2001 fatboy where does this hose connect

You search Auto repair manual PDF 2001 fatboy where does this hose connect, if there are search results will appear below. If search results do not exist, please search by others keyword.





Victory Freedom Engines Installation Instructions for S&S Air Cleaner Kit

0

Filed Under (Victory) by admin on 31-10-2010

download
1-Locate and remove the Intake Air Temperature Sensor (IATS) from the stock Polaris Victory air box. Locate the new position for the IATS on the bottom of the S&S air cleaner. Push the IATS in the lower air cleaner cover and turn1⁄ 4 turnin either direction, make sure you feel it lock into place. Inspect from the inside of the air cleaner to ensure that the barbs are locked into place. See Picture 1. 2-Using the stock Polaris Victory air box gasket (PN 5811908) and S&S supplied (Qty 4) M6 fasteners, assemble the lower air cleaner cover to the throttle body using 243 Blue Loctite®on the treads. Torque the M6 fasteners to 72-96 inch pounds. 3-Position the S&S pre-formed air filter onto the lower air cleaner cover ensuring that it fits into the machined groove. 4-Install the top air cleaner cover on top of the filter ensuring that it fits into the machined groove. 5-Make surethat the filter is situated in the machined grooves on both the top and bottom air cleaner covers. 6-Using 243 Blue Loctite on the threads of the S&S supplied (Qty 3) M6 fasteners tighten down top air cleaner cover evenly until seated. Finish torque the fasteners to 72-96 inch pounds. Now you’re ready for breather hose and barometric pressure hose routing. 7-Locate the S&S supplied 3⁄ 16 “reinforced hose and clamps. Push one end of the hose on the 3⁄ 16 “brass barb in the bottom air cleaner cover and slide clamp up around the end of the hose. The other end of the hose is for the Barometric Pressure Sensor (MAP). Route the hose towardthe back of the engine over the top of the rear rocker cover. 8-Remove the MAP sensor from the stock Polaris Victory air box. Remove the orange rubber gasket from the MAP sensor. Slide the S&S supplied clamp over the 3⁄ 16 “rubber hose that leads to the air cleaner. Push the barbed end of the MAP sensor into the 3⁄ 16 ” rubber hose and slide clamp up to the end of the hose around the barb. A small amount of lubricant may be applied to the barb on the MAP sensor to make installation easier. 2 S&S Air Cleaner Assembly 41-0021 (Calibration cardnot shown) Picture 1 CAUTION WARNING WARNING Plastic barb locked in recess.
9-Assemble and install breather hose as follows: A-Cut the stock Victory®hose on the straight section just behind the 90 degree bend as shown in Picture 2 . B-Slide an S&S supplied 1⁄ 2 “hose clamp over the modified stock breather hose. C-Install the S&S straight barb in Victory breather hose and position a hose clamp around hose end. D-Slide the 90-degree end of breather hose over the brass barb on the air cleaner cover and slide hose clamp in place. E-Position straight end of the S&S breather hose over the 1⁄ 2 “barb to connect to the Victory hose. Slide clamp over connection. F- See Pictures 3 and 4 for breather hose and barometric pressuresensor hose installation positions. NOTE: S&S breather hose can be cut for best fit

Incoming search terms:

HONDA VTX1300 AIR HORN INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Remove the rider and passenger seats, left chrome side cover & original horn located at the top of the radiator. 2. Locate the supplied black horn mounting bracket and supplied smaller hose clamp. Notice the slight twist in the bracket. Using 2 adjustable wrenches or a vise and one wrench remove the twist from the bracket. Route the hose clamp thru the bracket. (As shown in photo 1A) 3. Install the bracket on to the left frame tube, (As shown in photo 1A) and tighten securely. Bolt the supplied horns to the bracket using the supplied bolt, lock washer and nut, (As shown in photo 1) and tighten securely. Install the supplied trumpet covers (As shown in photo 1B) by flexing the spring clips over the trumpets. Check that they fit securely. If not remove covers, make sure the center screw is tight and bend spring clips in towards center of covers and re-install. Using a blade screwdriver pry the two supplied hoses with the “Y” connector off of the air horns cut a new piece of hose 3 ½” long from the hose and replace the short hose on the “Y”. Re-install the “Y” hose assembly with the short hose going on the long or upper trumpet. (See photo 1C) Re-route the original horn wires. (As shown in photo 1D) 4. From the supplied wire cut 2 pieces 28″ long. Strip ¼” of insulation from both ends. Crimp 2 supplied male terminals to one end and 2 supplied female spade terminals to the other end. Plug the male ends into the original horns wires. (As shown in 1D) Attach the remaining air hose to the “Y”. Tape the hose and wires together every 6-8″ using electrical tape to make routing easier and neater. Route the wires and hose up under the fuel tank, over the cylinder heads coming out between the frame rails at the rear of the fuel tank. (See photo 2A) Locate the supplied relay and plug the 2 wires from the original horn onto terminals 85 & 86 on the relay. (See wiring diagram on back of last page of instructions) This will be the 2 outer terminals that are parallel to each other. Locate the supplied fuse, holder & wire assembly. Crimp a supplied fork terminal to one end and a supplied female spade to the other. Attach the spade terminal to one of the remaining outer relay terminals. (#30 or 87 on wiring diagram) Remove the 3 Phillips screws from the battery top cover. Remove the cover and attach the fork end of the fuse wire to the positive (+) terminal. Re-install the battery cover. 5. Cut a wire 9″ long and strip ¼” insulation from each end, crimp a fork to one end and a female spade to the other. Attach this wire to the compressors negative (-) terminal. Cut another wire 18″ long and strip both ends. Crimp a female spade to both ends. Attach this wire to the compressor positive (+) terminal. Route the air hose out under the left side cover as shown in photo (3). Hold the compressor in place against the frame tube. Note: Looking at the large end of the compressor the space between the hose fitting and the bolt mounting flange forms a “V” shape. This is where the compressor should rest against the frame. Next loop the hose around to the compressor hose fitting and trim the hose to the desired length. Attach the hose to the compressor. Secure the compressor to the frame using 2 large supplied cable ties as shown. 6. (See photo 3A) Attach the compressor negative (-) wire to the bolt on the frame (As shown in photo 3B) Route the compressor positive (+) wire along the side up to the relay and attach to the remaining outer terminal 87 or 30. Cable tie the relay in place. (As shown in photo 2B) Use several of the supplied short cable ties to secure the compressor wires to the air hose (As shown in photo 3) as wells as any other loose wire or hose.

HARLEY DAVIDSON XL PREMIUM OIL COOLER KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Refer to Owners Manual to drain engine oil and remove oil filter. 2. See Figure 1. Remove oil feed hose (1) from oil pump. 3. Remove oil feed hose fitting from engine crankcase. Discard oil feed hose. INSTALLATION 1. See Figure 2 and Table 1. Apply Hylomar Gasket and Thread Sealant to threads of fitting (1) and install fitting to oil pump. 2. Apply Hylomar Gasket and Thread Sealant to threads of fitting (1) and install fitting to crankcase. 3. Tighten fittings to 55-65 in-lbs (6.2-7.4 Nm) . 1 2 3 1 is04015 1. Fitting 2. Oil Hose Cooler Supply 3. Oil Hose Cooler Return Figure 2. Oil Hose Cooler Return and Supply Assmeblies 4. Loosely install oil cooler return hose assembly (3) to crankcase fitting. 5. Loosely install oil cooler supply hose assembly (2) to oil pump fitting. 6. See Figure 3 for proper oil hose routing. The oil supply hose (1) should be the upper hose and the oil return hose (2) the lower hose 1 2 is04018 1. Oil Supply Hose 2. Oil Return Hose Figure 3. Oil Cooler Hose Routing 7. Remove two existing clips holding the clutch cable and wire harness from the left frame downtube. 8. See Figure 4 and Table 1. Position oil cooler clamps (7) in approximately the same position as the clips that were removed from the frame downtube. 9. Loosely attach oil cooler (4) to the clamps (7) using screws (9) and nuts (8). 10. Attach oil return hose (3) to the inboard connection of oil cooler (4) with worm clamp (5).

HONDA VTX 1800 AIR HORNS AHVTX INSTALATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 23-12-2010

download
1. Remove the right and left frame side covers and the seat. 2. Unplug and remove the stock horn located behind the left foot peg. Re-route the horn wires up over the front cylinder head and to the rear. Next cut two pieces of wire 36″ long, strip both ends ¼”, crimp two male spade terminals to one end and two females to the other ends. Attach these wires to the stock horn wires and route them over the rear cylinder and behind the frame tube. The end of the wires should come out near the center of the left side cover area (see photo 1 A). Connect these two wires to the relay terminals 85 & 86 (these will be the two that are parallel to each other see wiring diagram for terminal identification). 3. Using a blade screwdriver pry the two hoses with the “Y” connector off of the air horns. Cut a new piece of hose 2 ¾” long, replace the old short hose on the “Y” with this. Re-install the “Y” hose assembly onto the horns with the short hose on the long trumpet, route the hoses behind the horns and connect the long hose to the short horn (see photo 2A). 4. Remove the upper 8mm (12mm wrench size) motor mount bolt (see photo 2B). Install the horn assembly using the 8 x 55mm bolt and spacer tube provided. If the motorcycle is fitted with Honda line tubular radiator or engine guards the above mounting will not work. You will need instead to locate the “J” shaped bracket and small hose clamp provided in the hardware kit (see photo 2 on instructions of multi -application instruction sheet). Thread the hose clamp thru the bracket and attach to the frame or Honda line guards as shown ( see photos 2&3 ) tighten the hose clamp securely using a socket or wrench. Attach the horn set to the “J” bracket using the 5/16 x ¾” bolt, nut and lock washer provided. Position the horns so that they are angled down just slightly then tighten the bolt securely. Attach the remaining air hose to the “Y” connector, route the hose up over the top and to the rear of the engine. Cross the hose over to the right side of the rear cylinder head, then behind the electricals of the right side cover and coming out as shown ( see photo 3 A & B ). 5. Remove the center relay from its mounting bracket by lifting it upward and re-attach it lower and at an angle as shown (see photo 3C) using a small cable tie. Route two long cable ties thru the hole in the relay mounting bracket as shown (see photo 3D). Next cut a 16″ wire, strip both ends, crimp female spades to both ends. Attach this wire to the compressors pos (+) terminal. Cut an 8″ wire, strip both ends, crimp a female spade to one end and a fork terminal to the other. Attach this wire to the compressors neg. (-) terminal. Cable tie the compressor securely in place as shown (see photo 4). Route the hose to the compressor making sure there are no tight bends or kinks cut the hose to the desired length and attach it to the compressor. Route the neg. (-) wire with the fork terminal up and attach it to the 10 mm bolt as shown (see photo 4A) . Route the pos. (+) wire over to the relay on the left side of the motorcycle and attach it to terminal 30 or 87 on the relay (see wiring diagram)

Incoming search terms:

TOYOTA NEW SEAT BELT TONGUE PLATE STOPPER SERVICE PARTS

0

Filed Under (Toyota Manuals) by admin on 10-10-2011

download
installation procedures are provided to supplement the Repair Manual. MODEL YEAR Avalon 1995 – 2001 Camry 1983 – 2001 Corolla 1980 – 2001 Camry Solara 1999 – 2001 Sienna (Front Seat Belt Only) 1998 – 2001 RAV4 1997 – 2001 4Runner 1992 – 2001 Land Cruiser 1991 – 2001 Tundra 2000 – 2001 Tacoma 1997 – 2000 ECHO 2000 – 2001 Celica 1980 – 2001 Prius 2001 – 2001 Tercel 1981 – 1999 PREVIOUS PART NUMBERCURRENT PART NUMBER PART NAME N/A 73219-02010 Stopper, Tongue Plate (Black)* N/A 73219-02020 Stopper, Tongue Plate (Gray)* N/A 73219-02030 Stopper, Tongue Plate (Beige)* *Use a stopper color that is closest to the seat belt webbing color. OP CODE DESCRIPTION TIME OPN T1 T2 BD0047 Install Seat Belt Tongue Plate Stopper 0.1 73219-020#0 62 12 Applicable Warranty*: This repair is covered under the Toyota Comprehensive Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle’s in-service date. *Warranty application is limited to correction of a problem based upon a customer’s specific complaint

Incoming search terms:

1999 Toyota Camry LE V6 Body and Interior Maintenance Record

0

Filed Under (Toyota Manuals) by admin on 03-10-2011

download
Action Date Mileage Day Cost (with tax) By Interval Notes Oil and Oil Filter Change 8/30/1999 2494 Monday$77.97 Dealer 2494Non-synthetic 5w-30 (Toyota dealer stock) Oil and Oil Filter Change 10/31/1999 5484 Sunday $30 Owner 2988.5Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 12/30/1999 8460 Thursday$30 Owner 2975.9Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 2/21/2000 11414 Monday $30 Owner 2953.3Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 4/22/2000 14479 Saturday$30 Owner 3065.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 7/4/2000 17339 Tuesday$30 Owner 2860.1Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Air Filter – Replace 7/4/2000 17339 Tuesday$15 Owner 17339Purolator A24690 Air Filter Oil and Oil Filter Change 9/16/2000 20161 Saturday$30 Owner 2821.9Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Transmission Drain and Fill 10/27/2000 21913 Saturday$15 Owner 21913Drain and Fill 2.5 Quarts Mobil 1 Dexron III Synthetic ATF Transmission Drain and Fill 10/28/2000 21920 Sunday $15 Owner 7Drain and Fill 2.5 Quarts Mobil 1 Dexron III Synthetic ATF Oil and Oil Filter Change 11/19/2000 23066 Sunday $30 Owner 2904.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 2/11/2001 26062 Sunday $30 Owner 2996.1Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Transmission Flush 4/30/2001 28351 Monday$135 Dealer 2835113 Quarts Mobil 1 Dexron III Synthetic ATF – TransTech Flush Tires – Rotate 5/12/2001 28766 Saturday$0 Dealer 28766Tires – Rotate Coolant Flush 5/12/2001 28766 Saturday$112 Dealer 28766Toyota Red Coolant + MOC Flush (Extended warranty with service) Oil and Oil Filter Change 5/13/2001 28793 Sunday $30 Owner 2730.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Air Filter – Replace 5/13/2001 28793 Sunday $15 Owner 11454Purolator A24690 Air Filter PCV Valve – Replace 5/26/2001 31083 Saturday$10 Owner 31083Toyota OEM PCV Valve Windshield Wipers – Replace 5/26/2001 31083 Saturday$10 Owner 31083Windshield Wipers – Replace Oil and Oil Filter Change 5/27/2001 31296 Monday $30 Owner 2502.8Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 9/15/2001 34374 Saturday$30 Owner 3078.5Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Tires – Replace 9/28/2001 34784 Friday$431.23 Dealer 34784 (4) Bridgestone RE950 Tires (2 of original tires had tread separation – ~30% tread remaining) Oil and Oil Filter Change 11/12/2001 37365 Monday $30 Owner

Incoming search terms:

2001-2002 GL1800 A ABS Speed Sensor Wire Clamp Location INSPECTION/ REPAIR PROCEDURES

0

Filed Under (Honda) by admin on 29-01-2011

download
1. If the VIN is within the preceeding range, inspect the front ABS speed sensor wire clamp according to the following illustrations. 2001-2002 GL1800A ABS Speed Sensor Wire Clamp Location INCORRECT Installation CORRECT Installation Service Bulletin American Honda Motor Co., Inc. 2001-2002 GL1800 ABS Speed Sensor Wire Clamp Location 0112 GL1800 #9*GL1800 #9*0112*2001-2002 GL1800 ABS Speed Sensor Wire Clamp Location*GL1800, ABS Speed Sensor Wire Clamp Location*Motorcycle*1800 2 of 2 ©2001 American Honda Motor Co., Inc. – All Rights Reserved GL1800 #9 DECEMBER 2001 IDENTIFICATION There is no identification mark associated with this Service Bulletin. PARTS INFORMATION There is no parts information associated with this Service Bulletin. WARRANTY INFORMATION The normal warranty claim submission requirements apply. Submit one warranty claim per VIN with the following information only: Inspected and REPAIRED Template: GL#9 Hours: 0.2 hours Parts: None If the clamp is installed correctly on top of the speed sensor, no further action is necessary. 3. If the clamp is installed incorrectly under the speed sensor, remove and reinstall the clamp and speed sensor correctly. Torque the bolts,. Torque: 12 N • m (1.2 kgf • m, 9 lbf • ft) If the speed sensor wire clamp for the front ABS speed sensor is installed incorrectly, the ABS speed sensor air gap may be out of specification. This does not affect ABS speed sensor operation, but the clamp should be installed correctly. Inspect and repair all affected units using the Inspection/Repair procedures listed below. Inspect all unsold units and customer units brought in for service. AFFECTED UNITS 2001-2002 GL1800A units as follows: MODEL 2001 GL1800A All units 2002 GL1800A 1HFSC474*2A100001 – 1HFSC474*2A101643 * = denotes check digit Any unit in the above VIN range may be affected and should be inspected according to the procedures in this Service Bulletin. All units outside of the above VIN range do not require inspection. CUSTOMER NOTIFICATION There is no customer notification associated with this Service Bulletin.

Incoming search terms:

2007 Softail HARLEY DAVIDSON FUEL PUMP/ FUEL GAUGE SENDING UNIT REMOVAL AND INSTALLATION

0

Filed Under (Harley Davidson) by admin on 30-03-2012

download
1. Remove seat. 1 WARNING 1 WARNING To prevent spray of fuel, purge system of high-pressure fuel before supply line is disconnected. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00275a) 2. Purge the fuel supply line of high pressure gasoline. a. See Figure 4-36. Disconnect the fuel pump fuse from the main wiring harness. b. Start the engine and allow the vehicle to run. c. When the engine stalls, operate the starter for 3 seconds to remove any remaining fuel from the fuel lines. 1 WARNING 1 WARNING To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 3. Disconnect negative battery cable. 4. Remove instrument console. a. All but FXSTD, see Figure 4-37. Remove acorn nut and washer on instrument console to separate console from fuel tank. b. For FXSTD, see 8.26 INSTRUMENT CONSOLE: FXSTD. 5. Disconnect console wiring. Figure 4-36. Fuel Pump Fuse: View From Top Figure 4-37. Acorn Nut And Washer: All But FXSTD s0660x8xx 7526
4-28 2007 Softail: Fuel System HOME 1 WARNING 1 WARNING Gasoline can drain from the crossover line when disconnected from fuel tank. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00259a) 6. Drain fuel tank. a. Obtain a short section of hose (5/16 inch I.D.). Insert bolt in one end of hose and install hose clamp to ensure that end is securely plugged. b. See Figure 4-38. Cut clamp (1) from one end of crossover hose (2). Quickly replace crossover hose on fuel tank fitting with open end of short hose while directing flow of gasoline from free end of crossover hose into suitable container. 7. See Figure 4-39. Unplug fuel pump module connector (3) [86]. 8. Remove top plate screws (2) and discard. 9. See Figure 4-40. Pull top plate (2) out of fuel tank enough to expose fuel hose and clamp (1). CAUTION Carefully inspect end of hose for cuts, tears, holes or other damage. Replace hose if any damage is found. Even the smallest hole can cause a reduction in fuel pressure. 10. Cut clamp and remove hose from regulator housing fit- ting.

Incoming search terms:

Air Shock Installation Instructions

0

Filed Under (Tips and Review) by admin on 24-11-2010

download
Air HoseInstallation. Choose the most convenient loca- tiononyour motorcycle for the air fill valve. Drilla 5/16″hole and install the air fill valve as shown in Figure 3orsecure air fill valve to frame tube. 2. Keep hose ends clean during installation because dirt can cause air leaks. 3. Install hose connector, tube clamp and two O-rings onto one end of the air hose (See Figures4&5) Apply rubber lubricant (soap solution, not oil) to the O-rings to ease installation on the air hose& into the shock absorber inlet. Plastic connector should just bottom on fitting. Do not overtighten! The function of the nut is to hold everything together in place, the O- rings do the sealing. Fin- gertightenonly (10 in/lb maximum). 4. After routing the air hose, trim the length to fit air fill valve. Install hose connector, tube clamp, and twoO-rings onto end of hose (See figures 4&5). Lubricate as above and assemble to air fill valve. Use the same procedure formating hose. Important —leaveasmall amount of slack in hose near shock absorber to allow for the slight move- mentofthe shock. Caution! Do not install hose near ex- haustsystem, battery or any other sharp edges or seat movement. Keep hoses clear of moving parts such as wheels or suspension components. Do not allow hoses to have excess slack and sag below the motorcycle. The hoses could catch on road surfaces or debris and could be damaged while the motorcycle is in motion. 5. If necessary the air hose can be secured along the motorcycle’swiringharness with tie-wraps. 6. Testing: Inflate system to 50 psi. Apply soapy water solution to all connections and check for air leaks. If there are any leaks, disconnect the suspected fitting and check for dirt or damage to the air line or the O-rings. Remove any dirt or foreign matter, re-lubricate the O-rings and reinstall. If unable to locate the leak, remove rubber boot from shocks and submerge pressurized components under water (in- cludingT-Valve) and check for leaks. If you cannot solve the air leak problem, please contact our technical staff for assistance

Incoming search terms:

2006 Kawasaki Ninja 650R DOT Racer Front Brake Hose Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove factory brake hoses, noting routing. Cap off master cylinder and caliper ports. 2. Install straight-bent banjo ends of Russell Left and Right hoses onto their respective calipers. Use factory single-banjo bolt from master cylinder to install Right hose onto caliper (See Fig. 1) . 3. Route hoses up through factory wire retainers to master cylinder (See Fig. 2, view from top). Use factory double-banjo bolt to install hoses onto master cylinder. Side-bent banjo of Right hose goes next to master cylinder, points toward center of bike, and rests against stop. Orient Left hose banjo so that hose runs parallel to Right hose (See Fig. 3) . 4. Locate hoses to fender using factory plastic clips around grommets on hoses at factory mounting points (See Fig. 4, Right side shown). 5. Check hose clearance throughout entire steering and suspension travel range. 6. Bleed the system and check for leaks while applying pressure

Incoming search terms: