting points. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Install the new mounting bracket (stamped 317) to the inside of the stock muffler mounting point (Refer to FIG. 1). 2. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edge of all three heat shields with the location of the mounting clips that are welded to the backside. Position the front heat shield over the head pipe and feed the tail end of the hose clamps into the clips. Be sure that each hose clamp is engaged with both clips. Repeat this step with the rear and collector heat shields. To facilitate the installation of the collector heat shield use a forward sliding motion from the rear of the collector. Do not force the collector heat shield directly onto the collector as damage to the heat shield will result. Note: the collector heat shield uses the 3/8″ wide clamps. 3. Rotate the hose clamps in the shields so that the screw drives are accessible. Tighten only finger tight at this time. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 4. Check to be sure that the stock exhaust gaskets are in good shape. If you have any doubts as to their condition, replace them. 5. Install the header with the heat shields attached, to the front and rear cylinders using the stock nuts and bolts. Leave them loose at this time. 6. Slide the chrome muffler clamp (supplied) onto the inlet end of the megaphone. Install the 5/16″ x 1 1/4″ bolt with a flat washer on either side of the clamp followed by the 5/16″ lock nut (hardware supplied). Leave the clamp loose at this time. 7. Slip the megaphone onto the head pipe collector, engaging the collector heat shield between the clamp and the outer slip joint tube. Slide one dog bone shaped nut plate under the bracket that

Incoming search terms:

FLUID SPECS MODEL- YEAR 1994- 2005 FOR TOYOTA CAMRY, COROLLA AND TACOMA

0

Filed Under (Toyota Manuals) by admin on 17-09-2011

Download
Toyota Genuine Motor Oil 5W-30 Toyota Genuine Motor Oil 10W-30 Ethylene-Glycol Antifreeze Toyota Long Life Coolant Toyota Super Long Life Coolant 00272-SLLC2 Hypoid API GL-5 75W-90 Gear Lube T-IV Transmission Fluid ATF WS Transmission Fluid 08885-80306 Good brand of 80W-90 gear lube Hypoid API GL-5 80W-90 Gear Lube Castle V160 Gear Lube Sequential Manual Transmission Fluid 08885-01306 08886-02206 Synthetic Hypoid API GL-5 75W-140 Gear Lube Limited Slip Gear Oil

Incoming search terms:

HARLEY DAVIDSON SPLASH SHIELD KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
This kit is designed to fit 1980 – 1983 and 1988 and later FLHT and 1994 and later FLHR models without fairing low- ers. installation 1. Locate splash shield for left side. Bar and Shield should face forward and opening in splash shield should be on right side. 2. Slip splash shield on left side of engine guard. 3. An opening in the outer edge of the splash shield allows the splash shield to fit over highway footrests. 4. Place the wide attaching strap around the frame down- tube, do not put strap over clutch cable. 5. Slip buckles on attaching strap onto mating buckle halves attached to back side of splash shield. Latches will snap into locked position when buckle is properly closed. 6. Adjust the fit by lifting the Velcro®attached straps (on rear of splash shield) and changing length as required. 7. Repeat procedure for right side of vehicle. NOTE If splash shields cover amber reflectors mounted on frame down tubes, install reflectors included in kit as follows: 8. See Figure 1. Clean areas on both sides of fender (1) where amber reflectors are to be mounted. 9. Remove backing paper from rear of reflector and place reflectors in position (2). Federal Motor Vehicle Safety Standard (FMVSS) 108 requires motorcycles to be equipped with rear and side reflectors. Be sure rear and side reflectors are properly mounted. Low visibility of rider can result in death or serious injury. (00336a) NOTE To remove splash shields depress both latches with thumb and forefinger and gently pull buckle apart. Open remaining buckle and slide splash shield off engine guard

2009 VULCAN 1700 HEAT SHIELD KITS INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Installation Procedure Refer to the appropriate sections of the Service Manual for information and procedures related to parts removal and installation. NOTE: Cover the frame with tape on the left and right o sides (right side shown, left side similar) to prevent scratches during shield installation Remove and discard upper left and upper • right radiator screen mount screws (right side shown, left side similar). Install the heat shield along the upper edge • of the radiator and attach the shield and the screen with the radiator screen mount screws provided in the kit Remove the tape from the frame rails. • Install the clutch hose in the clamp on the left • frame tube. Front Cylinder Exhaust Cover NOTE: Apply penetrating oil to the exhaust cover o clamp screws prior to loosening. Loosen the exhaust pipe cover clamp screws. • Remove and discard the exhaust cover. •

HARLEY DAVIDSON SOFTAIL FATBOY STRAIGHTSHOT HS SLIP ON INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 24-12-2010

download
1. Remove the heat shield from the rear head pipe and the back heat shield (“Z” Shaped) off the lower head pipe. NOTE: Loosen the front heat shield hose clamp closest to this shield to facilitate its removal. 2. Loosen the clamps holding the muffl ers onto the head pipes. 3. Remove the 1/2″ bolts holding muffl ers onto support bar. 4. Slide both muffl ers towards the rear until they are free from the head pipes. NOTE: Assistance and the use of a penetrating lubricant may be required. 5. Remove the stock exhaust clamps from the nose of each muffl er (these will be re-used when installing the new system). QUIET BAFFLE FUELPAK VANCE & HINES EXHAUST SYSTEM INSTALLATION WHEN YOU KNOW THE DIFFERENCE 1. Using the 5/16″ x 3/4″ hex head bolts and washers (supplied) secure the mounting bracket (stamped 419-P)(supplied) to the stock muffl er support bar. NOTE: The bracket should be mounted with the notch facing the front of the motorcycle (Figure 1). 2. Remove muffl ers and heat shields from their protective packaging and place them on a non-abrasive surface such as a blanket, towel or carpet. 3. Carefully lay a muffl er assembly into each straight heat shield and loosely install the hose clamps (supplied) by feeding the tail end of the clamp into the heat shield clips. Note the direction of the screw heads with relation to the muffl er location (Figure 2). 4. Slide stock exhaust clamps onto the nose of each muffl er body. NOTE: Orient the clamp to enable access for tightening the nut after installation. 5. Slide upper muffl er assembly (with heat shield) onto the upper head pipe. Insert nut plate (supplied) into the bracket welded to the muffl er body (Figure 3) and secure to the mounting bracket using the 5/16″ x 5/8″ fl ange head bolts (supplied). 6. Repeat step 5 placing the lower muffl er assembly on the lower head

Incoming search terms: