2003 v rod 200 rear tire

You search Auto repair manual PDF 2003 v rod 200 rear tire, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2003 v rod 200 rear tire Direct Download speed 5282 Kb/s

  2003 v rod 200 rear tire Full Version speed 6162 Kb/s



2001 – 2002 GL1800/ GL1800A Rear Tire Inspection

0

Filed Under (Honda) by admin on 27-11-2010

download
1. Inspect the motorcycle for a punch mark as described in Identification on page 2. If a punch mark is present no further action is necessary, return the unit to the customer. 2. Qualify the unit/customer as follows: •Is the tire on the motorcycle the original factory installed tire? •Is the air pressure loss more than three psi per month? Note: Refer to page 145 in the Owner’s Manual. “Even tires that are in good condition may lose one to two psi per month if not checked and adjusted regularly” . If the GL1800 meets the above qualifications, proceed with the repair procedure. 3. Place the motorcycle on a lift and secure it on the centerstand. 4. Remove the rear wheel as described on page 14-9 of the Service Manual. 5. Starting at the valve stem/balance mark area, carefully remove the rear tire from the wheel. Be sure to use plenty of commercially available tire lubricant on the inside and outside of both beads. 6. Carefully inspect the entire circumference of both tire beads. Inspect both the inside and outside of the bead for any distortion or injuries. See examples of injuries below. 2001 – 2002 GL1800/GL1800A Rear Tire Inspection GL1800 #6 OCTOBER 2001 MTB 9430 (0109) CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your Honda. These procedures should not be attempted by “do-ityourselfers,” and you should not assume this bulletin applies to your Honda, or that your Honda has the condition described. To determine whether this information applies, contact an authorized Honda dealer. Service Bulletin American Honda Motor Co., Inc. 2001-2002 GL1800/GL1800A Rear Tire Inspection 0110 GL1800 #6*GL1800 #6*0110*2001-2002 GL1800/GL1800A Rear Tire Inspection*GL1800/GL1800A, Rear Tire Inspection, Bead, Tread*Motorcycle*1800 2 of 4 ©2001 American Honda Motor Co., Inc. – All Rights Reserved GL1800 #6 OCTOBER 2001 Inside BeadInjury Outside BeadInjury Outside BeadInjury 7. Carefully inspect the entire circumference of both tire beads. Inspect both the inside and outside of the bead for any distortion or injuries. See examples of injuries below. 8. If there is no evidence of bead damage, re-install the tire on the rim. Be sure to use plenty of commercially available tire lubricant on the inside and outside of both beads. Be sure to align the balance dot with the valve stem. Inflate the tire to 41 psi. Install the wheel assembly on the motorcycle and proceed to the Identification and then to the Warranty section. 9. If any damage or injury is present replace the tire and valve stem. Be sure to use plenty of commercially available tire lubricant on the inside and outside of both beads. Balance the new tire as necessary

Incoming search terms:

Yamaha V-Star 1100 Custom and Classic cruisers Floorboard/ Footpeg Extension Installation Instructions

0

Filed Under (Yamaha) by admin on 09-11-2010

download
Start on the right (brake) side. 1) Loosen the nut at the end of the brake rod. This will allow you to unscrew the brake rod from the brake lever clevis later. 2) Pull out the cotter pin and remove the pivot pin. Unscrew the clevis 3) Then using a 14mm socket or box-end wrench, remove the two bolts that hold the brake floorboard/footpeg assembly (whichever your bike has) to the frame. These bolts are torqued to 46 ft lbs, so this may be a bit difficult. 1. Loosen this nut 2. Remove the cotter pin (other side of this pivot pin) remove the pivot pin a unscrew the nut to remove the clevis nd 3. Remove these bolts When you remove the floorboard/footpeg bracket, be careful not to pull the brake switch wires loose. You may wish to cut the cable tie for more room, and then rest the bracket, with the footpeg or floorboard attached, on a short box, or block of wood, to keep it handy. Install the new brake rod, to the end of the existing brake rod. Re-install the pivot pin, and the pivot pin cotter pin. Installing the extension bar: Note that the extension bar is bolted so that it rises up in front. Use the new bolts to mount the floorboard/ footpeg bracket to the threaded holes in front. Install the Extension in the proper orientation (angled holes bolt up to the frame, with front of the bar higher than the rear – see photo) using the stock bolts for the extensions to the frame and the new bolts and washers supplied with the kit, on the forward threaded section to relocate the floorboard or footpeg bracket. The use of LocTite ® Blue here is recommended. At this point the right side Floorboard or Footpeg should be secured tightly and the brake lever hanging loose. Now install the Brake rod extension, threading the male end to the original brake rod. Don’t tighten this end yet Place the clevis over the forward most end of the brake rod extension, and threat the clevis nut onto the end of the rod. Bring the brake rod upright, to meet with the clevis at the end of the brake rod extension and replace the pivot pin. Before reinstalling the cotter pin, check the angle of the brake lever, to insure that you have the brake pedal where you want. If necessary, adjust the extension rod in or out, until you are satisfied, and then reinstall the cotter pin into the pivot pin. Check the Brake switch wire and install a new cable tie if required. Note: Due to utilizing a thicker material, 1/2″ versus 3/8″ from our competitor, the Brake rod is now positioned at a greater angle. Even with the angle, braking performance is not affected, but if you wish to bring the master cylinder in line with the brake rod, do this. Loosen the rear, and remove the front Allen bolt. Then place two washers behind the front bolt, under the bracket, and then re-install the bolts To change the angle of the brake rod, 1) loosen and remove the two master cylinder bracket Allen bolts 2) insert two washers behind the front bolt (front of the bike), behind the master cylinder bracket 3) tighten both bolts. Do not install any washers on the rear mounting hole. This will make the angle of the Brake Rod less aggressive. Step Two – Left Side For the left (Shifter) side, 1) use an open-end 10 mm wrench, to unscrew the two nuts that hold the shift rod in place. PLEASE note that one end of the shift rod has a left hand threaded nut. SAVE the nuts, as you will need them on the new longer Polished Stainless Steel Shift Rod. 2) Remove the stock shift rod. 3) Then using a 14mm socket or box-end wrench, remove the two bolts that hold the shifter floorboard/footpeg assembly (whichever your bike has) to the frame.

Incoming search terms:

1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

1999-2008 FLHT Series Harley- Davidson Trike Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect negative Battery Terminal. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Save the Passenger Handrail and two nuts. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove five ¼ – 20 HHCS, ¼ – 20 nyloc nuts, and Aluminum Spacers. 13. Remove Tour Pak from Top Support Tube. 14. Loosen Muffler Clamp on both Mufflers and remove 2 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 15. Remove and discard Muffler Support Plates. 16. Remove both ¼ – 20 HHCS and Front Saddle Bag Brackets. 17. Remove the twelve 5/16 – 18 Torx HCS six 5/16 – 18 nuts, and the Left and Right Saddle Bag Guards. 18. Remove the Air Line Junction from the Rear Fender. 19. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip.
6 20. Remove two 5/16 – 18 Phillips head screws. Remove the Left and Right Frame Covers. 21. Remove two 5/16 – 18 Torx HCS. Remove and save the Top Tour Pak Support Tube Top. 22. Remove four 5/16 – 18 Torx HCS. Remove the Left and Right Rear Saddle Bag Guard Support Bracket. 23. Remove four 5/16 – 18 HHCS. Remove and save the Tour Pak Support Tube Bottom. 24. Remove and discard the Air Valve Assembly Bracket. 25. Remove four ½ – 13 HHCS and washers. Remove and discard both Rear Air Shock Absorbers. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. 26. Drain all Brake Fluid from the Rear Brake System. 27. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 28. Remove the 10 – 24 flanged HHCS and Rear Brake Hose Clamp from the Right Rear Fork Bracket. 29. Remove ¼ – 20 SHCS from Rear Stop Lamp Switch Bracket. 30. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 31. Remove the Spring Clip and nut from the Rear Axle. 32. Remove Rear Axle and Rear Wheel Spacers. 33. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 34. Remove Rear Brake Caliper. 35. Slide Rear Wheel Assembly rearward. Remove one 5/16 – 18 Torx HCS from inside the Rear Fender well. 36. Slide Rear Wheel Assembly forward. Remove two 5/16 – 18 Torx HCS. Remove Rear Fender. 37. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate

Incoming search terms:

Harley Davidson Road Rod Saddle Bag System Kit INSTALLATION Instructions

0

Filed Under (Harley Davidson) by admin on 16-04-2012

download
Use locktite on all fasteners!! 2. Put bike on lift and place jack under frame. Raise bike to lift rear wheel. 3. If swing arm pivot shaft is drilled and tapped on each end, they need to be redrilled and tapped to 3/8-16 to a depth of _” deep. If you are unable to drill & tap your swing arm pivot shaft, you can purchase one from Cycle Visions (part #CV6121), See Harley Davidson® V-Rod® Service Manual Section 2, Page 2.89 for removal and installation instructions. 4. Remove seat, passenger seat, turn signal module, rear fender cover, turn signal license plate assembly, and rear foot peg assemblies. NOTE: Our bag system will not work with stock exhaust system… we recommend the 2-into-1 Supertrap, or you may use any exhaust system that is lower than the rear axle bolt. 5. Remove the two upper shock bolts. Relocate the shock spacer from the right side to the left side, and use the new spacer supplied on the right side. 6. Install front bag mount between frame and spacer (see Figure 1), reinstall shock bolts and torque to 31-50 lbs. 7. Install lower bag support frame to swing arm pivot shaft using the 3/8″ bolt through rear foot peg clevis and cover (see in Figure 2). NOTE: There is a right and left covers and bag support, install accordingly. Torque to 35 foot lbs. 8. Install rear fender front mounting tabs using 8mm 1.25 x _ and flat washers (supplied in kit) (see Figure 3). 9. Install upright saddlebag support brackets to the lower bag mount assembly and lower fender extension crossover mount. (see Figure 4). Torque to 25 lbs. NOTE: Install crossover mount with gusset facing down. 10. Remove license plate light from your rear turn signal bracket license plate assembly. Install license plate light on our license plate light bracket (see Figure 5). 11. Install the license plate bracket on the inside of the rear fender extension using the top holes of the license plate frame (see Figure 6 & 7). 12. Install fender washers on the inside of the fender extension (see Figure 8). 13. Install upper fender bracket to rear fender extension with a _-20 bolt supplied in kit (see Figure 9). 14. Install rear fender extension with chrome button fitted bolts. (see Figure 10 & 11). 15. To check alignment and fit of rear fender extension reinstall original rear fender. Once you have everything lined up and fitted, remove original rear fender, drill & tap (2) two 5/16 x 18 holes in rear fender support bracket (see Figure 12). 16. Install Harley Davidson® Part #70909-95 and 47449-97 bracket and receptacle on front and rear bag supports (see Figure 13 & 14). 17. Install Harley Davidson® Part #47449-97 bracket with receptable (see Figure 14). Make sure the bolts come from the inside out. This bracket is adjustable for location.

Turbo+2 , Roadstar , Quantum Sport , Quantum"GL" , Entourage Owners Manual

0

Filed Under (Uncategorized) by admin on 03-12-2010

download
tracking Any parting within the tread, sidewall, or inner liner of the tire extending to cord material. CT A pneumatic tire with an inverted flange tire and rim system in which the rim is designed with rim flanges pointed radially inward and the tire is designed to fit on the underside of the rim in a manner that encloses the rim flanges inside the air cavity of the tire. Curb weight The weight of a motor vehicle with standard equipment including the maximum capacity of fuel, oil, and coolant, and, if so equipped, air conditioning and additional weight optional engine. Extra load tire A tire designed to operate at higher loads and at higher inflation pressures than the corresponding standard tire. Groove The space between two adjacent tread ribs. Gross AxleWeight Rating The maximum weight that any axle can support, as published on the Certification /VIN label on the front left side of the trailer. Actual weight determined by weighing each axle on a public scale, with the trailer attached to the towing vehicle. Gross Vehicle Weight Rating The maximum weight of the fully loaded trailer, as published on the Certification /VIN label. Actual weight determined by weighing trailer on a public scale, without being attached to the towing vehicle. Hitch Weight The downward force exerted on the hitch ball by the trailer coupler. Innerliner The layer(s) forming the inside surface of a tubeless tire that contains the inflating medium within the tire. Innerliner separation The parting of the innerliner from cord material in the carcass. Intended outboard sidewall The sidewall that contains a white-wall, bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire or the outward facing sidewall of an asymmetrical tire that has a particular side that must always face outward when mounted on a vehicle. Light truck (LT) tire A tire designated by its manufacturer as primarily intended for use on lightweight trucks or multipurpose passenger vehicles. Load rating The maximum load that a tire is rated to carry fora given inflation pressure. Maximum load rating The load rating fora tire at the maximum permissible inflation pressure for that tire. Maximum permissible inflation pressure he maximum cold inflation pressure to which a tire maybe inflated.
-9- Maximum loaded vehicle weight The sum of curb weight, accessory weight, vehicle capacity weight, and production options weight. Measuring rim The rim on which a tire is fitted for physical dimension requirements. Pin Weight The downward force applied to the 5thwheelor gooseneck ball, by the trailer kingpin or gooseneck coupler.

Incoming search terms:

HARLEY DAVIDSON REAR TYPHOON WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-02-2011

download
INSTALLATION 1. Remove existing rear wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to REAR WHEEL in Service Manual. NOTES Prior to removing or installing the wheel, the rear brake caliper must be removed. The cotter pin or spring clip for the axle nut must be replaced. They are available for purchase from a dealer. See a dealer for the correct part number for your model motorcycle. Use plastic protectors on tire mounting tools and rim clamps when mounting a tire to a painted wheel. For wide low profile tires a tire mounting machine with a second arm to press down on the sidewall while the wheel is rotating is recommended. When mounting tires, liberally use tire lube on the wheel and tire. For tire removal, use plastic inserts between the rim and tire after breaking the bead to create a large enough gap for the rim clamps. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) 2. See Figure 1. Install valve stem assembly (E) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components, stock brake disc, and sprocket to wheel using the service parts table. Refer to REAR WHEEL in Service Manual. NOTES Install the primary bearing first using service manual and WHEEL BEARING REMOVER/INSTALLER. The machined grooves in the hub face indicate the primary bearing side. 4. Install rear wheel (1), stock axle, and stock spacers to motorcycle. Refer to REAR WHEEL in service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner

HARLEY DAVIDSON VRSC SADDLEBAG SUPPORT KIT (WIDE TIRE) REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
REMOVAL Remove Pillion and Rear Fender NOTE If possible, lift the rear of the motorcycle up so the rear wheel drops to the bottom of shock travel. This will help provide clearance between the rear tire and fender when installing the mounting brackets. 1. Open the rider seat. 2. See Figure 1. Remove rider seat post (1), nut (2), and washer (3) from passenger pillion. Slide grabstrap (4) forward off pillion. Save mounting hardware for kit installation. 3. Push passenger pillion forward to release slot on bottom of pillion from post on fender tongue. 4. See Figure 2. Lift pillion up to remove lanyard (1) from hole in center of passenger pillion (2). Then lift pillion away from motorcycle. 5. Disconnect turn signal and tail light electrical connections from back of rear electrical caddy. Note position for later installation. 6. See Figure 3. Unsnap rear electrical caddy (1) from rear inner fender. 7. Remove and save two fender support bolts (2), washers (3), and grabstrap (4) from rear fender. 1 2 3 4 is03548 1. Rider seat post 2. Nut 3. Washer 4. Grabstrap Figure 1. Passenger Pillion and Mounting 2 1 3 i03571 1. Seat lanyard 2. Hole in pillion 3. Passenger pillion Figure 2. Seat Lanyard and Passenger Pillion 8. Remove four remaining fender support bolts (2) and washers (3) near center of rear fender. 9. Remove rear fender from vehicle. 3 2 4 2 3 2 3 1 is03544 1. Rear electrical caddy 2. Fender support bolt (6) 3. Washer (6) 4. Grabstrap Figure 3. Grabstrap, Rear Electrical Caddy, and Fender INSTALLATION Install Attach/Release Weldment, Rear Fender, and Grabstrap NOTE Apply Loctite 243 (blue) to last four threads of leave-on bracket screws. 1. See Figure 4. Install leave-on bracket (1) to outside surface of inner fender using two button head screws (2) and nuts (3). Tighten screws to 48 Nm (35 ft-lbs). Repeat for opposite side. 2. See Figure 5. Install release/attach weldment (1) to leave- on brackets (2) using two washers (3) and socket head cap screws (4). Tighten screws to 25 Nm (18 ft-lbs). Repeat for opposite side.

TOYOTA Suspension Tire Inflation Pressure Compensation and Adjustment

0

Filed Under (Toyota Manuals) by admin on 06-10-2011

download
2004-2010 4Runner 2007-2010 Avalon, Camry, Camry HV, RAV4, Sienna 2008-2010 Corolla, FJ Cruiser, Highlander, Highlander HV, Matrix, Yar is 2006-2010 Land Cruiser, Prius, Tacoma 2005-2010 Sequoia, Tundra 2007-2008 Solara 2009-2010 Venza The purpose of this bulletin is to provide a procedure to adjust tire pressure correctly when outside temperature is significantly colder or warmer than shop temperature. Seasonal temperature change can dramatically alter tire pressure, which can cause the tire pressure warning lamp to illuminate. Tire temperature is dependent on”cold”tire pressure, driving distance and speed, ambient temperature and road surface temperature. As the temperature of the tire changes, air in the tire expands and contr acts, changing the tire’sairpressure. The cold tire pressure for all Toyota models will vary and will need to be adjusted accordingly. “Cold”tire pressure, as shown on the tire pressure label on our vehicles, is generally considered to be the pressure in a tire that has not been driven in the past 4 hours and has been parked outdoors. The TPWS MUST be initialized with the tire pressure marked on the vehicle placard. Tires are then adjusted according to the information in this bulletin to ensure that the TPWS light does not illuminate unnecessarily.

Incoming search terms:

HARLEY DAVIDSON V-ROD CHROME REAR TURN SIGNAL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION Prepare the Motorcycle 1. Remove the right cover and the maxi-fuse. 2. Follow Service Manual instructions to remove the air box cover. Remove the Existing Rear Turn Signals 1. For 2006 and Earlier Models: See Figure 1. Insert a screwdriver into middle of hole of license plate light cover. Push forward to release tail lamp housing retaining clip. 2. See Figure 3. Identify the white left [19] (1) and black right [18] (2) 2 pin rear turn signal connectors. 3. See Figure 6. To separate the rear turn signal connector, press the button (1) and separate the pin terminal housing from the socket terminal housing. 4. On the socket terminal housing, press the latch (2) aside and open the secondary lock (3). 5. To remove the rear turn signal wires from the socket terminal housing, insert a pin (6) into the front socket cavity. Compress the tang (4) while gently pulling the wire and socket terminal (5) from the back. 6. See Figure 7. Inside the fender, remove the fasteners (1) and the turn signal support plate (2). Pull the turn signal wiring through holes in license plate mounting bracket and remove turn signals. 7. Repeat for the opposite turn signal. 1. For 2007 and Later Models: See Figure 2. Open seat and remove the nut and washer (3), seat post (2), passenger pillion and passenger seat (1) per the instructions in the Service Manual. 2. See Figure 4. Identify the left (1) and right (2) rear turn signal wires and 6 pin rear turn signal connector [94]. 3. See Figure 6. To separate the rear turn signal connector, press the button (1) and separate the pin terminal housing from the socket terminal housing. 4. On the socket terminal housing, press the latch (2) aside and open the secondary lock (3). 5. See Figure 5. Remove the turn signal wires from the 6 pin socket terminal housing. To remove the wires, insert a pin (6) into the front socket cavity. Compress the tang (4) while gently pulling the wire and socket terminal (5) from the back. Repeat for all four turn signal wires. Do not remove the license light wires from the socket terminal housing. 6. Gently pull the loose turn signal wires through the sheath toward the rear of the vehicle until completely removed from the sheath. 7. See Figure 7. Inside the fender, remove the fasteners (1) and the turn signal support plate (2). Pull the turn signal wiring through holes in license plate mounting bracket and remove turn signals. 8. Repeat for the opposite turn signal

Incoming search terms:

Incoming search terms: