1999 kawasaki kaf620 a5 2510 wiring diagram

You search Auto repair manual PDF 1999 kawasaki kaf620 a5 2510 wiring diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1999 kawasaki kaf620 a5 2510 wiring diagram Direct Download speed 5282 Kb/s

  1999 kawasaki kaf620 a5 2510 wiring diagram Full Version speed 6162 Kb/s



1999-2004 Kawasaki 1500 Drifter Power Commander Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1 Remove the seat. 2 Remove the left side cover. 3 Remove the speedometer assembly. 4 Unbolt the fuel tank. NOTE: It is not necessary to remove the fuel tank. It does however make the installation easier. If you do remove the tank, pay attention to the vent hose routing. Pressing the tabs on the black fuel line connector will allow the fuel line to be disconnected (Fig. A) 5 Remove the battery/ECU hold down bracket (Fig. B). 6 Unbolt and move the bank angle (tip over) sensor out of the way (Fig. C). Fig. A Fig. B Fig. C i201-411 www.powercommander.com 1999-2004 Kawasaki 1500 Drifter – PCIII USB – 2 Bank angle sensor (tip over switch) Remove these 2 bolts 7 Loosen the bolts holding the plastic tray on the left side of the bike (under the left side cover) (Fig. D). 8 Route the wire from the PCIII behind the plastic tray and under the frame side rail (Fig. E). 9 Retighten the bolts holding the plastic tray. 10 Continue routing the wires from the PCIII under the frame near the lower fuel tank mount and go up to the throttle body area (Fig. F). Fig. D Fig. E Fig F i201-411 www.powercommander.com 1999-2004 Kawasaki 1500 Drifter – PCIII USB – 3 Route PCIII harness between plastic tray and frame Route wires under frame Loosen these bolts 11 Disconnect the injector connector from the rear injector (Fig. H). 12 Plug the female PCIII connector with ORANGE/WHITE wire onto the rear injector (Fig. H). 13 Connect the male PCIII connector with ORANGE wire onto the stock injector connector (Fig. H). 14 Repeat steps 11 thru 13 for front injector using the PCIII connectors with the YELLOWcolored wires. 15 Locate the wires coming from the throttle position sensor. (Fig. H). The throttle position sensor is located on the right hand side of the throttle body. It is between the frame and engine

Incoming search terms:

SUZUKI SV 1000 RADIATOR (COOLING SYSTEM) SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
FI SYSTEM MALFUNCTION CODE AND DEFECTIVE CONDITION MALFUNCTION CODE DETECTED ITEM DETECTED FAILURE CONDITION CHECK FOR COO NO FAULT C11 Camshaft position sen- sor The signal does not reach ECM for more than 3 sec . after receiving the starter signal . The camshaft position sensor wiring and mechanical parts (Camshaft position sensor, intake cam pin, wiring/coupler con- nection) C12 Crankshaft position sensor The signal does not reach ECM for more than 2 sec . after receiving the starter signal . The crankshaft position sensor wiring and mechanical parts (Crankshaft position sensor, wiring/coupler connection) C13 Intake air pressure sensor The sensor should produce following voltage . (0.50 V < sensor voltage < 4 .85 V) Without the above range, C13 is indicated. Intake air pressure sensor, wiring/coupler connection C14 Throttle position sen- sor The sensor should produce following voltage . (0.20 V < sensor voltage < 4 .80 V) Without the above range, C14 is indicated. Throttle position sensor, wiring/coupler connection C15 Engine coolant temperature sensor The sensor voltage should be the following. (0.15 V <_ sensor voltage < 4 .5 V) Without the above range, C15 is indicated. Engine coolant temperature sensor, wiring/coupler connection C21 Intake air temperature sensor The sensor voltage should be the following. (0.15 V < sensor voltage < 4 .5 V) Without the above range, C21 is indicated. Intake air temperature sensor, wiring/coupler connection C22 Atmospheric pressure sensor The sensor voltage should be the following. (0.50 V < sensor voltage < 4 .5 V) Without the above range, C22 is indicated. Atm. pressure sensor, wiring/coupler connection C23 Tip over sensor The sensor voltage should be the following for more than 2 sec . after ignition switch turns ON . (0 .20 V < sensor voltage < 4 .80 V) Without the above value, C23 is indicated. Tip over sensor, wiring/coupler connection C24 or C25 Ignition signalCrankshaft position sensor signal is produced and ECM determines the ignition signal but signal from ignition coil is interrupted continuous by 4 times or more. In this case, the code C24 or C25 is indicated. Ignition coil, wiring/coupler connection, power supply from the battery SERVICING INFORMATION 8 .3 C28 Secondary throttle valve actuator No operating voltage is supplied from the ECM, C28 is indicated. STVA can not operate. STVA lead wire/coupler, STVA C29 Secondary throttle valve position sensor The sensor should produce following voltage . (0.10 V < sensor voltage < 4 .90 V) Without the above range, C29 is indicated . Secondary throttle position sensor, wiring/coupler connection C31 Gear position signalGear position signal voltage should be higher than the following for more than 2 seconds. (Gear position switch voltage >_ 0 .6 V) Without the above value, C31 is indicated. Gear position sensor, wiring/coupler connection, gearshift cam, etc. C32 or C33 Fuel injector Crankshaft position sensor signal is produced and ECM determines the injection signal but fuel injection signal is interrupted continuous by 4 times or more. In this case, the code C32 or C33 is indicated. Injector, wiring/coupler connection, power supply to the injector C41 Fuel pump relay No voltage is applied to fuel pump although fuel pump relay is turned ON, or voltage is applied to fuel pump although fuel pump relay is turned OFF . Fuel pump relay, connecting lead, power source to fuel pump relay C42 Ignition switchIgnition switch signal is not input in the ECM . Ignition switch, lead wire/coupler C44 Heated oxygen sensor (HO2S) [For E-02, 19] During 02 feedback control, 02 sensor voltage is higher or lower than the specification . No signal is detected during engine operation or no electrical power is supplied from the battery . HO2S lead wire/coupler connection Battery voltage supply to the HO2S C49 PAIR control solenoid valve (PAIR valve) When no operating voltage is supplied from the ECM, C49 is indicated. PAIR valve can not operate. PAIR valve lead wire/coupler

Incoming search terms:

Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Upgrading the Suspension on the Kawasaki ER6-F/ N

0

Filed Under (Kawasaki) by admin on 30-11-2010

download
Top fork is as removed. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Before removing the fork from the clamps on the yokes I loosened the fork top. Before removing the fork top the fork-slider was placed in a vice and the bottom bolt loosened….. … before finally being removed with the fork upside down. Because the springs were still in situ this gave sufficient tension on the damper-rod to prevent it from turning and allow the bolt to be removed. When I turned the fork the right-way up to remove the fork-top I did it over a container to catch the oil. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource All the OE components that will no longer be required. Left to right. Fork-top, spacer tube, washer, spring, damper-rod. Bottom bolts get re-used. Old and new, laid-out for comparison. The damper unit, minus spring and fork-top, drops inside the stanchion and slider. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Then the bolt goes back in, as tight as possible, to secure it. Top fork is done, second one awaits. Note the spring seat on the right, just below the spring. This drops over the damping rod after the oil has been added. The small locking-nut screws over the threaded part of the damping-rod next, all the way to the bottom. Spring drops in and then the fork-top screws on to the damping-rod as well, all the way down to the lock-nut which is used to secure it. At this point the stanchion is extended to the fork-top which is screwed in. Job done.

Incoming search terms:

1992 Toyota Cressida Vehicle Wiring Chart and Diagram

0

Filed Under (Toyota Manuals) by admin on 18-06-2011

Download
Listed below is the vehicle specific wiring diagram for your car alarm, remote
starter or keyless entry installation into your 1992 Toyota Cressida . This
information outlines the wires location, color and polarity to help you identify the
proper connection spots in the vehicle. Please be sure to test all of your wires
with a digital multimeter before making any connections. More information on
using a multimeter and testing wires please see our Technical Support Area.

Incoming search terms:

Kawasaki Exhausts – ZX-6 ZX-10 Zx-14 Exhaust – Slip-ons INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Our favorite exhaust options for Kawasaki ZX Ninjas – ZX-10,ZX-6r, and the new horsepower king, Zx-14.. Grab your horsepower today. We love Rob Muzzy and Muzzy Exhausts.Going back to Doug Chandler and Scott Russell, Muzzy has been synonomous with Kawasaki and performance – and for years, if you rode Kawasaki,and you were on the podium, Muzzy was on your exhaust. We also feature Arrow and Yoshimura exhausts for your ZX-6R, ZX-10 and ZX-14. We love the sound of a Yosh exhaust on any Kawasaki Ninja. Yoshimura Oval (RS-3) Race Slip-On for Kawasaki ZX14R 2006 The easiest and least expensive way to experience Yoshimura performance is with our Slip-On/Bolt-On lines. Bolt-On style bolts to the O. E. M. mid-pipe Slip-On style with its stainless steel easily attaches to the mid-pipe RS-1 is available where noted Usually, no jetting or re-programming is required and installation is a snap Hindle Stainless Exhaust High Head Pipes – Kawasaki ZX6R-RR 03-04 The worlds lightest stainless steel exhaust system. Increase horsepower and torque throughout the entire rpm range. Lightweight, strong stainless steel header design looks great and weighs less than stock headers. Available in low- and high-mo North Denver News http://northdenvernews.com Powered by Joomla! Generated: 19 October, 2010, 12:28 Hindle Stainless Exhaust Low Head Pipes – Kawasaki ZX9R 00-03 The worlds lightest stainless steel exhaust system. Increase horsepower and torque throughout the entire rpm range. Lightweight, strong stainless steel header design looks great and weighs less than stock headers. Available in low- and high-mo

Incoming search terms:

2005 Kawasaki ZX6R Power Commander Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the tail section by removing the undertail and removing the six screws for the tail section. 2 Prop the front of the fuel tank up. 3 Lay the PCIIIin the tail section and route theharness along side the stock wiring harness towards the throttle bodies (Fig. B&C). Fig. A Fig. B Fig. C 2005 Kawasaki ZX6R – PCIII USB – 2 i218-411 www.powercommander.com PCIII harness PCIII harness Remove these screws 4. Disconnect the stock wiring harness from the LOWERinjectors at the throttle bodies (Fig. D). 5. Plug the PCIII connectors in-line of the stock injectors and wiring harness. ORANGE – cylinder 1 YELLOW- cylinder 2 GREEN – cylinder 3 BLUE – cylinder 4 6. Locate the Throttle Position Sensor connector behind the throttle bodies. This is a WHITE 3 pin connector (Fig. F) Fig. D Fig. E Fig F 2005 Kawasaki ZX6R – PCIII USB – 3 i218-411 www.powercommander.com PCIII connectors TPS connector Disconnect Stock connectors 7. Plug the PCIII harness in-line of the stock wiring harness (Fig. G). 8. Attach the ground wire from the PCIII to the negative side of the battery (Fig. H)

Incoming search terms:

HARLEY-DAVIDSON 5 Speed Transmissions 1984 – 1999 EVO / 5 Speed & 1999 – 2006 Twin Cam Installation Instructions

0

Filed Under (Harley Davidson) by admin on 26-11-2010

download
Remove Original Parts From Vehicle. 2.1 Obtain a small tube of Loctite® #262 (red) for use later. 2.2 Drain the transmission oil. 2.3 Remove the clutch adjustment cover (left side). 2.4 Remove rear exhaust header pipe (cross over exhaust pipe). 2.5 Remove the muffler support bracket. 2.6 Remove the clutch release cover (right side). 2.7 Remove clutch push rod and oil slinger. To be disassembled and modified later. 2.8 Remove the two nuts from the main (rear) and counter (front) transmission shafts. 2.9 Remove the transmission bearing housing (puller available from Champion Sidecars). To be replaced with new reverse gear transmission bearing housing (Trap Door). 2.10 Cover the exposed gears in the transmission with a cloth in preparation to cut the shifter fork shaft. 3 Install New Main and Countershaft Gears NOTE: Gears and Tapered Split Rings are factory matched sets. Do not mix!. 3.1 Locate the shifter fork rod, mark fork rod flush at transmission case and pull out 1/4″. Figure 1 3.2 Cut the shaft at the mark and push it back in. The shaft end MUST NOT stick out of the transmission case. If the shaft is in deeper, fill the hole with silicone to prevent the shaft from moving in and out. NOTE: Shifter fork is made of non-tempered metal and may be cut with a hacksaw or Dremel® cutting tool. 3.3 Important: Remove stock spacers from main and counter shafts. Spray with silicon remover (Brake-Clean) then, using supplied cleaning pad, clean shafts, new counter and main shaft gears and tapered lock rings (inside and outside) Figure 1 3.4 With motorcycle in neutral, pull both the shafts out and simultaneously push the OEM outermost gears in until seated completely to expose the shoulders of both shafts. The countershaft shoulder should be flush with the gear face. For the main shaft the gear would “hang over” the shoulder a small bit. Figure 2 3.5 Apply supplied Champion Super-Lock retaining compound to the inside and outside surfaces of the large gear tapered split ring, to the inside of the new countershaft gear (large gear) and to the transmission countershaft (the forward most shaft). 3.6 Install new countershaft gear to the transmission countershaft. Insert tapered split ring (tapered end first) into the countershaft gear. Install ring seat tool and spring to counter shaft and new countershaft gear. Torque ring seat tool to 40 ft-lb’s. Figures 3 and 4

Incoming search terms:

HARLEY-DAVIDSON 1984 – 1999 Evo/ 5-Speed & 1999 – 2004 Twin Cam Transmissions Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-04-2012

download
Illustrated Parts List Main Shaft Gear (Small Gear) (1) Special Tools (1 set): • 3/4″ Socket Adapter • Ring-Seat Tool • Spring Tapered Split Ring (2) Counter Shaft Gear (Large Gear) (1) Trap Door Gasket (1) Trap Door (1) .010 Shim /Spacer (20) Delrin Crush Washer (2) Wavy Washer (2) Bearing Lock Nut (2) Nylon Set Screws (4+1 spare) Trap Door Cover Gasket (1) * Not illustrated : Champion Super-lock compound : 0-ring for clutch cable (if needed) : .010″ feeler gauge (3/16″ wide) : Scotch Brite Pad

Incoming search terms:

1999-2002 Kawasaki ZX6R Engine Protection Cage installation instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Follow installation instructions for extended frame sliders. (See page 1) Note: Do not attach delron tips or tighten extended frame sliders until all components are installed. 2. Place the cage loop inside short telescoping tubes on sliders (See fig. G) , push the º”-20 x 1 Ω” bolts through the bolt holes on the telescoping tubes from the outside and start the º”-20 lock nuts to hold cage loop in place. Do not tighten lock nuts at this time. 3. Remove the lower sub frame bolt on the left side of the motorcycle. Install the M10- 1.5 X 88mm stud in place of the sub frame bolt. Place an M10 flat washer and M10-1.5 hex nut on the stud on the interior side of the sub frame. Slide the following components over the stud on the outside of the sub frame in this order: 1.1″ spacer, side strut, (marked with “L”) and M10-1.5 hex nut. (See fig. I) Do not tighten the hex nuts at this time. Repeat for other side using side strut marked with “R”. 4. Push the bottom of the cage loop towards the rear of the motorcycle while pulling the bottom of the left side strut towards the front until the bolt hole on the side strut meets the threaded hole on the tab welded to the cage loop. Attach the side strut to the outside of the tab on the cage loop with a 3/8″-24 x æ” bolt. (See fig J) Do not tighten the bolt at this time. Repeat for other side. 5. Once all components are attached tighten all bolts and nuts. Be sure to torque all engine mount bolts to factory specifications.

Incoming search terms:

TOYOTA SOLARA 1999-2004 VEHICLE WIRING

0

Filed Under (Toyota Manuals) by admin on 23-06-2011

Download
12V CONSTANT WIRE WHITE – WHITE/RED Ignition Harness STARTER WIRE RED Ignition Harness IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/RED Ignition Harness ACCESSORY WIRE BLUE/RED Ignition Harness POWER DOOR LOCK

Incoming search terms: