2002 kawasaki prairie 650 specifications

You search Auto repair manual PDF 2002 kawasaki prairie 650 specifications, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2002 kawasaki prairie 650 specifications Direct Download speed 5282 Kb/s

  2002 kawasaki prairie 650 specifications Full Version speed 6162 Kb/s



Kawasaki Prairie 360,650,700 ATV PLOW Plow Mounting Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Mount Installation Note: There are different hole locations on the plow mount depending on the bike model. For Prairie 360 use the middle hole locations (B), for Prairie 650 and Twin Peaks 700 use hole locations (A) on mounting plate, as shown in Figure 1. Figure 1 Hole Locations WARN INDUSTRIES PAGE 3 67954 Rev A3 To install the plow mount to the underside of the vehicle install the front two U-bolts PN 60869, and loosely tighten the 5/16″ nuts. Pull the plow mount back in the furthest position and then fully tighten, as shown in Figure 2. For the Kawasaki Prairie 360 use the second set of U-bolts PN 61262 and securely tighten around the frame in hole location (B) . For Kawasaki Prairie 650 and Suzuki Twin Peaks 700 drill a 3/8″ hole through the aluminum skid plate, using the plow mount as a template, as shown in Figure 3. Repeat the same process on the other side. After both holes are drilled attach the mounting plate with the second set of U-bolts PN 61262 and securely tighten around the frame in hole location (A) . Tighten all fasteners securely. Torque 5/16″ Bolts: 20ft. lb.

Incoming search terms:

Kawasaki 650/360 Prairie Lift Kit Installation and removal Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Place jack under center of ATV front end and lift until front wheels clear the ground. Be careful to support ATV properly so that it is securely supported but so that A-arms and shocks can droop to full extension. 2) Remove front wheels. 3) Remove or loosen front plastic. 4) Remove C-clip and nut at the top of the strut. 5) Screw bracket “A” on top of strut to the same torque specifications as the nut. 6) Place the top adapter “A” through the top of the strut mount, and screw the original nut on the top of bracket “A” securing it to the strut mount. Tighten this nut to the required manufacturer specifications and replace the factory C-clip. 7) Repeat the procedure for the other side. 8) Install the wheels, torque wheel lug nuts to manufacturer’s specifications, lower and remove jack. Check for clearance problems or misalignment. Rear Lift 1) Place jack under ATV at the rear of the bottom skid plate and lift until the weight is off of the suspension. Be careful to secure the ATV properly so as not to fall off the jack. 2) Remove the bottom of the shock from the shock mount on the axle. 3) After removing the shock, jack the ATV up 1″-2″ further. 4) Place Bracket “B” between the shock and shock mount with the notched out ends facing downward. Insert stock bolt to secure bracket “B” to the shock mount and the shock. Fasten nut. 5) Insert the new 12x75mm Bolt to the top of bracket “B” and the shock eyelet and secure with a new 12mm nut. 6) Tighten all nuts and bolts to manufacturer’s torque specifications. 7) Install the wheels, torque wheel lug nuts to manufacturer’s specifications, lower and remove jack. Check for clearance problems or misalignment.

Incoming search terms:

2008 KAWASAKI KL650A8F: KLR 650 General And Tuning Engine Specifications

0

Filed Under (Kawasaki) by admin on 05-11-2010

download
Engine Type 4-stroke, Inline, 1-cylinder, DOHC, Liquid cooled Displacement 651 cc Bore x Stroke 100.0 x 83.0 mm Compression Ratio 9.8:1 Maximum Torque 36.9 lb-ft at 5,500 rpm Carburetor Keihin CVK40, Constant velocity, Diaphragm-type Ignition System Magneto CDI (Rotor) Ignition Advance Electronic Crankshaft Rotation Clockwise from ignition (RH) side Cylinder Material Aluminum alloy with ferrous sleeves Fuel Min 91 Research/87 Avg. Oct. Unleaded OK Coolant 50% distilled water/50% ethylene glycol base antifreeze —Capacity 1.05 L (1.1 qt.) —Level Level with radiator filler neck. Transmission Clutch Type Wet, Multi-disc, Manual Transmission 5-speed, Constant mesh, Return shift Shift Pattern(Bottom up) 1-N-2-3-4-5 Gear Ratios —1st 2.27 (34/15) —2nd 1.44 (26/18) —3rd 1.14 (25/22) —4th 0.95 (21/22) —5th 0.79 (19/24) Primary Ratio 2.28 (75/33) Final Ratio 2.87 (43/15) Overall Ratio (Top Gear) 5.157 Chassis Wheelbase 1,480 mm (58.3 in.) Seat Height 890 mm (35.0 in.) Ground Clearance 210 mm (8.3 in.) Dry Weight 175 kg (386 lb.) Fuel Tank Capacity 22.1 L (5.8 gal.) Tire Size —Front 90/90-21 54S —Rear 130/80-17 65S Brake Type —Front Single Hydraulic Disc —Rear Single Hydraulic Disc Brake Size —Front 254 mm Effective Diameter —Rear 212 mm Effective Diameter Wheel Travel —Front 206 mm (7.9 in.) —Rear 185 mm (7.3 in.) Model Identification Year & Model ’08 KL650A8F:KLR 650 Color 1. Blue 21 (S8) 2. KMT. Candy Lime Green (175) 3. Sunbeam Red (H1) VIN Range JKAKLEE1 * 8DA00101 — Engine No. Range KL650AE007501— Engine No. Location RH top crankcase, below carburetor Tuning Specifications Engine Valve Clearance (Cold) Intake: 0.10-0.20 mm Exhaust: 0.15-0.25mm —Adjustment Method Shim on tappet Spark Plug NGK DPR8EA-9 or ND X24EPR-U9 —Gap 0.8-0.9 mm Ignition Timing 10.0° BTDC (“F” mark) at 1300 rpm 30.0° BTDC (In double marks) at 3300 rpm Pilot Screw Sealed—not adjustable Idle Speed 1300 ±100 rpm Engine Oil API SE, SF, or SG, API SH or SJ of JASO MA Class, 10w40 —w/Filter Change 2.5 L —No Filter Change 1.7 L —Level On center stand, wait 5 min, middle of window —Pressure (Hot) 2.0-2.5 kg/cm2 at 4,000 rpm, 90° C Chassis Fork Oil SAE 10W20 —Capacity 581 – 589 cc dry —Level 170 ±2 mm (fork compressed, spring removed) Fork Air Pressure (Cold) 0.0 kg/cm2 , max 2.5 kg/cm2 Tire Pressure (Cold) —Front 22 psi, change for course and rider preference —Rear 22 psi, change for course and rider preference Drive Chain Slack 35-45 mm (on center stand, tightest point, STD)

Incoming search terms:

Kawasaki Prairie 650 Snorkel REMOVAL AND INSTALLATION

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Remove plastic from around air filter housing. Remove air filter housing lid and air filter. Remove 8 small screws from bottom of air box. Next, remove bolt from front and rear of air box. Remove the air box. Remove old snorkel from air box. Remove hose clamp and rubber drain tube from old snorkel. Reinstall on new snorkel. Install new snorkel vertical with the air box. Reinstall air box making certain all vacuum hoses are reinstalled. Check for clearance around new snorkel. Make sure all wires and steering stem do not come into contact with the snorkel. Adjust as necessary Reinstall filter and filter cover. Jetting depends on your elevation. A good starting point for 1000 feet and under is to remove the main jet #142 from the rear carburetor. Install it in the front carburetor. Purchase and install a #145 main jet in the rear carburetor. This works well with an aftermarket air filter and exhaust. For a very reasonable price, HMF Exhaust offers a jet kit with their exhaust that we recommend. Let them know Diamond G Racing sent you.

Single-Cylinder BMW G 650 X Model Series

0

Filed Under (BMW) by admin on 16-11-2010

download
introducing the new range of single-cylinder models, BMW Motorrad is broadening its model line-up with a clear focus on additional target groups. Proceeding from the same technical foundation, the Company has created three new motorcycles absolutely different in their features and characteristics: the G 650 Xchallenge Hard Enduro, G 650 Xmoto Street Moto, and the G 650 Xcountry Scrambler. With their outstanding product substance, their purist looks, and their exceptionally sporting riding characteristics, these single-cylinder models are filling attractive niches in the market. And through their low unladen weight of less than 160 kg or 353 lb according to the DIN standard, they offer dynamic performance for both the connoisseur and the sports-minded rider. Market launch of the new G 650 X model series is planned in good time for the beginning of the season in spring 2007. These new machines with the smallest engines in the BMW model range offer particularly the young and young-at-heart motorcycle rider exactly the right entry into the world of BMW motorcycles, but are not entry-level bikes in the conventional sense of the word: On the contrary, the G 650 Xchallenge Hard Enduro will thrill the customer who wishes to really benefit from the enormous offroad potential of his machine. The G 650 Xmoto Street Moto, in turn, with its very impressive active riding qualities, offers the genuine enthusiast a new dimension in riding pleasure. The G 650 Xcountry Scrambler, finally, stands for carefree riding pleasure and nimble performance both on the road and off the beaten track. Indeed, this unique machine is able to meet all kinds of requirements and offer virtually all riding qualities ranging from city use via country roads and small, winding lanes, all the way to offroad tracks presenting the most challenging requirements. The G 650 Xcountry therefore conveys the classic but relaxed feeling of riding a genuine Scrambler as well as the concept of “wandering” on your motorcycle into today’s world in a most modern style. And last but certainly not least, riding pleasure is guaranteed under all conditions and in every situation, since the G 650 Xcountry offers the same outstanding engine and running gear qualities as its two very sporting “sister models

Incoming search terms:

KAWASAKI Jet Ski STX-12F SPECIFICATIONS

0

Filed Under (Kawasaki) by admin on 05-11-2010

download
FEATURES & BENEFITS Kawasaki 2007 SPECIFICATIONS: JT1200D7F Engine type……………… 4-stroke, water cooled, 4- cylinder Displacement…………… 1,199 cm3 Bore & stroke…………… 83.0 x 55.4 mm Compression ratio…… 11.2:1 Induction system……… DOHC 16 valve (4 valves per cylinder) Maximum power………. 92 kW (125 PS) / 7,200 r/min Maximum torque……… 125 N·m / 6,500 r/min Cooling system……….. inducted water Fuel system…………….. EFI with single 54 mm throttle Starting ……………………. electric Battery…………………….. sealed, 12V 18Ah Propulsion system…… axial flow, single stage jet pump Maximum thrust………. 3,675 N (375 kgf) Seating capacity………. 3 seater Fuel capacity…………… 62 L L x W x H…………………. 3,120 x 1,180 x 1,050 mm Dry weight……………….. 334 kg Colours……………………. Red NOTE: Specifications subject to change without notice ENGINE Ñ Chrome composite plated cylinders are lightweight, durable and quickly carry heat away from the combustion chamber and piston for supreme durability at high power output. Ñ Semi-dry sump uses a single feed oil pump. Ñ Tip over protection shuts the engine off if the craft tilts more than 61o. Ñ 4-valves per cylinder provides maximum valve area for optimum flow. Fuel system Ñ Electronic Fuel Injection (EFI) with a single Mitsubishi throttle body and an injector at each intake port. Ñ Long intake tract enhances low-end power. Ñ Large capacity, low-noise airbox. Ñ Finger-type throttle reduces hand fatigue. Water-jacketed semi-dry exhaust Ñ Double-walled exhaust manifold and dual waterboxes help reduce noise. Ñ Water surrounding the exhaust system lowers engine compartment temperatures for more power. Ñ Semi-dry exhaust system keeps cooling water out of the exhaust before the waterbox to prevent water from entering the engine if the boat should capsize. Ñ Emissions meet US EPA 2006 and CARB 2008 regulations. Lanyard engine stop switch Ñ Engine will not crank with lanyard removed. Ñ Fastened to the rider, lanyard cuts the ignition if the rider dismounts. DRIVE SYSTEM Three-blade oval edge stainless steel impeller Ñ The shape of the blades give maximum efficiency with minimum cavitation. Ñ Fully enclosed impeller for damage protection. Ñ Stainless steel pump insert increases durability and helps ensure reliable performance. Ñ Tough stainless steel is used for incredible durability. HULL Ñ One-piece chopper over foam (COF) hull construction is lighter than a conventional hand-laid hull of similar size. Ñ Cab forward design makes more space for the rider and passengers. Ñ Gel coat for deep, lustrous, scratch resistant finish. Ñ Open rear deck for carrying bulky items, putting on skis, etc. Ñ
An automatically retractable boarding step makes boarding from deep water easy. Kawasaki Smart Steering (KSS) Ñ A steering sensor is linked to the EMM to aid in boat handling when the throttle is quickly released from high speed. Detail features Ñ 62 litre fuel tank for increased range. Ñ LCD instrumentation includes digital speedometer, tachometer, hour meter, clock, trip distance, trip time, fuel level and warning lamps. Ñ Includes high tech. troubleshooting function for the fuel injection system. A computer hook-up allows easy retrieval of entire troubleshooting history. Ñ A remote cooling system flushing point is included. Ñ Front hatch made of ABS for reduced weight, increased durability and enhanced appearance. Ñ Mirrors mounted on the deck reduce weight and enhance appearanced

Incoming search terms:

1992 Kawasaki ZZR 1100 technical specifications

0

Filed Under (Kawasaki) by admin on 04-11-2010

download
Kawasaki ZZR 1100 1992: technical specifications Rating: 8.1 Performance: 7.7 Reliability: 9.3 Appearances: 8.3 Price/Quality: 7 # votes: 3 GENERAL Model Kawasaki ZZR 1100 1992 Category Sport
ENGINE Type 1052 cc, water cooled, 4 – cylinders in line, 4-stroke
Bore x stroke (mm) 76 mm x 58 mm Valves 4 valves per cylinder Power
146 hp (108.9 kW) @ 10500 rpm Torque 110 Nm (81.1 ft. lbs) @ 8500 rpm TRANSMISSION Gearbox 6 speed Final drive Chain WHEELS Front
The above specifications are subject to change without notice. Trademarks and logos of third parties used in the Site are exclusive property of the respective own

Incoming search terms:

Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Upgrading the Suspension on the Kawasaki ER6-F/ N

0

Filed Under (Kawasaki) by admin on 30-11-2010

download
Top fork is as removed. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Before removing the fork from the clamps on the yokes I loosened the fork top. Before removing the fork top the fork-slider was placed in a vice and the bottom bolt loosened….. … before finally being removed with the fork upside down. Because the springs were still in situ this gave sufficient tension on the damper-rod to prevent it from turning and allow the bolt to be removed. When I turned the fork the right-way up to remove the fork-top I did it over a container to catch the oil. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource All the OE components that will no longer be required. Left to right. Fork-top, spacer tube, washer, spring, damper-rod. Bottom bolts get re-used. Old and new, laid-out for comparison. The damper unit, minus spring and fork-top, drops inside the stanchion and slider. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Then the bolt goes back in, as tight as possible, to secure it. Top fork is done, second one awaits. Note the spring seat on the right, just below the spring. This drops over the damping rod after the oil has been added. The small locking-nut screws over the threaded part of the damping-rod next, all the way to the bottom. Spring drops in and then the fork-top screws on to the damping-rod as well, all the way down to the lock-nut which is used to secure it. At this point the stanchion is extended to the fork-top which is screwed in. Job done.

Incoming search terms:

ODYSSEY DRYCELL MOTORCYCLE BATTERY COMPATIBILITY

0

Filed Under (Triumph) by admin on 30-10-2010

download
BMW 1200 1200 1150 1100 1100 1000 1000 1000 1000 900 850 800 800 800 750 750 750 750 750 650 650 600 600 500 BUELL 1200 1200 1200 1000 DUCATI 860 750 500 HARLEY DAVIDSON 1570 1570 1450 1450 1340 1340 1340 1200 883 HONDA 1800 1500 1200 1100 1000 1000 900 750 750 650 650 650 600 400 200 150 150 125 K1200RS, LT R1200C R1150GS, R R1100GS/R R1100RS/T/S/LT “K” Models R100/7 100RS R100GS, R, RS, RT R90/6, R90S R850R R80GS, R80ST R80, R80RT R80/7/RT K75, RT K75C, S R75/5 R75/7 R75/6 R65 R65LS R60/5 R60/6, R60/7 R50/5 S1 Lightning X1, S3, S3T, M2 S2/T, RS1200, RR1200 RR1000 GT, GTS GT, Laguna Seca GTL, GTV, Sport FXST, FLST FXD FXD FXST, FLST FXD FXST, FLST FL/H/T/HT XL, XLH XLH, XLH GL1800, VTX1800C Gold Wing-All Gold Wing-All Gold Wing-GL1100 CBX1000, SS opt. Gold Wing-GL1000 CBR900R,RR CB750A (Hondamatic) VFR740R/ RVF750R NT650, SLR650, NX650 Vigor 650 XR650L VT600C, CD, CBR600 CBR400F CB-1 TR200 Fat Cat CH150 Elite FES150 FES125, Pantheon (97 -) (98 -) (00 -) (94-00) (90 -) (83-93) (76-84) (83) (87-95) (69-76) (95-97) (80-96) (84-95) (78-84) (85-95) (85-95) (70-73) (76-84) (69-76) (84-95) (78-84) (70-73) (69-84) (70-73) (96-99) (ALL) (ALL) (87) (2007) (2007) (99-06) (00-06) (97-99) (91-99) (80-96) (97-03) (97-02) (01-06) (88-00) (84-87) (80-83) (82) (75-79) (93-99) (76-78) (90/94) (88-91) (ALL) (93-06) (87-03) (89-90) (86) (87) (ALL) (ALL) #3561 #3561 #3561 #3561 #3561 #4989 #4989 #3561 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #3591** #3591 #3591 #3591 #4989 #4989 #3561 #3591 #2528 #2528 #3591 #2528 #3591 #3560 #2528** #2528** #2528 #3560* #3560* #3560* #3560* #3560* #2519* #3560* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* PC680 PC680 PC680 PC680 PC680 PC925L PC925L PC680 PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC545MJ PC545MJ PC545MJ PC545MJ PC925L PC925L PC680 PC545MJ PC545 PC545 PC545MJ PC545 PC545MJ PC680MJ PC545 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 cc model (year) cat. # mfg sku # KAWASAKI 1500 1500 1300 1000 1000 900 900 750 750 650 636 600 600 KTM 640 620 400 400 MOTO GUZZ I 1100 1100 1100 1000 1000 850 850 750 650 650 650 500 POLARIS All SUZUKI 1400 900 750 750 750 650 600 600 600 600 400 TRIUMPH 600 YAMAHA 1600 1300 1300 1200 1100 1100 1100 920 600 600 VN 1500-A Vulcan VN 1500-C Vulcan KZ 1300 Touring KZ 1000-P Police Z1000 ZX900-C, Ninja ZX900-E, F Ninja KZ750-L, Ninja Zx750 Ninja ZX, 7RR KLX650C, R ZX636-B Ninja ZX-6R ZX600-G, J Ninja ZX ZX600-K Ninja ZX Adventure, Duke, RXC Adventure, Duke, LC4 LC4 E/XC RXC LC4 Cali/Spc/Jackl/Stone/EV Quota/Sport 1100 VII EV/Bassa California III,Quota,Millie Convert,Daytona, LeMans LeMans T3, T4, T5 Nevada,NTX,Strada,V7,V75 NTX V65 V65 Florida V50 Victory GV 1400GC RF900, R, S, ZS GSX750F Katana GSX-R750 GSXR750W DR650SE GSF600S Bandit GSX600F Katana GSX-R600 RF600R, S GSF400 Bandit Daytona 600 XV 1600 Road Star 1300 Royal Star XVZ Venture Royale XVZ12T Venture XJ1100 Maxim XS 1100, L, S XV 1100, S/ Virago XV 920/R/M Virago XJ600S Seca II XT600E (87-98) (96-97) (79-82) (82-05) (03-04) (98-99) (00-04) (93) (91-97) (93-96) (03-04) (98-02) (03) (99-02) (96-98) (96-98) (96-01) (94-05) (97-02) (98-99) (ALL) (86-88) (94-97) (98-03) (96-99) (94-95) (96-04) (96-03) (98-04) (97-03) (94-96) (91-93) (03-04) (99-03) (96-03) (86-92) (83-85) (82) (78-92) (86-99) (81-83) (92-98) (90-95) #3560 #3560 #3560 #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #4989 #2528 #4989 #4989 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #4989 #2519* #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2528*** #2528*** #3560 #3560 #3560 #3560 #3560 #3560 #2519* #2519* PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC925L PC545 PC925L PC925L PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC925L PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310

Incoming search terms:

KAWASAKI Brute Force 750i, 650 4x4i BACK BUMPER MOUNTING INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
KAWASAKI Brute Force 750i, 650 4x4i Ref. Item Description Item # Qty 1 Back Bumper 166-236 1 2 Attachment A32 2 3 Bolts 2″ x 5/16″ (Hex) ZZZ-H0425 2 4 Bolts 1 1/2″ x 5/16″ (Hex) ZZZ-H0424 2 5 Bolt ¾” x 5/16″ (Hex) ZZZ-H0423 2 6 Flat Washer 5/16″ 146-016 6 7 Lock Nut 5/16″ 0404-90239 6

Incoming search terms:

Incoming search terms: