2000 v starr 1100 custom carburetor removal

You search Auto repair manual PDF 2000 v starr 1100 custom carburetor removal, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2000 v starr 1100 custom carburetor removal Direct Download speed 5282 Kb/s

  2000 v starr 1100 custom carburetor removal Full Version speed 6162 Kb/s



YAMAHA V-Star 1100 Carburetor Bowl Screw Repair and Removal After Stripping and Pilot Cap Removal

0

Filed Under (Yamaha) by admin on 19-01-2012

download
When I first started working on bike many years ago, I learned the danger of stripping the heads of Philips screws when removing or installing them on motorcycles. I remember the two worst screws were the casing side-cover aluminum screws and carburetor bowl screws. I think I tried every method of screw removal after they were stripped. Vice grips, better tipped screwdriver, hammer, drill, and other tools were used. One way I learned to remove stripped screws is to re-make the Philips head into a flathead screw. Cutting a slot in the top of the screw and then use a flat-head screwdriver to remove the screw. On some parts this technique can work, other parts and screws it may not. The Philips screws on the bottom of the V-Star carburetor bowls are VERY prone to stripping. In fact, I will not start a carburetor cleaning without new hex head screws to replace the original Philips bowl screws. Replace the bowl screws for yourself if you keep the bike, or for the next rider that will appreciate the hex-head screws when they clean the carburetors. Not many other parts on a V-Star have screws that are prone to stripping. This documentation is to help riders with motorcycle maintenance. Some riders will find themselves with the problem of removing stripped screws. A carburetor cleaning can quickly double in time when you realize the hardest part of the job is removing bowl screws after they strip. And then realizing you do not have the replacement hex-head screws available and must now go to the hardware store.

Incoming search terms:

2001-2003 XV16 Fuel Pump and Carburetor Removal

0

Filed Under (Yamaha) by admin on 31-12-2011

download
Disconnect the carburetor fuel line hose at the fuel pump. •Disconnect the fuel pump wire coupler. •Remove the choke cable from fuel pump bracket. •Remove the upper engine mount, leaving the fuel pump attached to the mount. •Disconnect the TPS and carburetor wire couplers.       Disconnect the throttle cables, and then remove the carburetor. NOTE: The idle adjuster can be removed from its bracket without loosening the bracket screws. PAGE 3 of 12 HIDDEN 6mm SCREW 6mm BOLT UPPER ENGINE MOUNT/ FUEL PUMP CARBURETOR PAGE 4 of 12 Right-Hand Footrest Removal: •Disconnect and remove the brake light switch. •Remove the forward-most tie wrap around the brake hose and frame. •Remove the footrest assembly. NOTE: Leave the brake hose attached. Move the hose to the underside of the foot rest mount and support it as necessary so that it is out of the way Cylinder Head Oil Pipe Removal/ Installation: •Slightly loosen all three banjo bolts before removing them to prevent oil line deformation. NOTE: When loosening the upper banjo bolts, hold the line in place using a wrench at the flat surface on the fitting. Air Injection System (AIS) Removal: •Remove the electric starter motor. •Remove the regulator/rectifier assembly. Remove the AIS pipes from the cylinder head, but leave them attached to the AIS assembly. •Remove the three screws with 8mm heads, and then remove the AIS air filter from the right side. •Remove the three Phillips head screws holding    the AIS assembly on the frame. •Remove the AIS assembly from the left side. FOOTREST ASSEMBLY UPPER BANJO BOLT AIS AIR FILTER AIS ASSEMBLY
PAGE 5 of 12 Transfer Case Removal: •Remove the transfer case bracket first. Then remove the outer chrome cover, inner cover, and drive-sprocket nut. NOTE: There is a sealing washer between the inner case and the transfer case at the 8mm stud. Be sure to replace it during re-assembly. •Remove the two chrome oil lines between the engine and oil tank. NOTE: Retain the four O-rings for re-use. •Remove the drive pulley cover and remove the drive pulley nut. •Loosen the drive belt tension. •Remove the drive pulley, inner cover, collar, and O-ring. NOTE: The collar has a bevel on its inside diameter     for the O-ring facing inward and a bevel on the outside diameter facing the pulley. •Remove the drive and driven sprockets with chain as an assembly. •Remove the collar and O-ring. NOTE: Collar has a bevel on its inside diameter that faces inward for the O-ring. •Remove oil tank filler neck. •Remove the relay bracket on the right-hand side. NOTE: Leave the relays connected. Simply move them out of the way to allow room for transfer case removal. •Slide the transfer case out from the right side.

Incoming search terms:

Yamaha V-Star 1100 Needle/ Jet Kit REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Honda) by admin on 27-12-2011

download
To install this needle and jet kit: • Remove carburetors from the engine per Yamaha shop manual procedures. Note: Always perform internal carburetor work in a clean area. • Remove the vacuum slide from each carburetor. • Remove the OEM needle, spacer and washers, noting order of assembly. (Note; the washers are used as shims to raise the needle, each is equivalent to ½ clip position, use these to fine tune the needle) • Counting from the top to the bottom, install the new Baron needle clip on groove #4 of the replacement Baron adjustable needles. The top is the blunt end of the needle. • Reinstall the OEM spacer and washers as shown in the figure below. • Reinstall the vacuum slides along with the diaphragm spring and reattach the diaphragm covers Note: Verify that the slides maintain their full range of movement! • Drain the fuel from the float bowls and remove the bowl covers. • Remove the OEM main jets and replace them with Baron’s supplied Mikuni main jets. Install the “base setting” main jets as indicated above. NOTE: V-Star 1100 carburetion runs staggered jetting! Make sure the front cylinder’s carburetor gets the larger main jet (numerically), and the rear cylinder’s carburetor gets the smaller main jet . Important! Extra jets have been included in your kit. These will help you fine-tune the carburetors for changing conditions. These conditions include climate and weather patterns in your area as well as exhaust equipment on your motorcycle. Barons determines the jet and clip recommendations that best suit your average riding conditions based upon information supplied to us at the time of your order. Changes in weather, altitude or modifications to your exhaust system may require jets other than those supplied. • Thoroughly clean the inside of the float bowls prior to reinstalling them. 311 #1 Industrial Way – Fallbrook, CA 92028 – USA Phone: (760) 731-1200 Fax: (760) 731-1284 E-mail: tech@baronscustom.com Website: www.baronscustom.com Included in this kit: (4)Mikuni main jets #107.5, 110, 112.5, 115, (2) titanium needles, (2) clips, (8) cap-head allen screws Tools required: 3-4-5 mm allen wrenches, 10&12 mm sockets, 10mm end wrench, phillips & flat screwdrivers, pliers, drill. Revision 4.0 • Reassemble the carburetors by reversing the order of above steps. Use the new supplied cap head Allen screws in place of the OEM Phillips head screws for the float bowls. • Locate the fuel mixture screws – they will either be a screw head or a brass plug. If it is a screw head, skip to step c . If you see a brass plug with a small hole in the center, proceed as follows: a. With a 5/32″ drill bit, carefully and slowly drill through the fuel mixture plugs

Incoming search terms:

HSR Carburetor Total Kits Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
Intake Manifold: 1. Install MAP sensor in Mikuni manifold (Twin Cam only). 2. Attach the Mikuni manifold to the engine. Align the manifold before tightening the bolts. The flange surface of the Mikuni manifold should be parallel with the front of the engine’s cam cover. Use a level or angle meter to check this. Tighten the manifold bolts. 3. Attach the rubber flange to the Mikuni manifold with the furnished 5/16″x3/4″ bolts and washers. Choke Cables: Mikuni & Harley-Davidson Route the cable with largest radius bends possible. Check the cable for free-play after installation. If there is no free-play, the engine may run rich and deliver poor performance or low fuel mileage. Harley Cable (Twin Cam Kits: 42-19, 45-4) : 1. Remove the Harley choke cable from the stock carb. 2. Remove the spring and plunger from the cable. 3. Remove the spring and plunger from the Mikuni. 5. Install the Mikuni spring and plunger onto the Harley choke cable. Change nothing else; be sure to use the Harley plastic nut, not the Mikuni nut (See Figure 1). Total Kit Installation Instructions The HSR series carburetors are precise yet durable instruments; however, like any other piece of fine equipment, they require correct installation and reasonable care to assure optimum performance and long life. Extra time spent during installation will pay off in both short and long term performance and reliability. This Mikuni HSR carburetor kit is designed to be a bolt-on application, and as such, is set-up and jetted properly for most applications. However, since Harley-Davidson motors are often highly modified, alternate tuning settings may be required. The Mikuni Tuning Manual helps make jetting alterations and adjustments an easy matter. NOTE: Carburetor Kits not designated as C.A.R.B. exempt, are not legal for motor vehicles operated on public highways in the state of California, or in any other states and countries where similar laws apply. WARNING NOTE: NOTE: WARNING CAUTION NOTE: NOTE: TK-2 6. Install the new assembly into the Mikuni carburetor. Be careful to only gently tighten the plastic nut. 7. Loosen the knurled plastic friction nut behind the choke knob and check for free-play (see Figure 2). Figure 1: Harley nut with Mikuni spring & plunger Figure 2: Choke cable adjustments Mikuni Cable (Evo Kits: 42-8, 45-2 & 45-3) : 1. Remove nut, spring and plunger from the Mikuni. 2. Install the nut, spring and plunger onto the cable. 3. Install the assembly into the Mikuni HSR carburetor. Be careful to only gently tighten the plastic nut. 4. Check for free-play. Adjust the cable as necessary. An optional choke cable mounting bracket is included in the Evo kits for custom installations. Carburetor Installation: 1. Insert the carb fully into the rubber flange, align with engine and tighten the clamp. 2. Slip the fuel hose onto the carburetor’s fuel fitting and secure with the enclosed hose clamp. NOTE: Some Twin Cam installations may require removal of a small amount of fin material from the cylinders to clear the float bowl. Throttle Cables The HSR carburetor uses stock 1990 and later Harley- Davidson cables. However, if your Harley is fitted with some other carburetor, you may need to purchase a set of cables. See your dealer for the correct cable set. 1. Route the throttle cables with large radius curves and so they do not interfere with other components. 2. Screw the cable adjusters together to make them as short as possible. 3. Connect the “close” cable first (see Figure 3). 4. Install the “open” cable next (see Figure 3). 5. Adjust the opening cable until the slide can be opened fully. Snug the adjuster lock nut. 6. Turn the handlebar to the right and adjust the throttle free-play with the closing cable adjuster to approximately 1/8″ (see Figure 4)

Incoming search terms:

KTM 60 SX / 65 SX REPAIR MANUAL ENGINE

0

Filed Under (KTM) by admin on 12-11-2010

download
Carburetor adjustment Basic information about the original carburetor setting The original carburetor setting was adapted for an altitude of approx. 500 meters (1600 ft.) above sea level, and the ambient temperature of approx. 20°C (68°F), mainly for off-road use and central European premium-grade fuel (ROZ 95). Mixing ratio 2-stroke motor oil : super fuel 1:40 . Basic information of changing the carburetor setting Always start out from the original carburetor setting. Essential requirements are a clean air filter system, air-tight exhaust system and an intact carburetor. Experience has shown that adjusting the main jet, the idling jet and the jet needle is sufficient and that changes of other parts of the carburetor will not greatly affect engine performance. RULE OF THUMB: high altitude or high temperatures  choose leaner carburetor adjustment low altitude or low temperatures  choose richer carburetor adjustment * WARNING * -ONLYUSE PREMIUM – GRADE GASOLINE ROZ 95 MIXED WITH HIGH – GRADE TWO – STROKE ENGINE OIL . OTHER TYPES OF GASOLINE CAN CAUSE ENGINE FAILURE , AND USE OF SAME WILL VOID YOUR WARRANTY . -ONLYUSE HIGH – GRADE 2- STROKE ENGINE OIL OF KNOWN BRANDS ( I . E .SHELL ADVANCE RACING X). -NOTENOUGH OIL OR LOW – GRADE OILCAN CAUSE EROSION OF THE PISTON . USING TOO MUCH OIL , THE ENGINE CAN START SMOKING AND FOUL THE SPARKPLUG . -INTHE CASE OFA LEANER ADJUSTMENT OF THE CARBURETOR PROCEED CAUTIOUSLY . ALWAYSREDUCETHEJETSIZEINSTEPSOFONENUMBERTOAVOID OVERHEATING AND PISTON SEIZURE . NOTE: If despite a changed adjustment the engine does not run properly, look for mechanical faults and check the ignition system. Basic information on carburetor wear As a result of engine vibrations, throttle valve, jet needle, and needle jet are subjected to increased wear. This wear may cause carburetor malfunction (e.g., overly rich mixture). Therefore, these parts should be replaced after 1000 hours of using. Idling range – A Operation with closed throttle valve. This range is influenced by the idle adjusting screw 1 . Only make adjustments when the engine is hot. The idling speed can be changed by turning the idle adjusting screw. Turning it clockwise produces a higher idling speed and turning the screw counterclockwise produces a lower idling speed. Opening up – B Engine behavior when the throttle opens. The idle jet and the shape of the throttle valve influences this range. If, despite good idling-speed and part-throttle setting, the engine sputters and smokes when the throttle is fully opened and develops its full power not smoothly but suddenly at high engine speeds, the mixture to the carburetor will be too rich, the fuel level too high or the float needle is leaking. Part-throttle range – C Operation with partly open throttle valve. This range is only influenced by the jet needle (shape and position). The optimum part-throttle setting is controlled by the idling setting in the lower range and by the main jet in the upper range. If the engine runs on a four-stroke cycle or with reduced power when it is accelerated with the throttle partly open, the jet needle must be lowered by one notch. If then the engine pings, especially when accelerating under full power at maximum engine revs, the jet needle should be raised. If these faults should occur at the lower end of the part throttle range at a four-stroke running, make the idling range leaner; if the engine pings, adjust the idling range richer

Incoming search terms:

CUSTOM LED 2004-2006 YAMAHA ROAD STAR INTEGRATED TAIL KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 10-11-2010

download
1 ) REMOVE THE SCREWS ON THE BACK SIDE OF THE TAIL LIGHT THAT HOLD THE CHROME TRIM TO THE TAIL LIGHT. 2 ) POSITION YOUR CUTTING WHEEL AS SHOWN IN THE PICTURE TO THE LEFT WHERE THE CLEAR PART OF THE LENS TURNS 90 DEGREES. THE CUTTING WHEEL SHALL REMAIN IN THE PLANE OF THE LENS. 3 ) PROCEED TO CUT INTO THE CLEAR LENS APPROXIMATELY HALF OF THE THICKNESS, ALL THE WAY AROUND THE PERIMETER OF THE LENS – BE SURE NOT TO CUT ALL THE WAY THROUGH BECAUSE IT WILL NOT GLUE BACK TOGETHER PROPERLY. SEE “TIPS FOR CUTTING YOUR LENS” BEFORE BEGINNING. TIPS FOR CUTTING YOUR LENS A) KEEP THE CUTTING WHEEL MOVING AND APPLY LIGHT PRESSURE. SITTING IN ONE SPOT WILL JUST MELT THE PLASTIC. WHEN YOU MAKE YOUR WAY AROUND THE ENTIRE PERIMETER, CLEAN ALL THE BURRED PLASTIC FROM AROUND THE EDGES AND FROM INSIDE THE GROOVE YOU’VE MADE. OPENING THE LENS 4 ) PLACE THE TIP OF A FLAT HEAD SCREWDRIVER IN THE GROOVE YOU HAVE CREATED. 5 ) GENTLY TWIST THE SCREWDRIVER TO CRACK THE GLUE ALONG THE GROOVE. NOTE: AS SOON AS YOU HEAR THE SOUND OF THE GLUE GIVING (A CRACK), MOVE THE SCREWDRIVER SLIGHTLY AND ADVANCE THE CRACK. SLOW AND STEADY IS THE NAME OF THE GAME HERE. IF YOU FIND A HARD SPOT, WEAKEN IT WITH THE CUTTING WHEEL AS NECESSARY. THE HARD PART IS OVER! YOU CAN RELAX NOW! 2 ©2005 Custom LED LLC. All Rights Reserved. 6 ) REMOVE THE SCREWS HOLDING THE STOCK LED BOARDS TO THE HOUSING (YOU WILL BE REUSING SOME OF THE SCREWS SO PUT THEM TO THE SIDE). 7 ) REMOVE THE STOCK LED ASSEMBLY FROM THE LENS HOUSING. YOU WILL NO LONGER NEED THE STOCK LED BOARD, DISPOSE OF IT AS YOU WISH. 8 ) GENTLY PRY OFF THE PLASTIC COVER TO EXPOSE THE DRIVER BOARD UNDERNEATH. 9 ) REMOVE THE SCREWS SUPPORTING THE DRIVER BOARD AND SNIP OFF THE THREE WIRES (BLUE, BLACK, YELLOW) AS SHOWN AS CLOSE TO THE CIRCUIT BOARD AS POSSIBLE! YOU WILL NEED TO CONNECT TO THESE WIRES LATER. 10 ) POP OUT THE LITTLE BLACK PLUG AS SHOWN IN THE PICTURE. YOU CAN POKE IT OUT FROM THE INSIDE OF THE HOUSING. WIRING UP YOUR CUSTOM LED BOARD PLACE YOUR CUSTOM LED INTEGRATED TAIL BOARD NEXT TO THE HOUSING AND MATCH THE WIRE COLORS AS FOLLOWS: TRY TO HANDLE THE CIRCUIT BOARD AS LITTLE AS POSSIBLE AS FINGERPRINTS AND DIRT WILL HINDER THE PERFORMANCE. • BLACK ON HARNESS TO 6″ BLACK ON CUSTOM LED BOARD • BLUE ON HARNESS TO 6″ BLUE ON CUSTOM LED BOARD • YELLOW ON HARNESS TO 6″ YELLOW ON CUSTOM LED BOARD USE THE THREE (3 OF 5) SUPPLIED ORANGE SPLICE CONNECTORS. PUSH THE TWO WIRES TO BE SPLICED TOGETHER INTO THE OPEN END. BE SURE TO PUSH THE WIRES ALL THE WAY IN (UNTIL YOU CAN SEE THEY HAVE REACHED THE OTHER SIDE). NOTE: YOU WILL NEED TO SEPARATE THE THREE WIRES FIRST BY CUTTING THE PLASTIC COLLAR THAT BINDS THEM. FOR THE WIRES TO FIT PROPERLY INTO THE CONNECTORS, YOU MUST ALSO REMOVE THE REMNANTS OF THE COLLAR FROM THE WIRES. NOTE: THE SPLICE IS MORE RELIABLE IF THE WIRE IS NOT STRIPPED. BE SURE TO SNIP OFF THE BARE ENDS OF THE WIRES ON THE CUSTOM LED TAIL TO ENSURE THAT THERE IS INSULATION WHERE THE SPLICE WILL OCCUR. THE SUPPLIED SPLICE CONNECTORS AUTOMATICALLY DISPLACE THE INSULATION AS NECESSARY. ONCE YOU DOUBLE CHECK YOUR COLOR MATCHING AND ARE ABSOLUTELY SURE THAT THE WIRES ARE FULLY INSERTED INTO THE SPLICE CONNECTORS DO THE FOLLOWING: 11 ) SQUEEZE THE SPLICE CONNECTORS FIRMLY WITH PLIERS. VISUALLY INSPECT YOUR CONNECTIONS TO SEE THAT THEY HAVE BEEN SPLICED PROPERLY INSIDE. 12 ) RUN THE GREEN AND BROWN WIRES THROUGH THE HOLE YOU OPENED UP IN STEP 9

Incoming search terms:

ODYSSEY DRYCELL MOTORCYCLE BATTERY COMPATIBILITY

0

Filed Under (Triumph) by admin on 30-10-2010

download
BMW 1200 1200 1150 1100 1100 1000 1000 1000 1000 900 850 800 800 800 750 750 750 750 750 650 650 600 600 500 BUELL 1200 1200 1200 1000 DUCATI 860 750 500 HARLEY DAVIDSON 1570 1570 1450 1450 1340 1340 1340 1200 883 HONDA 1800 1500 1200 1100 1000 1000 900 750 750 650 650 650 600 400 200 150 150 125 K1200RS, LT R1200C R1150GS, R R1100GS/R R1100RS/T/S/LT “K” Models R100/7 100RS R100GS, R, RS, RT R90/6, R90S R850R R80GS, R80ST R80, R80RT R80/7/RT K75, RT K75C, S R75/5 R75/7 R75/6 R65 R65LS R60/5 R60/6, R60/7 R50/5 S1 Lightning X1, S3, S3T, M2 S2/T, RS1200, RR1200 RR1000 GT, GTS GT, Laguna Seca GTL, GTV, Sport FXST, FLST FXD FXD FXST, FLST FXD FXST, FLST FL/H/T/HT XL, XLH XLH, XLH GL1800, VTX1800C Gold Wing-All Gold Wing-All Gold Wing-GL1100 CBX1000, SS opt. Gold Wing-GL1000 CBR900R,RR CB750A (Hondamatic) VFR740R/ RVF750R NT650, SLR650, NX650 Vigor 650 XR650L VT600C, CD, CBR600 CBR400F CB-1 TR200 Fat Cat CH150 Elite FES150 FES125, Pantheon (97 -) (98 -) (00 -) (94-00) (90 -) (83-93) (76-84) (83) (87-95) (69-76) (95-97) (80-96) (84-95) (78-84) (85-95) (85-95) (70-73) (76-84) (69-76) (84-95) (78-84) (70-73) (69-84) (70-73) (96-99) (ALL) (ALL) (87) (2007) (2007) (99-06) (00-06) (97-99) (91-99) (80-96) (97-03) (97-02) (01-06) (88-00) (84-87) (80-83) (82) (75-79) (93-99) (76-78) (90/94) (88-91) (ALL) (93-06) (87-03) (89-90) (86) (87) (ALL) (ALL) #3561 #3561 #3561 #3561 #3561 #4989 #4989 #3561 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #3591** #3591 #3591 #3591 #4989 #4989 #3561 #3591 #2528 #2528 #3591 #2528 #3591 #3560 #2528** #2528** #2528 #3560* #3560* #3560* #3560* #3560* #2519* #3560* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* PC680 PC680 PC680 PC680 PC680 PC925L PC925L PC680 PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC545MJ PC545MJ PC545MJ PC545MJ PC925L PC925L PC680 PC545MJ PC545 PC545 PC545MJ PC545 PC545MJ PC680MJ PC545 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 cc model (year) cat. # mfg sku # KAWASAKI 1500 1500 1300 1000 1000 900 900 750 750 650 636 600 600 KTM 640 620 400 400 MOTO GUZZ I 1100 1100 1100 1000 1000 850 850 750 650 650 650 500 POLARIS All SUZUKI 1400 900 750 750 750 650 600 600 600 600 400 TRIUMPH 600 YAMAHA 1600 1300 1300 1200 1100 1100 1100 920 600 600 VN 1500-A Vulcan VN 1500-C Vulcan KZ 1300 Touring KZ 1000-P Police Z1000 ZX900-C, Ninja ZX900-E, F Ninja KZ750-L, Ninja Zx750 Ninja ZX, 7RR KLX650C, R ZX636-B Ninja ZX-6R ZX600-G, J Ninja ZX ZX600-K Ninja ZX Adventure, Duke, RXC Adventure, Duke, LC4 LC4 E/XC RXC LC4 Cali/Spc/Jackl/Stone/EV Quota/Sport 1100 VII EV/Bassa California III,Quota,Millie Convert,Daytona, LeMans LeMans T3, T4, T5 Nevada,NTX,Strada,V7,V75 NTX V65 V65 Florida V50 Victory GV 1400GC RF900, R, S, ZS GSX750F Katana GSX-R750 GSXR750W DR650SE GSF600S Bandit GSX600F Katana GSX-R600 RF600R, S GSF400 Bandit Daytona 600 XV 1600 Road Star 1300 Royal Star XVZ Venture Royale XVZ12T Venture XJ1100 Maxim XS 1100, L, S XV 1100, S/ Virago XV 920/R/M Virago XJ600S Seca II XT600E (87-98) (96-97) (79-82) (82-05) (03-04) (98-99) (00-04) (93) (91-97) (93-96) (03-04) (98-02) (03) (99-02) (96-98) (96-98) (96-01) (94-05) (97-02) (98-99) (ALL) (86-88) (94-97) (98-03) (96-99) (94-95) (96-04) (96-03) (98-04) (97-03) (94-96) (91-93) (03-04) (99-03) (96-03) (86-92) (83-85) (82) (78-92) (86-99) (81-83) (92-98) (90-95) #3560 #3560 #3560 #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #4989 #2528 #4989 #4989 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #4989 #2519* #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2528*** #2528*** #3560 #3560 #3560 #3560 #3560 #3560 #2519* #2519* PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC925L PC545 PC925L PC925L PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC925L PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310

Incoming search terms:

Kawasaki 900/1100 Billet Head Installation And REMOVAL Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Remove stock head and clean the top surface of the cylinder. 2) Remove the stock water fitting from the stock head and install it in the ADA Racing® billet head in the center cylinder location. Install the 1/8″ npt brass plugs in the 2 outer cylinder locations. 3) Install all o’rings in the ADA Racing® billet head, use small amounts of grease to hold them in place, do not use super glue or silicone. 4) Apply a small amount of grease to the small (OR020) o’ring at the top of the dome. This will allow the dome to easily slip into the head shell. Be careful when turning the head upside down to install onto the cylinder, as the domes can slide out of the head shell. 5) Make sure all the o’rings are in place and place the head on top of the cylinder with the water outlet on the intake side. You must be sure that none of the o’rings slip out of their groove, as this will cause an o’ring to get pinched and a water or compression leak could result. 7) Torque all of the nuts to 15ft/lbs, in a center-out criss-cross pattern. Now, torque them again to 18ft/lbs. 8) After the 1st time out riding the head should be re-torqued. 9) The 2 additional 1/8″ npt holes in the ADA Racing® billet head come with brass plugs, but barbed fittings can be installed for custom water routing applications.

Incoming search terms:

Kawasaki 900 / 1100 Engine Removal and Installation

0

Filed Under (Kawasaki) by admin on 01-05-2012

download
1.1 (Above) Remove the two retaining straps, disconnect the battery and remove it from the hull. Disconnect the negative (black) cable first, then the positive (red). Step 2 Intake Removal 2.1 (Below) Remove the eight 10mm bolts securing the flame arrestor cover to the base and remove it. 2.2 (Below) Pull out the flame arrestor screens. 2.3 (Below) Remove the six 10mm bolts securing the flame arrestor base and carbs to the manifold and remove the base. 2.4 (Below) Loosen the gas tank cap to relieve pressure. Be sure the fuel switch is turned to the “OFF” position, and be aware of any fuel that may spill from the hoses. Make sure the hull is clear of any gasoline fumes before continuing work, especially with power tools. Remove the pulse lines from the block, and the three oil lines from the carbs. Move the carbs aside in the hull. 2.5 (Below) Remove the 18 10mm nuts from the studs securing the intake manifold to the engine and remove the manifold

Incoming search terms:

Installation Instructions for TRD’s 3.4-liter V6 Supercharger Kit 1997-2000 Tacoma,1997-1998 T-100, 1996-2000 4Runner

0

Filed Under (Toyota Manuals) by admin on 28-05-2011

Download

begin, TRD recommends you thoroughly Before you and engine compartment.thatyou don’t, grease clean the engine
If buildup  on parts could become dislodged during the procedure and fall into the engine.
• Make sure the engine has cooled fully before you begin. suggest you draw diagrams of your
• To help you later, we you disconnect anything. You can doengine’s cable routing before the same

for the vacuum hoses; however, some of the vacuum connections on your stock manifold may not be the same as those on the supercharger. To ensure the proper hose connections, refer to the diagrams in the back of this manual.
TRD supercharger has been designed to reuse most of • Thestock nuts and bolts.kitTherefore, as you remove them, keep the  them with their components or label them for location. This will assure a faster, easier installation.
B. Removal of Stock Intake Manifold (figure 1)
1. Disconnect the battery ground cable.
2. With tape or a permanent marker, mark the forward edge of the power steering and the air conditioning compressor drive belts (figure 2). This will ensure that the belts will be returned to their original positions and that they will rotate in the same direction. If you reverse the direction of rotation, it may cause the belts to fray.

Incoming search terms:

Incoming search terms: