2003 honda shadow spirit 750 carburetor installation

You search Auto repair manual PDF 2003 honda shadow spirit 750 carburetor installation, if there are search results will appear below. If search results do not exist, please search by others keyword.





2003 Honda Shadow Spirit 750 VT 750DC Custom speedometer dial installation

0

Filed Under (Honda) by admin on 06-11-2011

download
DO NOT REMOVE THE 3 PHILLIP SCREWS ON THE BACK OF THE SPEEDOMETER. This will unscrew the circuit board and the main components inside the speedometer, and possibly damage it. Just leave those 3 screws alone. They won’t make your customization any easier if they are removed. This is the hard part. Turn the speedometer face down on a soft towel on a sturdy table, bench, etc. I used a regular flat screwdriver to do this step. There is a chrome metal ring holding the glass on the speedometer. It is factory sealed. On the bottom side of this ring start prying with a flat screwdriver under the bottom lip of the metal ring. This will be a slow process (patience, patience, patience) so don’t get in a hurry and ruin the wife’s kitchen table like I did. Go around the metal ring with a flat screwdriver prying it up as straight as you can. It’s easier doing this every millimeter or two. I had to do this about 3 times all the way around the ring. After you pry the lip of the ring up all the way around enough to loosen it up considerably, gently pull the ring off of the speedometer. The glass should come off with it. Put the glass with the chrome ring aside for later. You might want to use a soft lint free towel to rest it on

Incoming search terms:

HSR Carburetor Total Kits Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
Intake Manifold: 1. Install MAP sensor in Mikuni manifold (Twin Cam only). 2. Attach the Mikuni manifold to the engine. Align the manifold before tightening the bolts. The flange surface of the Mikuni manifold should be parallel with the front of the engine’s cam cover. Use a level or angle meter to check this. Tighten the manifold bolts. 3. Attach the rubber flange to the Mikuni manifold with the furnished 5/16″x3/4″ bolts and washers. Choke Cables: Mikuni & Harley-Davidson Route the cable with largest radius bends possible. Check the cable for free-play after installation. If there is no free-play, the engine may run rich and deliver poor performance or low fuel mileage. Harley Cable (Twin Cam Kits: 42-19, 45-4) : 1. Remove the Harley choke cable from the stock carb. 2. Remove the spring and plunger from the cable. 3. Remove the spring and plunger from the Mikuni. 5. Install the Mikuni spring and plunger onto the Harley choke cable. Change nothing else; be sure to use the Harley plastic nut, not the Mikuni nut (See Figure 1). Total Kit Installation Instructions The HSR series carburetors are precise yet durable instruments; however, like any other piece of fine equipment, they require correct installation and reasonable care to assure optimum performance and long life. Extra time spent during installation will pay off in both short and long term performance and reliability. This Mikuni HSR carburetor kit is designed to be a bolt-on application, and as such, is set-up and jetted properly for most applications. However, since Harley-Davidson motors are often highly modified, alternate tuning settings may be required. The Mikuni Tuning Manual helps make jetting alterations and adjustments an easy matter. NOTE: Carburetor Kits not designated as C.A.R.B. exempt, are not legal for motor vehicles operated on public highways in the state of California, or in any other states and countries where similar laws apply. WARNING NOTE: NOTE: WARNING CAUTION NOTE: NOTE: TK-2 6. Install the new assembly into the Mikuni carburetor. Be careful to only gently tighten the plastic nut. 7. Loosen the knurled plastic friction nut behind the choke knob and check for free-play (see Figure 2). Figure 1: Harley nut with Mikuni spring & plunger Figure 2: Choke cable adjustments Mikuni Cable (Evo Kits: 42-8, 45-2 & 45-3) : 1. Remove nut, spring and plunger from the Mikuni. 2. Install the nut, spring and plunger onto the cable. 3. Install the assembly into the Mikuni HSR carburetor. Be careful to only gently tighten the plastic nut. 4. Check for free-play. Adjust the cable as necessary. An optional choke cable mounting bracket is included in the Evo kits for custom installations. Carburetor Installation: 1. Insert the carb fully into the rubber flange, align with engine and tighten the clamp. 2. Slip the fuel hose onto the carburetor’s fuel fitting and secure with the enclosed hose clamp. NOTE: Some Twin Cam installations may require removal of a small amount of fin material from the cylinders to clear the float bowl. Throttle Cables The HSR carburetor uses stock 1990 and later Harley- Davidson cables. However, if your Harley is fitted with some other carburetor, you may need to purchase a set of cables. See your dealer for the correct cable set. 1. Route the throttle cables with large radius curves and so they do not interfere with other components. 2. Screw the cable adjusters together to make them as short as possible. 3. Connect the “close” cable first (see Figure 3). 4. Install the “open” cable next (see Figure 3). 5. Adjust the opening cable until the slide can be opened fully. Snug the adjuster lock nut. 6. Turn the handlebar to the right and adjust the throttle free-play with the closing cable adjuster to approximately 1/8″ (see Figure 4)

Incoming search terms:

HARLEY DAVIDSON BIG TWIN SPIGET MOUNT CARBURETOR INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 26-03-2012

download
A. BEFORE INSTALLATION OF YOUR NEW ZENITH CARBURETOR, NSPECT THE RUBBER MANIFOLD SEAL FOR NICKS,CRACKS, OR DEBRIS. APPLYING A LIGHT FILM OF PETROLEUM BASED LUBRICANT AROUND THE INSIDE LIP OF THE RUBBER SEAL WILL ALLOW THE CARBURETOR TO SLIP INTO PLACE EASIER. B. BEFORE ACTUAL INSTALLATION OF UNIT INTO MANIFOLD, THROTTLE CABLES SHOULD BE HOOKED TO THETHROTTLEWHEEL.MAKESURETHATTHE PULL CABLE IS LOCATEDPROPERLY TO OPEN THE THROTTLE PLATE (IN SOME APPLICATIONS THROTTLE CABLE SLACK MAY NEED TO BE ADJUSTED FOR PROPER HOOKUP AND OPERATION) SEE FIG. #1 C. AFTER THROTTLE CABLES ARE PROPERLY HOOKED UP,UNITCAN BE INSERTED INTO MANIFOLD. MAKE SURE THAT UNIT IS FULLY SEATED. WITH CARBURETOR SEATED INTO MANIFOLD AND FUEL LINE HOOKED UP TO FUEL INLET, INSTALL CHOKE CABLE AND HOOK TO CHOKE LEVER. PLACE AIR INTAKE GASKET ON END OF CARBURETOR, NEXT PLACE INTAKE ADAPTOR OVER INTAKE GASKET. SEE FIG#2 ZENITH MOD.16P12 SPIGET MOUNT CARBURETOR -HARLEY DAVIDSON ™ BIG TWIN INSTALLATION INSTRUCTIONS FIG. # 1 FIG. # 2 D. WITH ADAPTOR IN PLACE, LOCATE THE STOCK AIR BOX OVER THE ADAPTOR, UTILIZING THE STOCK AIR BOX GASKET (THERESHOULDBENO GAPS BETWEEN ADAPTOR, AIRBOX OR CARBURETOR WHEN PROPERLY INSTALLED) STAND-OFF SPACERS PROVIDED ARE TOBEPLACEDBETWEENAIR BOX& ENGINE HEADS BEFORE INSTALLING THE VENT/RETAINING BOLTS. FOR EVALUATION ENGINES STOCK VENT BOLTS CAN BE USED WITH LARGERI.D. SPACER PROVIDED. SEE FIG#3 E. WITH AIR BOXSECURELY IN PLACE, INSTALL THE AIR FILTER COVER RETAINING BRACKET AND FILTER USING THE STOCKBOLTS, AND REPLACE AIR FILTER COVER AND SECURE WITH STOCK BOLT. SEE FIG#4 F. AFTER INSTALLATION IS COMPLETE AND FUEL FLOW HAS BEEN RE-ESTABLISHED, CHECK FOR ANY LEAKS BEFORE STARTING ENGINE. H. AFTER STARTING ENGINE, SOME ADJUSTMENTS OF IDLE AND MAIN JET MAYBE REQUIRED FOR PROPER OPERATION. AFTER ADJUSTMENTS HAVE BEEN MADE AND WITH ENGINEAT IDLE, TURN WHEEL FULLYTOLEFTANDRIGHT.ANYCHANGEIN IDLE SPEED INDICATES THROTTLE CABLES ARE TOO TIGHT AND MORE SLACK MUST BE PROVIDED.

Incoming search terms:

HONDA ATV Carburetor Repair Kits Installation

0

Filed Under (Honda) by admin on 21-12-2011

download
ATV Carburetor Repair Kits Complete kits to rebuild one OEM carburetor. Each kit contains necessary gaskets/o-rings, needle valve or needle valve set, and jets. Made in Japan. Note: Check all parts before installation. Honda Model Year Order No AT C70 78-85 025-001 AT C90 70-71 025-003 ATC90K1/K2/K3 72-75 025-003 AT C90 76-78 025-003 TRX90 Fourtrax 90 93-98 025-084 ATC110 79-83 025-005 ATC110 84-85 025-061 ATC125M 84-85 025-062 TRX125 Fourtrax 85-86 025-050 TRX125 Fourtrax 87-88 025-063 ATC185 1980 025-009 ATC185S 81-83 025-009 AT C200 81-82 025-008 AT C200 1983 025-009 ATC200E Big Red 82-83 025-064 ATC200ES Big Red 1984 025-064 AT C200M 84-85 025-064 AT C200S 84-86 025-065 AT C200X 83-85 025-012 AT C200X 86-87 025-014 TRX200 Fourtrax 200 90-91 025-066 TRX200D Fourtrax 200 Type II 1991 025-066 TRX200D Fourtrax 200 Type II 92-93 025-067 TRX200D Fourtrax 200 Type II 94-97 025-068 TRX200SX Fourtrax 87-88 025-069 ATC250R 81-82 025-017 ATC250R 83-84 025-018 AT C250R 1985 025-019 ATC250ES Big Red 85-87 025-029 AT C250SX 1985 025-070 TRX250 Fourtrax 250 1985 025-071 TRX250 Fourtrax 250 86-87 025-072 TRX250EX Sportrax 250EX 01-04 025-085 TRX250R Fourtrax 250R 86-87 025-060 TRX250R Fourtrax 250R 1988 025-073 TRX250X 91-92 025-074 TRX300 Fourtrax 300 1988 025-075 TRX300 Fourtrax 300 91-92 025-076 TRX300 Fourtrax 300 93-95 025-078 Honda Model Year Order No TRX300EX Fourtrax 300EX 93-98 025-081 TRX300FW Fourtrax 300 4×4 1988 025-075 TRX300FW Fourtrax 300 4×4 91-92 025-076 TRX300FW Fourtrax 300 4×4 93-95 025-078 AT C350X 1985 025-035 TRX350 Fourtrax 4×4 86-87 025-079 TRX350FE Fourtrax Rancher 4×4 ES 00-03 025-082 TRX350FM Fourtrax Rancher 4×4 00-03 025-082 TRX350TE Fourtrax Rancher ES 00-03 025-082 TRX350TM Fourtrax Rancher 00-03 025-082 TRX350D Fourtrax Foreman 4×4 87-89 025-079 TRX400FW Fourtrax Foreman 95-00 025-080 TRX450ES Fourtrax Foreman ES 98-01 025-083 TRX450FE Fourtrax Foreman ES 02-03 025-083 TRX450FM Fourtrax Foreman S 02-03 025-083 TRX450S Fourtrax Foreman S 98-01 025-083 TRX500FAFourtrax Rubicon 01-04 025-086

Incoming search terms:

Honda CBR 954 RR Undertail Kit INSTALLATION

0

Filed Under (Honda) by admin on 04-12-2011

download
Carefully remove the tail section body work. Save all bolts, washers and plastic rivets for re-installation of tail. Disconnect and remove the brake light (with all mounting grommets and washers), license plate and turn signals, key lock (with clip) and move all wiring out of the cutting areas. Remove the two bolts at the rear end of the stock fender (inside glove box) to allow the end to hang down for cutting.
2) Using a “Dremel” tool or cutting disc (this can also be done using a sharp edged knife, but is not recommended), remove the plastic shown in the photos to the above and below. Be sure to take your time cutting, so that you don’t cut away any more plastic than necessary. Honda CBR954RR Undertail Kit (2002-03, Available in: Honda Red, Gloss Black and Gun Metal) 3) *Install license plate brackets to back side of license plate as shown. Now hold license plate in desired location on undertail, carefully mark and drill holes, install using the two (2) sets of allen bolts and lock nuts. 4) Insert undertail left side first, then right side, be carefully not to crack
or scratch undertail. Use your stock plastic screw rivets to hold under- tail in place. Tighten all hardware on tail section, attach seat.
5) Using clips, splice your turn signal wires to the signals in the undertail. On the bike; the orange wire is the the left turn, light blue wire is the right turn and the green wires are the grounds. On the undertail the red wires are the power wires and the black wires are the ground. * After this modification your undertail is not returnable. Paint is not warrantied against paint chips, flaking or scratches from installation or rocks being thrown from tire into the tray. Need Help? If you need additional help with the installation of the undertail, go to www.hotbodiesracing.com and look for the “FAQs” link at the bottom of the home page. Most of your general questions can be answered on those pages. This installation does require a basic mechani- cal aptitude, if in doubt, contact your local motorcycle shop and have a professional mechanic perform the installation, 3 hours is the average installation time

Incoming search terms:

The Honda Ace/ Spirit 750 Lowering Kit from INSTATALLATION

0

Filed Under (Honda) by admin on 16-11-2011

download
The installation of the Scootworks Ace/Spirit Lowering Kit follows the same procedure as replacing the rear shocks. However, Scootworks wanted to assist you as much as possible with the installation process, and developed this instruction package. If there are any steps you feel need improvement in instructions, please email support@scootworks.com and specify the area you are having trouble with. Unpacking! The shipping container and contents must be inspected by the purchaser for damage to goods immediately upon receipt of goods, and a claim must be filed with the carrier if damage is discovered. The purchaser must contact Scootworks within 24 hours from receipt of damaged goods to file a claim, and for further instructions. Your Scootworks Ace/Spirit Lowering Kit will come packed with a left and right side lowering assembly, two large flat washers, two M8 x 1.25 hex head bolts, and these printed instructions

Incoming search terms:

Honda CB 750 SOHC 8v Performance and Racing Camshafts Installation

0

Filed Under (Honda) by admin on 18-11-2011

download
Upon installation of your WEB-CAM camshaft, check the following. These operations are very important to engine
life, please follow instructions! If your cam is described as a bolt-in in the WEB-CAM catalog, you may skip 1-5
below. Check piston to valve clearance. Provide the necessary clearance by removing material from the piston Minimum .050″ intake, .080″ exhaust.1. Check valve to valve clearance. It may be necessary to remove material from the valves or sink valve seat height in head. 2. Check the valve spring retainer to valve guide clearance at maximum lift. Remove material from the top,of valve guides to provide a minimum of .030″ clearance. 3. Check for valve spring coil bind at maximum valve lift. Clearance at every coil should be at least .015″4. Be certain that cam and/or rocker arms rotate
freely in head or block. Remove material from head,block, or rocker arms where necessary.5. Engine and cam life depend on proper installation. New or reground followers should be used when installing WEB-CAM profiles. Apply the provided
assembly lube to cam lobe and follower surfaces

HOVELHEAD & IRONHEADXL 42mm Mikuni Carburetor And Manifold Kit INSTALLATION Instructions

0

Filed Under (Tips and Review) by admin on 31-10-2010

download
THROTTLE CABLE ADJUSTMENT A) Rotate the throttle grip to the full open position, look into the throttle bore and see if the throttle valve (slide) opens completely. If the throttle valve does not open completely unscrew the adjuster on the opening cable until it does. This adjustment should be made carefully to assure maximum carburetor performance. After adjustment tighten the adjuster jam nut. B) After adjusting the open cable, adjust throttle freeplay with the closing (idle) cable to approximately 1/8″ an indicated in the following illustration. note It is very important to adjust the cables in the preceding described manner to ensure that the idle cable operates correctly for safety. It must close the throttle completely 2 PLEASE NOTE USE CAUTION PLEASE NOTE SAFETY WARNING pull open cable pull close cable SHOVELHEAD/IRONHEAD XL Installation Instructions Check and make sure that the throttle cables are routed properly by rechecking the throttle play as the handlebars are turned from side-to-side; the amount play should remain consistent. C) After the throttle cables have been adjusted, make sure that all the lock nuts are securely tightened. 5. AIR CLEANER A) The air filter bracket is attached to the crankcase with 1 long bolt, and a bracket-spacer. Removed the crankcase nut located between the tappet blocks & replace it with the enclosed bracket spacer; tighten the spacer securely. B) Remove the stud protectors from the K&N filter and place the two backing plates on the studs. Now slip the the filter onto the carburetor. C) Attach the 2 long brackets to the air filter studs with the enclosed nuts & flat washers, and to the bracket spacer with the enclosed bolt using the lock washers, and flat washers. When the carburetor and air cleaner are properly aligned, securely tighten all of the mounting hardware including the intake manifold clamps. In some cases it may be necessary to bend the brackets slightly to arrive at the correct fit. D) Use the enclosed hose clamps to secure the fuel hose to the petcock, and the HSR carburetor. The screw clamp goes on the petcock end and the spring clamp attaches to the carburetor end. E) Attach the chrome air filter cover with the enclosed socket head screw. 7. CHOKE CABLE INSTALLATION A) Attach the Mikuni choke cable bracket to the original choke cable bracket on the air cleaner stud with the enclose hardware as illustrated

Incoming search terms:

HSR Carburetor Total Kits Installation And Tuning Manual

0

Filed Under (Tips and Review) by admin on 31-10-2010

download
1. Disconnect the battery ground wire from the battery. 2. Turn the fuel petcock to the “OFF” position. 3. Elevate the rear of the fuel tank for better access to the carburetor area. 4. Remove the coil, horn or other devices on the left hand side of the engine to allow free access to the intake manifold bolts. 5. Remove the complete air cleaner assembly, including the backing plate. 6. Disconnect any vacuum hoses and the fuel hose from the stock carburetor. 7. Disconnect the choke cable from the frame. 8. Remove the stock carburetor. 9. Evo: remove the stock manifold. 10. Twin Cam: unplug MAP sensor, remove manifold and then remove the MAP sensor from the manifold. Installation: Intake Manifold: Twin Cam only: Install MAP sensor in Mikuni manifold. 1. Attach the Mikuni manifold to the engine. Align the manifold before tightening the bolts. The flange surface of the Mikuni manifold should be parallel with the front of the engine’s cam cover. Use a level or angle meter to check this. Tighten the manifold bolts. 2. Attach the rubber flange to the Mikuni manifold with the 5/16″x3/4″ bolts and washers. To ease installation, use liqiud detergent to lubricate the manifold seals. Choke: Evo: We recommend that you use the Mikuni choke cable that is furnished with the carburetor. However, you can use the stock Harley cable (’90-’99 models only) if you follow the Twin Cam choke cable instructions. Twin Cam: 1. Remove the Harley choke cable from the stock carb. 2. Remove the Harley spring and plunger from the Harley choke cable. 3. Remove the Mikuni spring and plunger from the Mikuni carburetor. 5. Install the Mikuni spring and plunger onto the Harley choke cable. Change nothing else; be sure to use the Harley plastic nut, not the Mikuni nut. 6. Install the new assembly into the Mikuni. Be careful to only gently tighten the plastic nut.

Honda Shadow Backrest Kit Installation Manual

0

Filed Under (Honda) by admin on 07-12-2011

download
Install the right and left brackets, leave screws loose to allow brackets some movement for ease of backrest installation. Install the ackrest as shown, if optional carrier is also purchased, use the longer flange bolts provided. Note the backrest goes inside of the brackets, and carrier rack (optional) will go outside of the brackets when installed. Tighten all nuts and bolts to the torques specified

Incoming search terms: