2002 sportster 883 axle torque

You search Auto repair manual PDF 2002 sportster 883 axle torque, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2002 sportster 883 axle torque Direct Download speed 5282 Kb/s

  2002 sportster 883 axle torque Full Version speed 6162 Kb/s



HARLEY DAVIDSON DYNA AND SPORTSTER Chrome Front Wheel Spacers INSTALLATION ISNTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Block motorcycle underneath frame so front wheel is raised off the ground. 2. See Figure 1. Remove the upper (1) and lower (2) brake caliper mounting bolts and brake caliper(s) (3). Support caliper(s) using a rubber bungee cord. Be careful not to scratch fender paint. NOTES Do not operate front brake lever with the front wheel removed or the caliper piston may be forced out of piston bores. Reseating the piston requires disassembly of the caliper. Prior to removal, make note of existing left and right spacer location. The new spacers will be installed in the locations. 3. See Figure 3. On left side of wheel, remove axle nut (D), lockwasher (E) and washer (F). Perform the following: 4. Sportster and Dyna (except FXDWG) See Figure 2. Loosen the pinch bolt nut (1) and pull the the axle (2) free. Remove wheel and spacers. Leave bearing(s) in place. Discard spacers. 3 1 2 is04469 1. Brake caliper mounting bolt, long (top) 2. Brake caliper mounting bolt, short (bottom) 3. Brake caliper Figure 1. Caliper Mounting Bolts (Left Side) Dyna and Sportster 3 1 2 is04470 1. Pinch bolt nut 2. Axle 3. Pinch bolt Figure 2. Front Wheel Mounting (Dyna and Sportster Except FXDWG-Right Side) 5. See Figure 3. Obtain the new right (1) and left (2) chrome spacers from kit and install. 6. Apply a light coat of ANTI-SEIZE LUBRICANT (Harley- Davidson Part Number 98960-97) to the axle.
7. Place wheel between sliders and install axle. Verify that axle spacers on right and left side are properly installed. 8. See Figure 3. Install the washer (F), lockwasher (E) and nut (D) onto threaded end of axle (A). 9. In order to properly align the front fork, perform the fol- lowing: a. On the right side of the wheel, insert a 7/16 inch drill bit through the hole in the axle. While holding axle stationary, tighten axle nut to 50-55 ft-lbs (61.0-74.6 Nm) . b. Pull fork leg so that it just contacts drill bit. Tighten according to the following: c. Refer to Figure 2. Tighten the Axle Pinch Bolt Nut to 25-30 ft-lbs (33.9-40.7 Nm) . d. Remove drill bit from axle hole. 10. Follow instructions in Service Manual and install brake caliper to the sliders noting the following: •Loosely install long bolt to the top hole on fork leg. Install the short mounting bolt to the bottom hole and tighten to 28-38 ft-lb (38.0-51.5 Nm) . •Final tighten top bolt to 28-38 ft-lbs (38.0-51.5 Nm) . 11. Repeat Step 10 to install brake caliper on opposite side of wheel. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) 12. Pump brake lever to move pistons out until they contact both brake pads. Verify piston location against pads

Incoming search terms:

HARLEY DAVIDSON SOFTAIL CHROME REAR AXLE ADJUSTER AND COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 16-04-2011

download
INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. Block the motorcycle underneath the frame so the weight of the vehicle is off of the rear wheel, but do not raise the rear wheel off the ground. 2. Some models require loosening or removal of the muffler or mufflers in order to remove the rear axle. See the EXHAUST SYSTEM REMOVAL section of the Service Manual. Remove the saddlebags if desired for extra working clearance. See SADDLEBAG REMOVAL in the Service Manual. 3. See Figure 1. Remove the original axle adjustment bolts (1) and jam nuts (2) from both sides of the motorcycle and discard. NOTE On a bike that has been previously serviced, ensure that the axle has not been removed and re-installed from the left side (with the castle nut to the right of the wheel). If it has, the axle MUST be inserted from the right side of the motorcycle. 4. Remove the retaining pin (7), castle nut (5) and washer (4) from the left side of the axle (6). Discard the washer, but save the pin and nut for later re-assembly. 5 7 1 4 6 2 3 is04101 1. Axle adjust bolt 2. Jam nut 3. Axle adjuster collar 4. Washer 5. Castle nut 6. Rear axle 7. Retaining pin Figure 1. Rear Axle Hardware (Left Side Shown) 5. Tap the axle toward the right side of the motorcycle and remove. The belt adjuster collars (3) will fall loose as the axle is removed. The collars can be discarded. The wheel bearing spacers may also fall loose or be dislodged. Be sure to return these to their original position on the vehicle (short spacer on the right side, long spacer on the left). 6. Inspect axle components for damage or excessive wear, and replace as required

Incoming search terms:

Harley-Davidson Sportster 883/ 1200 Straightshot HS Exhaust system REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Loosen the heat shield clamps on both the front and rear exhaust pipes. This allows easier access to the head pipe mounting nuts. 2. Remove the two head pipe mounting nuts from each flange, located at the cylinder head. 3. Remove the two bolts from each muffler body which attach the muffler bodies to the mounting bar. 4. Remove the clamp bolt which mounts the rear head Page 1 of 4 D445N Rev. 1.0 Sportster 883/1200 Straightshot HS Exhaust system Part #17815 U S A Congratulations, you have purchased the finest exhaust system available for your motorcycle. Your VANCE & HINES exhaust system is designed and crafted for maximum performance, a perfect fit, a great sound and unbeatable style! Please follow the installation instructions below and if you have any questions, feel free to call our technical help line (562) 926-5291. Attention Installer: (if other than owner): Please forward this instruction sheet to the purchaser of this product. These instructions contain valuable information necessary to the end user. Tools required for installation: 3/16″ & 5/16″ Allen wrenches 3/16″ & 5/16″ Allen & 1/2″ sockets 3/8″ Ratchet & Extensions T30 Torx driver 1/2″ Wrench 5/16″ nutdriver/flat blade screwdriver Ft/lb. & In/lb. Torque wrenches Snapring pliers pipe to the belt drive cover bracket and carefully remove both exhaust pipes from the motorcycle. 5. Remove the drive belt cover and take the bracket off the rear cover bolt, it will not be re-used. 6. Loosen the brake rod at the rear eyelet using a T30 Torx driver. 7. Remove the exhaust mounting bar, saving the three mount bolts and washers for re-use. 8. Using snapring pliers, carefully remove the flanges and circlips from the stock exhaust system. Save for re-use. NOTE: If circlips look bent or twisted replace them with new circlips. VANCE & HINES EXHAUST SYSTEM INSTALLATION 1. Check condition of stock exhaust gaskets. Replace if damaged or worn. Vance & Hines recommends you replace your gaskets with Screamin’ Eagle gaskets part number 17048-98. 2. Install and tighten supplied mounting bracket (stamped 356-P) using stock bolts and washers (Figure 1). Torque to 30-33 Ft/Lbs. NOTE: Support the rear of the bracket during tightening to insure it is aligned with the bottom edge of the frame. 3. Re-install drive belt cover. Torque to 1 x 3/8″ bolt 30-33 Ft/Lbs. 2 x 1/4″ bolts 80-120 In/Lbs. 4. Re-install brake rod eyelet using blue thread locking compound (Loctite® 243). There is a 1/2″ clearance hole in the bracket to allow access for tightening brake rod eyelet. Torque to 120/180 In/Lbs. (Figure 1). 5. Remove header pipes and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark outside edge of each heat shield to show location of mounting clips where hose clamps will loop through (Figure 2). 6. Install circlips and flanges from the stock system onto both new head pipes.

Incoming search terms:

HARLEY DAVIDSON SOFTAIL REAR AXLE COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
INSTALLATION 1. 1988-1999 FLSTF Models: Remove rear muffler heat shield, loosen rear exhaust Torca clamp, then remove rear muffler from support following the instructions in the appropriate Service Manual. 2000 and Later Models: Remove exhaust system following the instructions in the appropriate Service Manual. NOTE In some cases, if bike has been previously serviced, the axle may have been removed and re-installed from the left side (with castle nut and cotter pin on the right). If this is the case, the axle must be removed and installed from the the right. If axle appears as original configuration (as in Figure 1), it is not necessary to loosen the rear axle nut or remove the cotter pin (or spring clip) from the rear castle nut. 2. All Models: See Figure 1. On the left side of the motorcycle, loosen the axle adjuster screw (1) and jamnut (2) just enough to be able to remove the jamnut. 3. 1988-1999 FLSTF Models Only: See Figure 2. On the right side (brake caliper side), use a T40 TORX drive to remove the two pin bolts from caliper. Remove caliper by gently rocking caliper back and forth to compress caliper piston, then carefully slide caliper off brake disc. Use cable strap or other suitable means to support caliper. 4. All Models: On the right side, loosen the axle adjuster screw and jamnut just enough to be able to remove the jamnut. 5. All Models: See Figure 3. On each side, place retainer clip (oriented as shown) and washer from kit over axle adjuster screw and replace jamnut. Turn in axle adjuster screw until it is in its original position against axle spacer, but leave jamnut loose. 1 2 4 3 is04788 1. Axle adjuster screw 2. Jamnut 3. Castle nut 4. Cotter pin (or spring clip) Figure 1. Rear Axle Hardware

Incoming search terms:

HARLEY DAVIDSON REAR SWINGARM AXLE COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) NOTE XL Sportster 883 and XL1200R models may require loosening or removal of the rear muffler in order to install the right side rear axle cover. See the EXHAUST SYSTEM REMOVAL section of the Service Manual. 1. Support the vehicle, and loosen or remove the rear muffler if necessary. XL Sportster 883 and XL1200R models: Remove the right-side lower shock absorber mounting bolt. Save for re-installation. All other models: Remove and discard the right-side lower shock absorber mounting bolt. 2. Swing the bottom of the shock absorber out of the way. Position the right-side swingarm axle cover (2) over the swingarm and behind the shock absorber. 3. Reposition the shock absorber. XL Sportster 883 and XL1200R models: Install the shock absorber mounting bolt removed in Step 1. All other models: Install the shoulder bolt (3) from the kit. All models: Tighten the bolt to 45-50 ft-lbs (61-68 Nm) . NOTE When torquing the bolt, align two of the bolt-head flats parallel to the ground. This will allow proper orientation of the bar and shield logo on the bolt cover. 4. Position the bolt cover (4) over the bolt head (3) with the Bar-and-Shield logo oriented upright, and lock in place with the set screw (5). Tighten securely. Reposition and tighten the muffler per the Service Manual instructions. 5. Remove and discard the left-side lower shock absorber mounting bolt. Move the bottom of the shock absorber out of the way. Position the left-side swingarm axle cover (2) over the swingarm and behind the shock absorber. 6. Reposition the shock absorber and install the shoulder bolt from the kit. Tighten to 45-50 ft-lbs (61-68 Nm) , aligning two of the bolt head flats parallel to the ground. 7. Position the bolt cover over the bolt head with the Bar-and- Shield logo oriented upright, and lock in place with the set screw. Tighten securely

HARLEY-DAVIDSON Sportster Solid Axle Suspension Owner's Maintenance Notes

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
1. Tire Pressure and Rotation : Keep the nominal tire pressure at about 24-26psig. It is not necessary to periodically rotate the trike tires unless you experience unusual tire wear. 2. Bearing Lubrication . Your Swing Arm, external differential, and axle bearings are sealed and do not require greasing. However, should you experience unusual differential or axle bearing noise you should take your trike to a Champion Trike Dealer or to your motorcycle mechanic for a checkup. 3. Body Lubrication . There are no grease fittings on the trike body and no required body lubrication points. 4. Differential lubrication . Your differential is a sealed unit and comes filled with high-pressure grease. No maintenance is required. 5. Brakes . Check your brake system fluid level every 3,000 miles and top-off as necessary. Inspect rear disc brake pads every 10,000 miles and replace as necessary. Pads are Volkswagen Part # D101P. 6. Drive Train . Inspect your drive belt as recommended in your motorcycle Owner’s Manual. When properly tensioned after the trike conversion, the belt should “deflect” approximately ¾”-1″ with a new belt or 1″ to 1-1/2″ with a used belt of total vertical movement. Do not use commercial belt dressing compounds on the belt except for Harley Davidson Poly-Oil, PN 99860- 81. These compounds are designed for friction, not toothed, belts and can collect dirt and sand. 7. Suspension System. The suspension is a “Zero Flex” solid axle with high performance adjustable pre-load coilover shocks. The suspension system is designed to give you the best ride with a load of no more than 400 pounds. 8. EZ-Steer (rake kit) : If your trike is equipped with Champion’s EZ-Steer, the bearings are a wear item. You should follow your motorcycle manufacturer’s recommended front-end triple-tree maintenance requirements. Generally these call for an initial service at 1,000 miles followed by periodic maintenance at 10,000 mile intervals

HARLEY DAVIDSON REAR AXLE-NUT COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
REAR AXLE-NUT COVER KIT GENERAL Kit Number 41704-09, 41705-09, 41706-09 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section (English only). Additional Parts Required The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 1 and Table 1. INSTALLATION NOTES The shorter axle-nut cover mounts to the right side of the motorcycle. Axles that have been removed for service, replacement or repair may have been assembled in reverse orientation from their stock design. Axle-nut covers may not fit properly on reversed axles. Refer to the appropriate Service Manual for correct axle orientation. 1. Adjust the position of the exhaust system (if necessary) to provide axle-nut clearance. 2. Position each axle-nut cover over the appropriate axle nut. 3. The skull version nut covers have two set screws per cover. Position the logo and snug up one set screw to hold in place and the other to prevent rotation. 4. Tighten the axle-nut cover set screws to 70 in-lb (7.9 Nm) . NOTE The set screws in this kit are treated with a thread-locking compound. When replacing or re-installing the set screws (2), apply Loctite® 243 (Blue) Threadlocker and Sealant (Harley- Davidson Part Number 99642-97) to the set screw threads. SERVICE PARTS

Incoming search terms:

2001-2002 GL1800 A ABS Speed Sensor Wire Clamp Location INSPECTION/ REPAIR PROCEDURES

0

Filed Under (Honda) by admin on 29-01-2011

download
1. If the VIN is within the preceeding range, inspect the front ABS speed sensor wire clamp according to the following illustrations. 2001-2002 GL1800A ABS Speed Sensor Wire Clamp Location INCORRECT Installation CORRECT Installation Service Bulletin American Honda Motor Co., Inc. 2001-2002 GL1800 ABS Speed Sensor Wire Clamp Location 0112 GL1800 #9*GL1800 #9*0112*2001-2002 GL1800 ABS Speed Sensor Wire Clamp Location*GL1800, ABS Speed Sensor Wire Clamp Location*Motorcycle*1800 2 of 2 ©2001 American Honda Motor Co., Inc. – All Rights Reserved GL1800 #9 DECEMBER 2001 IDENTIFICATION There is no identification mark associated with this Service Bulletin. PARTS INFORMATION There is no parts information associated with this Service Bulletin. WARRANTY INFORMATION The normal warranty claim submission requirements apply. Submit one warranty claim per VIN with the following information only: Inspected and REPAIRED Template: GL#9 Hours: 0.2 hours Parts: None If the clamp is installed correctly on top of the speed sensor, no further action is necessary. 3. If the clamp is installed incorrectly under the speed sensor, remove and reinstall the clamp and speed sensor correctly. Torque the bolts,. Torque: 12 N • m (1.2 kgf • m, 9 lbf • ft) If the speed sensor wire clamp for the front ABS speed sensor is installed incorrectly, the ABS speed sensor air gap may be out of specification. This does not affect ABS speed sensor operation, but the clamp should be installed correctly. Inspect and repair all affected units using the Inspection/Repair procedures listed below. Inspect all unsold units and customer units brought in for service. AFFECTED UNITS 2001-2002 GL1800A units as follows: MODEL 2001 GL1800A All units 2002 GL1800A 1HFSC474*2A100001 – 1HFSC474*2A101643 * = denotes check digit Any unit in the above VIN range may be affected and should be inspected according to the procedures in this Service Bulletin. All units outside of the above VIN range do not require inspection. CUSTOMER NOTIFICATION There is no customer notification associated with this Service Bulletin.

Incoming search terms:

2008 FLT Police Models Service Manual Supplement

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
ITEM SERVICED 14-21 ft-lbs (19.0-28.5 Nm) Drain plug torque Engine oil and filter 4 qt. (3.8 L) Oil capacity Hand tighten 1/2-3/4 turn after gasket contact Filter 63798-99A Chrome filter part number 63731-99A Black filter part number FORMULA+ TRANSMISSION AND PRIMARY CHAIN LUBRICATION (Part No. 99851-05) Lubricant type and capacity Primary chain lubricant Wet: 38 oz. (1124 ml) Dry: 45 oz. (1331 ml) 14-21 ft-lbs (19.0-28.5 Nm) Primary chaincase drain plug torque 1/2-1 turn Adjuster screw free play Clutch adjustment 72-120 in-lbs (8.1-13.6 Nm) Adjuster screw locknut torque 1/16-1/8 in. (1.6-3.2 mm) Free play at hand lever 84-108 in-lbs (9.5-12.2 Nm) Clutch inspection cover torque Dipstick at FULL with motorcycle on jiffy stand and filler plug resting on threads. Lubricant level Transmission lubricant FORMULA+ TRANSMISSION AND PRIMARY CHAIN LUBRICATION (Part No. 99851-05) Lubricant type and capacity 32 oz (0.95 liters) 14-21 ft-lbs (19.0-28.5 Nm) Transmission drain plug torque 25-75 in-lbs (2.8-8.5 Nm) Transmission filler plug/dipstick torque Front: 36 psi (248 kPA) Pressure: solo rider Tire pressure and wear Rear: 36-40 psi (248-276 kPA) Replace if less than 1/32 in. (0.8 mm) of tread pattern Wear 55 in-lbs (6.2 Nm) minimum Spoke nipple torque Wheel spokes 99953-99A (12 oz.) D.O.T. 4 hydraulic brake fluid part number Brake fluid level Front: 0.20 in. (5.0 mm) Fluid level (from top of master cylinder reservoir) Rear: 0.26 in. (6.5 mm) Front: 7-10 in-lbs (0.8-1.1 Nm) Master cylinder reservoir cover screw torque Rear: 12-15 in-lbs (1.4-1.7 Nm) 0.016 in. (0.4 mm) Minimum brake pad thickness Brake pads and discs 75-102 in-lbs (8.5.-11.5 Nm) Brake caliper pad pin torque Front: 0.18 in. (4.5 mm) Minimum brake disc thickness Rear: 0.25 in. (6.3 mm) 0.008 in. (0.2 mm) Maximum brake disc lateral runout (warpage) 10 lb. (4.5 kg) Upward force applied at midpoint of bottom belt strand Drive belt deflection 3/8-7/16 in. (9.5-11.1 mm) FLHTP 1/4-5/16 in. (6.4-7.9 mm) FLHP/FLHPE 40-60 in-lbs (4.5-6.8 Nm) Air cleaner cover bracket screw torque Air cleaner 36-60 in-lbs (4.1-6.8 Nm) Air cleaner cover screw torque LOCTITE MEDIUM STRENGTH THREADLOCKER 243 (BLUE) Air cleaner cover screw Threadlocker Part No. 99642-97 (6 ml) LUBIT-8 SUPER OIL, Part No. 94968-85TV (1/4 fl. oz.) Lubricant part number Clutch cable 35-45 in-lbs (4.0-5.1 Nm) Handlebar switch housing screw torque

Incoming search terms:

INSTRUCTIONS ON HOW TO R & R YOUR Swingarm

0

Filed Under (Tips and Review) by admin on 12-12-2010

download
• Upgrade Your Pre- 2002 FL Or FXR Rear Fork & Get Rid Of The Crappy & Dangerous (Cleve Blocks) & Replace Them With A Stable System. • R & R your Swing Arm, Belt Drive, Swing Arm Pivot Shaft, and Rear Wheel. The paragraphs below are a photo journey into the replacement of a FL or FXR swing arm. To upgrade the pre 2002 FL, here is a How-To on cheaply replacing the poor parts Harley stuck you with. Now – Let’s Get Er’ Done • Pre- 2002 had weak swing arms and are known to fail. The cleve blocks are the cause of “Rear Steer” or “Rear Fork Deflection”. Harley came up with a patch in 2002, using bearings. Because the pre 2002 transmissions have a 5/8″ mounting hole for the 5/8″ swing arm pivot shaft, a conversion unit has been made. No transmission removal for boring is necessary. Under no circumstances, do I recommend drilling out the transmission case with a hand drill. The drill will “wander” (drift)! • Solution: Go to either a trike shop/manufacturer, e-Bay, or shop and buy a new style swingarm. Harley made an additional upgrade in 2007, try and buy this type 2007 & above). If upgrading to a 2008, Harley use 25mm (smaller than 1″) axles & wheel bearings, you will have to use 25mm bearings. With that said, let’s get on with it. • In the case of a 2007 swingarm; buy and do not pay over $40 for the swing arm and axle. You must use the corresponding axle as a ¾” axle set-up is different (along with wheel bearings & spacers). You positively can not use a pre -2002 HD stock wheel because the wheel bearing spacer will fit into the wheel. Buy 2002 & above style wheels as they (9 spoke) are cheep. • You are going to have to either bore out your stock rear caliper bracket or better still, upgrade your whole rear brake to the new model & sell yours on e-Bay. • I recommend doing the following before hand and have it ready for installation; Remove bearings et al. from the 2002 & later swing arm via press. Bike Work: • Jack up your bike using a center jack. Secure the bike so it will not fall over. You can also use a motorcycle jack. I use a motorcycle dolly

Incoming search terms: