2003 indian scout motorcycle belt guard

You search Auto repair manual PDF 2003 indian scout motorcycle belt guard, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2003 indian scout motorcycle belt guard Direct Download speed 5282 Kb/s

  2003 indian scout motorcycle belt guard Full Version speed 6162 Kb/s



HARLEY DAVIDSON SOFTAIL CHROME LOWER BELT GUARD INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-04-2011

download
REMOVING STOCK PLASTIC LOWER BELT GUARD 1. See Figure 1. Remove the hex head bolt (2), washer (3), acorn nut (5), hex head screw (4) and acorn bolt (8) attaching plastic belt guard to rear fork. 2. Remove the plastic belt guard. Save fasteners (2), and (4), washer (3), acorn nut (5) and acorn bolt (8) for installing new chrome belt guard. INSTALLING CHROME LOWER BELT GUARD 1. See Figure 2. Position the new chrome belt guard from kit over belt. Align the holes in guard with mounting lugs on rear fork. Install acorn bolt (9) through mounting lug and fasten to belt guard. Finger tighten only. 2. Install screw (4) with washer (5, from kit) through belt guard and fasten to threaded mounting lug. Position the guard for adequate clearance and finger tighten screw. 3. At the upper belt guard, install the original forward hex bolt (2) and original washer (3) through the upper guard (1), then through the upper hole in chrome belt guard and through mounting lug on rear fork. Secure with original acorn nut. 4. Tighten all hardware to 110 in-lbs (12.4 Nm)

Incoming search terms:

HARLEY DAVIDSON CHROME UPPER BELT GUARD KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION NOTE When performing the following step, it is not necessary to completely remove the shock mount bolt, back the bolt out only until it is flush with the swingarm. 1. See Figure 1. Loosen the left rear shock mount bolt (1) and back it out until the threaded portion of the bolt is flush with the swingarm. 1 2 is03762 1. Shock mounting bolt (left side) 2. Belt guard Figure 1. Loosen Shock Mounting Bolt 2. Pull the belt guard (2) straight back toward the rear of the bike to remove the guard from upper and lower grommets. See Figure 2. It may be necessary to work the guard up and down slightly to dislodge it from the upper (1) and lower (2) grommets. Remove the belt guard and discard. 2 1 3 is03763 1. Upper grommet mount 2. Lower grommet mount 3. Front belt cover Figure 2. Rubber Grommet Mount Locations 3. Obtain the chrome belt guard from kit. While making sure belt guard is over the belt, slide the guard straight in between the shock and sprocket and align cover just below front belt cover (3). The cutouts in the bracket should be lined up to engage with upper and lower grommets. NOTE When performing the following step, gently pull the guard in and out at the center; it should feel fairly tight even though the rear mounting bracket has not been secured. 4. See Figure 3. Firmly push the guard toward the front of the bike until the cutouts are secured by the grommets and the belt guard mounting bracket (1) hole lines up with the shock bolt

Incoming search terms:

Harley-Davidson EMERGENCY DRIVE BELT REPLACEMENT KIT Installation Manual

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
1. Shift transmission to neutral. Before installation of the emergency belt, to avoid personal injury and/or vehicle damage, secure the motorcycle. Both stand and motorcycle must be on solid, level ground. Failure to follow instructions could result in death or serious injury. 2. See Figure 1. Remove spring clip (4) (if present) and loosen rear axle nut (1). 3. Loosen rear axle adjuster (3) (or adjuster nut, if so equipped) on each side of motorcycle, and move rear wheel to full forward position. 4. Remove the damaged/broken belt. 5. Inspect sprockets and belt guard (2) for damage and/or debris. Remove any debris. If sprockets and belt guard are not damaged, proceed with the installation. 6. Remove belt guard. 40171-97,40146-00 1 WARNING i06186 Figure 1. Axle 1. Axle nut 2. Belt guard 3. Adjuster 4. Spring clip 2 4 1 3 7. See Figure 2. Install feeder strip on emergency belt. 8. Feed strip around transmission sprocket in a counterclockwise direction over frame cross support. 9. See Figure 3. Interlock the “v” ends of the emergency belt. a. Insert a hex socket key in the fourth (4) and ninth (6) tooth holes. b. Place the splice block (2) over the seventh (5) tooth hole. c. Install a socket head set screw (3) in the seventh tooth. Tighten using another hex socket key. d. Move the block to the next tooth, and repeat installation steps (b) and (c) in each tooth until all 12 screws are installed. NOTE There are 16 screws included in this kit. However, only 12 screws will actually be installed in the belt. The remaining four screws are spares. 10. See Figure 4. Grasp the emergency belt at the mid point of the lower run between your thumb and forefinger and lift the belt up to take up any slack in the belt. Measure the distance that the belt deflects (2) under tension (1). When two pounds of tension is applied to the lower run of the emergency belt, the belt deflection should be within the following measurements

Incoming search terms:

HARLEY DAVIDSON SADDLEBAG GUARD RAIL KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
Installation NOTE A Service Manual for your vehicle is available from your Harley-Davidson Dealer. 1. Remove saddlebags from motorcycle according to Service Manual instructions. 2. Remove left and right side covers (located just ahead of saddlebags) by removing Phillips head screw from bottom of side cover. Save hardware and side covers for later reassembly. 3. Remove upper and lower bolts securing left and right forward saddlebag guards to frame. Remove Phillips head screws securing saddlebag guards to muffler supports. Discard saddlebag guards, but save hardware. 4. See Figure 1. Install new left and right forward saddlebag guards (1) with upper bolts (2), lower bolts (3) and Phillips head screw (4) saved from Step 3. 5. Insert one rear guard rail mount (6) onto rounded, tubular end of one of the saddlebag side guard rails (5). 6. Insert a hex cap screw (8) through one of the front guard rail mounts (7) as shown. 7. Line up saddlebag side guard rail (5) with attached rear guard rail mount (6) from Step 5 with lower hole in forward saddlebag guard rail (1). Insert hex cap screw (8) from front guard rail mount (7) through hole in forward guard rail (1) and into side guard rail assembly. Tighten finger tight. 8. See Figure 2. Install a side guard rail (2) in lower position on rear fender support (3) with pan head screw (1). Tighten finger tight. 9. Repeat Steps 5 through 8 in upper position. 10. Repeat Steps 5 through 9 for opposite side of vehicle. NOTE Each of the four guard rail clamps vary slightly. Two fit together for the right side of the motorcycle and two fit together for the left side. The inner right and left clamps have two holes drilled through them. 11. See Figure 2. Locate four guard rail clamps (4). Match up two left side and two right side guard rail clamps. Install one piece of cushion tape to the lower inner surface of right and left inner clamps. Peel off paper from outer surface of tape. Do not apply tape to the outside clamps. NOTE Be sure that you correctly position the inner clamps on the side guard rails, as directed in Step 12, before tape on inner clamp contacts side guard rails. Tape is very sticky and will be difficult or impossible to remove once it has made contact with side guard rail surface. 12. See Figure 2. Position clamps (4) in desired position on side guard rails (2). Install clamps (4) on left and right side of vehicle side guard rails using four Torx screws (5). Torx screw heads should face inward toward motorcycle. Tighten each screw a little at a time until secure. 13. Tighten hex cap screws and pan head screws installed in Steps 7 and 8.

Incoming search terms:

HARLEY DAVIDSON CHROME LOWER BELT GUARD INSTALLATION INTSRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Owner’s Manual and follow the instructions given to remove the Maxi┬« Fuse. 2. See Figure 1. Remove the three screws with captive washers (3) securing the original equipment (O.E.) lower belt guard (debris deflector, Item 1) to the underside of the rear fork (2), and set them aside for re-use. Remove and discard the lower belt guard. 3. Position the new chrome lower belt guard in place on the underside of the rear fork, lining up the three holes in the belt guard with the mounting holes in the fork. Insert the three screws saved earlier through the holes in the belt guard, and thread them into the fork. Tighten the screws to 36-60 in-lbs (4.1-6.8 Nm) . 4. Verify that the Ignition/Light Key Switch is turned to the OFF position. Refer to the Owner’s Manual and follow the instructions given to re-install the Maxi┬« Fuse. 2 1 3 is04766 1. Lower belt guard (debris deflector) 2. Rear fork (swingarm) 3. Screw with washer (3) Figure 1. Lower Belt Guard Installation

Yamaha V-Star 650 Engine Guard Installation Manual

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Protect the rear portion of the front fender with a towel or other thick, soft cloth. Remove the OEM engine guards if they have been installed on the motorcycle. Your new Barons engine guard will fasten to the frame at the same points as the OEM guard and will use the same hardware. 2. Or, if OEM engine guards are not present, remove the 14mm bolts from the underside of the drivers footpeg mounts. 3. Remove the 12mm upper engine mount bolts located on both sides of the frame. Replacement bolts are included with your new engine guard. 4. Position the engine guard so that the lower brackets point towards the rear of the motorcycle, and slide the engine guard into the space between the front wheel and the frame. 5. Raise the guard until the holes in the lower mounting brackets align with the vacated bolt holes beneath the drivers footpegs. Due to production line tolerances in both the motorcycle and the engine guard, the mounting brackets may be too wide or too narrow for the frame. If this is the case, remove the guard from the motorcycle. Place the guard on a flat, firm surface. Insert a towel or other protective material between the guard and the surface. Using a rubber mallet or a block of wood and a hammer, tap the lower brackets until they are correctly spaced. 6. Insert the large washers (supplied with the guard) between the rear face of the lower bracket and the frame. The washer fills the space between the lower mounting bracket and the footpeg mount. Reinsert the 14mm bolts and finger tighten. 7. Rotate the guard until the holes in the upper mounting brackets align with the empty holes on each side of the frame. 8. Insert the replacement 13mm bolts, along with their washers, and tighten securely. Tighten all other nuts and bolts securely. 9. Remove the protection on the front fender and you’re ready to ride. CAUTION!!! You must re-tighten all four of the engine guard mounting bolts after 100 miles of riding! Care & Cleaning: Engine guards take the full brunt of the worst of what the weather in your area has to offer, making it critical that proper and complete cleaning take place on a weekly basis, or corrosion will occur which is not covered by warranty! Proper cleaning procedure would be to use a product like Simple Green, LOC, Salt-Away or similar. Mix a strong batch and apply it liberally with a soft towel or soft nylon brush to the entire

Incoming search terms:

Yamaha Road Star Engine Guard Installation Manual

0

Filed Under (Yamaha) by admin on 07-11-2010

download
1. Protect the rear portion of the front fender with a towel or other thick, soft cloth. 2. Remove the OEM engine guards if they have been installed on the motorcycle. Or, if OEM engine guards are not present, Remove the two lower engine mount bolts. These bolts are located on the inside of the right and left frame rails, and will be replaced with the longer 10mm bolts included with your new engine guard. 3. Position the engine guard so that the lower brackets point towards the rear of the motorcycle, and slide the engine guard into the space between the front wheel and the frame. 4. Raise the guard until the upper V” mount is located between the frame rails. Note: Your new Barons engine guard is equipped with a unique upper V” mount clamp. This clamp becomes a cradle for the upper frame supports when it is inserted between the frame rails. 5. Rotate the engine guard until the lower mounting brackets are aligned with the lower engine mount holes. Due to production line tolerances in both the motorcycle and the engine guard, the mounting brackets may be too wide or too narrow for the frame. If this is the case, remove the guard from the motorcycle. Place the guard on a flat, firm surface. Insert a towel or other protective material between the guard and the surface. Using a rubber mallet or a block of wood and a hammer, tap the lower brackets until they are correctly spaced. 6. Insert the new 10mm bolts and washers, and finger tighten only. 7. Tighten each 3/8″ bolt in the upper clamp evenly by using a 9/16″ socket or a wrench. Snug down each bolt until it draws the front of the upper clamp into contact with the upper frame supports, then adjust these bolts accordingly to achieve equal spacing between each floorboard and the lower engine guard rail. 8. Tighten the jam nuts against the washers to lock each bolt in place. CAUTION! It is critical that you do not over-tighten these bolts. Tighten all remaining nuts and bolts securely. If necessary, slightly loosen rear brake line banjo bolt and rotate banjo fitting for clearance with engine guard. Tighten banjo bolt and check brake for proper operation. You must re-tighten all four of the engine guard mounting bolts after 100 miles of riding! Care & Cleaning: Engine guards take the full brunt of the worst of what the weather in your area has to offer, making it critical that proper and complete cleaning take place on a weekly basis, or corrosion will occur which is not covered by warranty! Proper cleaning procedure would be to use a product like Simple Green, LOC, Salt-Away or similar. Mix a strong batch and apply it liberally with a soft towel or soft nylon brush to the entire

Incoming search terms:

Yamaha V-Star 650 Engine Guard REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 03-01-2012

download
Protect the rear portion of the front fender with a towel or other thick, soft cloth. Remove the OEM engine guards if they have been installed on the motorcycle. Your new Barons engine guard will fasten to the frame at the same points as the OEM guard and will use the same hardware. 2. Or, if OEM engine guards are not present, remove the 14mm bolts from the underside of the drivers footpeg mounts. 3. Remove the 12mm upper engine mount bolts located on both sides of the frame. Replacement bolts are included with your new engine guard. 4. Position the engine guard so that the lower brackets point towards the rear of the motorcycle, and slide the engine guard into the space between the front wheel and the frame. 5. Raise the guard until the holes in the lower mounting brackets align with the vacated bolt holes beneath the drivers footpegs. Due to production line tolerances in both the motorcycle and the engine guard, the mounting brackets may be too wide or too narrow for the frame. If this is the case, remove the guard from the motorcycle. Place the guard on a flat, firm surface. Insert a towel or other protective material between the guard and the surface. Using a rubber mallet or a block of wood and a hammer, tap the lower brackets until they are correctly spaced. 6. Insert the large washers (supplied with the guard) between the rear face of the lower bracket and the frame. The washer fills the space between the lower mounting bracket and the footpeg mount. Reinsert the 14mm bolts and finger tighten. 7. Rotate the guard until the holes in the upper mounting brackets align with the empty holes on each side of the frame. 8. Insert the replacement 13mm bolts, along with their washers, and tighten securely. Tighten all other nuts and bolts securely. 9. Remove the protection on the front fender and you’re ready to ride. CAUTION!!! You must re-tighten all four of the engine guard mounting bolts after 100 miles of riding! Care & Cleaning: Engine guards take the full brunt of the worst of what the weather in your area has to offer, making it critical that proper and complete cleaning take place on a weekly basis, or corrosion will occur which is not covered by warranty! Proper cleaning procedure would be to use a product like Simple Green, LOC, Salt-Away or similar. Mix a strong batch and apply it liberally with a soft towel or soft nylon brush to the entire

Incoming search terms:

BMW R850, R1100, R1150, R1200 Oilhead Maintenance Manual

0

Filed Under (BMW) by admin on 16-11-2010

download
cold Engine and Drivetrain Procedures Check Alternator Belt Tools Parts T-handle hex – 4mm none Note: In most cases the alternator belt does not need to be checked any more. Early models should have the pulley and belt upgrade that came out a few years ago. Current recommendations are that the belt is installed and adjusted, then not disturbed until 36K when replacement is specified. 1. Remove the four bolts holding the black plastic alternator belt cover at the front of the engine, 4mm T-handle hex. 2. Remove the cover by sliding it straight down. 3. Check the belt for cracks or shredding. 4. Check the belt tension, quite tight, ~1/4″ deflection when you press on the center. Note: Paul Glaves suggests that proper belt tension is when you can twist the belt ~90 degrees, midway between the pulleys. If you can twist it more than 90 degrees, it is too loose. If you cannot twist it 90 degrees, then it is too tight. 5. Leave the cover off for the valve adjustment procedure on the next page. Change Alternator Belt Tools Parts T-handle hex – 4mm alternator belt socket – 13mm ratchet wrench – 13mm torque wrench 1. Remove the four bolts holding the black plastic alternator belt cover at the front of the engine, 4mm T-handle hex. 2. Remove the cover by sliding it straight down. 3. Loosen the 2 nuts and 1 bolt, 13mm, that hold the alternator – one is on top and one is on each side, thus allowing the alternator to pivot down. 4. Remove the old belt. (Some bikes have a pipe that traps the belt – loosen it enough to get the old belt out and the new belt in) 5. Install the new belt being sure it is properly seated. 6. BMW calls for a tensioning torque of 5.9 ft.lb. (8 Nm) on the adjuster bolt on the left side of the bike. You have to get at this bolt from the alternator side and you may have to lift the tank. Alternatively, you can pry the alternator up with a large screwdriver to tension the belt. 7. Once the belt is under proper tension, tighten the 2 nuts and 1 bolt, 13mm, to 15 ft.lb. (20 Nm). 8. Check the belt for proper tension (see above) and proper seating alignment

Incoming search terms:

HARLEY DAVIDSON BLACK ENGINE GUARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL NOTE This Instruction Sheet covers several different Harley-Davidson models and years. Be sure to locate and follow the procedures that apply to the motorcycle receiving the new guard. For Models without Lower Fairings 1. Proceed to For All Models section. For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Remove the lower fairings following the instructions in the appropriate Service Manual. 2. When the lower fairings have been removed, proceed to For All Models section. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley-Davidson Genuine Motor Accessory Lower Fairings 1. See Figure 1. Remove the two black screws (1) that attach the fairing cap (2) to the lower fairing (5). Remove the cap. Set the parts aside for re-installation. 2. Remove the screw (7), rubber washer (8) and locknut (10) and the clamp (9) that attaches the bottom of the lower fairing to the engine guard and set aside. 3. Remove the two locknuts (3), U-bolt (6) and U-bolt retainer (4). 4. Remove the lower fairing by sliding it out from behind the engine guard. 5. Repeat Steps 1 through 4 for the opposite side. 6. Proceed to For All Models section. For Model FLTR/I (Road Glide) with Harley-Davidson Genuine Motor Accessory Lower Fairings Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery, negative (-) battery cable first, following the instructions in the appropriate Service Manual. 2. Remove the seat following the instructions in the appropriate Service Manual. 3. Remove the cable strap holding the clutch cable to the engine guard. 4. See Figure 2. Remove the TORX screw (8), rubber washer (9) and locknut (11) and the clamp (10) that attaches the bottom of the lower fairing (4) to the engine guard and set aside INSTALLATION 1. Hold the engine guard in position, and loosely fasten the top of the guard with the new hex socket screw and flat washer from the kit. 2. Install the bottom brackets to the motorcycle frame with the two new TORX screws and locknuts. 3. Tighten all three screws to 15-20 ft-lbs (20.3-27.1 Nm) . For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Install the lower fairings following the instructions in the appropriate Service Manual. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley- Davidson Genuine Motor Accessory Lower Fairings 1. Carefully place one lower fairing in position from behind the engine guard. 2. See Figure 1. Install the lower fairing to the top of the new engine guard with the U-bolt (6) from the back, through the holes at the top of the fairing. Install the retainer (4) in position on the U-bolt and secure to the engine guard with the two locknuts (3). Do not tighten the locknuts at this time. 3. Attach the bottom of the fairing to the engine guard with the clamp (9) removed earlier. Install the clamp around the engine guard in the direction shown, with the tabs toward the rear of the vehicle and the flat side of the clamp against the lower fairing. Insert the screw (7) through the lower fairing, rubber washer (8) and clamp (9). Secure the assembly with the locknut (10). Tighten to 12 ft-lbs (16.3 Nm) .

Incoming search terms:

Incoming search terms: