2003 vstar 650 speedo bulb

You search Auto repair manual PDF 2003 vstar 650 speedo bulb, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2003 vstar 650 speedo bulb Direct Download speed 5282 Kb/s

  2003 vstar 650 speedo bulb Full Version speed 6162 Kb/s



YAMAHA V-MAX PERIODIC MAINTENANCE AND MINOR REPAIR

0

Filed Under (Yamaha) by admin on 25-11-2010

download
PERIODIC MAINTENANCE AND MINOR REPAIR -. 1. Screw (x 2) EAU03003 Replacing the headlight bulb This motorcycle is equipped with a quartz bulb headlight. If the headlight bulb burns out, replace it as follows. 1. Remove the headlight unit by re- moving the screws. 2. Disconnect the headlight coupler, and then remove the headlight unit and bulb cover. 1. Headlight bulb holder 3. Remove the headlight bulb holder by turning it counterclockwise, and then remove the defective bulb. EWOOOl19 Headlight bulbs get very hot. Therefore, keep flammable products away from a lit headlight bulb, and do not touch the bulb until it has cooled down. 4. Place a new bulb into position, and then secure it with the bulb holder. 1. Do not touch this area. EC000105 Do not touch the glass part of the headlight bulb to keep it free from oil, otherwise the transparency of the glass, the luminosity of the bulb, and the bulb life will be adversely affected. Thoroughly clean off any dirt and fingerprints on the headlight bulb using a cloth moistened with alcohol or thinner. 5. Install the bulb cover, and then connect the coupler. 6. Install the headlight unit by install- ing the screws. 7. Have a Yamaha dealer adjust the headlight beam if necessary. 6-40 PERIODIC MAINTENANCE AND MINOR REPAIR 1. Screw (x 2) 1. Tail/brake light bulb (x 2) EAU00855 Replacing a turn signal light bulb or the tail/brake light bulb 3. Insert a new bulb into the socket, push it in, and then turn it clock- wise until it stops. 1. Remove the lens by removing the screws. 2. Remove the defective bulb by pushing it in and turning it counter- clockwise. 1. Turn signal light bulb 4. Install the lens by installing the screws. EC000108 Do not overtighten the screws, oth- erwise the lens may break

Incoming search terms:

Single-Cylinder BMW G 650 X Model Series

0

Filed Under (BMW) by admin on 16-11-2010

download
introducing the new range of single-cylinder models, BMW Motorrad is broadening its model line-up with a clear focus on additional target groups. Proceeding from the same technical foundation, the Company has created three new motorcycles absolutely different in their features and characteristics: the G 650 Xchallenge Hard Enduro, G 650 Xmoto Street Moto, and the G 650 Xcountry Scrambler. With their outstanding product substance, their purist looks, and their exceptionally sporting riding characteristics, these single-cylinder models are filling attractive niches in the market. And through their low unladen weight of less than 160 kg or 353 lb according to the DIN standard, they offer dynamic performance for both the connoisseur and the sports-minded rider. Market launch of the new G 650 X model series is planned in good time for the beginning of the season in spring 2007. These new machines with the smallest engines in the BMW model range offer particularly the young and young-at-heart motorcycle rider exactly the right entry into the world of BMW motorcycles, but are not entry-level bikes in the conventional sense of the word: On the contrary, the G 650 Xchallenge Hard Enduro will thrill the customer who wishes to really benefit from the enormous offroad potential of his machine. The G 650 Xmoto Street Moto, in turn, with its very impressive active riding qualities, offers the genuine enthusiast a new dimension in riding pleasure. The G 650 Xcountry Scrambler, finally, stands for carefree riding pleasure and nimble performance both on the road and off the beaten track. Indeed, this unique machine is able to meet all kinds of requirements and offer virtually all riding qualities ranging from city use via country roads and small, winding lanes, all the way to offroad tracks presenting the most challenging requirements. The G 650 Xcountry therefore conveys the classic but relaxed feeling of riding a genuine Scrambler as well as the concept of “wandering” on your motorcycle into today’s world in a most modern style. And last but certainly not least, riding pleasure is guaranteed under all conditions and in every situation, since the G 650 Xcountry offers the same outstanding engine and running gear qualities as its two very sporting “sister models

Incoming search terms:

ODYSSEY DRYCELL MOTORCYCLE BATTERY COMPATIBILITY

0

Filed Under (Triumph) by admin on 30-10-2010

download
BMW 1200 1200 1150 1100 1100 1000 1000 1000 1000 900 850 800 800 800 750 750 750 750 750 650 650 600 600 500 BUELL 1200 1200 1200 1000 DUCATI 860 750 500 HARLEY DAVIDSON 1570 1570 1450 1450 1340 1340 1340 1200 883 HONDA 1800 1500 1200 1100 1000 1000 900 750 750 650 650 650 600 400 200 150 150 125 K1200RS, LT R1200C R1150GS, R R1100GS/R R1100RS/T/S/LT “K” Models R100/7 100RS R100GS, R, RS, RT R90/6, R90S R850R R80GS, R80ST R80, R80RT R80/7/RT K75, RT K75C, S R75/5 R75/7 R75/6 R65 R65LS R60/5 R60/6, R60/7 R50/5 S1 Lightning X1, S3, S3T, M2 S2/T, RS1200, RR1200 RR1000 GT, GTS GT, Laguna Seca GTL, GTV, Sport FXST, FLST FXD FXD FXST, FLST FXD FXST, FLST FL/H/T/HT XL, XLH XLH, XLH GL1800, VTX1800C Gold Wing-All Gold Wing-All Gold Wing-GL1100 CBX1000, SS opt. Gold Wing-GL1000 CBR900R,RR CB750A (Hondamatic) VFR740R/ RVF750R NT650, SLR650, NX650 Vigor 650 XR650L VT600C, CD, CBR600 CBR400F CB-1 TR200 Fat Cat CH150 Elite FES150 FES125, Pantheon (97 -) (98 -) (00 -) (94-00) (90 -) (83-93) (76-84) (83) (87-95) (69-76) (95-97) (80-96) (84-95) (78-84) (85-95) (85-95) (70-73) (76-84) (69-76) (84-95) (78-84) (70-73) (69-84) (70-73) (96-99) (ALL) (ALL) (87) (2007) (2007) (99-06) (00-06) (97-99) (91-99) (80-96) (97-03) (97-02) (01-06) (88-00) (84-87) (80-83) (82) (75-79) (93-99) (76-78) (90/94) (88-91) (ALL) (93-06) (87-03) (89-90) (86) (87) (ALL) (ALL) #3561 #3561 #3561 #3561 #3561 #4989 #4989 #3561 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #3591** #3591 #3591 #3591 #4989 #4989 #3561 #3591 #2528 #2528 #3591 #2528 #3591 #3560 #2528** #2528** #2528 #3560* #3560* #3560* #3560* #3560* #2519* #3560* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* PC680 PC680 PC680 PC680 PC680 PC925L PC925L PC680 PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC545MJ PC545MJ PC545MJ PC545MJ PC925L PC925L PC680 PC545MJ PC545 PC545 PC545MJ PC545 PC545MJ PC680MJ PC545 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 cc model (year) cat. # mfg sku # KAWASAKI 1500 1500 1300 1000 1000 900 900 750 750 650 636 600 600 KTM 640 620 400 400 MOTO GUZZ I 1100 1100 1100 1000 1000 850 850 750 650 650 650 500 POLARIS All SUZUKI 1400 900 750 750 750 650 600 600 600 600 400 TRIUMPH 600 YAMAHA 1600 1300 1300 1200 1100 1100 1100 920 600 600 VN 1500-A Vulcan VN 1500-C Vulcan KZ 1300 Touring KZ 1000-P Police Z1000 ZX900-C, Ninja ZX900-E, F Ninja KZ750-L, Ninja Zx750 Ninja ZX, 7RR KLX650C, R ZX636-B Ninja ZX-6R ZX600-G, J Ninja ZX ZX600-K Ninja ZX Adventure, Duke, RXC Adventure, Duke, LC4 LC4 E/XC RXC LC4 Cali/Spc/Jackl/Stone/EV Quota/Sport 1100 VII EV/Bassa California III,Quota,Millie Convert,Daytona, LeMans LeMans T3, T4, T5 Nevada,NTX,Strada,V7,V75 NTX V65 V65 Florida V50 Victory GV 1400GC RF900, R, S, ZS GSX750F Katana GSX-R750 GSXR750W DR650SE GSF600S Bandit GSX600F Katana GSX-R600 RF600R, S GSF400 Bandit Daytona 600 XV 1600 Road Star 1300 Royal Star XVZ Venture Royale XVZ12T Venture XJ1100 Maxim XS 1100, L, S XV 1100, S/ Virago XV 920/R/M Virago XJ600S Seca II XT600E (87-98) (96-97) (79-82) (82-05) (03-04) (98-99) (00-04) (93) (91-97) (93-96) (03-04) (98-02) (03) (99-02) (96-98) (96-98) (96-01) (94-05) (97-02) (98-99) (ALL) (86-88) (94-97) (98-03) (96-99) (94-95) (96-04) (96-03) (98-04) (97-03) (94-96) (91-93) (03-04) (99-03) (96-03) (86-92) (83-85) (82) (78-92) (86-99) (81-83) (92-98) (90-95) #3560 #3560 #3560 #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #4989 #2528 #4989 #4989 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #4989 #2519* #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2528*** #2528*** #3560 #3560 #3560 #3560 #3560 #3560 #2519* #2519* PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC925L PC545 PC925L PC925L PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC925L PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310

Incoming search terms:

Harley Davidson Speedo Healer Installation Manual

0

Filed Under (Harley Davidson) by admin on 14-03-2012

download
a) Locate the three wire Deutsche connector that is situated behind the left hand side panel as viewed from the rear of the bike. This is normally grey in colour, and the wires are coloured red, white and black. This connector connects the rear wheel sensor to the electronic speedo head. OEM Connector b) The table below shows the function of each wire Colour Function Red +ve volts White Signal to Speedo Black GND Green Signal from Rear Pickup The +ve volts red wire should be between 8 and 12 volts, typically it is only 8 volts which is on the limit of the Speedohealer range and it is necessary to source an alternative 12 volts supply e.g. from the fuse box. I used a feed from the accessory supply which is an Orange/White wire (You need a switched +12V so don’t use the battery positive terminal.) c) Tap into the wires from the rear wheel pick and solder the Speedo healer ensuring to use the provided heat shrink cable to cover the finished work. Wiring loom Note the red wire is not used from the connector. The green wire is the feed from the rear wheel sensor which is connected to the input wire (white or yellow) of the Speedohealer. The output of the Speedohealer which is the blue wire is connected to the white wire which goes to the Harley speedo. d) Get the power from the fuse box Alternative 12 volt from fuse box Alternative 12 volt from fuse box closeup e) A suitable location for the Speedohealer is on the side of the battery box. It can be fixed by using a cable tie. Fitted to battery box f) Finally this is the OEM electronic speedo (as seen from the front and rear) and the rear wheel pickup

2008-2009 KAWASAKI TERYX HEADLAMPS HIDTERYX HID KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
a. Remove rubber boot from the back of the headlamp housing assembly. b. Push down on metal latch and pull away from lip to release halogen bulb. Pull out halogen bulb. c. Insert HID bulb, line up bulb to fit into the bulb holder, lower latch to lock bulb in place. d. Replace Rubber boot on the back headlamp assembly. (Make sure to pull wires through the center of the rubber boot first before you start to pull down boot on the back of the headlamp assembly.) e. Make sure that the wiring, coming from the HID bulb, clears the black plastic housing that encases the headlamp assembly so connection from the bulb to the ballast is possible. If installed correctly there is no need for drilling or modifications of any type. 2. Ballast a. Mount ballast in location of your choice – recommended near the headlight. 3. Wiring Note: DO NOT modify the wiring that runs from the HID bulb to the ballast. It will cause the system to work improperly. It will void the warranty . a. Once ballast is installed connect corresponding wires from HID bulb to corresponding male / female plugs on ballast. b. To connect wiring from ballast to Teryx primary system i. Find wire extension with white triangular head with black, yellow & green wires at opposite end ii. Connect black off extension to black wire coming off ballast iii. Connect Yellow / Green wire to red wire coming off ballast iv. Connect triangular head to corresponding plug on Teryx Factory Wiring End

2003 SUZUKI SV 650 COOLING AND LUBRICATION SYSTEM SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
COOLING CIRCUIT INSPECTION Before removing the radiator and draining the engine coolant, inspect the cooling circuit for tightness. • * Remove the cowling. (SV650S) (C-7–7-6) • * Loosen the radiator cap stop screw 10 . (SV650) • * Remove the radiator cap O2 and connect the radiator tester to the filler. A WARNING Do not remove the radiator cap when the engine is hot. • * Give a pressure of about 120 kPa (1 .2 kgf/cm2,17.0 psi) and see if the system holds this pressure for 10 seconds . • * If the pressure should fall during this 10-second interval, it means that there is a leaking point in the system . In such a case, inspect the entire system and replace the leaking component or part. A WARNING When removing the radiator cap tester, put a rag on the filler to prevent spouting of engine coolant. CAUTION Do not allow the pressure to exceed specified pressure, or the radiator can be damaged. COOLING AND LUBRICATION SYSTEM 6-3 6-4COOLING AND LUBRICATION SYSTEM RADIATOR REMOVAL • * Remove the cowling. (SV650S) ( r- 7-7-6) • * Drain engine coolant. (r– 72-20) • * Disconnect the right and left radiator hoses from the radiator. • * Disconnect the siphon hose from the radiator. • * Disconnect the horn lead wires. rI .rr • * Remove the radiator lower mounting bolt. • * Disconnect the cooling fan motor and its thermo-switch lead wire coupler 10. • * Remove the radiator by upper mounting bolt. • * Remove the cooling fan. • * Disconnect the cooling fan thermo-switch. • * Remove the cooling fan thermo-switch. • * Remove the horn. CAUTION When removing the horn, hold the nut by spanner to prevent the horn bracket distortion. COOLING AND LUBRICATION SYSTEM 6-5 INSTALLATION • * Install the cooling fan and horn. 0 Cooling fan/horn mounting bolt: 8 N .m (0.8 kgf-m, 6 .0 Ib-ft) • * Install the cooling fan thermo-switch. ( l”76-9) • * Install the siphon hose to the radiator. • * Install the radiator in the reverse order of removal. • * Route the radiator hoses properly. (=9-22) 9-22) • * Install the drain plug with a new sealing washer and pour engine coolant. (=2-20) • * Bleed air from the cooling circuit. (r– 72-21) • * Install the cowling. (SV650S)

Incoming search terms:

2003 SUZUKI SV 650 FUEL SYSTEM AND THROTTLE BODY SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
FUEL PUMP The electric fuel pump is mounted at the bottom of the fuel tank, which consists of the armature, magnet, impeller, brush, check valve and relief valve . The ECM controls its ON/OFF operation as controlled under the FUEL PUMP CONTROL SYSTEM . When electrical energy is supplied to the fuel pump, the motor in the pump runs and together with the impel- ler . This causes a pressure difference to occur on both sides of the impeller as there are many grooves around it . Then the fuel is drawn through the inlet port, and with its pressure increased, it is discharged through the outlet port . The fuel pump has a check valve to keep some pressure in the fuel feed hose even when the fuel pump is stopped . Also, the relief valve is equipped in the fuel pump, which releases pressurized fuel to the fuel tank when the outlet of the fuel pressure has increased up to 450 -600 kPa (4.5- 6.0 kgf/cm2,64- 85 psi) . Relief valve Brush , ∎ I,’ Check valve Magnet L Armature When the impeller is driven by the motor, pressure differential occurs between the front part and the rear part of the blade groove as viewed in angular direction due to fluid friction . This process continuously takes place causing fuel pressure to be built up . The pressurized fuel is then let out from the pump chamber and discharged through the motor section and the check valve . FUEL SYSTEM AND THROTTLE BODY 5- 3 Inlet port I I Impeller 5-4 FUEL SYSTEM AND THROTTLE BODY FUEL PRESSURE REGULATOR The fuel pressure regulator consists of the spring and valve . It keeps absolute fuel pressure of 300 kPa (3.0 kgf/cm2,43 psi) to be applied to the injector at all times . When the fuel pressure rises more than 300 kPa (3 .0 kgf/cm2, 43 psi), the fuel pushes the valve in the regulator open and excess fuel returns to the fuel tank . 90 Spring 02 Valve FUEL INJECTOR The fuel injector consists of the solenoid coil, plunger, needle valve and filter . It is an electromagnetic type injection nozzle which injects fuel in the throttle body according to the signal from the ECM. When the solenoid coil of the injector is energized by the ECM, it becomes an electromagnet and attracts the plunger. At the same time, the needle valve incorporated with the plunger opens and the injector which is under the fuel pressure injects fuel in conic dispersion . As the lift stroke of the needle valve of the injector is set constant, the volume of the fuel injected at one time is determined by the length of time during which the solenoid coil is energized (injection time)

Incoming search terms:

2001 – 2003 Prius 2003 4Runner, Camry, Land Cruiser and Sequoia VEHICLES EQUIPPED WITH TRANSPONDER ECU

0

Filed Under (Toyota Manuals) by admin on 07-10-2011

download
When replacing the ECM (SAE term: PCM) or the Transponder ECU a “handshake” procedure must be performed. This ECU ID communication is necessary to enable the Transponder ECU and the ECM to recognize each other before the vehicle will start. Complete ECU communication using the following steps: 1. Insert a Master key into the ignition cylinder. 2. Turn the ignition ON (engine OFF). 3. Short Tc and CG terminals of DLC3 using the Diagnostic Check Wire (SST 09843-18020 or equivalent) and leave for 30 minutes. 4. After 30 minutes, turn the ignition OFF and remove check wire from DLC3. 5. Register any additional keys as necessary. 6. Start the vehicle to confirm successful ECU communication. Key Programming: To program or delete a key, a registered Master key is necessary unless the Transponder ECU has been reset or replaced. The Transponder ECU system incorporates a black “Master” key and a gray “Sub” key. The process during registration of these two keys is identical. The key itself now determines if it functions as Master or Sub, not the registration procedure. The maximum number of allowable Master and Sub keys vary by model. Refer to the chart below.

BMW F 650 CS Rear belt wheel cracks Removal And Installation Manual

0

Filed Under (BMW) by admin on 12-11-2010

download
Relieve the tension of the toothed belt and lift the belt off the belt wheel (refer to F 650CS Repair Manual, 00.57). 2) Remove 6 screws (see arrow in photo at right). 3) Remove the rear belt wheel. 4) Clean and degrease the tapered bores and the threads of the mounting screws 5) Carefully place the new belt wheel in position on the damper, coat the screw threads with Loctite 243 and hand tighten the securing screws. 6) Tighten the securing screws to the specified torque maintaining a diagonally opposite tightening sequence throughout (Torque to 28 NM, curing time 12 hours). 7) Measure the vertical runout of the belt wheel (refer to F 650 CS Repair Manual, 33.15). 8) Install and adjust the rear drive belt (refer to F 650 CS Repair Manual 00.57 – 00.58) 2.1 Removal of the front belt wheel Remove the front belt wheel in accordance with the instructions detailed in the F 650 CS Repair Manual. Remove the securing screw of the activated charcoal filter and let the filter canister hang by one side by the hoses, or remove it and lay it aside. Clean the splines and threads of the main shaft in order to remove all traces of Loctite. If necessary, remove corrosion from the main shaft spline (use only a brass bristle brush). 2.2 Visual inspection Check the splines of the main shaft for damage. Replace the main shaft if the splines are damaged (broken, chipped, bent or damaged teeth). Refer to the F 650 CS Repair Manual for this procedure.

Incoming search terms:

BMW Motorcycle F 650 GS/ F 800 GS Accessories

0

Filed Under (BMW) by admin on 20-11-2010

download
Stowage-equipment line Vario case, black, left 71 60 7 696 299 £184 / G Vario case, black, right 71 60 7 696 300 £185 / G (+) Case carrier for Vario case, including fasteners 71 60 7 696 301 £144 / G (+) Lock barrel, complete, for 2 cases 51 25 7 688 566 £20.80 / I (o) Lock barrel by code for vehicle and/or case matching locks (order 2x) 51 25 7 681 199 £33.59 (o) Lock-barrel set 51 25 7 698 202 £15.20 / I Liner for Vario case, left 71 60 7 687 610 £67 / I Liner for Vario case, right, and Vario topcase 71 60 7 687 611 £67 / I Vario topcase, black 71 60 7 696 302 £225 / I (+) Luggage rack, large, for Vario topcase (including adapter plate) 71 60 7 696 303 £64 / I (+) Lock barrel for topcase 51 25 7 688 568 £12.50 / I (o) Lock barrel by code for vehicle and/or case matching locks (order 1x) 51 25 7 681 199 £33.60 / I (o) Lock barrels for 2 cases and topcase 51 25 7 688 567 £29.10 / I Liner for Vario case, right, and Vario topcase 71 60 7 687 611 £67 / I Backrest pad for topcase 71 60 7 688 877 £45 / I Luggage carrier, small 71 60 7 701 810 £42.90 / G Tank rucksack, waterproof 71 60 7 711 240 £130 / I Enduro rear softbag 71 60 7 711 245 £35.90 / I Sport softbag, small, 19 l 71 60 7 694 117 £102 / I Sport softbag, large, 51 l 71 60 7 693 567 £139 / I Stuffbag, waterproof, 53 l 72 60 7 653 818 £90 / I Luggage strap with pull-tight buckle 72 60 2 304 808 £6.30 / E Bungee-cord spider 72 60 9 057 579 £3.95 / E Design line Spray-guard extension, rear 71 60 7 695 031 £24.20 / I Sound components Akrapović sports silencer 71 60 7 713 339 *1 £475 / G Ergonomics and comfort line Windscreen, large, tinted 71 60 7 713 834 *1 £138 / I Windscreen, large, clear (standard for F 800 GS) 71 60 7 713 833 £127 / I Windscreen, small, clear (standard for F 650 GS) 71 60 7 713 296 £87 / I Centre stand (F 650 GS) 46 52 7 700 864 *2 £83 / I Centre stand (F 800 GS) 46 52 7 700 049 *2 £91.50 / I (+) Fasteners for centre stand (F 650 GS + F 800 GS) 71 60 7 706 738 £24.90 / I Seat, low, black, 790 mm (F 650 GS), 850 mm ( F 800 GS) 52 53 7 695 013 £174 / I Heated handlebar grips and switches (see electronic parts catalogue) Navigation and communication components BMW Motorrad Navigator III plus 2008 72 60 7 716 116 *1 £650 / I (+) Holder for BMW Motorrad Navigator 71 60 7 697 785 £45.80 / E (+) Securing screw (order 4 of) 32 71 7 652 161 £4.55 / I Connecting cable for BMW Motorrad Navigator 71 60 7 686 670 £55 / E TMC module for BMW Motorrad Navigator 72 60 7 702 687 *1/3 £111 / E Car kit for BMW Motorrad Navigator 72 60 7 703 996 *3 £60.50 / E Navigator carry-bag function 71 60 7 683 161 £49 / I Safety line Hand-protector bar 71 60 7 716 043 £57 / I (+) Countersunk-head screw (order 2 of) 32 71 7 712 836 £3.34 / E Hand protector, small 71 60 7 705 963 £19.50 / I Hand protector, large 71 60 7 715 135 £23.10 / I Protector-mounted spoiler for hand protector, large 71 60 7 705 964 £15.20 / I Crash bar, left 71 60 7 699 437 £104 / I Crash bar, right 71 60 7 699 438 £104 / I (+) Fasteners for crash bar 71 60 7 702 395

Incoming search terms: