2003 ttr 125 timing check

You search Auto repair manual PDF 2003 ttr 125 timing check, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2003 ttr 125 timing check Direct Download speed 5282 Kb/s

  2003 ttr 125 timing check Full Version speed 6162 Kb/s



Lambretta UNO50 Owners Manual

0

Filed Under (Lambretta) by admin on 25-11-2010

download
brakes: Inspect brake cables/hoses/linkage for correct mounting, chafing, leaks and damage. Check and adjust both front and rear brakes. If hydraulic, check fluid level and correct if necessary (DOT 4 fluid only). Engine: Check and correct the engine oil level. Fuel system: Check fuel tank, carburetor, fuel valve and all hoses for leaks. Throttle system: Check for correct throttle cable routing. Throttle operates smoothly and self-returns to idle from all handlebar positions. Wheels/tires: Check wheels, tires and valve stem for damage, etc. Check and adjust tire pressures. 11 Suspension: Check for smooth suspension operation. Lubricate all grease points using correct specification grease. Check for correct suspension adjustments. Inspect fork and shock seals for leaks. Steering: Check for smooth steering operation and handlebar bearings for proper adjustments. Electrical Systems: Check for correct function of all side, headlight (high/low beam) and taillights, turn indicators, brake lights, warning lights and instrument illumination. Check for correct horn operation. Check harnesses for correct routing. Check for correct function of starter lockout system. Check for correct engine stop switch operation. Check for correct function of the low oil warning light. (2 stroke only) Emission Systems: Check connections and hoses for routing and kinks.
12 Fastening hardware: Check front and rear axle nut and bolt torque. Check torque of drain plug and oil filter bolt. Check torque of all brake system nuts and bolts. Check torque of all steering system mounting hardware. Check torque of exhaust mounting hardware. Check torque of all remaining nuts, bolts & screws. Road test Front and rear brake operation. (approx. 10km): Check cold engine start performance. Evaluate performance, handling and braking. After road testing: Check hot engine starting. Check and adjust idle speed. Check for oil and fuel leaks. Make necessary adjustments and repair any defects seen or observed before, during and after test drive. Retest as necessary. Clean the vehicle prior to deliver

Incoming search terms:

POLINI X1 GENERAL INFORMATION AND SPECIFICATIONS

0

Filed Under (Polini) by admin on 02-12-2010

download
Air cleaner – Clean and reoil daily or after each moto to prevent motor failure and reduced performance. Transmission oil – change after every race, or at end of riding day. Chain – check tension and lubricate before every ride, adjust or replace as needed. Reoil after riding in damp conditions. Clutch – disassemble and clean clutch assembly frequently, every 2-3 races at least. Inspect kickstarter gears at this time. Ignition cover – remove cover and wipe dry after each ride or after washing bike to remove condensation. Piston rings – replace as often as every 3-5 races with expert rider, less often with less aggressive riders. Piston, pin, rod bearing & circlips – replace as often as every 8-10 races with expert rider, less often with less aggressive riders. Coolant – change yearly, make sure there is at least a 50/50 mixture of antifreeze if freezing temperatures are possible. Steering bearings – Check daily for looseness or play. Adjust and regrease as needed. Swingarm – Check often for looseness. Regrease several times a year. Replace bushings if any play is evident. Sprockets – check for worn or curved teeth each time chain is adjusted. Chain roller& wear pads – check roller for free rotation when checking chain. Make sure roller is not bent or damaged. Check chain wear strips on swingarm and chain guide frequently. Replace as needed to prevent chain from damaging motorcycle. Spokes – Check after each race or after each day of riding for looseness or damage. Wheels & tires – check wheels after each race for dents, cracks or other damage. Check tires for cuts, damage or wear. Check tire pressure daily and adjust for riding conditions. Shock – Check shaft area daily for signs of oil leakage or damage. Check swingarm and shock bushings for looseness. Forks – Check forks daily for leaking oil or damage to tubes. Make sure forks are not twisted check for smooth operation. Spark plug – check sparkplug color and condition after each race or end of riding day. Adjust jetting to keep plug from fouling or overheating. Silencer – If bike seems to be getting louder, replace packing and decarbonize inner tube. Expansion pipe – check daily for large dents, damage or leakage. Remove carbon from headpipe when pipe is removed. Have large dents fixed, or any dents within 8″ of the cylinder. Replace o-rings on pipe as needed to maintain a good seal. Footpegs – check daily for proper operation, pegs should spring back into place. Make sure pegs are not bent or overly dull. Handlebars – check bars after any crash for bending. Look for cracks near bar clamps. Replace bars that have been straightened more than 2 or three times, or if bar is badly bent. Aweakened bar can snap suddenly causing injury to rider. Throttle – check throttle for proper operation each time before bike is started. Remove and clean inside of grip and bar as needed. Grips – check grips daily for wear or looseness. Replace as needed. Use grip glue & safety wire to help hold grips in position. Calipers & pads – check pad wear and caliper function daily or after each race. Replace pads and clean calipers as needed. Brake lever – check lever daily for damage or wear. Make sure lever is at proper angle for both seated and standing positions. Leave lever clamp loose enough to allow clamp to rotate during crash rather than breaking lever. Check and adjust freeplay as needed. Brake pedal – Check pedal daily for damage and proper freeplay. Adjust rear caliper as needed. Reeds – Remove and inspect reed block during every ring change. Check reeds for signs of wear, fraying and cracking. Make sure reeds sit flat and seal well. Replace at any sign of wear or damage or at least once a year, more often for expert riders. Nuts & bolts – Check all nuts and bolts regularly. Make sure to check engine mounting bolts and swingarm bolt frequently

Incoming search terms:

2003 – 2004 4Runner & Tundra, 2004 Camry, Highlander, Sienna & SolaraREPAIR MANUAL SUPPLEMENT LEV II EVAP SYSTEM CHECK

0

Filed Under (Toyota Manuals) by admin on 24-10-2011

download
this TSB provides detailed instructions for a new LEV II EVAP System Check function using the Diagnostic Tester. The LEV II System Check allows the Diagnostic Tester to display the fuel tank vapor pressure as the EVAP VSV and the CCV are operated in a specific six-step pattern. Problems with the EVAP system are quickly isolated by observing the change in vapor pressure during each step. Once the vehicle condition is corrected, the LEV II System Check can also be used to confirm the repair before the vehicle is returned to the customer. The inspection procedure using the LEV II System Check (LEV II SYS CHECK) is described in this bulletin. This function is available using a Diagnostic Tester with version 11.0a software (or newer

HONDA CT110 OWNERS MANUAL

0

Filed Under (Honda) by admin on 22-04-2011

download
ENGINE OIL Engine Oil Level Check Check the engine oil level each day before riding the motorcycle. The level must be maintained between the upper (2) and lower (3) marks on the dipstick (1). 1. Start the engine and let it idle for a few minutes. 2. Stop the engine and hold the motorcycle in an upright position on firm, level ground. 3. After a few minutes, remove the oil filler cap/dipstick, wipe it clean, and reinsert the dipstick without screwing it in. The oil level should be between the upper and lower marks on the dipstick. 4. If required, add the specified oil up to the upper level mark. Do not overfill. 5. Reinstall the oil filler cap/dipstick, check for oil leaks. CAUTION Running the engine with insufficient oil can cause serious engine damage. TYRES Proper air pressure will provide maximum stability, riding comfort and tire life. Check tire pressure frequently and adjust if necessary. NOTE Tire pressure should be checked before you ride while the tyres are cold. Select the right replacement tire in accordance with the following specifications: Cold tire pressures kPa ( kg/cm2, psi ) Front: 175 ( 1.75, 25 ) Rear : 225 ( 2.25, 33 ) Tire size Front: 2.75 – 17 41P Rear : 2.75 – 17 41P Check the tires for cuts, embedded nails, ore other sharp objects. See your authorized Honda Dealer for replacement of damaged tires or punctured inner tubes OPERATION PRE-RIDE INSPECTION WARNING If the Pre-ride Inspection is not performed, serious damage or an accident may result. Inspect your motorcycle very day before you ride it. The items listed here will only take a few minutes to check, and in the long run they can save time, expense and possibly you life. 1. Engine oil level – add engine oil if required. Check for leaks. 2. Fuel level – fill the fuel tank when necessary. Check for leaks. 3. Brakes – check operation. Adjust free play if necessary. 4. Tyres – check condition and pressure. 5. Drive chain – check condition and slack. Adjust and lubricate if necessary. 6. Throttle – check for smooth opening and full closing in all steering positions. 7. Lights – check that headlight, tail/brake light, turn signals, indicators. 8. Engine stop switch – check for proper function. 9. Battery electrolyte – check the level and add if necessary Correct any discrepancy before you ride. Contact your authorized Honda dealer for assistance if you cannot correct the proble

Incoming search terms:

BMW F 650 GS Repair Manual And Maintenance schedule

0

Filed Under (BMW) by admin on 19-11-2010

download
Replace oil in telescopic forks Check the coolant and restore to correct level if necessary *) Replace the coolant (every 2 years) every 2years Check valve clearances, adjust if necessary Replace the spark plug Drain the outlet hose from the air filter box Replace intake air filter If motorcycle is operated in very dirty or dusty conditions, clean or replace the intake air filter every 10,000 km (6,000 miles); check every 3,000 km (1,800 miles) Replace fuel filter (every 20,000 km/12,000 miles) 20,000 km Check clutch play, adjust if necessary Check wheel spoke tension and tighten if necessary more frequently if motorcycle is ridden in severe off-road conditions Examine brake pads and discs for wear, replace if necessary *) more frequently if motorcycle is ridden in severe off-road conditions Check brake fluid level at front and rear and top up if necessary *) Check for operation of brake system and freedom from leaks; repair/replace if necessary *) Replace the brake fluid at least once a year Replace the primary front/rear brake master cylinder cup (every 40,000 km/24,000 miles on a motorcycle with ABS ) 40,000 km Check wheel bearings and replace if necessary *) Check or, if necessary, replace chain, sprocket, chain guide rollers and pinion *) more frequently if motorcycle is ridden in severe off-road conditions Check chain tension and adjust if necessary *) Check battery acid level, add distilled water if necessary more frequently if motorcycle is ridden in severe off-road conditions Clean and grease the battery terminals, if necessary Check steering head bearings and adjust *) or replace if necessary *) Grease the side and main stands Grease the brake pedal Check bolts and nuts on engine mountings, frame connections, exhaust system mountings, swinging fork pivot, suspension levers, brake pedal, main and side stands and quick-release axles for tightness Final inspection with road safety and functional check

YAMAHA TTR 125 SHOCKS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 08-01-2012

download
1. With the bike unloaded on the side stand and the shock fully extended, have an assistant measure from a point at the axle (center point) to a point on the frame, fender or bodywork directly above it. Record this measurement. 2. With the bike off the stand and the rider in the seat, bounce on the suspension and let the bike settle. Have the assistant measure from the same two points. Subtract the second measurement from the first. 3. The amount of settle, or “sag” is a function of the wheel travel. It should only be between 1/4 and 1/3 of the total travel. 4. If the difference is less than the minimum, reduce the spring preload. Measure the distance again starting with Step 2. Adjust again if necessary. 5. If the difference is more than the maximum, increase the spring preload. Measure the distance again starting with Step 2. Adjust again if necessary. Note: If the ride height is too low, the shock will bottom unnecessarily, resulting in a harsh ride. If the ride height is too high, the shock will “top out” too easily when rebounding from a bump or under hard deceleration. NITROGEN PRESSURES IN EMULSION SHOCKS CAUTION: The pressure in these shocks cannot successfully be checked. Concerns with the gauge volume and the gas volume in the shock body create a situation where you cannot accurately determine what pressure was in the shock. In addition when the pressure is lowered (i.e. checking the pressure) the gas and some of the shock oil escapes into the gauge. It is possible to lose a large percentage of the shock oil by depressing the core of a charged shock to the atmosphere. Please note that in order to check the pressure, some of the gas must escape and fill the gauge assembly. The volume of the gas pocket is about half the size of your thumb, so a very small volume change results in a large pressure drop. Because the gauges’ volumes vary, it is not possible to deduce the actual pressure in the shock prior to attaching the gauge. Therefore it is imperative that any attempt to check pressure be accompanied by the capability of refilling the shock. In other words: If you don’t have a nitrogen source handy, don’t check the pressure

Incoming search terms:

2003 – 2007 4Runner OIL LEAK FROM FRONT TIMING COVER

0

Filed Under (Toyota Manuals) by admin on 31-10-2011

download
evidence of a small oil leak located where the Bank 1 cylinder head, engine block, and timing cover meet. Use the following repair procedure to address this condition. 2003 – 2007 model year 4Runner vehicles equipped with the 1GR-FE engine and produced BEFORE the Production Change Effective VINs shown below. MODEL PLANT DRIVETRAIN PRODUCTION CHANGE EFFECTIVE VIN 2WD JTEZU17R#68064608 Hino 2WD JTEZU14R#78076191 4Runner Hino 4WD JTEBU14R#78078323 4Runner 4WD JTEBU14R#78090468 Tahara 2WD JTEZU14R#70091230 Tahara 4WD JTEBU14R#70117349 OP CODE DESCRIPTION TIME OFP T1 T2 EG7036 Reseal FrontTiming Cover with FIPG 2WD7.6 113100P0306548 EG7036 Reseal Front Timing Cover with FIPG 4WD8.5 11310-0P030 65 48 Applicable Warranty*: This repair is covered under the Toyota Powertrain Warranty. This warranty is in effect for 60 months or 60,000 miles, whichever occurs first, from the vehicle’s in-service date. *Warranty application is limited to correction of a problem based upon a customer’s specific complaint

2003 Ducati ST4s Timing Belt Adjustment

0

Filed Under (Aprilia) by admin on 31-10-2010

download
This instruction on cam belt adjustment starts after you remove the fairing pieces. Plan on an hour to remove these. Since you are performing your own service, buying Ducati belts may not be that expensive. There may be another belt source, but I have not confirmed this for the 996 engine of the 02-03 ST4s. Fig 1 – ST4s ready for belt adj./ repl. Fig 2 – Crank tool installed. See dwg. 1) Ensure maximum of ½ tank of gas. Fuel will leak into the charcoal canister, then onto the floor if the tank is over half full and the tank is tilted up on its hinge. So put the tank up on its hinge. 2) Remove spark plugs. Cover sparkplug wells with boots or rags. This is a great time to toss out those Champions for a set of NGK DCPR8E’s. 3) Remove the front shield from the horizontal cylinder head. 4) Remove crankshaft cover on Riders LH side and insert crank tool. A crank tool can be made by following the drawing at the end of this document. See Fig 2 above. The flat head screws used are kind of soft so beware on their removal. 5) Remove oil pressure sending unit cable and remove oil sending unit. No oil should pour out. 6) Remove battery and remove bolts fastening battery box to engine/frame. You can let the battery box dangle or partially support it via a bungee cord. Be careful of the cable on the ground of the ECU. By dangling the battery box excess stress could be placed on this cables connector and you don’t want to troubleshoot an intermittent electrical issue. 7) Remove cam belt covers. The two covers over the cams are real easy. The center piece is removed by pulling it down. You may have to move some hoses and cables out Timing belt adj. doc 1
of the way because it is a tight fit. Removing the oil pressure sending unit gave clearance for the removal. Fig 1 shows bike ready to be worked on. On the Rider’s LH is a window on the case cover. Using a flashlight to illuminate the area, marks can be rotated into view using the engine turning tool. There are two marks denoting the TDC of each of the cylinders. When a mark in the window aligns with the pointer, look at the crank driving pulley on the Rider’s RH of the engine. If the driving pulley’s mark is aligned with the pointer on the engine case, you are at TDC horizontal cylinder. If the pulley mark and the pointer on the engine do not align, rotate the engine until the mark in the window on the Rider’s LH side case cover aligns as well as the pulley’s mark and the engine’s pointer. Fig 3 shows the engine pulley and pointer. You can check that the horizontal piston is at TDC by inserting a welding rod into the spark plug well and touch the top of the piston with it to sense its position. Timing marks on cam pulleys are clearly stamped on all four pulleys. When the crank driving pulley aligns with its corresponding pointer on the engine case and the marks on the pulleys align with their corresponding marks on both cylinders, you are in position for belt adjustment and replacement

Incoming search terms:

YAMAHA XS650H/ SH Supplementary Service Manual

0

Filed Under (Yamaha) by admin on 21-11-2010

download
Ignition timing check 1. Ignition timing is checked with a timing light by observing the position of the rotor pointer and the marks stamped on the timing plate. The timing plate is marked as follows. “ll” Firing range for No. 1 (L.H.) “T” Top Dead Center for No. 1, fL.H.1 cylinder 2. Connect the timing light to the left cylinder spark plug lead wire. 3. Start the engine and keep the engine speed as specified. Use a tachometer to check the engine speed. B. PICK-UP COIL ASSEMBLY The method of mounting the pick-up coil assembly is changed for easier service work. Thus, the followings “Pick-up coil assembly removal” and “Pick-up coil assembly reinstallation” should be changed. Pick-up coil assembly removal Remove the pick-up coil securing screws and remove the pick-up coil assembly. Pick-up coil assembly reinstallation Install the pick-up coil assembly on to the stator assembly. _ L 4. Specified engine speed: 1,200 r/min The rotor pointer should be within the limits of ” fl ” on the timing plate. If it exceeds the limits or does not steady, check the timing plate for tight- ness and/or ignition system for damage. NOTE: Ignition timing is not adjustable. C. FUEL LEVEL The carburetor is furnished with a drain screw to provide easy access to service work. Thus, the following “Fuel level measurement” should be added. Fuel level measurement NOTE: Before checking the fuel level, note the follow- ing: 1. Place the motorcycle on a level surface. 2. Adjust the motorcycle position by placing a suitable stand or a garage jack under the engine so that the carburetor is positioned vertically. 1. 2. Connect the level gauge (special tool) or a vinyl pipe of 6 mm (0.24 in) in inside diameter to the float bowl nozzle left or right side carburetor. Set the gauge as shown and loosen the drain screw 3. Start the engine and stop it after a few minutes of run. This procedure is neces- sary to obtain the correct fuel level. NOTE: Make sure the fuel petcock is “ON” or “RES” oosition. 4. Note the fuel level and bring the gauge to the other end of the carburetor line and repeat step 3 above. Note the fuel level again and compare it with the previous gauge reading. They should be equal. If not, place a suitable size of wooden piece or the. alike under the center stand and adjust. 5. Check the fuel level one by one. The level should be in the specified range.

Incoming search terms:

2003 – 2005 Sequoia, 2004 – 2005 Highlander, Sienna, And Tundra DIAGNOSTIC GUIDE FOR REAR SEAT ENTERTAINMENT SYSTEMS

0

Filed Under (Toyota Manuals) by admin on 08-10-2011

download
Check the power, ground, and TX+, TX- wiring between the RSE ECU and the display. Perform the following check without disconnecting any connectors. A. Using the EWD, check the resistance of the wires between the DVD player ground terminal or integrated DVD player/RSE display and chassis ground. The resistance of the wires should be below 1 Ω. Refer to the Technical Information System (TIS): applicable model year Wiring Diagrams. B. Check the resistance of the wires between the RSE ECU ground terminal and chassis ground. The resistance of the wires should be below 1 Ω. C. Check the voltage on the power terminals on the DVD player and the RSE ECU. Voltage should be greater than 12 V. D. Check the voltage between terminals TX+ and chassis ground and TX- and chassis ground at both the RSE ECU and the DVD player. Voltage should be between 2.0 V and 3.0 V Check the resistance of the wires between the RSE ECU and the radio/player. The resistance of the wires should be below 1Ω. C. Check the resistance of the wires between the RSE ECU and the radio/player to ground. The resistance of the wires should be 10 kΩ or higher

Incoming search terms: