Filed Under (Harley Davidson) by admin on 07-03-2011
INSTALLATION 1. See Figure 1. Install the oil cooler (2) to the frame with three clamps (4), three socket head screws (1), three nuts (5) and six washers (3) from the kit. Orient the clamps flat side forward and on the forward side of the oil cooler. Tighten the three oil cooler mounting screws to 96-120 in- lbs (10.9-13.5 Nm) . 2. See Figure 2. Remove the spin-on oil filter and oil filter adapter (1) from oil filter mount location. Clean the oil filter mounting area thoroughly. Discard oil filter and adapter. 1 3 4 4 4 3 5 2 is03387 1. Socket head screw (3) 2. Oil cooler 3. Washer (6) 4. Clamp (3) 5. Locknut (3) Figure 1. Oil Cooler Clamp Installation NOTE The oil cooler adapter assembly has two flanges protruding out of the back side. The flanges must be installed toward the oil filter mounting location and through the oil adapter gasket. 3. See Figure 3. From the kit, install the oil cooler adapter gasket (3) onto the oil cooler adapter assembly (1). The oil cooler adapter assembly flanges should be aligned so it is installed into the oil adapter cooler gasket cutout as shown. NOTE Due to the locating flanges, the oil cooler adapter assembly and gasket will only install properly in one position on the oil filter mounting surface. 4. See Figure 3. Install the oil cooler adapter assembly and gasket onto the oil filter mounting surface of the engine with the mounting fitting (2). Ensure adapter locates properly in the mounting surface. Ensure the raised lip of the mounting fitting faces the adapter assembly. Tighten mounting fitting to 12-16 ft-lbs (16.3-21.7 Nm) .NOTE Slide hose clamps from the kit onto the hoses prior to installa- tion. 1 2 is00754 1. Oil filter adapter 2. Oil filter seal surface Figure 2. Stock Filter Mounting Adapter 1 2 3 is00761 1. Oil cooler adapter assembly 2. Mounting fitting 3. Oil cooler adapter gasket Figure 3. Install Oil Adapter 5. See Figure 5. Obtain the left side cooler hose (4) and right side cooler hose (5) from kit. Follow the markings on hoses to connect onto the oil cooler and oil cooler adapter, as shown. 6. Fasten hoses to oil cooler adapter and oil cooler with worm drive clamps (6). Tighten clamps to 8.0 in-lbs (0.9 Nm) . 7. Lubricate a new oil filter’s seal with new engine oil. Thread filter on until seal touches mounting surface, then turn an additional 1/2 to 3/4 turn. NOTE Position the clamps to avoid interference with oil filter installation. Check that hose routing is clear of the oil filter and sharp edges. The hoses must be free of bends or kinks that could obstruct oil flow. 8. Ensure all cables and harnesses are clear of the oil cooler adapter, in order to prevent wear. 9. Thoroughly clean the oil cooler of all dirt, grease and wax with isopropyl alcohol. Use the alcohol to clean the chrome oil cooler cover as needed. Allow to dry. is00745 Figure 4. Apply Sealant Inside Chrome Cover 10. See Figure 4. Apply sealant to the inside of the chrome cover as shown, at the upper and lower corners. NOTES Be careful to avoid getting sealant on the oil cooler cooling fins. Do not operate the motorcycle for 24 hours to allow the sealant to fully cure. 11. Slip the cover over the oil cooler. Remove any excess sealant from the front and back of the oil cooler. Hold the cover firmly in place for one minute. System Flow Test 2005 & Later Models or Models with Later Style Dipsticks Oil level cannot be accurately measured on a cold engine. For pre-ride inspection, with motorcycle leaning on jiffy stand on level ground, oil should register on dipstick between arrows when engine is cold. Do not add oil to bring the level to the FULL mark on a COLD engine. (00185a) 2004 & Earlier Models
Filed Under (Toyota Manuals) by admin on 03-10-2011
Action Date Mileage Day Cost (with tax) By Interval Notes Oil and Oil Filter Change 8/30/1999 2494 Monday$77.97 Dealer 2494Non-synthetic 5w-30 (Toyota dealer stock) Oil and Oil Filter Change 10/31/1999 5484 Sunday $30 Owner 2988.5Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 12/30/1999 8460 Thursday$30 Owner 2975.9Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 2/21/2000 11414 Monday $30 Owner 2953.3Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 4/22/2000 14479 Saturday$30 Owner 3065.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 7/4/2000 17339 Tuesday$30 Owner 2860.1Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Air Filter – Replace 7/4/2000 17339 Tuesday$15 Owner 17339Purolator A24690 Air Filter Oil and Oil Filter Change 9/16/2000 20161 Saturday$30 Owner 2821.9Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Transmission Drain and Fill 10/27/2000 21913 Saturday$15 Owner 21913Drain and Fill 2.5 Quarts Mobil 1 Dexron III Synthetic ATF Transmission Drain and Fill 10/28/2000 21920 Sunday $15 Owner 7Drain and Fill 2.5 Quarts Mobil 1 Dexron III Synthetic ATF Oil and Oil Filter Change 11/19/2000 23066 Sunday $30 Owner 2904.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 2/11/2001 26062 Sunday $30 Owner 2996.1Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Transmission Flush 4/30/2001 28351 Monday$135 Dealer 2835113 Quarts Mobil 1 Dexron III Synthetic ATF – TransTech Flush Tires – Rotate 5/12/2001 28766 Saturday$0 Dealer 28766Tires – Rotate Coolant Flush 5/12/2001 28766 Saturday$112 Dealer 28766Toyota Red Coolant + MOC Flush (Extended warranty with service) Oil and Oil Filter Change 5/13/2001 28793 Sunday $30 Owner 2730.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Air Filter – Replace 5/13/2001 28793 Sunday $15 Owner 11454Purolator A24690 Air Filter PCV Valve – Replace 5/26/2001 31083 Saturday$10 Owner 31083Toyota OEM PCV Valve Windshield Wipers – Replace 5/26/2001 31083 Saturday$10 Owner 31083Windshield Wipers – Replace Oil and Oil Filter Change 5/27/2001 31296 Monday $30 Owner 2502.8Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 9/15/2001 34374 Saturday$30 Owner 3078.5Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Tires – Replace 9/28/2001 34784 Friday$431.23 Dealer 34784 (4) Bridgestone RE950 Tires (2 of original tires had tread separation – ~30% tread remaining) Oil and Oil Filter Change 11/12/2001 37365 Monday $30 Owner
Filed Under (Harley Davidson) by admin on 20-02-2011
INSTALLATION 1. See Figure 1. Remove the spin-on oil filter (2) and oil filter adapter (1) from oil filter mount location. Clean the oil filter mounting area thoroughly. Discard oil filter adapter. NOTE The oil adapter assembly has two flanges protruding out of the back. The flanges must be installed toward the oil filter mounting location and through the oil adapter gasket. 2. See Figure 2. Install the oil adapter gasket (3) onto the oil filter adapter assembly (1). The oil adapter assembly flanges should be aligned so they are installed into the oil adapter gasket cutout as shown. 1 2 is00602 1. Oil filter adapter 2. Oil filter Figure 1. Oil Filter and Adapter 1 2 3 5 4 is00761a 1. Oil cooler adapter assembly 2. Mounting fitting 3. Oil cooler adapter gasket 4. Gasket adhesive side 5. Oil cooler adapter assembly gasket surface Figure 2. Install Oil Adapter
Filed Under (Harley Davidson) by admin on 01-02-2011
LCD DIPSTICK INSTALLATION 1. Remove the original equipment (OE) dipstick from the filler neck. 2. Non-threaded Dipsticks: Lightly oil the O-ring on the new LCD dipstick. Orient the dipstick so that the display window is horizontal and readable from left to right, with the Bar and Shield logo to the left (towards the rear of the motorcycle). Push the dipstick straight into the filler neck until it seats. 3. For threaded dipsticks: Lightly oil O-ring and screw into the transmission like OE dipstick. If the orientation of the display is unsatisfactory when fully seated, refer to Adjusting the Display Angle later in these instructions. NOTE To be sure of correct readings, the dipstick MUST seat firmly against the flange. LCD DIPSTICK USE AND CARE Removing the Dipstick The dipstick assembly must be removed from the filler neck to add oil or to service the internal battery. Displaying the Oil Temperature and Level See Figure 1. Press and release the rubber button on the front face to display the temperature of the oil in the oil tank in degrees Fahrenheit (°F), and the oil level. The display will automatically shut off after approximately ten seconds. Do not overfill oil tank. Doing so can result in oil carryover to the air cleaner leading to equipment damage and/or equipment malfunction. (00190a) NOTES Oil level cannot be accurately measured: • on a cold engine • with the motorcycle upright • with the engine running NOTE Oil level on 2000 through 2004 Softail models with the original dipstick is checked with the motorcycle standing upright (not leaning on the jiffy stand). THIS IS NOT THE CASE with the LCD oil temperature/level dipstick. For all 2000 and later Softail models, oil level inspection must be done with the motorcycle LEANING ON the jiffy stand, on level ground. For pre-ride oil level inspection: With the motorcycle on level ground, RESTING ON the jiffy stand : •The oil level should be as indicated in Figure 1, display 4 through 8 (bars showing oil level, and “COLD OIL” message followed by flashing oil temperature) when the engine is cold. DO NOT ADD OIL to bring the level to the FULL mark on the dipstick of a COLD engine. •If the oil level indicates as in display 9 (animated level bars, followed by an “888 NO SENSOR” code), the wires inside the dipstick may be disconnected or damaged. Refer to Replacing the Battery later in these instructions to separate the dipstick upper and lower assemblies. If the small plug next to the battery has become dislodged from the receptacle, plug it in. If a visible wire is damaged, a repair can be attempted. If no damage is visible, the dipstick is damaged internally and should be replaced. For oil level inspection at operating temperature: Ride the motorcycle until the engine is at normal operating temperature. Idle for 1-2 minutes with the motorcycle on level ground, RESTING ON the jiffy stand (except Softails) , turn the engine OFF.
Filed Under (Wildfire) by admin on 29-11-2010
Engine Oil Replacement • Replace the engine oil after the first 50 miles or 1 hour with 5w50, 10w50 or 15W50 synthetic engine oil. Then replace again every 1,500 miles or 1 each year. Check oil level every 500 miles, add oil if needed. Changing the Engine Oil (1).Warm up the engine for a few minutes. (2).Stop the engine. (3). Place scooter on center stand. (4).Place an oil pan under the engine and remove the dipstick. (5).Remove the drain plug and drain the oil. Reach in drain hole, pull out filter clean and reinstall, after all oil drains out. (6).Reinstall drain plug. (7). Fill the engine with oil until the level is in the designated area on the dipstick. (8).Start the engine and check for oil leaks. If a leak is found stop the engine immediately and look for cause. Rear Wheel Oil Replacement • Replace the gear oil after the first 500 miles with 5W/50 synthetic engine oil. Replace the gear oil again every 4 months or every 2000 miles. • Replacing the Gear Oil (1).Put the scooter on the center stand (please see photo below) . (2).Place an oil pan under the gear case (please see photo below) . (3).Remove the oil filler bolt and the drain plug to drain the oil (please see photo below) . (4).Reinstall and tighten the drain plug. (5).Fill the gear case with oil (please see photo below) . (6).Reinstall the oil filler bolt. (7).Check for oil leakage. Cleaning Air Cleaner Be sure to check the air cleaner regularly. (1).Place the scooter on the center stand. (2).Unscrew and remove the left side panel. (3).Remove the air cleaner cover by removing the screws. (4).Take out the air cleaner by removing the screws. (5).Remove the air cleaner element and wash it gently, but thoroughly in solvent. Replace if damaged. (6).Squeeze out the excess solvent and dry it. (7).Apply oil to the entire surface of the air cleaner and squeeze out the excess oil. It should be damp but not dripping. (8).Install the air cleaner, cleaner cover, and left side panel. center stand 1 oil pan 2 3 oil drain plug oil pan 5 Main Switches On Position: • Electrical circuits are switched on. The engine can be started and the key can not be removed.