2003 harley electra glide turn on radio

You search Auto repair manual PDF 2003 harley electra glide turn on radio, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2003 harley electra glide turn on radio Direct Download speed 5282 Kb/s

  2003 harley electra glide turn on radio Full Version speed 6162 Kb/s



HARLEY-DAVIDSON TURN SIGNAL MIRRORS WITH CONVEX GLASS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 03-04-2012

download
STEP 1 Remove the stock mirrors. LEFT SIDE: STEP 2 Choose the longest Allen bolt from the hardware kit that passes through the hand control, a split lock washer, an internal tooth star washer, the turn signal mount (if applicable), and still provides maximum thread engagement in the mirror stem without bottoming out. Mount the mirror with the hardware listed above. (Place the star washer between the mirror stem and the hand control). RIGHT SIDE: STEP 3 If the turn signals are not mounted under the mirror, proceed in the same manner as the left side. STEP 4 If the turn signal is mounted under the mirror proceed as follows: Apply Red loctite to the short threaded end of the special mounting stud. Screw this end securely into the mirror stem. -cont.- 1432-22HD-0105 TURN SIGNAL MIRRORS WITH CONVEX GLASS 1432 INSTALLATION Illiana CUSTOMER SERVICE 877.370.3604 (toll free) INSTALLATION QUESTIONS techsupport@kuryakyn.com or call 715.247.2983 WARRANTY Küryakyn™warrants that any Küryakyn product sold hereunder, if properly installed, maintained and operated under normal conditions, shall be free from any defects in materials and workmanship for a period of one (1) year from the date the Küryakyn products are sold to the customer. CONSEQUENTIAL DAMAGES: Küryakyn shall not be liable for any consequential or incidental damages. ABOUTOURCA TA LOG You’ll find all our innovations for H-D, GL and Metric Cruisers in our annual catalogs. Order online today-select the “CATALOGS” icon. Each Küryakyn™ product comes with a Proof-of-Purchase good for a complimentary catalog. Details in packaging. Be sure to ask your local dealer about other Küryakynproducts, the motorcycle parts and accessories designed for riders by riders. ©2004 Küryakyn USA™All Rights reserved.
STEP 5 Remove the turn signal assembly from the stock mirror. Pay close attention to how the stock turn signal ball joint assembly comes apart as this will aid in re-assembly. STEP 6 Place a star washer over the mounting stud and insert the mirror and stud assembly into the hand control. Re-assemble the turn signal ball joint being sure the turn signal light is aimed to your liking. You may wish to consult your H-D shop manual when re-assembling this ball joint. WIRING: STEP 7 Determine where you wish to splice into the H-D turn signal wiring harness. Cut the harness or strip back an appropriate amount to vinyl wire covering and prepare the wires for splicing. Make the wire connections as follows: Wires from Turn Signal Mirror H-D Turn Signal Wire Colors Black – (Ground) Black (Ground) Red – (Running Light) Blue (Running Light) White (Turn Signal) Violet (Turn Signal) If a more pronounced flash is desired, one may eliminate the running light function and wire as follows: Black Black Red and White together Violet If these turn signal mirrors are to be used in conjunction with stock front turn signals, no load equalizer will be required. If the turn signal mirrors are REPLACING stock front turn signals, in most cases, a load equalizer is required. For easiest access we suggest installing the load equalizer under the seat; tapping into the main wiring harness that leads to the tail lights and rear turn signals.

Incoming search terms:

HARLEY DAVIDSON V-ROD CHROME REAR TURN SIGNAL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION Prepare the Motorcycle 1. Remove the right cover and the maxi-fuse. 2. Follow Service Manual instructions to remove the air box cover. Remove the Existing Rear Turn Signals 1. For 2006 and Earlier Models: See Figure 1. Insert a screwdriver into middle of hole of license plate light cover. Push forward to release tail lamp housing retaining clip. 2. See Figure 3. Identify the white left [19] (1) and black right [18] (2) 2 pin rear turn signal connectors. 3. See Figure 6. To separate the rear turn signal connector, press the button (1) and separate the pin terminal housing from the socket terminal housing. 4. On the socket terminal housing, press the latch (2) aside and open the secondary lock (3). 5. To remove the rear turn signal wires from the socket terminal housing, insert a pin (6) into the front socket cavity. Compress the tang (4) while gently pulling the wire and socket terminal (5) from the back. 6. See Figure 7. Inside the fender, remove the fasteners (1) and the turn signal support plate (2). Pull the turn signal wiring through holes in license plate mounting bracket and remove turn signals. 7. Repeat for the opposite turn signal. 1. For 2007 and Later Models: See Figure 2. Open seat and remove the nut and washer (3), seat post (2), passenger pillion and passenger seat (1) per the instructions in the Service Manual. 2. See Figure 4. Identify the left (1) and right (2) rear turn signal wires and 6 pin rear turn signal connector [94]. 3. See Figure 6. To separate the rear turn signal connector, press the button (1) and separate the pin terminal housing from the socket terminal housing. 4. On the socket terminal housing, press the latch (2) aside and open the secondary lock (3). 5. See Figure 5. Remove the turn signal wires from the 6 pin socket terminal housing. To remove the wires, insert a pin (6) into the front socket cavity. Compress the tang (4) while gently pulling the wire and socket terminal (5) from the back. Repeat for all four turn signal wires. Do not remove the license light wires from the socket terminal housing. 6. Gently pull the loose turn signal wires through the sheath toward the rear of the vehicle until completely removed from the sheath. 7. See Figure 7. Inside the fender, remove the fasteners (1) and the turn signal support plate (2). Pull the turn signal wiring through holes in license plate mounting bracket and remove turn signals. 8. Repeat for the opposite turn signal

Incoming search terms:

HARLEY DAVIDSON V-ROD CHROME TURN SIGNALS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-02-2011

download
INSTALLATION Prepare the Motorcycle 1. Remove the right cover and the maxi-fuse. 2. Follow Service Manual instructions to remove the air box cover. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 3. Follow Service Manual instructions given to remove the negative (-) battery cable from the negative (-) battery terminal. Remove the Existing Rear Turn Signals 1. See Figure 1. Insert a screwdriver into middle of hole of license plate light cover. Push forward to release tail lamp housing retaining clip. 2. See Figure 2. Identify the white left [19] (1) and black right [18] (2) 2 pin turn signal connectors. is 00231 Figure 1. Tail Lamp Housing 2 1 is00232 1. Left turn signal connector [19] (white) 2. Right turn signal connector [18] (black) Figure 2. Rear Turn Signal Connectors 3. See Figure 3. Press the button (1) and separate the pin terminal housing from the socket terminal housing. -J03601 1 4. On the socket terminal housing, press the latch (2) aside and open the secondary lock (3). 5. To release the socket terminal and wire, insert a pin (6) into the front socket cavity. Compress the tang (4) while gently pulling the wire and socket terminal (5) from the back. 6. See Figure 4. Inside the fender, remove the fasteners (1) and the turn signal support plate (2). Pull the turn signal wiring through holes in license plate mounting bracket (3) and remove turn signals. 7. Repeat for the opposite turn signal. Install Chrome Rear Turn Signals 1. See Figure 5. Assemble a chrome turn signal assembly (1) to a chrome lamp support (2) by feeding the wire leads through the wire hole in the lamp support. 2. Feed the wire leads and conduit through the front hole in the license plate bracket and through hole in the support plate (4) towards the front of the motorcycle. 3. Thread the bolt (3) through the center hole in the support plate, through the center hole in the license plate bracket, and through the hole in the chrome lamp support into the chrome turn signal. 4. Tighten the bolt to 100-150 in-lbs (11.3-16.9 Nm). 5. Route the turn signal wires between the license plate bracket and the inner fender. Access the wires through the tail lamp opening in the outer fender. 6. See Table 1. Identify the left and right connector socket housings and match the socket terminated colored leads to the cavities in the socket housing which correspond to the colored leads in the pin housing

Incoming search terms:

HARLEY DAVIDSON BLACK ENGINE GUARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL NOTE This Instruction Sheet covers several different Harley-Davidson models and years. Be sure to locate and follow the procedures that apply to the motorcycle receiving the new guard. For Models without Lower Fairings 1. Proceed to For All Models section. For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Remove the lower fairings following the instructions in the appropriate Service Manual. 2. When the lower fairings have been removed, proceed to For All Models section. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley-Davidson Genuine Motor Accessory Lower Fairings 1. See Figure 1. Remove the two black screws (1) that attach the fairing cap (2) to the lower fairing (5). Remove the cap. Set the parts aside for re-installation. 2. Remove the screw (7), rubber washer (8) and locknut (10) and the clamp (9) that attaches the bottom of the lower fairing to the engine guard and set aside. 3. Remove the two locknuts (3), U-bolt (6) and U-bolt retainer (4). 4. Remove the lower fairing by sliding it out from behind the engine guard. 5. Repeat Steps 1 through 4 for the opposite side. 6. Proceed to For All Models section. For Model FLTR/I (Road Glide) with Harley-Davidson Genuine Motor Accessory Lower Fairings Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery, negative (-) battery cable first, following the instructions in the appropriate Service Manual. 2. Remove the seat following the instructions in the appropriate Service Manual. 3. Remove the cable strap holding the clutch cable to the engine guard. 4. See Figure 2. Remove the TORX screw (8), rubber washer (9) and locknut (11) and the clamp (10) that attaches the bottom of the lower fairing (4) to the engine guard and set aside INSTALLATION 1. Hold the engine guard in position, and loosely fasten the top of the guard with the new hex socket screw and flat washer from the kit. 2. Install the bottom brackets to the motorcycle frame with the two new TORX screws and locknuts. 3. Tighten all three screws to 15-20 ft-lbs (20.3-27.1 Nm) . For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Install the lower fairings following the instructions in the appropriate Service Manual. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley- Davidson Genuine Motor Accessory Lower Fairings 1. Carefully place one lower fairing in position from behind the engine guard. 2. See Figure 1. Install the lower fairing to the top of the new engine guard with the U-bolt (6) from the back, through the holes at the top of the fairing. Install the retainer (4) in position on the U-bolt and secure to the engine guard with the two locknuts (3). Do not tighten the locknuts at this time. 3. Attach the bottom of the fairing to the engine guard with the clamp (9) removed earlier. Install the clamp around the engine guard in the direction shown, with the tabs toward the rear of the vehicle and the flat side of the clamp against the lower fairing. Insert the screw (7) through the lower fairing, rubber washer (8) and clamp (9). Secure the assembly with the locknut (10). Tighten to 12 ft-lbs (16.3 Nm) .

Incoming search terms:

HARLEY DAVIDSON FLHT ADVANCED AUDIO AM/FM/CD RADIO KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
INSTALLATION Remove Existing Equipment To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. 2. Remove outer fairing and windshield. Refer to OUTER FAIRING/WINDSHIELD REMOVAL in Service Manual. 3 2 1 is 00397 1. Socket head screw (4) 2. Radio support bracket (2) 3. Radio Figure 1. AM/ FM Radio Installation 3. See Figure 1. Using a long shank ball end socket (Snap- on® FABL6E or equivalent), remove the four socket head screws (1) to release the storage box from the left and right radio support brackets (2). Use the oblong holes in the fairing brackets to access the screws. Install Radio 1. Pull the storage box forward to remove the box from the opening in the inner fairing. Discard the storage box. 2. Position the radio (3) between the radio support brackets and push it into the opening in the inner fairing. 3. Align the threaded inserts in the sides of the radio with the oblong holes in the left and right radio support brackets. 4. Starting at the rear, install the four socket head screws previously removed. Alternately tighten the screws to 35- 45 in-lbs (4.0-5.1 Nm). 5. Plug the 23-place radio socket housing [27A] (part of the interconnect harness already installed on the vehicle) into the back of the radio. 6. Remove three T25 TORX® screws that hold the speaker opening cover on one end of the fairing. Discard the cover and screws. Install Speakers 1. See Figure 3. If the speaker (3) and adapter (4) are not assembled, or are assembled incorrectly, orient the speaker on the adapter and grille assembly so the speaker spade contacts are toward the side of the adapter with the widest edge. Snap the speaker into the adapter using finger pressure only.

Incoming search terms:

motorcycle Turn Signal Conversion Kit Installation Instructions

0

Filed Under (Tips and Review) by admin on 09-11-2010

download
1. Place motorcycle on solid, level ground and on center stand if equipped. 2. Remove your turn signal lens. Place it upside down and clean the lens interior with the supplied alcohol wipe. Allow to completely air dry. Note: the LEDs are mounted to the inside of the turn signal lens with the LEDs making direct contact with the lens. The supplied silicone is used to secure the LED board to the lens. It remains flexible but can be removed. Test fit the board in your lens prior to using silicone. 3. Using a small screwdriver, poke a small hole in the end of the tube of silicone. Place a dab of silicone on each of the 12 LEDs on the circuit board. CAUTION : Note the position of the metal pins on the back of the LED board, They must be located 90 degrees from where the holes are that secure the lens to the housing. See attached diagram. 4. Position the round circuit board over the inside of your turn signal lens with the LEDs facing down. Get the board as centered as possible. Allow the silicone to make contact with the inside of the lens and then push down and slightly rotate the board back and forth to allow the LEDs to make contact with the lens surface. Repeat other side. NOTE : the silicone will require 30 minutes in 70 degree weather to tack up. Full cure will occur within 24 hours. We suggest not riding for several hours if possible to allow the best adhesion. 5. You will need to access the following wires; running light (license plate can be used), brake lights, right turn and left turn. Disassemble the bike as needed to gain access to the wiring. Shop Tip: we have found that on the Yamaha Star Series and the Kawasaki Cruisers that installation is much easier when you remove the turn signal bar from the fender. On the Yamahas, there are 3 bolts holding the moustache in position. The wires will unplug from behind the license plate. On the Kawasakis, unplug the signals under the seat and bend the tabs under the fender to be able to remove the wires. 6. We have provided some tubing to slide over the wires so that when you re-install the bulb socket, our wires for the LED boards will not be pinched. This tube should be slid all the way into the turn signal housing. You may have to shorten the tubing for your installation. 7. You will need to run wires through the stem of the turn signal. You can see samples of how the various manufacturers signal housings come apart on our web site. Click on “Other Lighting Products” and then “Turn Signal Conversion Kits” and follow the link. We suggest placing the removed turn signal assembly on a towel on your work area. 7. You will need to leave 2″ of slack in the wires at the turn signal housing to allow for wire connection. 8. Reinstall the turn signal housing back on the motorcycle if removed. NOTE: both of the run/brake circuits must be used. You may shorten the wires only on the run/brake circuits as needed. Do not change the circuits under the heat shrink. T-Tap instructions. Lay the “donor” wire in the slot in the burgandy connector. Close and snap together with pliars. Strip some insulation off of the wire which will be tapping into the factory wire. Crimp one of the pink connectors on the bare wire and plug it into the burgandy T-Tap 9. Connect the green wires from the run/brake circuits to the bikes running lights. The 2 greens can be connected together. 10. Connect the blue wires from the run/brake circuits to the bikes brake lights. The 2 blues can be connected together. 11. Take one of the red wires from a run/brake circuit and connect it to one of the black with white stripe wires coming from one of the LED boards using the supplied red butt connector. Connect the other run/brake circuit red wire to the remaining black with white stripe wire on the other LED board. 12. Connect the black wire from the LED board on the right side of the bike to the right turn signal positive (+) wire on the motorcycle. 13. Connect the black wire from the LED board on the left side of the bike to the left turn signal positive (+) wire on the motorcycle. 14. Plug the wires into the LED boards. If you hold the turn signal lens so that you are viewing the back of the LED board, position the connectors on the board at the 12 o’clock (top) position. The connector on the left is the positive (+) terminal. Connect the red wire to it. Connect the black wire to the remaining connector on the right side. 15. Check operation. LEDs should come on with running lights. LEDs will brighten when brake lights are applied. LEDs will shut off when the amber turn signal comes on. 16. Should you have any problems, please see the troubleshooting chart on our website.* * 17. Reassemble bike

Incoming search terms:

HARLEY-DAVIDSON SPORTSTER TURN SIGNAL RELOCATION KIT INSTALLATION AND CLEANING INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 23-10-2010

download
Remove turn signals. Observe and mark “left” and “right” for reinstallation. h Turn signal bracket may be oriented forward or backward as required. 4. Install turn signal bracket between license plate and license plate bracket using 1/4”- 20 x 3/4” Hex cap screw, 1/4” SAE flat washers, and 1/4” – 20 locknuts. Note: For Bullet style turn signal light models refer to fig. 3, disassemble and discard turn signal extension and insert 8 x 22 x 5mm black plastic spacer in place of the extension. 5. Mount turn signals directly to bracket using 5/16” – 24 x 3/4” hex cap screws with 5/16” lock washers and 5/16” flat-washers. If original wire was inside stalk, remove plug and reroute wires to outside. For a clean installation remove top center mounting bolt on license plate bracket and run wires through this hole. h Information: Not all license plate mounts are grounded. In some cases, it may be necessary to run a ground wire to turn signal bracket. h WARNING: Some states may have minimum width requirements on motorcycle turn signals, so check your local laws. 6. Turn signal wires must be extended. We recommend splicing inside turn signal housing. Splice wires, one at a time, while observing color code. 7. Connect battery and test turn signals for function. SADDLEBAG INSTALLATION h Information: Bags will be easier to mount and remove if a small amount of silicone lubrication is applied to rubber mounting points.
Leatherlyke Refer to Figure 2. 9. Remove rear fender mounting bolt on each side and replace original bolt with the two 5/16” x 2 1/4” socket head bolts and 5/16” mounting spools with chamfer on spool under socket head bolt. Install 5/16” – 18 locknuts on inside of fender. Verify that adequate clearance exists between the ends of the bolts and tire. 10. Remove upper shock bolt and replace with (2) – 1/2″ x 1″ FLAT WASHERS and 1/2″ x 2 1/8″ hex spool & bolt assy.

HARLEY-DAVIDSON LARGE LED SILVER BULLETS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
PROCEDURE STEP 1*Remove the stock turn signal fixtures and cut the wires in a convenient and inconspicuous splice location. STEP 2**Place the split lock and flat washers on to the hollow bolts as shown in PIC. 1. Run the power leads through the hollow bolts and assemble the Silver Bullets to their mounts. See PIC. 2. STEP 3*Install the new Silver Bullet assemblies to the Mount Bar on the motorcycle. The stock 10-24 x 1/2″ socket head screws are to be re-used. PROCEDURE fOR AMBER DUAL CIRCUIT (fRONT WIRING) LED SILVER BULLET WIRE COLOR CODING IS AS fOLLOWS: Black — Ground Blue — Running Lights (power) Violet — Turn Signal (power) STEP 1 Turn key on. Test OEM stock front turn signal wiring with test light. STEP 2 Locate and mark the running light (power) wire. STEP 3 Individually activate the turn signals and mark the side-appropriate wires. STEP 4 Use the color code above to solder/connect the corresponding Silver Bullet wires to your Join like colored wires on the Silver Bullets and the bike’s turn signal harnesses. Insulate your connections. Route the wires safely out of harms way and tie the wires in place with nylon cable ties. 1995-EARLIER MODELS With a test light, probe the two black wires leading to each of the stock front turn signals. On each side, the wire that has power only when the turn signal button is depressed is the turn signal positive wire. The wire that is “hot” constantly when the key is on is the running light wire. Connect the violet wire from the Silver Bullet to the bikes turn signal wire, and the blue Silver Bullet wire to the bikes running light wire. Connect the black wire from the Silver Bullet to a known good chassis ground (bare metal). Insulate your connections. Route the wires neatly out of harms way and secure them with nylon cable ties. When replacing stock incandescent turn signals with LED lights, it may be necessary to add a load equalizer to make the turn signals flash properly. NOTE: When using Amber Dual Circuit Silver Bullets in rear applications, blue running lights (power) wire will not be used. To avoid corrosion, tape off bare wire. Test the lights for run and flash functions. If they light, but do not flash in the turn mode, add the load equalizer. The load equalizer has one black and two violet wires. The violet wires are not side specific. NOTE: LED Turn signals require the use of one Load Equalizer PER PAIR OF LED TURN SIGNALS to achieve the proper flash function. It is perfectly normal for the equalizer to get warm (about 140 degrees) during turn signal operation.

Incoming search terms:

Harley Davidson FL series Electra Glide, Ultra Classic, Road King, Road Glide Left and Right Mounting Plate Installation Installation Manual

0

Filed Under (Harley Davidson) by admin on 25-02-2012

download
Remove existing control arm end cap and grind the outside flush. See picture below for reference. The swing arm will drop if both sides are removed at the same time. To ease installation, complete one side before starting on the other. Note: there is a left and right. Left and right end caps shown. 2. Install mounting plate assembly 10002351 on top of the end cap using 7/16″ hex head bolt and lock washer in the bottom hole. Use the 7/16″ counter sink bolt in the top hole. Make sure the end cap is seated properly. The end cap notch should fit into the recess on the frame. The pivot arm assembly is shipped on mounting plate assembly; you may remove the pivot arm to make installation easier. 3. Snug up the bolts evenly, make sure the end caps are not crooked in relation to the frame. Tighten both bolts to 25 ft lbs. (Further tightening will be required after the toe in is set). 4. If you removed the left hand pivot arm assembly, remount it now, 10002575-A (pg 20) with seal, bearings (2), washer, nut, cotter pin and dust cover. 5. Repeat for right hand side. 5 Toe In Adjustment Adjustment made with the mounting plates, bolts, pivot arms, and hubs (without wheels and tires) in place

Incoming search terms:

HARLEY DAVIDSON ADVANCED AUDIO XM SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
this kit fits 2006 and later FLHT (Electra Glide®), FLHTC (Electra Glide Classic), FLHTCU (Ultra Classic® Electra Glide), FLHX (Street GlideTM) and FLTR (Road Glide®) model motor- cycles. XM satellite radio is available within the continental United States. It is not available in Alaska or Hawaii. Additional Parts Required FLHT models will require prior installation of an Advanced Audio AM/ FM/ CD Radio Kit (Part Number 76412-06) and an AM/ FM Antenna Kit (Part Number 76325-06 or 76317-06). Unless one has already been fitted as part of another Advanced Audio kit installation: FLHT, FLHTC, and FLHX models will require the additional purchase of a Non-Ultra Overlay Harness (Part Number 70169- 06) and a left-hand Antenna Bracket (Part Number 76456-06). FLHTCU models will require the additional purchase of an Ultra Overlay Harness (Part Number 70164-06) and a left-hand Antenna Bracket (Part Number 76456-06). FLTR models will require the additional purchase of a Non- Ultra Overlay Harness (Part Number 70169-06) and an Antenna Bracket (Part Number 76316-06). If two modules are already installed on top of the radio, two Dual-LockTM mounts, Part Number 76434-06, will be needed. These items are available from a Harley-Davidson Dealer INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. 2. Remove the outer fairing and windshield. Refer to OUTER FAIRING/ WINDSHIELD REMOVAL in the Service Manual. NOTE If another module has been installed in the location reserved for the XM radio module, relocate that module per the instructions supplied with that kit

Incoming search terms: