2000 harley fatboy front end removal

You search Auto repair manual PDF 2000 harley fatboy front end removal, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2000 harley fatboy front end removal Direct Download speed 5282 Kb/s

  2000 harley fatboy front end removal Full Version speed 6162 Kb/s



HARLEY DAVIDSON SCREAMIN' EAGLE STREET PERFORMANCE TOURING END CAP MUFFLER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-04-2011

download
PRODUCT INFORMATION Noise Emission Warranty Harley-Davidson warrants that these mufflers, at the time of sale, meet all applicable United States E.P.A. Federal noise and Emissions standards. This warranty extends to the first person who buys these mufflers for proposes other than resale, and to all subsequent buyers. Warranty claims should be directed to an authorized Harley-Davidson Dealer. Tampering Prohibition Federal law prohibits any modification to this exhaust system which causes the motorcycle to exceed the Federal noise standard. Use of the motorcycle with such a modified exhaust system is also prohibited. NOTE This product should be checked for repair or replacement if the motorcycle noise has increased significantly through use. Otherwise, the owner may become subject to penalties under state and local ordinances. INSTALLATION NOTE Install end caps on mufflers before installing mufflers on vehicle. Install Direct Bolt-On End Caps 1. See Figure 1. Install end cap (2) to muffler (3) with four socket head cap screws (1). Tighten to 82-86 in-lbs (9.3- 9.7 Nm) . 2. Repeat for opposite side muffler. 3 2 1 is05426 1. Socket head screw (4) 2. End cap 3. Muffler Figure 1. Install End Cap on Muffler Install Attachment Ring End Caps 1. See Figure 2. Slide the three U-nuts (2) onto the bosses of the end cap attachment ring cup on the muffler. 2. Install attachment ring (1) to muffler with four socket head cap screws (3). Locate the attachment ring with a U-nut in the 12 o’clock position. Tighten to 82-86 in-lbs (9.3-9.7 Nm) . 3. Slide end cap (5) onto muffler body being careful to align holes in end cap with U-nuts. 4. Install the three countersunk screws (4) and tighten screws securely. 5. Repeat for opposite side muffler

Incoming search terms:

HAR:EY DAVIDSON FLHR/C/S (Road King) FRONT END LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Removal (Left and Right Forks) 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to Touring Model Service Manual and remove front wheel, fender and brakes. 3. Refer to Touring Model Service Manual and remove headlamp nacelle. 4. Loosen fork cap bolt from fork tube plug at top of fork tube, but do not remove. 5. See Figure 1. Standing at front of vehicle, loosen pinch bolt (with lockwasher) on right side of lower fork bracket, but do not remove. 6. Spray glass cleaner on fork tube above the rubber fork stop. After lubricating surfaces, move fork stop up fork tube until it contacts bottom of upper fork bracket. 7. Holding fork slider to prevent fork from dropping, remove fork cap bolt from fork tube plug. Slide fork tube down and out of upper fork bracket, fork stop, lower fork bracket and slider cover. 1 WARNING 1 WARNING 1 WARNING 1 of 5 ® Kit Number 54614-05 Figure 1. Loosen Pinch Bolt on Lower Fork Bracket i04808 1 Fork cap bolt 2 Fork stop 3 Pinch bolt 8. Thread fork cap bolt back into fork tube plug to prevent loss of oil while handling. 9. Move forks to bench area. Place suitable drain pan on floor beneath vise. 10. Repeat Steps 2-6 to remove left fork. Left And Right Fork-Disassembly 1. Remove nuts, lockwashers, flat washers and axle holder from studs at end of fork slider. 2. See Figure 2. Obtain FORK TUBE HOLDER (Part Number HD-41177) and proceed as follows: a. Clamp end of tool in vise in a horizontal position with plastic knobs facing toward you. b. See Figure 3. With the fork cap bolt topside, clamp fork tube between rubber pads on inboard side of tool. Tighten knobs until fork tube is securely held. 3. Remove fork cap bolt from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug from fork tube. Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove 6mm screw from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and discard damper tube. 12. Remove wear ring and rebound spring. Discard rebound spring. Do not expand or stretch retaining clip to remove from fork tube or clip may become bent or distorted. 13. Using pick tool, remove retaining clip between fork slider and fork tube. 14. Remove fork tube from fork slider. NOTE To overcome any resistance, use the fork tube as a slide hammer, that is, first push fork tube into fork slider and then pull it outward with a moderate amount of force. Repeat this sequence until fork tube separates from fork slider. 15. Slide fork oil seal, slider spacer and slider bushing off end of fork tube. Discard fork oil seal and slider bushing. 16. Remove the lower stop. Right and Left Fork-Assembly Exercise caution to avoid scratching or nicking fork tube. Damaging tube can result in fork oil leaks after assembly. 1. See Service Parts Illustration. Obtain new Damper Tube (Item 7, Part Number 46532-04) from kit. Obtain new Rebound Spring (Item 8, Part Number 46273-02) from kit and install on opposite end. Install wear ring removed in step 12. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube. Install lower stop at end of damper tube. 3. Install fork slider in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (14) (Part Number 45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing down fork tube. 5. Slide slider spacer down fork tube until it contacts slider bushing.

Incoming search terms:

HARLEY DAVIDSON FLAME HANDLEBAR GRIPS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
REMOVE AND INSTALL THE LEFT GRIP 1. See Figure 1. Using a T27 TORX® drive head, remove the two screws with flat washers securing the handebar clamp (3) to the clutch lever bracket. Remove the clamp and position the clutch hand lever assembly away from the handlebar 2. Using a T25 TORX® drive head, loosen but do not remove the upper and lower switch housing screws (1). 3. Remove the end cap from the existing left handlebar grip if so equipped. Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. Do not lubricate left handlebar grip before installation. Lubricating grip can cause it to come off while riding, which could result in loss of control and death or serious injury. (00315a) NOTE Make sure that the handlebar surface and the inside of the grip are smooth, dry and thoroughly cleaned of all dirt or adhesive residue. 4. Position the new left grip (4) so the larger flange (5) is at the bottom. Push the grip fully onto the handlebar. 5. Fit the grooves (2) on the outboard side of the upper and lower switch housing over the flanges on the end of the grip, then loosely fasten the two screws. 6. Position the clutch hand lever assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the bottom of the clutch lever bracket. 7. Align the holes in the handlebar clamp with those in the clutch lever bracket, and loosely fasten the two screws with flat washers. Adjust the switch housing and clutch hand control position for rider comfort. 8. Using a T27 TORX® drive head, tighten first the upper, then the lower handlebar clamp screws to 60-80 in-lbs (6.8-9 Nm) . 9. Using a T25 TORX® drive head, tighten first the lower, then the upper switch housing screws to 35-45 in-lbs (4- 5.4 Nm) . 5 3 1 1 4 2 2 is00735 1. Switch housing screws 2. Grooves 3. Handlebar clamp 4. Left handlebar grip 5. Larger flange Figure 1. Left Handlebar Switch Housing REMOVE AND INSTALL THE RIGHT GRIP NOTE Right handlebar switch removal requires a Service Manual for your model and year of motorcycle. A Service Manual can be purchased from your Harley-Davidson Dealer. 1. Refer to the RIGHT HANDLEBAR SWITCH section of the Service Manual for removal of the switch housing assembly. This is necessary to access the throttle cables. 2. Refer to the THROTTLE CONTROL section of the Service Manual to disconnect the throttle cables and remove the existing right grip/throttle sleeve assembly. After removal, make sure that the handlebar end is clean and smooth. 3. Follow instructions in the Service Manual to install the new right grip/throttle sleeve to the handlebar and connect the throttle cables. 4. Verify that the right grip/throttle sleeve rotates and returns freely and does not bind on the handlebar or switch housing.

Incoming search terms:

HARLEY DAVIDSON MULTI-FIT BRAIDED THROTTLE/IDLE CABLE KITS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Disconnect battery cables, negative (-) cable first or remove the main fuse following the instructions in the service manual. NOTE When performing cable disassembly procedures, make careful notes as to the existing cable routing. Pay special attention to existing cable strap locations before removing so new straps can be installed in the same locations. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 2. See Figure 1. Place the cardboard insert between the brake lever and lever bracket. 3 2 1 is00825 1. Brake lever 2.5/32 inch (4 mm) cardboard insert 3. Brake lever bracket Figure 1. Install Cardboard Insert 3. See Figure 2. Loosen cable adjuster jam nuts. Turn cable adjusters in until they are as short as possible. This will provide enough slack for easy removal. 3 4 1 2 5 is 02071 1. Upper switch housing 2. Lower switch housing 3. Throttle cable adjuster 4. Idle cable adjuster 5. Adjuster jam nut Figure 2. Handlebar Throttle Control 4. Remove the right upper and lower switch housing screws. 5. Loosen the upper screw securing the handlebar clamp to the master cylinder housing. Remove the lower clamp screw and flat washer. NOTE If possible, leave the friction shoe in place. The friction shoe is a loose-fit and may fall out or become dislodged if the lower switch housing is turned upside down or shaken. 6. See Figure 3. Remove the brass ferrules from the notches on the inboard side of the throttle control grip. Remove the ferrules from the cable end fittings. 1 2 4 3 is 02072 1. Throttle cable 2. Idle cable 3. Brass ferrule 4. Notch Figure 3. Throttle/Idle Control Cables 7. Pull the crimped inserts at the end of the throttle and idle control cable housings from the lower switch housing. For best results, use a rocking motion while pulling. Remove cables with retaining rings from switch housing. Apply a drop of light oil on the retaining ring, if necessary, to help in removal. NOTE If installing different handlebars, measure the change in distance that will be required from the end of the cable housing to the throttle grip. Compare this additional required length to the cables provided in the kit. If the cables are more than 2.0 inches (51 mm) longer or more than 1.0 inch (25 mm) shorter than the above measured distance, see a Harley-Davidson dealer for the correct cable length. Install proper length throttle cables. Incorrect cable length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00396b) 8. Follow instructions in the applicable service manual and remove air cleaner and backplate.

Incoming search terms:

HARLEY DAVIDSON HYBRID CAM PLATE AND HIGH FLOW OIL PUMP KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. Gasoline can drain from the carburetor fuel line when disconnected from fuel valve fitting. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00256a) NOTES Installing this kit requires removal and installation of the cam support plate. Refer to the service manual for instructions with the following exception pertaining to cam compartment compo- nents: The crank and primary cam sprocket flange bolts are specially hardened, and the flat washers are of a special diameter and have ground surfaces. Use ONLY the parts provided in the Drive Gear Retention Kit (H-D Part Number 25533-99A, sold separately) when installing this kit. -J04804 1 of 7
The cr ank sprocket flange bolts and pr imary cam sproc ket flange bolts ARE NOT interchangeable. 2. Refer to the service manual to remove and discard the crank sprocket flange bolts and primary cam sprocket flange bolts and washers. 3. For 1999 models only: Refer to the service manual to remove and discard the currently installed cam drive sprocket. 4. Refer to the service manual to remove and disassemble the cams from the support plate and oil pump. Discard the support plate and oil pump. 5. For 1999 – 2000 Dyna, 2000 Softail, 1999 – 2000 Touring, and 2001 EFI Touring models only: Inspect the cams, chain, sprockets and chain tensioners for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. For 2001 – 2005 Dyna, 2001 – 2006 Softail, 2002 – 2006 Touring, and 2001 carbureted Touring models only: Inspect the cams and secondary cam chain for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. The primary cam chain, primary sprockets and both tensioners will be replaced by new components from the kit. For ALL models and years: Discard the guide, as it will not be used. INSTALLATION 1. ALL models: See Figure 1. Obtain the new Rear Cam Roller Bearing Kit (H-D Part Number 8983) from inside the Cam Service Kit (H-D Part Number 17045-99C, purchased separately), and install as indicated in Step 2. NOTE See Figure 2. If not enough of the splined shaft is exposed to install the sprocket, omit the spacer (4) and proceed to Step 2e. When the bearing inner race is started onto the machined area, remove the flange bolt (5), flat washer (6) and sprocket, then assemble using the spacer (4). Repeat Step 2e to fully install bearing inner race. To center thrust washer, be sure o-ring is installed in relief groove. Damage to bearing cage and engine can occur if thrust washer is not centered. (00473b) 2. See Figure 1. Install the O-ring (5), thrust washer (4) and bearing inner race (3) onto the rear camshaft as follows: a. See Figure 2. To properly locate the thrust washer (2), install the O-ring (3) in the grinding relief groove on the splined end of the rear camshaft between the machined area and the secondary cam sprocket.

Incoming search terms:

HARLEY DAVIDSON BILLET HEADLAMP WITH SHORT/ TALL MOUNTS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
Kit 68593-06 is a 5-3/4 inch headlamp and kit 69851-06 is a 4-1/2 inch headlamp. Both kits will fit the models listed in Table 1. Table 1. Short and Tall Mount Kits Models Kits 1984-1999 FXSTC, 1998- Later FXST/B, and 2000-Later FXSTD; 1994-2005 FXDWG Short Mount Kit 68595-06 1996-Later XL 1200C and 1998-Later XL 883C; All 2006 Dyna Models; 1999-2000 FXR2/3/4 Tall Mount Kit 69611-06 Additional Parts Required This kit also requires the separate purchase of a Short or Tall Mounting Kit 68595-06 or 69611-06 for your model motorcycle, and can be purchased from a Harley-Davidson dealer. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 21, Table 2 and Figure 22, Table 3. REMOVAL Remove Headlamp and Mounting Bracket for Softail Models To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative (-) battery cable. 2. Remove fuel tank. Refer to FUEL TANK in Service Manual. 3. Disconnect 4-place headlamp connector [38] from main wire harness. Headlamp connector is located under fuel tank on left side. 8 5 7 5 6 2 1 3 4 is01835 1. Screw 2. Washer 3. Nut 4. Lockwasher 5. Washer (2) 6. Screw 7. Mounting block 8. Headlamp assembly Figure 1. Softail and Dyna Headlamp Assembly with Mount (except FXSTD) NOTE All Softails (except FXSTD) complete steps 4 through 6. For FXSTD models complete steps 7 through 9 4. All Softails (except FXSTD): See Figure 1. Remove screw (1) and washer (2) from stem and bracket. Discard screw but save washer for later use. 5. Remove and discard mounting block (7) and headlamp assembly (8). 6. FXSTD models: See Figure 2. Remove screw (1) and washer (2) from stem and bracket. Save screw and washer for later use. 7. Remove and discard nut (3), washers (4), and screw (5). 8. Remove and discard mounting block (6) and headlamp assembly (7). 7 3 4 2 1 4 6 5 is01838 1. Screw 2. Washer 3. Acorn nut 4. Washer (2) 5. Screw 6. Mounting block 7. Headlamp assembly Figure 2. FXSTD Headlamp Assembly with Mount Remove Headlamp and Mounting Bracket for Dyna Models 1. Remove seat following the instructions in the Service Manual. 2. Disconnect negative (-) battery cable. 3. Remove fuel tank. Refer to FUEL TANK in Service Manual. 2 1 is01750 1. Cable strap 2. Wire harness Figure 3. Dyna Service Loop (2005-Earlier) 4. 2005-Earlier FXDWG: See Figures 3 and 4. Remove plug on right side of top frame tube. At service loop, remove cable clip and push wire harness into top frame tube. Pull connector out from hole on right side of tube. 2006-Later FXD: See Figure 5. Remove cover under top frame tube, then pull connector out from opening under tube. 5. Disconnect 4-place headlamp connector [38] from main wire harness

HARLEY DAVIDSON DUAL DISC FRONT BRAKE KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
This kit is designed for installation on the following models which have original equipment 39mm front fork tubes (including chromed tubes) and 19-in. cast-aluminum front wheels: • 2000 – 2003 XLH 883, XLH 883 Hugger and XLH 1200 • 2000 – 2003 FXD (Super Glide) This kit can also be installed on the above XLH and FXD models which have original equipment 39mm front fork tubes and 19-in. laced front wheels only after one of the following procedures is performed: • The original single-flange hub of the 19-in laced front wheel is replaced with a new double-flange hub (H-D Part No. 43629-00), (sold separately) which will accept the second brake disc. OR • The original 19-in. laced front wheel assembly, which has a single-flange hub, is replaced with a new 19-in. laced front wheel assembly (H-D Part No. 43579-00), (sold separately) which has a double-flange hub designed to accept the second brake disc. See the Service Parts Illustration for a list of the contents included in this kit. This kit does not include the front brake line required for a dual disc system; the brake line must be purchased separately as follows: • For XLH 883 motorcycle equipped with low-rise (flat) handlebars, order dual disc brake line H-D Part No. 45148-96. • For XLH 883 Hugger, XLH 1200, and FXD Super Glide models with “buckhorn” (pull-back) handlebars, order dual disc brake line H-D Part No. 45111-96. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) Brakes are a critical safety component. Contact a Harley- Davidson dealer for brake repair or replacement. Improperly serviced brakes can adversely affect brake performance, which could result in death or serious injury. (00054a) Removal and Disassembly – Front Brake System NOTE A Service Manual for your motorcycle is available at your Harley-Davidson Dealer. 1. Block motorcycle underneath frame so that front wheel is raised off the ground slightly. 2. Remove original front brake caliper from left side of front fork according to appropriate Service Manual procedures. Let caliper hang loose on brake line. Save all components and fasteners for reinstallation. NOTE Do not operate the front brake lever with the front caliper removed because the piston may be forced from the caliper. Reseating the piston requires disassembly of the caliper . 3. Remove socket head screw which secures a clamp (retains front brake line) to underside of front fork lower bracket (lower triple clamp). Discard clamp and screw. 4. Remove screw, lockwasher, and clamp which secure front brake line to right rear side of front fork upper bracket (upper triple clamp). Save all components for reinstallation. 5. Remove right mirror and, if applicable, right turn signal lamp assembly from original front brake master cylinder casting. Save all components and fasteners for reinstalla- tion.

Honda GL1000/1100 starter motor Removal/ Over haul Manual

0

Filed Under (Honda) by admin on 08-04-2011

download
1. Remove the three long bolts that hold the sections together and separate them. Be careful as there are a series of flat thrust washers on each end of the armature (located in the middle section). 2. The end cap basically performs no function other than to cover the brush plate and commutator area as well as center the armature shaft in a pressed in bushing located in the end of the cap. 3. The drive end contains the reduction gearing and if need be, can be disassembled to replace the bearing. This is extremely unlikely. The shaft should turn freely and normally only requires a cleaning and grease application. If the bearing in fact needs replacing, simply remove the “C” clips on either end, drive out the bearing and reinstall with an appropriate size replacement. Any decent auto parts / industrial supply should be able to supply the correct bearing. 4. Remove the brush plate from the end of the center section by removing the screw at the one brush connection. Before removing the brushes, note that one of them has an insulating sleeve over the braided wire. The replacement must go in the same brush holder. Remove the brushes and replace if necessary and clean the brush plate. ** Brake Cleaner is a good general cleaner for this entire job. 5. Remove the thrust washers from brush plate end of the armature. Count them and ensure they go back on the correct way. 6. The end of the center section that had the drive end on it has a circular plate covering it with a short splined shaft protruding through the plate. Drive the plate out by tapping the opposite end of the section on the shaft – just lightly with a rubber hammer or piece of wood to protect the shaft. Once the plate is out, remove the armature from the section. You will find more thrust washers at this end. Make sure they go back on correctly. 7. In the center of the center section there are four large Philips screws. These hold in the field coils found within the housing. Using an “impact driver”, loosen the four screws that go around the circumference of the center section and remove them. Remove the 10mm nut for the battery connection and the accompanying fiber insulating washers. With the screws and nut removed, the entire field coil assembly should withdraw entirely from the housing. There will be four (4) metal plates that the screws mounted into come falling out. They are easily replaced into the field coils when you slide it back into the housing. Do not be alarmed that you suddenly have four loose metal parts. 8. With everything out of the housing, thoroughly clean everything using the Brake Cleaner. Although the cleaner will dry without leaving a film, it is suggested that the components be dried with compressed air. 9. Get some extremely fine steel wool (“000″ of even “0000″ is better) and gently clean the metal surfaces or bars of the armature and the commutator. Blow with compressed air. 10. Using a volt/ohmeter, test for continuity between pairs of armature bars (the long ones). There should be continuity between the pairs around the entire circumference.

HARLEY DAVIDSON HEATED HAND GRIP KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
REMOVAL Preparation To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow the instructions given to remove the main fuse. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. Remove the fuel tank according to the service manual instructions. -J04259 1 of 8 Left-Side Grip Removal 1. See Figure 1. Using a T-25 TORX drive head, remove the upper and lower switch housing screws (1). 2. Using a T-27 TORX drive head, loosen the upper screw securing the handlebar clamp (3) to the clutch lever bracket. Remove the lower clamp screw with flat washer. Loosen the clamp and position the clutch hand lever assembly away from the switch housing. Separate the upper and lower switch housings. 3. With “glueless” grip: Remove the grip from the handlebar. With glued grip: Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. 2 2 1 5 4 3 1 is01283 1. Switch housing screws 2. Grooves 3. Handlebar clamp 4. Left handlebar grip 5. Larger diameter of flange Figure 1. Left Handlebar Switch Housing Right-Side Grip Removal Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) NOTE A section of corrugated cardboard or the eyelet of an ordinary cable strap can be used for this purpose. See Figure 2. 1. Place a 5/32-inch (4 mm) thick insert between the brake lever and the lever bracket. 2. Using a T-25 TORX® drive head, remove the upper and lower switch housing screws. 3. Using a T-27 TORX drive head, loosen the upper screw securing the handlebar clamp to the brake master cylinder housing. Remove the lower clamp screw with flat washer. Loosen the clamp and position the master cylinder assembly away from the switch housing. Separate the upper and lower switch housings. 4. Remove the grip from the handlebar. NOTES The twist grip sensor in the right side of the handlebar has a seal cap that protects internal electrodes from dirt and moisture, and also serves as a retention device for the throttle grip. To remove the grip, a slight tug may be necessary to release the index pins in the grip from the receptacle in the seal cap. Upon removing the grip, check the location of the seal cap. If the seal cap is still fastened to the index pins inside the old throttle grip, it can be discarded along with the grip. If the seal cap is still fastened to the end of the twist grip sensor: •See Figure 3. Insert a small screwdriver or other flat-blade tool into the flat area on one side of the seal cap. •Press the leg on the underside of the cap to free it from the slot at the end of the twist grip sensor. Pry up one end of the cap. •Repeat on the other side of the cap. •Carefully remove the cap and discard it

Incoming search terms:

HARLEY DAVIDSON MULTI-FIT BRAIDED THROTTLE/ IDLE CABLE KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect battery cables, negative (-) cable first or remove the main fuse following the instructions in the service manual. NOTE When performing cable disassembly procedures, make careful notes as to the existing cable routing. Pay special attention to existing cable strap locations before removing so new straps can be placed into the same locations. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 2. See Figure 1. Place the cardboard insert between the brake lever and lever bracket. 3. See Figure 2. Loosen cable adjuster jam nuts. Turn cable adjusters in until they are as short as possible. This will provide enough slack for easy removal. 4. Remove the right upper and lower switch housing screws INSTALLATION Throttle and Idle Cable Installation 1. See Figure 3. Apply graphite lightly to the throttle grip inside the switch housing and on the throttle end of the handlebar. NOTE The throttle control cable has a larger diameter retaining ring crimped to the cable end than does the idle control cable. For assembly, apply a drop of light oil on the retaining rings of the crimped inserts. 2. See Figure 7. Push the throttle cable housing and retaining ring into the larger hole of the switch housing, located in front of the tension adjuster screw. 3. Push the idle cable housing and retaining ring into the smaller hole of the switch housing, located behind the tension adjuster screw. 4. Push the throttle and idle control cable housings into the lower switch housing until each snaps into place. NOTE For models not equipped with factory-installed cruise control, if the friction shoe has fallen out or become dislodged, install the shoe with the concave side facing up and position it so the pin hole is over the point of the adjuster screw. 5. Push the throttle control grip over the end of the right handlebar until it bottoms against the closed end. Rotate the grip until the ferrule notches are at the top. To prevent binding, pull the grip back about 0.12 inch (3.2 mm). 6. See Figure 3. Position the lower switch housing beneath the throttle control grip. Install two brass ferrules (Item 3, Figure 11) from this kit onto cables, seating the ferrules in their respective notches on the throttle control grip. The cables must be captured in the grooves molded into the grip. 7. Position the upper switch housing over the handlebar and lower switch housing. Route the wire harness conduit through the depression at the bottom of the handlebar. 8. Tighten the upper and lower switch housing screws finger- tight. 9. Position the brake lever/master cylinder assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the top of the brake lever bracket. 10. Align the holes in the handlebar clamp with those in the master cylinder housing and tighten the lower screw and flat washer finger-tight. Position for rider comfort. Beginning with the top screw, tighten the screws to 60-80 in-lbs (6.8-9.0 Nm)

Incoming search terms: