2003 camry coolant capacity

You search Auto repair manual PDF 2003 camry coolant capacity, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2003 camry coolant capacity Direct Download speed 5282 Kb/s

  2003 camry coolant capacity Full Version speed 6162 Kb/s



2001 – 2003 Prius 2003 4Runner, Camry, Land Cruiser and Sequoia VEHICLES EQUIPPED WITH TRANSPONDER ECU

0

Filed Under (Toyota Manuals) by admin on 07-10-2011

download
When replacing the ECM (SAE term: PCM) or the Transponder ECU a “handshake” procedure must be performed. This ECU ID communication is necessary to enable the Transponder ECU and the ECM to recognize each other before the vehicle will start. Complete ECU communication using the following steps: 1. Insert a Master key into the ignition cylinder. 2. Turn the ignition ON (engine OFF). 3. Short Tc and CG terminals of DLC3 using the Diagnostic Check Wire (SST 09843-18020 or equivalent) and leave for 30 minutes. 4. After 30 minutes, turn the ignition OFF and remove check wire from DLC3. 5. Register any additional keys as necessary. 6. Start the vehicle to confirm successful ECU communication. Key Programming: To program or delete a key, a registered Master key is necessary unless the Transponder ECU has been reset or replaced. The Transponder ECU system incorporates a black “Master” key and a gray “Sub” key. The process during registration of these two keys is identical. The key itself now determines if it functions as Master or Sub, not the registration procedure. The maximum number of allowable Master and Sub keys vary by model. Refer to the chart below.

Incoming search terms:

2003 SUZUKI SV 1000 Service Manual

0

Filed Under (Suzuki) by admin on 26-02-2011

download
HOW TO USE THIS MANUAL TO LOCATE WHAT YOU ARE LOOKING FOR : 1. The text of this manual is divided into sections . 2. The section titles are listed in the GROUP INDEX . 3 . Holding the manual as shown at the right will allow you to find the first page of the section easily . 4. The contents are listed on the first page of each section to help you find the item and page you need . COMPONENT PARTS AND WORK TO BE DONE Under the name of each system or unit, is its exploded view . Work instructions and other service information such as the tightening torque, lubricating points and locking agent points, are provided . Example: Front wheel SYMBOL Listed in the table below are the symbols indicating instructions and other information necessary for servicing. ENGINE OIL SUZUKIrecommends the use of SUZUKI PERFORMANCE 4 MOTOR OIL or an oil which is rated SF or SG under the API (American Petroleum Institute) service classification. The recommended viscosity is SAE 1 OW-40 . If an SAE 1 OW-40 oil is not available, select an altematice according to the right chart . BRAKE FLUID Specification and classification: DOT 4 A WARNING Since the brake system of this motorcycle is filled with a glycol-based brake fluid by the manufacturer, do not use or mix different types of fluid such as silicone-based and petroleum-based fluid for refilling the system, otherwise serious damage will result . Do not use any brake fluid taken from old or used or unsealed containers . Never re-use brake fluid left over from a previous servicing, which has been stored for a long period. FRONT FORK OIL Use fork oil L01 or an equivalent fork oil . GENERAL INFORMATION 1-5 ENGINE COOLANT Use an anti-freeze/engine coolant compatible with an aluminum radiator, mixed with distilled water only . WATER FOR MIXING Use distilled water only . Water other than distilled water can corrode and clog the aluminum radiator . ANTI-FREEZE/ENGINE COOLANT The engine coolant perform as a corrosion and rust inhibitor as well as anti-freeze . Therefore, the engine coolant should be used at all times even though the atmospheric temperature in your area does not go down to freezing point. Suzuki recommends the use of SUZUKI COOLANT anti-freeze/engine coolant. If this is not available, use an equivalent which is compatible with an aluminum radiator . LIQUID AMOUNT OF WATER/ENGINE COOLANT

Incoming search terms:

2007 Camry And Camry SOUND DISTORTION ON AM RADIO

0

Filed Under (Toyota Manuals) by admin on 25-10-2011

download
some customers may experience a condition where certain AM radio stations have a distorted sound even though the signal from the local AM station is strong. A revised radio has been developed to address the condition. Use the following repair procedure to replace the radio. 2007 model year Camry vehicles produced BEFORE the Production Change Effective VINs shown below. 2007 model year Camry HV vehicles

2007 4Runner, Camry, Camry HV, Sienna, and Solara NAVIGATION SYSTEM VOICE RECOGNITION SYSTEM TALK BACK MALFUNCTION

0

Filed Under (Toyota Manuals) by admin on 19-10-2011

download
Order a map disc through DENSO by calling 1-888-668-2900. Provide DENSO the TSB reference number, dealer code, and vehicle information when ordering this revised map disc. 2. Replace the navigation map disc. Refer to the Technical Information System (TIS), 2007 model year applicable model Repair Manual: Audio/Visual/Telematics – Navigation/Multi info Display – “Navigation: Navigation ECU: Removal” Audio/Visual/Telematics – Navigation/Multi info Display – “Navigation: Navigation ECU: Installation” 3. Cut the original navigation map disc in half and dispose of it

Camry, Camry HV 2007 – 2009 Sunvisor – Removal & Installation Procedures

0

Filed Under (Toyota Manuals) by admin on 27-05-2011

Download

Partially install the bracket cover into the sunvisor bracket making sure both temporary set claws are
engaged as shown in Figure 5. NOTE
Make sure to ONLY partially install the bracket cover into the bracket during installation,
because damage to the clip, sunvisor mount or roof sheet metal tabs may occur if the bracket
cover is fully in the sunvisor bracket.
2. Install the sunvisor assembly into the opening in the sheet metal roof panel by grasping the
sunvisor assembly with two hands and pushing the bracket upward as shown in Figure 6.

2002 – 2003 Camry A/ C PERFORMANCE & DURABILITY IMPROVEMENT

0

Filed Under (Toyota Manuals) by admin on 28-10-2011

download
Start the engine. B. Inspect the compressor for a metallic rattle sound. a. Check if there is a metallic rattle sound from the compressor when the A/C switch is on. b. If a metallic rattle sound is heard, replace the compressor assembly. Please follow the instructions in the repair manual for compressor removal and replacement: V6 engine: page 55-50 L4 engine: page 55-57 C. Inspect magnetic clutch condition. a. Check the magnetic clutch for signs of overheating. b. If there are signs of overheating, replace the magnetic clutch. 2. Install Air Conditioner Wire. A. Remove instrument panel under cover sub-assembly No. 1, glove compartment door pad, instrument panel sub-assembly lower and heater to foot duct No. 1. B. Remove the cooler thermistor connector from the blower unit.

2003 – 2004 4Runner & Tundra, 2004 Camry, Highlander, Sienna & SolaraREPAIR MANUAL SUPPLEMENT LEV II EVAP SYSTEM CHECK

0

Filed Under (Toyota Manuals) by admin on 24-10-2011

download
this TSB provides detailed instructions for a new LEV II EVAP System Check function using the Diagnostic Tester. The LEV II System Check allows the Diagnostic Tester to display the fuel tank vapor pressure as the EVAP VSV and the CCV are operated in a specific six-step pattern. Problems with the EVAP system are quickly isolated by observing the change in vapor pressure during each step. Once the vehicle condition is corrected, the LEV II System Check can also be used to confirm the repair before the vehicle is returned to the customer. The inspection procedure using the LEV II System Check (LEV II SYS CHECK) is described in this bulletin. This function is available using a Diagnostic Tester with version 11.0a software (or newer

Incoming search terms:

2003 SUZUKI SV 650 COOLING AND LUBRICATION SYSTEM SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
COOLING CIRCUIT INSPECTION Before removing the radiator and draining the engine coolant, inspect the cooling circuit for tightness. • * Remove the cowling. (SV650S) (C-7–7-6) • * Loosen the radiator cap stop screw 10 . (SV650) • * Remove the radiator cap O2 and connect the radiator tester to the filler. A WARNING Do not remove the radiator cap when the engine is hot. • * Give a pressure of about 120 kPa (1 .2 kgf/cm2,17.0 psi) and see if the system holds this pressure for 10 seconds . • * If the pressure should fall during this 10-second interval, it means that there is a leaking point in the system . In such a case, inspect the entire system and replace the leaking component or part. A WARNING When removing the radiator cap tester, put a rag on the filler to prevent spouting of engine coolant. CAUTION Do not allow the pressure to exceed specified pressure, or the radiator can be damaged. COOLING AND LUBRICATION SYSTEM 6-3 6-4COOLING AND LUBRICATION SYSTEM RADIATOR REMOVAL • * Remove the cowling. (SV650S) ( r- 7-7-6) • * Drain engine coolant. (r– 72-20) • * Disconnect the right and left radiator hoses from the radiator. • * Disconnect the siphon hose from the radiator. • * Disconnect the horn lead wires. rI .rr • * Remove the radiator lower mounting bolt. • * Disconnect the cooling fan motor and its thermo-switch lead wire coupler 10. • * Remove the radiator by upper mounting bolt. • * Remove the cooling fan. • * Disconnect the cooling fan thermo-switch. • * Remove the cooling fan thermo-switch. • * Remove the horn. CAUTION When removing the horn, hold the nut by spanner to prevent the horn bracket distortion. COOLING AND LUBRICATION SYSTEM 6-5 INSTALLATION • * Install the cooling fan and horn. 0 Cooling fan/horn mounting bolt: 8 N .m (0.8 kgf-m, 6 .0 Ib-ft) • * Install the cooling fan thermo-switch. ( l”76-9) • * Install the siphon hose to the radiator. • * Install the radiator in the reverse order of removal. • * Route the radiator hoses properly. (=9-22) 9-22) • * Install the drain plug with a new sealing washer and pour engine coolant. (=2-20) • * Bleed air from the cooling circuit. (r– 72-21) • * Install the cowling. (SV650S)

Incoming search terms:

2002-2003 Honda GL1800/ A Frame Weld REPAIR PROCEDURE OVERVIEW

0

Filed Under (Honda) by admin on 14-12-2010

download
If your inspection identifies a crack or cracks in or on either Left or Right lower crossmember frame welds, STOP – call your DSM or TechLine for further instructions. • If your inspection reveals no cracks, proceed to REPAIR PROCEDURE. NOTE: Verification of repair can also be found in the Dealer Responsibility Report and on the Honda Interactive Network (iN). If you have any questions about verification, please contact TechLine before proceeding. IMPORTANT: For complete Dealer and Welder Repair procedures, refer to the following items: • 2002-2003 GL1800/A Frame Weld Safety Recall Dealer Booklet (S0510) • Frame Weld Inspection Chart (S0513) You MUST provide your TIG welder with the following items: • 2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual (S0511) • Welding Template Box (S0512) All of the above items were shipped to you with this Service Bulletin. If you need additional copies of the Dealer Booklet , Welding Manual , Welding Template Box , or Frame Weld Inspection Chart , you may order them at no cost from DDS at (440) 572-0725. For your reference, a brief repair procedure overview is provided below. Disassembly Overview You will be removing the following components from the vehicle as instructed in the Dealer Booklet : • Handlebar weights • Rear view mirrors • Swingarm pivot covers • Rider foot pegs • Seat • Side covers/Engine side covers • Fairing pockets • Fairing molding • Meter panel • Top shelter • Battery • Fuel tank • Main wiring harness ground • Front lower fairing • Front exhaust pipe protector • Muffler/exhaust pipe • Antenna Whip(s) • Coolant reserve tank • Center stand NOTE: You will need to remove any accessories that may contact the ground during the Welding and Re-assembly procedures. IMPORTANT: You MUST cover the following with RED duct tape for welder identification pur- poses: • Negative (-) and positive (+) battery cables • Fuel return hose end • Fuel feed hose end • Main wiring harness ground • Alternator • Exhaust ports Welding Overview A qualified TIG welder will weld the frame following the procedures in the 2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual . Re-assembly Overview You will be inspecting the new TIG welds, painting the frame, and re-assembling the vehicle as detailed in the Dealer Booklet and Frame Weld Inspection Chart (S0513)

2001 – 2004 Camry, Highlander, Solara & 2004

0

Filed Under (Toyota Manuals) by admin on 12-10-2011

download
2004 model year Camry, Highlander, Solara and 2004 model year RAV4 vehicles with the 2AZ-FE engine may exhibit squealing and/or rattling noises coming from the engine compartment during vehicle operation especially after a cold soak. The belt tensioner assembly has been improved to correct this condition. 2001 – 2004 model year Camry, Highlander and Solara vehicles equipped with 2AZ-FE engines produced BEFORE the Production Change Effective VINs shown below. 2004 model year RAV4 vehicles produced BEFORE the Production Change Effective VINs shown below. MODEL ENGINE LINE PRODUCTION CHANGE EFFECTIVE VIN TMMK Line 1 4T1BE3#K#4U358206 Camry TMMK Line 2 4T1BE3#K#4U914052 y 2AZFE Tsutsumi JTDBE3#K#40296732 Highlander 2AZ-FE TMK JTE#D2#A#40100501 Solara TMMK 4T1CE3#P#4U914074 RAV4 Tahara JTE#D2#V#40029797 PREVIOUS PART NUMBERCURRENT PART NUMBER PART NAME QTY 16620-28010 16620-28011 Tensioner Assembly, V-ribbed Belt 1 OP CODE DESCRIPTION TIME OFP T1 T2 EG8001 R & R Accessory Belt Tensioner 0.9 16620-28010 91 55 Applicable Warranty*: This repair is covered under the Toyota Comprehensive Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle’s in-service date. *Warranty application is limited to correction of a problem based upon a customer’s specific complaint

Incoming search terms:

Incoming search terms: