2002 ktm lc4 plastics

You search Auto repair manual PDF 2002 ktm lc4 plastics, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2002 ktm lc4 plastics Direct Download speed 5282 Kb/s

  2002 ktm lc4 plastics Full Version speed 6162 Kb/s



Ktm 625/ 640/ 660 LC4's and some 640 Adventures Removal and Installation Manual

0

Filed Under (KTM) by admin on 24-01-2012

download
1. There are 3 pages of instructions here. Review all 3 first! These model bikes normally require modifications. 2. Warning: Once the triple clamp is loose, the forks can roll away from the bike . Follow step 2 carefully. 3. Block the front and rear tire securely before removing the top triple clamp, keeping the weight pushed on the front wheel so the front tire cannot move forward and the forks are forced upward, keeping the bearing in the head tube. 4. Remove the 4 bolts holding your bars tight and lay the bars forward out of the way. 5. Using Loc-tite, change the lower nuts on the under side of your triple clamp that hold your bar perches. Use the “low profile” version that we have supplied in the kit. You will need access to the Allen head bolts in the lower perch halves. Without these low profile nuts the triple clamp will not be free to turn lock to lock. There are occasions where you may have to grind on the frame bracket to allow a little extra clearance for even the low profile nuts (see photo). Because the bars are rubber mounted, this clearance varies from bike to bike. Turn the triple clamp lock to lock and be sure you have clearance. You must change them now, as later you won’t have room to do so. 6. Now remove the top triple clamp taking note of how tight the main nut is, so you can re-tighten to the exact amount. 7. Remove the tin bearing shroud (cover) and rubber seal. The lips of the seal face downward for correct installation. 8. The new shorter bearing shroud will replace the stock tin shroud, giving the frame bracket more room to seat. 9. Grease your bearings while you have them exposed. (Keep the grease off the area where our frame bracket mounts). 10. Only if your model is equipped with one, you will need to cut off the upper portion of the square steering lock receiver box (see photo). The steering lock stays functional as the lock-pin still engages the lower the portion of the box. Mark and cut the top of the box off. You must cut enough to allow our frame bracket to drop down far enough so the entire bracket grabs the head tube. If you don’t allow the frame bracket enough clamping surface it will come loose. The upper edge of the frame bracket should be level with the step where your stock bearing seal seats. (See photo). 11. Install the frame bracket so it matches the clamping area on your head tube, but do not tighten it yet. Do not remove the paint on the frame where the frame bracket fits. The paint is calculated as part of the correct dimension. On most LC4′s you will need to grind the weld at the back of the head tube, so the bracket can drop all the way down flush. Each bike is a little different; some require a lot of grinding and some very little. Try to remove the weld while retaining the original diameter of the head tube where our bracket will clamp. It is essential for the frame bracket to clamp to a symmetrical, round head tube. When you’ve removed the majority of weld the finished removal should be done with a file for precision clearance, without touching the area where the clamp will seat

Incoming search terms:

KTM KINETO TRACKING MOUNT – MODEL K433 Installation and Removal Manual

0

Filed Under (KTM) by admin on 30-01-2012

download
the KTM meets the needs of a wide variety of test range and scientific applications:  On-board operator, or remote analog or digital control  Payloads up to 1200 pounds (unmanned) or 600 pounds (manned)  Mission configuration with four (manned) or six (unmanned) payload positions  Complete turnkey systems available  Detailed installation documentation FIELD-PROVEN RUGGED AND RELIABLE The KTM consistently demonstrates its performance and durability:  Weather tight seals designed to withstand harsh range environments  The KTM’s direct drive axis design delivers smooth, jitterfree tracking to ensure precise Time, Space and Position Information (TSPI)  Self-contained and trailer-mounted, the KTM is quickly and easily deployed via highway and unimproved roads to remote tracking sites  Digital Control System (DCS) that guarentees system reliability WHEN THE RANGES REQUIRED PRECISE AND RELIABLE OPTICAL TRACKING MOUNTS, THEY SELECTED THE BRASHEAR KINETO TRACKING MOUNT MORE THAN 150 TIMES. Recognized Standard for Tracking Systems Worldwide THE KTM DIGITAL CONTROL SYSTEM (DCS) INCLUDES:  High speed communication via an Ethernet interface to provide remote operation  Advanced servo loop control to optimize tracking performance  Built-in error correction to ensure precision tracking accuracy  Versatile chassis architecture that accommodates additional PC104 cards suchas an “Automatic Video Tracker” (AVT) to satisfy specific customer requirements and missions

Incoming search terms:

KTM 4357/ 4860 MX Multi Adjuster WP Suspension manual Disassembly And Assembling

0

Filed Under (KTM) by admin on 13-02-2011

download
Disassembly forkleg 12_062 12_079Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 5 Frontfork 4357/4860 MXMA 02/2002 Clamp the forkleg (axle-clamp) in the vice and let the outer-tube down. Pull the spring downwards… …and place open-end spanner (size 22) on the hydraulic stop. Unscrew the screw-cap. 12_067 12_068 12_069 12_072Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 6 Frontfork 4357/4860 MXMA 02/2002 Remove the screw-cap from the piston- rod. 12_070 Remove the preload spacers. 12_074 Pull the spring downwards and remove the spanner. 12_075Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 7 Frontfork 4357/4860 MXMA 02/2002 Remove the spring. 12_076 Remove the adjustment tube with the O-ring. 12_089
Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 8 Frontfork 4357/4860 MXMA 02/2002 Clamp the axle-clamp in the vice so that the forkleg is at an angle of ±45 degrees. 12_095 Unscrew the compression holder out of the axle-clamp. (size 19) (when the cartridge is rotating with the holder, bend the piston- rod a little bit to the side) 12_096 Drain the oil out the forkleg. 12_094 Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 9 Frontfork 4357/4860 MXMA 02/2002 Remove holder compression. Caution: oil iscoming out the cartridge. Disassemble the cartridge out the forkleg. 12_097 12_098 12_099 Disassemble the dust-wiper

Incoming search terms:

KTM Preload Adjuster frontfork Disassembly And assembling

0

Filed Under (KTM) by admin on 13-02-2011

download
Product Exploded View Disassembly & Assembling Workshop manual Preload Adjuster frontfork 5 Preload Adjuster Frontfork 03/2002 Screw the screw-cap to the right so that the spring washer is turning out of the screw-cap PA. Remove the spring washer. Pay attention to the assembling direction!!! Turn the plastic adjustment tube holder out of the screw-cap. 12_021 12_022 12_023Product Exploded View Disassembly & Assembling Workshop manual Preload Adjuster frontfork 6 Preload Adjuster Frontfork 03/2002 1. Remove the O-ring inside. Unscrew the air release plug. 12_024 12_025 12_026 2. Remove the O-ring.Product Exploded View Disassembly & Assembling Workshop manual Preload Adjuster frontfork 7 Preload Adjuster Frontfork 03/2002 Disassemble the adjusting knob from the screw-cap. Pay attention to the steel balls and spring!!! 12_027 12_028 12_029 Heat the steel nut. Unscrew the nut (size 32) clockwise .Product Exploded View Disassembly & Assembling Workshop manual Preload Adjuster frontfork 8 Preload Adjuster Frontfork 03/2002 The nut. Pay attention to the assembling direction!!! Remove the O-ring. 12_030 12_031 12_032 Push the holder rebound PA out of the screw-cap.Product Exploded View Disassembly & Assembling Workshop manual Preload Adjuster frontfork 9 Preload Adjuster Frontfork 03/2002 – springring – spring washer – O-rings – holder rebound adjustment tube – rebound adjusting knob with steel balls and spring – air release screw with O-ring – nut – holder rebound adjustment cpl. with O-ring – screw-cap PA

Incoming search terms:

2001-2002 GL1800 A ABS Speed Sensor Wire Clamp Location INSPECTION/ REPAIR PROCEDURES

0

Filed Under (Honda) by admin on 29-01-2011

download
1. If the VIN is within the preceeding range, inspect the front ABS speed sensor wire clamp according to the following illustrations. 2001-2002 GL1800A ABS Speed Sensor Wire Clamp Location INCORRECT Installation CORRECT Installation Service Bulletin American Honda Motor Co., Inc. 2001-2002 GL1800 ABS Speed Sensor Wire Clamp Location 0112 GL1800 #9*GL1800 #9*0112*2001-2002 GL1800 ABS Speed Sensor Wire Clamp Location*GL1800, ABS Speed Sensor Wire Clamp Location*Motorcycle*1800 2 of 2 ©2001 American Honda Motor Co., Inc. – All Rights Reserved GL1800 #9 DECEMBER 2001 IDENTIFICATION There is no identification mark associated with this Service Bulletin. PARTS INFORMATION There is no parts information associated with this Service Bulletin. WARRANTY INFORMATION The normal warranty claim submission requirements apply. Submit one warranty claim per VIN with the following information only: Inspected and REPAIRED Template: GL#9 Hours: 0.2 hours Parts: None If the clamp is installed correctly on top of the speed sensor, no further action is necessary. 3. If the clamp is installed incorrectly under the speed sensor, remove and reinstall the clamp and speed sensor correctly. Torque the bolts,. Torque: 12 N • m (1.2 kgf • m, 9 lbf • ft) If the speed sensor wire clamp for the front ABS speed sensor is installed incorrectly, the ABS speed sensor air gap may be out of specification. This does not affect ABS speed sensor operation, but the clamp should be installed correctly. Inspect and repair all affected units using the Inspection/Repair procedures listed below. Inspect all unsold units and customer units brought in for service. AFFECTED UNITS 2001-2002 GL1800A units as follows: MODEL 2001 GL1800A All units 2002 GL1800A 1HFSC474*2A100001 – 1HFSC474*2A101643 * = denotes check digit Any unit in the above VIN range may be affected and should be inspected according to the procedures in this Service Bulletin. All units outside of the above VIN range do not require inspection. CUSTOMER NOTIFICATION There is no customer notification associated with this Service Bulletin.

Incoming search terms:

KTM EXC Enduro & SX Motocross REPAIR MANUAL

0

Filed Under (KTM) by admin on 06-03-2012

download
Thanks to a history of competition successes, particularly in off-road racing, KTM motorcycles enjoy a large and loyal following. Established in 1953, KTM (from Kraftfahrzeuge Trunkenpolz Mattighofen where founder, Hans Trunkenpolz, had his engineering works) went through difficult times in the early 1990s. After a takeover, the Austrian company emerged as KTM Sportmotorcycle AG and has gone from strength to strength in recent years. Mainstay of their range are their Enduro and Motocross models, the EXC and SX, and these are covered in the latest new manual from Haynes. Models covered are the 250, 400, 450, 520 and 525 EXC and SX with 4-stroke sohc engines, 2000 to 2007. Information has also been included on the SMR Supermoto versions and MXC/XC derivatives. Haynes Manuals for cars and motorcycles are so popular that 150 million have been sold worldwide. Lay them end-to-end and they would circle the globe at the equator! The new manual begins with essential pre-ride checks, competition prep and routine maintenance tasks before moving on to more major repairs. There are comprehensive, fully illustrated, instructions for overhauling the engine, transmission, brakes, suspension and electrical system. Useful reference pages include colour wiring diagrams, fault-finding charts and a comprehensive section on tools and workshop tips. Because all Haynes Manuals are based on a complete stripdown and rebuild, not only are the procedures written from first-hand experience, but there is information about special tools required for each job, and its complexity, plus Haynes tips for saving time and money. The new Haynes KTM EXC Enduro & SX Motocross Manual is the only complete manual for owners of these motorcycles.

Incoming search terms:

KTM ATV 525 XC specification

0

Filed Under (KTM) by admin on 12-11-2010

download
Engine ] Pure power for Enduro enthusiasts. The power of the 525 XC is the indisputable benchmark in the ATV Enduro sector. Its acceleration and top speed cast a shadow over all its predecessors. Variable ignition curves and perfect maintenance features like simple valve play adjustment and the removable clutch cover are even further highlights of the XC engine that make the KTM Enduro quads so superior. First Oil Filling for all KTM Engines. [ CarburEttor ] The Keihin carburettor, which has been proven multiple times in racing, with 39 mm and the Throttle Positioning System guarantees a uniform, forceful power delivery in all speed ranges. It ensures an unrivalled response behavior and perfect service-friendliness at all times. [ StartEr ] Packed in a space-saving manner into the free space behind the cylinder head, the small, light electric starter motor is ready for use. It brings every KTM ATV up to speed reliably and comfortably even when racing becomes hectic. [ rEar SuSPENSIoN ] Premium-quality ÖHLINS suspension components specially designed for tough Enduro use are provided as standard – both at the front and the rear. Easy to adjust, they guarantee optimal tuning for the most varied of terrains. Another highlight: the front and rear spring travel of 275 mm and 272 mm respectively is 100 % trend-setting for an Enduro ATV! [ alumINIum SubFramE ] The rear subframe is made of aluminium and is extremely light and easy to remove. [ FramE ] The lightweight, extremely durable frame sets the benchmark in the quad racing segment and is made of high-strength, powder-coated Chromoly steel. [ haNDlEbar ] An ultra-durable tapered aluminium Magura® handlebar comes standard that is four-position adjustable to suit your preferred ergonomics. Further highlights are the functional and individually adjustable operating levers for brake and hydraulic clutch. In addition, the chassis has an integrated mount for a steering damper – available as a PowerPart accessory. [ CurvED raDIator ] Best cooling by means of its curved shape and the resulting maximized surface area. [ rImS / tIrES ] MAXXIS Razr tyres on light, stable DWT aluminium rims. [ ExhauSt ] The powerful XC silencer is made of light-weight aluminium.

Incoming search terms:

2005-2007 KTM MOTORCYCLE REPAIR MANUAL

0

Filed Under (KTM) by admin on 21-11-2010

download
Adjustments -Take notice of the position of the compression adjustment 1 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -Remove the rubber cap out of the axleclamp. -Take notice of the position of the rebound adjustment 2 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -For the standard position see setting list. Position of the compression and rebound adjustment -Set the rebound position 1 , see KTM-Owners manual. -Assemble the rubber cap. -Set the compression position 2 , see KTM-Owners manual. 1 2 2-22 Repair manual WP Fork “Closed Cartridge” Art.No.: 3.211.199-E Explanation of the spring preload -Total spring length without the spacers, see chapter inspection of the spring! -Spring length with spacers 1 , see setting list. -Spring with the spacers. 1 . -The spring is assembled in the front fork leg. NOTE: the distance of “B” is less then the length of “A”. A – B = Spring preload A 1 1 B 2-23 Air release screw -Place the motorcycle on the stand. NOTE: the front wheel must be lift of the floor! -Unscrew the air release screw 1 of the screw cap on top of the front fork and tighten after approx. 10 seconds the air release screw. Recommended periodic maintenance and inspection of the 4860 SX/SXS/SMR front fork 1 A 100 liter fuel consumption is equivalent to approx. 15 operating hours Clean dust scrapers (after 1 hour) Bleed fork legs regularly – after every cleaning Check the inner tubes on scratches / leakage Visual check of damaging of the outer-tubes / replace if necessary Complete service without disass. the closed cartridge of the fork Complete service including the closed cartridge of the front fork Dismounting the fork -Place your motorcycle on a stand. -Notice the position of the front fork in the triple-clamps. NOTE: To remove the front fork. Read your KTM Instruction Manual or Workshop Manual. 3-3 Mounting the fork -Clean the innerside of the triple-clamps with brake cleaner. -Slide both fork legs into the triple-clamps. NOTE: Pay attention to the position of the fork legs. Standard riding height! NOTE: The maximum riding height is the level of the second groove! -Tighten the middle bolt of the lower triple clamp to a torque of 17 Nm! -Tighten the first bolt of the lower triple clamp to a torque of 17 Nm! -Tighten the third bolt of the lower triple clamp to a torque of 17 Nm!

Incoming search terms:

2002-2003 Honda GL1800/ A Frame Weld REPAIR PROCEDURE OVERVIEW

0

Filed Under (Honda) by admin on 14-12-2010

download
If your inspection identifies a crack or cracks in or on either Left or Right lower crossmember frame welds, STOP – call your DSM or TechLine for further instructions. • If your inspection reveals no cracks, proceed to REPAIR PROCEDURE. NOTE: Verification of repair can also be found in the Dealer Responsibility Report and on the Honda Interactive Network (iN). If you have any questions about verification, please contact TechLine before proceeding. IMPORTANT: For complete Dealer and Welder Repair procedures, refer to the following items: • 2002-2003 GL1800/A Frame Weld Safety Recall Dealer Booklet (S0510) • Frame Weld Inspection Chart (S0513) You MUST provide your TIG welder with the following items: • 2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual (S0511) • Welding Template Box (S0512) All of the above items were shipped to you with this Service Bulletin. If you need additional copies of the Dealer Booklet , Welding Manual , Welding Template Box , or Frame Weld Inspection Chart , you may order them at no cost from DDS at (440) 572-0725. For your reference, a brief repair procedure overview is provided below. Disassembly Overview You will be removing the following components from the vehicle as instructed in the Dealer Booklet : • Handlebar weights • Rear view mirrors • Swingarm pivot covers • Rider foot pegs • Seat • Side covers/Engine side covers • Fairing pockets • Fairing molding • Meter panel • Top shelter • Battery • Fuel tank • Main wiring harness ground • Front lower fairing • Front exhaust pipe protector • Muffler/exhaust pipe • Antenna Whip(s) • Coolant reserve tank • Center stand NOTE: You will need to remove any accessories that may contact the ground during the Welding and Re-assembly procedures. IMPORTANT: You MUST cover the following with RED duct tape for welder identification pur- poses: • Negative (-) and positive (+) battery cables • Fuel return hose end • Fuel feed hose end • Main wiring harness ground • Alternator • Exhaust ports Welding Overview A qualified TIG welder will weld the frame following the procedures in the 2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual . Re-assembly Overview You will be inspecting the new TIG welds, painting the frame, and re-assembling the vehicle as detailed in the Dealer Booklet and Frame Weld Inspection Chart (S0513)

Incoming search terms:

2001-2002 Honda GL1800/A Frame Weld Inspection PROCEDURE

0

Filed Under (Honda) by admin on 22-04-2011

download
IMPORTANT: During these procedures you may be using and referring to the following materials, originally sent to you with Service Bulletin GL1800 #14. • 2002-2003 GL1800/A Frame Weld Safety Recall Dealer Procedures (S0510) • Frame Weld Inspection Chart (S0516) • 2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual (S0511) • 2002-2003 GL1800/A Frame Weld Safety Recall Cracked Weld Repair Manual (S0515) • Welding Template Box (S0512)If you need additional copies of these materi- als you may order them at no cost from Resolve at (440) 572-0725. 1. Position the motorcycle on a firm, level surface, in an area where there is enough room to safely lay it on its left side. 2. Remove the left side mirror by following the nstructions on page 2-7 of the Service Manual. 3. Remove the left engine side cover by following the nstructions on page 2-5 of the Service Manual. 4. Remove the antenna whip(s). 5. Remove the coolant reserve tank by fol- lowing the instructions on page 6-7 of the Service Manual. 6. Place thick, non-abrasive padding (such as furniture blankets) on the ground to protect the motorcycle when you lay it on its side. 7. Lock the handlebars to the RIGHT, using the ignition key. 8. Using two people, gently lay the motor- cycle down on its LEFT side on the pad- ding. The motorcycle will first rest on the wheels and left engine and saddlebag guards. Continue to lean the motorcycle to the left until it rests on the left handlebar end and left engine and saddlebag guards. The motorcycle should be laying on the padding, with its engine guard, saddlebag guard, and handlebar end resting on the padding – no painted parts should be con- tacting the padding. 9. Clean the frame crossmember with acetone. 10. Draw a line on each side of the grinding template (S0512) 30 mm from the for- ward edge, stopping  between the two arrows, as illustrated below. 11. Put this template on the frame and, using a fine-tipped felt marker (such as a Sharpie), draw a 30 mm line on both crossmember welds. Start this line at the forward edge of the grinding template and stop between the two arrows as shown in the illustration on the next page.Now remove the grinding template

Incoming search terms: