2000 toyota avalon number 2 cylinder

You search Auto repair manual PDF 2000 toyota avalon number 2 cylinder, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2000 toyota avalon number 2 cylinder Direct Download speed 5282 Kb/s

  2000 toyota avalon number 2 cylinder Full Version speed 6162 Kb/s



HARLEY DAVIDSON XLH 1200cc BIG BORE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
Boring and Honing Procedures 1. Check again for burrs on cylinder gasket surfaces and remove burrs before performing Step 2. 2. Install original head and base gaskets, CYLINDER TORQUE PLATES (Part Number 33446-A) and TORQUE BOLTS (Part Number 33446-4). Tighten TORQUE BOLTS following tightening procedure given in the INSTALLATION, CYLINDER HEAD procedure in the ENGINE section of the Service Manual. NOTE Torque plates, properly tightened and installed with gaskets, simulate engine operating conditions. Measurements will vary as much as 0.001 inch without torque plate. 3. The cylinder must be bored with gaskets and torque plates attached. Bore the cylinder to 0.003 inch under the desired finish size. 1 WARNING CAUTION CAUTION 1 WARNING Kit Number 4. Hone the cylinder to its finished size (See Figure 1) using a 280 grit rigid hone followed by a 240 grit flexible ball hone. Honing must be done with torque plates attached. All honing must be done from the bottom (crankcase) end of the cylinder. Work for a 60 degree crosshatch pattern. 5. See Figure 1. After machining and honing, chamfer the bottom edge of the cylinder liner. the chamfer provides a beveled surface for easier installation of the cylinder over the piston rings. Break leading edge of liner to a flat surface. The bottom edge of the liner will be somewhat sharp after machining. This sharp edge could easily be damaged during installation of the cylinder. Piston Installation The 1200cc pistons have an arrow on the top of the piston. This arrow must face the front of the engine when piston is installed. There is no front cylinder piston or rear cylinder piston. New pistons can be installed in either cylinder. Check piston rings for proper side clearance and end gap (See XLH Service Manual). Be sure end gaps of adjacent rings are installed 90 degrees apart. Assembly Follow assembly and torque specifications given in the ENGINE section of the applicable Service Manual. Replace original gaskets, O-rings and seals with new components furnished in kit. NOTE Push rod covers on 1991 and later models are one-piece and the correct O-rings are as follows: Bottom – Part Number 17944-89 Upper – Part Number 11190 Engine Break In For the first 500 miles, to wear-in critical parts, observe these few simple driving rules: During the first 50 miles, keep the engine speed below 2500 RPM in any gear. Up to 500 miles, vary the engine speed, avoiding any steady speed for long distances. Engine speed up to 3000 RPM is permissible in any gear. Avoid fast starts at wide open throttle. Drive slowly until engine warms up. Avoid running the engine at extremely low RPM in higher gears. 2 of 3 -J00001 1200cc CYLINDER FINAL BORE SIZE AFTER HONING STANDARD BORE DIAMETER 3.4980 inch + 0.0002 inch Figure 1. Bottom Edge of Cylinder Liner Chamfer i04852 Break Edge to Flat Surface

Incoming search terms:

TOYOTA Engine Serial Number Location

0

Filed Under (Toyota Manuals) by admin on 06-10-2011

download
YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2000-2009 4Runner, Avalon, Camry, Corolla, Land Cruiser, RAV4, Sienna, Solar a, Tacoma, Tundra 2007-2009 Camry HV, FJ Cruiser, Yar is 2000-2005 Celica, Echo, MR2 Spyder 2006-2009 Highlander HV 2001-2009 Highlander, Prius, Sequoia 2003-2009 Matrix 2009 Venza The purpose of this TSB is to assist in the identification and location of engine serial numbers on 2000-2009modelyear Toyota vehicles. NOTE When writing a Field Technical and/or Product Report the serial number of the engine MUST be provided.

Incoming search terms:

Short Shift Kit 2000 and up Toyota Celica 2000 and up MR Spyder Installation Manual

0

Filed Under (Toyota Manuals) by admin on 30-05-2011

Download
Step 16: Use the cup remover tool included with the kit to remove both plastic cups on the original shifter. To do so, place the cup remover tool on top of the open jaws of a vice, the jaws should be approximately 1” apart. Hang the shifter from the tool as shown, be sure the shifter is inserted completely into the slot in the tool. Insert a punch into the center hole through the plastic cup and tap firmly with a hammer to separate the original shifter from cup. Repeat for 2nd cup.Re-Installation Install the plastic cups which you removed from the original shifter onto the TWM shifter. Grease the cups and pivot balls. Place the cup on a firm surface and push the TWM shifter into it until it pops in

Incoming search terms:

Toyota Camry L4 – 2.4L 2004 Brakes and Traction Control Disc Brake System Service and Repair

0

Filed Under (Toyota Manuals) by admin on 24-05-2011

Download
REMOVE FRONT DISC BRAKE CYLINDER SLIDE BUSH 10. Remove the cylinder slide bush from the cylinder slide pin.
a. REMOVE FRONT DISC BRAKE BUSH DUST BOOT 11. Remove the 2 bush dust boots from the disc brake cylinder mounting. a. REMOVE FRONT DISC BRAKE CYLINDER MOUNTING LH 12. Remove the 2 bolts and disc brake cylinder mounting LH. a. REMOVE CYLINDER BOOT 13. Using a screwdriver, remove the set ring and cylinder boot.
a. REMOVE FRONT DISC BRAKE PISTON 14. Place a piece of cloth or similar, between the piston and the disc brake cylinder. a. Use compressed air to remove the piston from the disc brake cylinder. CAUTION: Do not place
your fingers in front of the piston when using compressed air. NOTICE: Do not spatter the brake fluid

Incoming search terms:

HARLEY DAVIDSON ADVANCED AUDIO HANDS FREE PHONE INTERFACE KIT INSTALLATION

0

Filed Under (Harley Davidson) by admin on 12-04-2011

download
The Hands Free interface module in this kit requires proximity to a BluetoothTM-enabled cellular phone in order to function. The phone must be a model that is compatible with the interface module (go to to view the compatibility chart), and must be paired to the interface module according to the instructions included with the cell phone. NOTE The cell phone MUST be available to the installer in the final steps of the installation (prior to re-installation of the outer fairing) in order to program and test the hands free functions. To avoid unnecessary delays, please take this into consideration when scheduling the installation. FLHT models will require prior installation of an Advanced Audio AM/ FM/ CD Radio Kit (Part Number 76412-06) and a Tour-Pak Mount AM/ FM Antenna Kit (Part Number 76317-06). FLHT, FLHX and FLTR models will require the prior installation of a Tour Pak®. See a Harley-Davidson dealer for avail- ability of color-matched King or Chopped Tour-Paks to match your vehicle, and additional items that may be required when mounting the Tour-Pak to your model. Unless one has already been fitted as part of another Advanced Audio kit installation: FLHTCU models will require the additional purchase of an Ultra Overlay Harness (Part Number 70164-06). FLHT, FLHTC and FLHX models will require the separate purchase of a Communication Switch Kit (Part Number 77173- 06). FLHX models will require the separate purchase of: •a fuel tank console (Part Number 61270-98A), •a console extension (Part Number 52447-96), •a rubber molding (71294-89), •a 1/4-20 clip nut (Part Number 7964), •a button-head screw (Part Number 3652), •a plastic wire clip (Part Number 10120), and •an adhesive-backed metal wire clip (Part Number 10103). FLTR models will require the separate purchase of: •a Console Pod Assembly (Part Number 77136-03), and •three pan-head screws (Part Number 2462). NOTE See a Harley-Davidson dealer for availability of optional decorative inserts for the Console Pod Assembly. ALL models will require the additional purchase of: •a Non-Ultra Overlay Harness (Part Number 70169-06), and EITHER : •a Premium Stereo Helmet Headset (Part Number 77147- 98) OR a Hand-Held CB Microphone Kit (Part Number 76312-98

Incoming search terms:

TRIUMPH 750 BIG BORE CYLINDER AND PISTON SET FOR 650 TWINS INSTALLATION

0

Filed Under (Triumph) by admin on 29-10-2010

download
Step 1. Unpack your big bore kit and inspect the contents. There should be the following: 1. Cylinder x l 2. piston with wristpin x 2 3. Hepolite piston ring set x l 4. Special big bore head gasket Step 2. Thoroughly wash the cylinder bores with soap and water. Do not use solvent! Dry bores with air or a lint free towel and let completely air dry. This step is most important and will greatly extend the life of the pistons. Step 3. Following the procedure outlined in your service manual, drain the fuel tank, remove the exhaust system, fuel tank and carburetors. Have a catch basin handy to capture any fuel that may spill from the carburetors, as fuel is highly flammable and can be ignited by a dryer pilot light etc. from a long distance. Clean up any spilled fuel immediately and dispose of away from any source of ignition. Store the fuel tank in a well vented area, outdoors is best, in the event your fuel taps should leak. Step 4. Remove the rocker boxes by slacking the 9 head bolts a little at a time in a star pattern. Remove the 6 nuts at the front and back of the head. Remove the 4 corner rocker box bolts. Remove the head bolts and rocker boxes. Remove the push rods. Examine the push rods to insure they are straight and the ends are tight. Replace any suspect push rod. Step 5. Remove the cylinder head. Now would be a good time for guide and valve renewal. This is best left to an expert. More cylinder heads have been ruined by auto machine shops than by hard use. If you do not have a qualified shop in your area please call for a referral. Step 6. Remove the push rod tubes and the cylinder base nuts. Clip rubber bands around the top of the lifters to keep them from dropping into the crankcase. Have a few lint free rags handy. Bring the pistons to the top of the stroke and begin lifting off the cylinder. If the cylinder is hard to lift off, thread a nut on one of the base studs and use a tire lever to pry against the bottom fin close to its base using the stud as a fulcrum. After partially raising the cylinder stuff the crankcase mouth with rags to keep any carbon or broken rings from entering the crankcase. These will remain in place until step 12. Step 7. Leaving the rags in the crankcase remove the wrist pin circlips from the pistons and discard. Heat the piston and gently push the wrist pin out. Do not use force as this can damage the connecting rod or its bearings. Be sure to account for all the clips as one left in the crankcase can do extensive damage. Step 8. Clean all gasket surfaces to remove any traces of the old gaskets. Use Pennatex gasket remover if needed. Be very careful not to scratch the gasket surface or to allow any gasket particles to enter the crankcase. Even a small bit of gasket can stop the oil pump from working! Step 9. Note the direction and location of the lifters. These must be replaced in the same position as when removed. Remove the lifter blocks from the old cylinder. Start by removing the small retaining bolts and washers. The lifter blocks are extremely fragile and are easily broken. They are also very expensive so great care must be taken in this step! Triumph special tool 222-616008 is advisable here. Apply pressure to the center of the block only. Do not press against the tangs that locate the lifter! A tool can be fabricated using two dowels to locate in the lifter holes. Step 10. Clean and examine the lifters and camshaft faces. Clean the lifter blocks and remove the sealing oring under the locating flange. Replace these with the new orings in the gasket set. Apply a smear of gasket sealant to the lifter block oring and press into the new cylinder. Be sure the lifter block is parallel with the bores and the grooved block is on the exhaust side. Apply a small amount of assembly oil to the lifters and replace in the exact position they came from

Incoming search terms:

HARLEY DAVIDSON CHROME MASTER CYLINDER AND CLUTCH BRACKET KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
MASTER CYLINDER REMOVAL See Figure 1. Master cylinders designed for dual disc (two caliper) operation have an 11/16 inch (17.5 mm) bore, while those that are designed for single disc (one caliper) operation have a 9/16 inch (14.3 mm) bore. The bore size is stamped (1) on the master cylinder assembly inboard of the handlebar clamp bracket. NOTE Do not use an 9/16 inch bore master cylinder assembly on dual disc (two caliper) models or dual disc 11/16 inch bore master cylinder assembly on single disc (one caliper) models. These master cylinder assemblies are not interchangeable. Using the wrong assembly can adversely affect braking efficiency or result in brake failure which could result in death or serious injury. D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) 1 is 01230 1. Bore stamp size location Figure 1. Verify Correct Master Cylinder Bore Size 1. Open bleeder nipple caps on front brake caliper. Install end of a length of clear plastic tubing over caliper bleeder valves, while placing free end in a suitable container. Open bleeder valves about 1/2-turn. Pump brake hand lever to drain brake fluid. Close bleeder valve. Avoid leakage. Be sure gaskets, banjo bolt(s), brake line and master cylinder bore are clean and undamaged before assembly. (00322a) 2. Remove bolt and two steel/rubber washers to disconnect fitting of hydraulic brake line from master cylinder. Discard washers. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 3. See Figure 2. Place the cardboard insert between the brake lever and lever bracket

Incoming search terms:

Toyota Camry, 1992-1996 Avalon Repair & Service Manual

0

Filed Under (Toyota Manuals) by admin on 25-05-2011

epair manual covers all Toyota Camry 1992-1996, and Toyota Avalon models, 1995-1996.

Table of Contents

* Introduction: Vehicle identification numbers. Buying parts. Safety. Maintenance techniques. Chemical and lubricants, and more.
* Tune-up and routine maintenance
* Four-cylinder engine
* V6 engines
* General engine overhaul procedures
* Cooling, heating and air-conditioning systems
* Fuel and exhaust systems
* Engine electrical systems
* Emissions control systems
* Transmission

Incoming search terms:

1999 Toyota Camry LE V6 Body and Interior Maintenance Record

0

Filed Under (Toyota Manuals) by admin on 03-10-2011

download
Action Date Mileage Day Cost (with tax) By Interval Notes Oil and Oil Filter Change 8/30/1999 2494 Monday$77.97 Dealer 2494Non-synthetic 5w-30 (Toyota dealer stock) Oil and Oil Filter Change 10/31/1999 5484 Sunday $30 Owner 2988.5Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 12/30/1999 8460 Thursday$30 Owner 2975.9Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 2/21/2000 11414 Monday $30 Owner 2953.3Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 4/22/2000 14479 Saturday$30 Owner 3065.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 7/4/2000 17339 Tuesday$30 Owner 2860.1Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Air Filter – Replace 7/4/2000 17339 Tuesday$15 Owner 17339Purolator A24690 Air Filter Oil and Oil Filter Change 9/16/2000 20161 Saturday$30 Owner 2821.9Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Transmission Drain and Fill 10/27/2000 21913 Saturday$15 Owner 21913Drain and Fill 2.5 Quarts Mobil 1 Dexron III Synthetic ATF Transmission Drain and Fill 10/28/2000 21920 Sunday $15 Owner 7Drain and Fill 2.5 Quarts Mobil 1 Dexron III Synthetic ATF Oil and Oil Filter Change 11/19/2000 23066 Sunday $30 Owner 2904.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 2/11/2001 26062 Sunday $30 Owner 2996.1Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Transmission Flush 4/30/2001 28351 Monday$135 Dealer 2835113 Quarts Mobil 1 Dexron III Synthetic ATF – TransTech Flush Tires – Rotate 5/12/2001 28766 Saturday$0 Dealer 28766Tires – Rotate Coolant Flush 5/12/2001 28766 Saturday$112 Dealer 28766Toyota Red Coolant + MOC Flush (Extended warranty with service) Oil and Oil Filter Change 5/13/2001 28793 Sunday $30 Owner 2730.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Air Filter – Replace 5/13/2001 28793 Sunday $15 Owner 11454Purolator A24690 Air Filter PCV Valve – Replace 5/26/2001 31083 Saturday$10 Owner 31083Toyota OEM PCV Valve Windshield Wipers – Replace 5/26/2001 31083 Saturday$10 Owner 31083Windshield Wipers – Replace Oil and Oil Filter Change 5/27/2001 31296 Monday $30 Owner 2502.8Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 9/15/2001 34374 Saturday$30 Owner 3078.5Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Tires – Replace 9/28/2001 34784 Friday$431.23 Dealer 34784 (4) Bridgestone RE950 Tires (2 of original tires had tread separation – ~30% tread remaining) Oil and Oil Filter Change 11/12/2001 37365 Monday $30 Owner

Incoming search terms:

HARLEY DAVIDSON CHROME FRONT BRAKE MASTER CYLINDER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
1. See Figure 2. Drain the brake fluid. a. Open bleeder nipple cap on front brake caliper. b. Install end of a length of clear plastic tubing over caliper bleeder valve, while placing free end in a suitable container. c. Open bleeder valve about 1/2-turn. d. Pump brake hand lever to drain brake fluid. e. Remove cover. f. Close bleeder valve. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) 2. Remove bolt and 2 steel/rubber washers to disconnect fitting of hydraulic brake line from master cylinder. Discard washers. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) is 01010 Figure 3. 5/32 in. (4 mm) Cardboard Insert 3. See Figure 3. Place the cardboard insert between the brake lever and lever bracket. 4. Using T27 TORX® drive head, remove the 2 screws with flat washers securing the handlebar clamp to the master cylinder housing. Remove the brake lever/master cylinder assembly and clamp from the handlebar. Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) 5. Remove retaining ring from pivot pin groove at bottom of master cylinder bracket. 6. Remove pivot pin and brake hand lever from master cylinder assembly. NOTE New master cylinder comes with all internal components preassembled. It is not necessary to remove the components from the bore of the old master cylinder. See Figure 9. Use denatured alcohol to clean clutch system components. Do not use mineral-based solvents (such as gasoline or paint thinner), which will deteriorate rubber parts even after assembly. Deterioration of these components can cause clutch failure, which could result in death or serious injury. (00296a) 7. With denatured alcohol, clean and inspect all parts that will be reused. Replace as necessary and wipe dry with a clean lint free cloth

Incoming search terms:

Incoming search terms: