2002 kawasaki 650 prairie spark plugs

You search Auto repair manual PDF 2002 kawasaki 650 prairie spark plugs, if there are search results will appear below. If search results do not exist, please search by others keyword.





Kawasaki Prairie 360,650,700 ATV PLOW Plow Mounting Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Mount Installation Note: There are different hole locations on the plow mount depending on the bike model. For Prairie 360 use the middle hole locations (B), for Prairie 650 and Twin Peaks 700 use hole locations (A) on mounting plate, as shown in Figure 1. Figure 1 Hole Locations WARN INDUSTRIES PAGE 3 67954 Rev A3 To install the plow mount to the underside of the vehicle install the front two U-bolts PN 60869, and loosely tighten the 5/16″ nuts. Pull the plow mount back in the furthest position and then fully tighten, as shown in Figure 2. For the Kawasaki Prairie 360 use the second set of U-bolts PN 61262 and securely tighten around the frame in hole location (B) . For Kawasaki Prairie 650 and Suzuki Twin Peaks 700 drill a 3/8″ hole through the aluminum skid plate, using the plow mount as a template, as shown in Figure 3. Repeat the same process on the other side. After both holes are drilled attach the mounting plate with the second set of U-bolts PN 61262 and securely tighten around the frame in hole location (A) . Tighten all fasteners securely. Torque 5/16″ Bolts: 20ft. lb.

Incoming search terms:

Kawasaki Prairie 650 Snorkel REMOVAL AND INSTALLATION

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Remove plastic from around air filter housing. Remove air filter housing lid and air filter. Remove 8 small screws from bottom of air box. Next, remove bolt from front and rear of air box. Remove the air box. Remove old snorkel from air box. Remove hose clamp and rubber drain tube from old snorkel. Reinstall on new snorkel. Install new snorkel vertical with the air box. Reinstall air box making certain all vacuum hoses are reinstalled. Check for clearance around new snorkel. Make sure all wires and steering stem do not come into contact with the snorkel. Adjust as necessary Reinstall filter and filter cover. Jetting depends on your elevation. A good starting point for 1000 feet and under is to remove the main jet #142 from the rear carburetor. Install it in the front carburetor. Purchase and install a #145 main jet in the rear carburetor. This works well with an aftermarket air filter and exhaust. For a very reasonable price, HMF Exhaust offers a jet kit with their exhaust that we recommend. Let them know Diamond G Racing sent you.

Kawasaki 650/360 Prairie Lift Kit Installation and removal Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Place jack under center of ATV front end and lift until front wheels clear the ground. Be careful to support ATV properly so that it is securely supported but so that A-arms and shocks can droop to full extension. 2) Remove front wheels. 3) Remove or loosen front plastic. 4) Remove C-clip and nut at the top of the strut. 5) Screw bracket “A” on top of strut to the same torque specifications as the nut. 6) Place the top adapter “A” through the top of the strut mount, and screw the original nut on the top of bracket “A” securing it to the strut mount. Tighten this nut to the required manufacturer specifications and replace the factory C-clip. 7) Repeat the procedure for the other side. 8) Install the wheels, torque wheel lug nuts to manufacturer’s specifications, lower and remove jack. Check for clearance problems or misalignment. Rear Lift 1) Place jack under ATV at the rear of the bottom skid plate and lift until the weight is off of the suspension. Be careful to secure the ATV properly so as not to fall off the jack. 2) Remove the bottom of the shock from the shock mount on the axle. 3) After removing the shock, jack the ATV up 1″-2″ further. 4) Place Bracket “B” between the shock and shock mount with the notched out ends facing downward. Insert stock bolt to secure bracket “B” to the shock mount and the shock. Fasten nut. 5) Insert the new 12x75mm Bolt to the top of bracket “B” and the shock eyelet and secure with a new 12mm nut. 6) Tighten all nuts and bolts to manufacturer’s torque specifications. 7) Install the wheels, torque wheel lug nuts to manufacturer’s specifications, lower and remove jack. Check for clearance problems or misalignment.

Single-Cylinder BMW G 650 X Model Series

0

Filed Under (BMW) by admin on 16-11-2010

download
introducing the new range of single-cylinder models, BMW Motorrad is broadening its model line-up with a clear focus on additional target groups. Proceeding from the same technical foundation, the Company has created three new motorcycles absolutely different in their features and characteristics: the G 650 Xchallenge Hard Enduro, G 650 Xmoto Street Moto, and the G 650 Xcountry Scrambler. With their outstanding product substance, their purist looks, and their exceptionally sporting riding characteristics, these single-cylinder models are filling attractive niches in the market. And through their low unladen weight of less than 160 kg or 353 lb according to the DIN standard, they offer dynamic performance for both the connoisseur and the sports-minded rider. Market launch of the new G 650 X model series is planned in good time for the beginning of the season in spring 2007. These new machines with the smallest engines in the BMW model range offer particularly the young and young-at-heart motorcycle rider exactly the right entry into the world of BMW motorcycles, but are not entry-level bikes in the conventional sense of the word: On the contrary, the G 650 Xchallenge Hard Enduro will thrill the customer who wishes to really benefit from the enormous offroad potential of his machine. The G 650 Xmoto Street Moto, in turn, with its very impressive active riding qualities, offers the genuine enthusiast a new dimension in riding pleasure. The G 650 Xcountry Scrambler, finally, stands for carefree riding pleasure and nimble performance both on the road and off the beaten track. Indeed, this unique machine is able to meet all kinds of requirements and offer virtually all riding qualities ranging from city use via country roads and small, winding lanes, all the way to offroad tracks presenting the most challenging requirements. The G 650 Xcountry therefore conveys the classic but relaxed feeling of riding a genuine Scrambler as well as the concept of “wandering” on your motorcycle into today’s world in a most modern style. And last but certainly not least, riding pleasure is guaranteed under all conditions and in every situation, since the G 650 Xcountry offers the same outstanding engine and running gear qualities as its two very sporting “sister models

Incoming search terms:

SUZUKI SV1000 PERIODIC MAINTENANCE

0

Filed Under (Suzuki) by admin on 26-02-2011

download
MAINTENANCE AND TUNE-UP PRO- CEDURES This section describes the servicing procedures for each item of the Periodic Maintenance requirements. AIR CLEANER I Inspect every 6 000 km (4 000 miles, 6 months) and replace every 18 000 km (11 000 miles, 18 months) . • * Remove the seat. (LF6-7) • * Lift and support the feul tank . (C-74-65) • * Remove the air cleaner box cap O. • * Remove the air cleaner element O. • * Carefully use air hose to blow the dust from the cleaner ele- ment. CAUTION Always use air pressure on the throttle body side of the air cleaner element . If air pressure is used on the other side, dirt will be forced into the pores of the air cleaner element thus restricting air flow through the air cleaner element . PERIODIC MAINTENANCE 2-5 2-6PERIODIC MAINTENANCE • * Reinstall the cleaned or new air cleaner element in the reverse order of removal . CAUTION If driving under dusty condition, clean the air cleaner element more frequently. The surest way to accelerate engine wear is to use the engine without the element or to use a ruptured element. Make sure that the air cleaner is in good condition at all times. Life of the engine depends largely on this component! NOTE: When cleaning the air cleaner element, drain water from the air cleaner by removing the drain plug . SPARK PLUG Inspect every 6 000 km (4 000 miles, 6 months) and replace every 12 000 km (7 500 miles, 12 months) . No. 1 (FRONT) SPARK PLUG REMOVAL • * Remove the radiator mounting bolt O. • * Move the radiator forward. • * Remove the spark plug cap O. NOTE: Be careful not to damage the radiator fins . A WARNING The hot radiator and the hot engine can burn you . Wait until the radiator and the engine are cool enough to touch . • * Remove the spark plug with a spark plug wrench. 1 6 I It No. 2 (REAR) SPARK PLUG REMOVAL • * Remove the seat. (r–,-6-7) • * Lift and support the fuel tank . (=4-65) 4-65) • * Disconnect the camshaft position sensor 1O and breather hose (Z. • * Remove the rubber heat shield ® . • * Remove the spark plug cap . • * Remove the spark plug with a spark plug wrench . HEAT RANGE • * Check to see the heat range of the plug . CARBON DEPOSIT •Check to see if there are carbon deposits on the plugs . If carbon is deposited, remove it with a spark plug cleaner machine or carefully using a tool with a pointed end . SPARK PLUG GAP • * Measure the plug gap with a thickness gauge . If out of specification, adjust it to the following gap . 09900-20803 : Thickness gauge Spark plug gap OA Standard: 0.6 – 0 .7 mm (0.024 -0.028 in) ELECTRODES CONDITION •Check to see the worn or burnt condition of the electrodes . If it is extremely worn or burnt, replace the plug . And also replace the plug if it has a broken insulator, damaged thread . CAUTION Confirm the thread size and reach when replacing the plug. If the reach is too short, carbon will be deposited on the screw portion of the plug hole and engine damage may result

Incoming search terms:

KAWASAKI KX450F SPARK XCR SYSTEM INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 02-05-2012

download
1. Place the machine on a stable work stand. 2. If you are not familiar with removing the original exhaust refer to the owner’s manual before you start work. 3. Always allow your machine to cool down before attempting to remove the exhaust. 4. Remove the two bolts from the right side panel. Then remove the side panel. 5. Loosen the stock mid-pipe clamp, then remove the stand-off bolt and bracket bolt that supports the muffl er. 6. Remove stock muffl er and clamp from the stock head pipe. 7. Slightly loosen the stock head pipe at the cylinder head to aid in aligning the parts. INSTALLING THE NEW XCR SYSTEM 1. Installer must use supplied hardware. 2. Slide mid-pipe onto head pipe. Rotate the mid-pipe slightly to obtain proper alignment with sub-frame mount. 3. Install the supplied M8x16mm bolt through sub-frame into the stand-off mount on mid-pipe (Finger tight). 4. Slide the muffl er onto mid-pipe, align muffl er mount with the stock muffl er mount hole, and install and fi nger tighten the OEM bolt. 5. Once you have the system fully aligned, install and tighten all the bolts securely to factory specifi cations. 6. Replace the side panel and secure the mounting bolts. 7. Re-tighten stock head pipe at the cylinder head. TEST RIDING 1. When you fi rst ride the bike be aware that the characteristics are often quite different so start out slowly. TUNING 1. On the KX450F, we suggest using stock jetting based on our testing condition. These specifi cations should only be used as a guideline. Riding at different elevations or climates may require using different settings to obtain peak performance. If you need additional assistance, please refer to your Kawasaki owner’s manual. 2. To convert system from Offroad to Competition specifi cations, remove the 5mm Allen bolt and Spark arrestor. Two different Db lowering inserts are also available (see accessories section on page 2). To return the system to Offroad specifi cation re-install the Spark arrestor into the rear of the muffl er using a small amount of blue thread locking compound (Loctite® 243) re-tighten the 5mm Allen bolt (6.5 ft pounds)

Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Upgrading the Suspension on the Kawasaki ER6-F/ N

0

Filed Under (Kawasaki) by admin on 30-11-2010

download
Top fork is as removed. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Before removing the fork from the clamps on the yokes I loosened the fork top. Before removing the fork top the fork-slider was placed in a vice and the bottom bolt loosened….. … before finally being removed with the fork upside down. Because the springs were still in situ this gave sufficient tension on the damper-rod to prevent it from turning and allow the bolt to be removed. When I turned the fork the right-way up to remove the fork-top I did it over a container to catch the oil. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource All the OE components that will no longer be required. Left to right. Fork-top, spacer tube, washer, spring, damper-rod. Bottom bolts get re-used. Old and new, laid-out for comparison. The damper unit, minus spring and fork-top, drops inside the stanchion and slider. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Then the bolt goes back in, as tight as possible, to secure it. Top fork is done, second one awaits. Note the spring seat on the right, just below the spring. This drops over the damping rod after the oil has been added. The small locking-nut screws over the threaded part of the damping-rod next, all the way to the bottom. Spring drops in and then the fork-top screws on to the damping-rod as well, all the way down to the lock-nut which is used to secure it. At this point the stanchion is extended to the fork-top which is screwed in. Job done.

Incoming search terms:

ODYSSEY DRYCELL MOTORCYCLE BATTERY COMPATIBILITY

0

Filed Under (Triumph) by admin on 30-10-2010

download
BMW 1200 1200 1150 1100 1100 1000 1000 1000 1000 900 850 800 800 800 750 750 750 750 750 650 650 600 600 500 BUELL 1200 1200 1200 1000 DUCATI 860 750 500 HARLEY DAVIDSON 1570 1570 1450 1450 1340 1340 1340 1200 883 HONDA 1800 1500 1200 1100 1000 1000 900 750 750 650 650 650 600 400 200 150 150 125 K1200RS, LT R1200C R1150GS, R R1100GS/R R1100RS/T/S/LT “K” Models R100/7 100RS R100GS, R, RS, RT R90/6, R90S R850R R80GS, R80ST R80, R80RT R80/7/RT K75, RT K75C, S R75/5 R75/7 R75/6 R65 R65LS R60/5 R60/6, R60/7 R50/5 S1 Lightning X1, S3, S3T, M2 S2/T, RS1200, RR1200 RR1000 GT, GTS GT, Laguna Seca GTL, GTV, Sport FXST, FLST FXD FXD FXST, FLST FXD FXST, FLST FL/H/T/HT XL, XLH XLH, XLH GL1800, VTX1800C Gold Wing-All Gold Wing-All Gold Wing-GL1100 CBX1000, SS opt. Gold Wing-GL1000 CBR900R,RR CB750A (Hondamatic) VFR740R/ RVF750R NT650, SLR650, NX650 Vigor 650 XR650L VT600C, CD, CBR600 CBR400F CB-1 TR200 Fat Cat CH150 Elite FES150 FES125, Pantheon (97 -) (98 -) (00 -) (94-00) (90 -) (83-93) (76-84) (83) (87-95) (69-76) (95-97) (80-96) (84-95) (78-84) (85-95) (85-95) (70-73) (76-84) (69-76) (84-95) (78-84) (70-73) (69-84) (70-73) (96-99) (ALL) (ALL) (87) (2007) (2007) (99-06) (00-06) (97-99) (91-99) (80-96) (97-03) (97-02) (01-06) (88-00) (84-87) (80-83) (82) (75-79) (93-99) (76-78) (90/94) (88-91) (ALL) (93-06) (87-03) (89-90) (86) (87) (ALL) (ALL) #3561 #3561 #3561 #3561 #3561 #4989 #4989 #3561 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #3591** #3591 #3591 #3591 #4989 #4989 #3561 #3591 #2528 #2528 #3591 #2528 #3591 #3560 #2528** #2528** #2528 #3560* #3560* #3560* #3560* #3560* #2519* #3560* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* PC680 PC680 PC680 PC680 PC680 PC925L PC925L PC680 PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC545MJ PC545MJ PC545MJ PC545MJ PC925L PC925L PC680 PC545MJ PC545 PC545 PC545MJ PC545 PC545MJ PC680MJ PC545 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 cc model (year) cat. # mfg sku # KAWASAKI 1500 1500 1300 1000 1000 900 900 750 750 650 636 600 600 KTM 640 620 400 400 MOTO GUZZ I 1100 1100 1100 1000 1000 850 850 750 650 650 650 500 POLARIS All SUZUKI 1400 900 750 750 750 650 600 600 600 600 400 TRIUMPH 600 YAMAHA 1600 1300 1300 1200 1100 1100 1100 920 600 600 VN 1500-A Vulcan VN 1500-C Vulcan KZ 1300 Touring KZ 1000-P Police Z1000 ZX900-C, Ninja ZX900-E, F Ninja KZ750-L, Ninja Zx750 Ninja ZX, 7RR KLX650C, R ZX636-B Ninja ZX-6R ZX600-G, J Ninja ZX ZX600-K Ninja ZX Adventure, Duke, RXC Adventure, Duke, LC4 LC4 E/XC RXC LC4 Cali/Spc/Jackl/Stone/EV Quota/Sport 1100 VII EV/Bassa California III,Quota,Millie Convert,Daytona, LeMans LeMans T3, T4, T5 Nevada,NTX,Strada,V7,V75 NTX V65 V65 Florida V50 Victory GV 1400GC RF900, R, S, ZS GSX750F Katana GSX-R750 GSXR750W DR650SE GSF600S Bandit GSX600F Katana GSX-R600 RF600R, S GSF400 Bandit Daytona 600 XV 1600 Road Star 1300 Royal Star XVZ Venture Royale XVZ12T Venture XJ1100 Maxim XS 1100, L, S XV 1100, S/ Virago XV 920/R/M Virago XJ600S Seca II XT600E (87-98) (96-97) (79-82) (82-05) (03-04) (98-99) (00-04) (93) (91-97) (93-96) (03-04) (98-02) (03) (99-02) (96-98) (96-98) (96-01) (94-05) (97-02) (98-99) (ALL) (86-88) (94-97) (98-03) (96-99) (94-95) (96-04) (96-03) (98-04) (97-03) (94-96) (91-93) (03-04) (99-03) (96-03) (86-92) (83-85) (82) (78-92) (86-99) (81-83) (92-98) (90-95) #3560 #3560 #3560 #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #4989 #2528 #4989 #4989 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #4989 #2519* #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2528*** #2528*** #3560 #3560 #3560 #3560 #3560 #3560 #2519* #2519* PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC925L PC545 PC925L PC925L PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC925L PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310

Incoming search terms:

2008 KAWASAKI KL650A8F: KLR 650 General And Tuning Engine Specifications

0

Filed Under (Kawasaki) by admin on 05-11-2010

download
Engine Type 4-stroke, Inline, 1-cylinder, DOHC, Liquid cooled Displacement 651 cc Bore x Stroke 100.0 x 83.0 mm Compression Ratio 9.8:1 Maximum Torque 36.9 lb-ft at 5,500 rpm Carburetor Keihin CVK40, Constant velocity, Diaphragm-type Ignition System Magneto CDI (Rotor) Ignition Advance Electronic Crankshaft Rotation Clockwise from ignition (RH) side Cylinder Material Aluminum alloy with ferrous sleeves Fuel Min 91 Research/87 Avg. Oct. Unleaded OK Coolant 50% distilled water/50% ethylene glycol base antifreeze —Capacity 1.05 L (1.1 qt.) —Level Level with radiator filler neck. Transmission Clutch Type Wet, Multi-disc, Manual Transmission 5-speed, Constant mesh, Return shift Shift Pattern(Bottom up) 1-N-2-3-4-5 Gear Ratios —1st 2.27 (34/15) —2nd 1.44 (26/18) —3rd 1.14 (25/22) —4th 0.95 (21/22) —5th 0.79 (19/24) Primary Ratio 2.28 (75/33) Final Ratio 2.87 (43/15) Overall Ratio (Top Gear) 5.157 Chassis Wheelbase 1,480 mm (58.3 in.) Seat Height 890 mm (35.0 in.) Ground Clearance 210 mm (8.3 in.) Dry Weight 175 kg (386 lb.) Fuel Tank Capacity 22.1 L (5.8 gal.) Tire Size —Front 90/90-21 54S —Rear 130/80-17 65S Brake Type —Front Single Hydraulic Disc —Rear Single Hydraulic Disc Brake Size —Front 254 mm Effective Diameter —Rear 212 mm Effective Diameter Wheel Travel —Front 206 mm (7.9 in.) —Rear 185 mm (7.3 in.) Model Identification Year & Model ’08 KL650A8F:KLR 650 Color 1. Blue 21 (S8) 2. KMT. Candy Lime Green (175) 3. Sunbeam Red (H1) VIN Range JKAKLEE1 * 8DA00101 — Engine No. Range KL650AE007501— Engine No. Location RH top crankcase, below carburetor Tuning Specifications Engine Valve Clearance (Cold) Intake: 0.10-0.20 mm Exhaust: 0.15-0.25mm —Adjustment Method Shim on tappet Spark Plug NGK DPR8EA-9 or ND X24EPR-U9 —Gap 0.8-0.9 mm Ignition Timing 10.0° BTDC (“F” mark) at 1300 rpm 30.0° BTDC (In double marks) at 3300 rpm Pilot Screw Sealed—not adjustable Idle Speed 1300 ±100 rpm Engine Oil API SE, SF, or SG, API SH or SJ of JASO MA Class, 10w40 —w/Filter Change 2.5 L —No Filter Change 1.7 L —Level On center stand, wait 5 min, middle of window —Pressure (Hot) 2.0-2.5 kg/cm2 at 4,000 rpm, 90° C Chassis Fork Oil SAE 10W20 —Capacity 581 – 589 cc dry —Level 170 ±2 mm (fork compressed, spring removed) Fork Air Pressure (Cold) 0.0 kg/cm2 , max 2.5 kg/cm2 Tire Pressure (Cold) —Front 22 psi, change for course and rider preference —Rear 22 psi, change for course and rider preference Drive Chain Slack 35-45 mm (on center stand, tightest point, STD)

KAWASAKI Brute Force 750i, 650 4x4i BACK BUMPER MOUNTING INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
KAWASAKI Brute Force 750i, 650 4x4i Ref. Item Description Item # Qty 1 Back Bumper 166-236 1 2 Attachment A32 2 3 Bolts 2″ x 5/16″ (Hex) ZZZ-H0425 2 4 Bolts 1 1/2″ x 5/16″ (Hex) ZZZ-H0424 2 5 Bolt ¾” x 5/16″ (Hex) ZZZ-H0423 2 6 Flat Washer 5/16″ 146-016 6 7 Lock Nut 5/16″ 0404-90239 6

Incoming search terms: