2004 harley softail crank but wont start

You search Auto repair manual PDF 2004 harley softail crank but wont start, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2004 harley softail crank but wont start Direct Download speed 5282 Kb/s

  2004 harley softail crank but wont start Full Version speed 6162 Kb/s



HARLEY DAVIDSON SOFTAIL FRONT SPOILER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 2 and Table 1. INSTALLATION 1. Position the vehicle on a motorcycle lift table. To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 2. Refer to the Service Manual and follow the instructions given to remove the Maxi® Fuse. 3. Raise the vehicle on the lift table to allow access to the lower front portion of the frame. 2008+ 2007 7 8 11 3 3 4 4 12 5 5 1 1 9 2 2 10 6 6 9 9 11 13 is02652c 8. 1. Two-pin voltage regulator connector (2007 only) Voltage regulator 2. 9. Voltage regulator attaching screws (2) Cable strap (2 for 2007, 1 for 2008 and later) 10. 3. Lower voltage regulator cover (2007 only) Voltage regulator bracket 4. 11. Bracket screw to engine crankcase (2) Oxygen sensor connector 12. 5. Crank position sensor connector (2007 only) Voltage regulator caddy 6. 13. Voltage regulator caddy cover Horn connectors (some 2008 and later models) 7. Four-pin voltage regulator connector (2007 only) Figure 1. Original Equipment Voltage Regulator  NOTE For 2007 models: The ground wire on the voltage regulator must be re-attached at the original location when re-installing the voltage regulator to ensure adequate ground. 4. For ALL models: See Figure 1. Remove and discard the voltage regulator caddy cover (6) from the regulator bracket (3) and caddy (5). For 2007 models: In addition, remove the lower voltage regulator cover (10). 5. Remove and retain the hex socket head screw (4) at the top left of the bracket For 2007 models: In addition, disconnect the ground wire. Free the cable straps (9) from the regulator bracket, beneath the regulator. 6. Remove the two hex socket head screws with washers (2) retaining the voltage regulator to the bracket. Remove and save the regulator, but discard the screws. 7. Remove and retain the screw (4) at the top right of the regulator bracket. Remove the bracket from the engine. 8. For 2008 and later models: Free the strap (9) that ties the jiffy stand wiring to the voltage regulator bracket. Unfasten the three-way jiffy stand sensor connector and the two-way crank position sensor connector [79] (12) from the T-studs on the back of the regulator bracket (3). Discard the bracket. Disconnect both plugs from the back of the voltage regulator (1). For 2007 models: Unfasten the four-way (7) and two-way (8) voltage regulator connectors from the T-studs on the back of the regulator bracket (3), and discard the bracket. Disconnect the voltage regulator (1) at both connectors. 9. For 2008 and later models: Unclip the two-way O 2 (oxygen) sensor electrical connector [138] (11) from the voltage regulator caddy (5). For 2007 models: Unfasten the two-way crank position sensor connector [79] (12) from the voltage regulator caddy (5). Remove the caddy from the vehicle frame. a. For 2007 models: Unclamp the bottom of the caddy from the engine mount spacers. b. For ALL models: Unhook the top clips from around the tabs on the front of the engine casting. Remove the original equipment (O.E.) caddy from the vehicle frame, and discard it.

Incoming search terms:

2004 Honda CRF450R OWNER'S MANUAL

0

Filed Under (Honda) by admin on 21-11-2010

download
motorcycle can be kickstarted with the transmission in gear by disengaging the clutch before operating the kickstarter. Check the engine oil, transmission oil and coolant levels before starting the engine (page 21, 23, 24). Cold Engine Starting: 1. Turn the fuel valve ON. 2. Shift the transmission into neutral. 3. If the temperature is 35°C (95°F) or below, pull the choke knob fully out. 4. If the temperature is below 0°C (32°F), open the throttle two or three times. (The engine requires a richer mixture for starting in cold weather. When the throttle is so opened, the accelerator pump will feed extra fuel to the cylinder, thereby facilitating starting in cold weather.) 5. With the throttle closed, operate the kickstarter starting from the top of the kickstarter stroke, kick through to the bottom with a rapid, continuous motion. (Do not open the throttle, As the carburetor is equipped with an accelerator pump, excessive fuel will be charged into the engine, and the spark plug will be fouled if the throttle is opened and closed repeatedly. Excessive fuel in the engine makes kick- starting difficult.) 6. About a minute after the engine starts, push the choke knob back all the way to fully OFF. If idling is unstable, open the throttle slightly. (1) FUEL FILL CAP (2) BREATHER TUBE WARNING (1) FUEL VALVE (2) CHOKE KNOB Warm Engine Starting: 1. Turn the fuel valve ON. 2. Shift the transmission into neutral. 3. Pull the hot start lever and kick-start the engine. (Do not open the throttle.) 4. As soon as the engine starts, release the hot start lever 1. Shift the transmission into neutral. 2. Pull the hot start lever and kick-start the engine. (Do not open the throttle.) 3. As soon as the engine starts, release the hot start lever. Starting the engine excessively charged with fuel by throttle blipping or other reasons: 1. Shift the transmission into neutral. 2. With the throttle fully opened, repeat kickstarter operation approximately 10 times very slowly to discharge excessive fuel from the engine. 3. Pull the hot start lever and kick-start the engine (Do not open the throttle.) 4. As soon as the engine starts, release the hot start lever. Stopping The Engine 1. Shift the transmission into neutral. 2. Turn the fuel valve OFF. 3. Lightly open the throttle 2 – 3 times, and then close it. 4. Depress and hold the engine stop button until the engine stops completely. NOTE: • Failure to close the fuel valve may cause the carburetor to overflow. (1) THROTTLE GRIP (2) ENGINE STOP BUTTON Break-In Procedure Help assure your CRF’s future reliability and performance by paying extra attention to how you ride during the first operating day or 15 miles (25 km). During this period, avoid full-throttle starts and rapid acceleration. This same procedure should be followed each time when: • Piston is replaced • Rings are replaced • Cylinder is replaced • Crankshaft or crank bearing are replaced

Incoming search terms:

REKLUSE MOTOR SPORTS Pro Start Clutch Harley-Davidson OWNER'S MANUAL

0

Filed Under (Harley Davidson) by admin on 24-11-2010

download
REAK-IN PERIOD The ProStart clutch requires a short break-in period. During the break-in period, the ProStart should not be operated at steady engine speeds above 3000 RPMs for more than 10 minutes. Breaking-in the ProStart clutch equires start and stop cycles. Riding the ProStart clutch in stop-and-go city traffic for one hour will provide sufficient break-in. If you would like to accelerate the break-in period, find an empty parking lot with ample room and no other traffic. From a stop, bring the motorcycle to 20 miles per hour and then back to a stop. Repeat this process at least 20 times. MAINTENANCE Proper maintenance is important to ensure the longevity of the Rekluse ProStart clutch and the rest of the stock clutch components in your Harley- Davidson Motorcycle. Refer to your owner’s manual for proper primary chaincase oil levels and oil type. Rekluse recommends the use of Harley- Davidson Primary Chaincase lubricant with the Rekluse ProStart clutch. Do not use oils designed for use as automotive engine oil in your Primary Chaincase. If Harley-Davidson Primary Chaincase lubricant is not readily available, a premium-quality Diesel engine oil, such as Shell Rotella T, that does not contain friction modifiers may be substituted. Inspection and adjustment of the Rekluse ProStart clutch should only be performed by a service center trained in Harley-Davidson and Rekluse ProStart repair and maintenance. The Rekluse ProStart clutch should be inspected for adjustment after 1,000 miles of operation. Thereafter, inspection for adjustment should be performed at 5,000 mile intervals

2001 – 2004 Camry, Highlander, Solara & 2004

0

Filed Under (Toyota Manuals) by admin on 12-10-2011

download
2004 model year Camry, Highlander, Solara and 2004 model year RAV4 vehicles with the 2AZ-FE engine may exhibit squealing and/or rattling noises coming from the engine compartment during vehicle operation especially after a cold soak. The belt tensioner assembly has been improved to correct this condition. 2001 – 2004 model year Camry, Highlander and Solara vehicles equipped with 2AZ-FE engines produced BEFORE the Production Change Effective VINs shown below. 2004 model year RAV4 vehicles produced BEFORE the Production Change Effective VINs shown below. MODEL ENGINE LINE PRODUCTION CHANGE EFFECTIVE VIN TMMK Line 1 4T1BE3#K#4U358206 Camry TMMK Line 2 4T1BE3#K#4U914052 y 2AZFE Tsutsumi JTDBE3#K#40296732 Highlander 2AZ-FE TMK JTE#D2#A#40100501 Solara TMMK 4T1CE3#P#4U914074 RAV4 Tahara JTE#D2#V#40029797 PREVIOUS PART NUMBERCURRENT PART NUMBER PART NAME QTY 16620-28010 16620-28011 Tensioner Assembly, V-ribbed Belt 1 OP CODE DESCRIPTION TIME OFP T1 T2 EG8001 R & R Accessory Belt Tensioner 0.9 16620-28010 91 55 Applicable Warranty*: This repair is covered under the Toyota Comprehensive Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle’s in-service date. *Warranty application is limited to correction of a problem based upon a customer’s specific complaint

Incoming search terms:

2004 Harley Davidson Micro Tach Tachometer Installation Instructions

0

Filed Under (Harley Davidson) by admin on 26-03-2012

download
Tachometer Installation Instructions for 2004+ Harley Davidson Sportster Custom Look for other model instructions online at www.speedwayinstruments.com Introduction: Installation of the Speedway Instruments microTach+ TM tachometer Tachometer requires some basic mechanical skills, including removing decorative covers, cutting protective tubing around wires, and using suitcase splice connectors to splice existing wiring harness. These actions may void your warranty, and if done incorrectly may cause damage to your motorcycle. Only you know your capabilities, if you do not feel capable of making modification please have a qualified motorcycle technician install it. Speedway Instruments, LLC is not responsible for damage to your motorcycle due to improper installation. These instructions utilize a 2004 Harley Davidson XL1200C motorcycle as basis for the all descriptions and pictures. Variations in location, color and procedure may be required for different year and make. Please refer to the Service manual to confirm the proper color and location of wires. Please make sure you have the proper service manual and tools before starting the installation. 1. Turn ignition off and disconnect Battery. 2. Determine a mounting position. Each motorcycle is unique and the microTach+TM tachometer is small enough to be placed in many different locations to provide an attractive appearance and vital engine status. Possible locations are: a. Front Brake Reservior b. Top handle bar clamp

Harley Davidson Softail Motorcycles EZ-Steer Installation Manual

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
Softail EZ-Steer Instruction Supplement Installation of the Champion EZ-Steer system is similar to the installation of the OEM triple clamps of your Harley Davidson Softail Motorcycle. We strongly recommend that you use your OEM service manual and follow the prescribed disassembly, installation and torque specifications (except where noted below) for the upper and lower clamp assembly. Installation Notes • Note the torque specifications for the items listed below. Item # Description (Qty) Torque Spec. (Lb.Ft.) N/A OEM Steering Stem Bolt (1) 35 7 7/16-20 x 1.5 Socket Head Cap Screw (2) 45 • The supplied fork tube extensions (Item #2) must be used with the Champion EZ-Steer system. • Do not torque the steering stem bolt until fork tubes have been installed to the assembly. • Remove O-rings from OEM fork tube ends and install to Champion fork tube extensions (Item #2) prior to installation onto fork tubes. • The supplied fork tube covers (Item #9) must be installed to lower triple clamp prior to installation of fork tubes. WARNING: If the Champion EZ-Steer system is installed on a motorcycle / sidecar combination and the sidecar is removed, the motorcycle is not safe to ride, and OEM triple clamps should be replaced.

Incoming search terms:

Harley-Davidson Electronic Fuel Injection Tuner INSTALLATION Manual

0

Filed Under (Harley Davidson) by admin on 14-04-2012

download
Harley-Davidson Electronic Sequential Port Fuel Injection System, (ESPFI) This completely new engine management system was released starting with select 2001 model year Softail motorcycles. This system is a speed/density, open loop, sequential port fuel injection design that also controls spark timing and spark intensity. Speed/Density System – When the ECM monitors manifold air pressure, air temperature, throttle position and engine rpm to manage fuel delivery. Open Loop Control – When the ECM monitors sensors positioned on the intake side of the engine and does not monitor the end result of internal combustion at the exhaust. Sequential Port Fuel Injection – When the injector nozzle is positioned in the manifold near the intake valve and is precisely timed to deliver fuel to each cylinder. This ESPFI system is the exclusive design used on 2001 and Later EFI-equipped Softail models, 2002 and Later EFI-equipped Touring models, 2004 and Later Dyna models, and 2004 and later V-Rod models. Current ESPFI Components The following is a list of the major components of Harley-Davidson’s current ESPFI system. It is important to have an understanding of what these components do before learning how the ESPFI system functions. Refer to the appropriate Harley-Davidson Service Manual for the vehicle you are working on for additional information on component design and function and for the physical location and testing procedures for each individual component. ECM – Electronic Control Module – this is the brain of the system that collects input signals from multiple sensors, makes decisions and sends output signals to deliver fuel and spark to the engine. CKP – Crank Position Sensor – this sensor provides input signals to the ECM that indicate engine rpm, (how fast the engine is running in R evolutions P er M inute). The ECM also uses these inputs to determine what stroke the engine is in so it can deliver the fuel and spark at the desired time.

2007 Softail HARLEY DAVIDSON FUEL PUMP/ FUEL GAUGE SENDING UNIT REMOVAL AND INSTALLATION

0

Filed Under (Harley Davidson) by admin on 30-03-2012

download
1. Remove seat. 1 WARNING 1 WARNING To prevent spray of fuel, purge system of high-pressure fuel before supply line is disconnected. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00275a) 2. Purge the fuel supply line of high pressure gasoline. a. See Figure 4-36. Disconnect the fuel pump fuse from the main wiring harness. b. Start the engine and allow the vehicle to run. c. When the engine stalls, operate the starter for 3 seconds to remove any remaining fuel from the fuel lines. 1 WARNING 1 WARNING To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 3. Disconnect negative battery cable. 4. Remove instrument console. a. All but FXSTD, see Figure 4-37. Remove acorn nut and washer on instrument console to separate console from fuel tank. b. For FXSTD, see 8.26 INSTRUMENT CONSOLE: FXSTD. 5. Disconnect console wiring. Figure 4-36. Fuel Pump Fuse: View From Top Figure 4-37. Acorn Nut And Washer: All But FXSTD s0660x8xx 7526
4-28 2007 Softail: Fuel System HOME 1 WARNING 1 WARNING Gasoline can drain from the crossover line when disconnected from fuel tank. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00259a) 6. Drain fuel tank. a. Obtain a short section of hose (5/16 inch I.D.). Insert bolt in one end of hose and install hose clamp to ensure that end is securely plugged. b. See Figure 4-38. Cut clamp (1) from one end of crossover hose (2). Quickly replace crossover hose on fuel tank fitting with open end of short hose while directing flow of gasoline from free end of crossover hose into suitable container. 7. See Figure 4-39. Unplug fuel pump module connector (3) [86]. 8. Remove top plate screws (2) and discard. 9. See Figure 4-40. Pull top plate (2) out of fuel tank enough to expose fuel hose and clamp (1). CAUTION Carefully inspect end of hose for cuts, tears, holes or other damage. Replace hose if any damage is found. Even the smallest hole can cause a reduction in fuel pressure. 10. Cut clamp and remove hose from regulator housing fit- ting.

Incoming search terms:

2004 Ford Harley Davidson F-250 Super Duty Installation Manual

0

Filed Under (Harley Davidson) by admin on 13-03-2012

download
1. Using a 13MM socket, remove the bolt from just forward the front tire holding the bumper support. Do this to both sides of the vehicle. Set bolts and bumper support aside to be reinstalled later. 1 1 ‘ ‘ ‘ ‘ 2004 Ford Harley-Davidson F-250 Super Duty Installation Instructions BX2608 Installlation Instructions: ‘ ‘ Page 4 of 5 405-0061 Rev. A 5/18/09 4. Set the baseplate inside the opening. Underneath start three 1/2″-13 x 1 3/4″ hex bolts with 1/2″ lock washers. Be sure and use loctite on all bolts before tightening. 3. If the vehicle has tow hooks, underneath the frame end are three metric bolts to remove using a 15MM socket. Pull tow hooks forward and set aside. Do this to both sides of the vehicle. The tow hooks will Using an 18MM socket, remove two bolts from the end of the frame. Disconnect the fog lights. Do this to both sides of the vehicle. Pull the bumper forward to remove. Set bolts and the bumper aside to be reinstalled later

HARLEY DAVIDSON FLSTC SOFTAIL SADDLEBAG KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 16-04-2011

download
Additional Fitment Information Detachables NOTE If motorcycle has not been altered from fixed saddlebag hardware to accessory mounting detachable docking points. the separate purchase of Turn Signal Mounting Bar (Part Number 68611-98) is required for sufficient lock clearance. This kit is available at your Harley-Davidson Dealer. Installing these saddlebags on models equipped with a detachable sissy bar or detachable luggage rack requires the additional purchase of mounting hardware kit as follows: Hardware Kit Fitment 53075-03 2003 and later FLSTC models with detachables 53009-03 1987 through 2002 FLSTC models with detachables See Service Parts Page for kit contents. Additional weight can affect motorcycle stability, handling characteristics, and safe operating speed. Do not exceed 7 lbs. (3.18Kg) maximum load in each saddlebag. Evenly distribute weight between each saddlebag. Improper loading can cause vehicle handling problems leading to death or serious injury. Wide Tire If a wide tire kit has been installed, utilize the hardware and installation instructions found in that kit to reorient the fasteners to come from the inside to the outside of the finder. Button head screws from wide tire kit must be installed from the inside out, with the button heads on the inside of the fender. Failure to do so could result in bolt contacting tire, which could result in death or serious injury. Installation NOTE A Service Manual for your vehicle is available at your Harley-Davidson Dealer. 1. Remove seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. (00048a) Disconnect the negative (-) battery cable first. If positive (+) cable should contact ground with the negative (-) cable connected, the resulting sparks may cause a battery explosion which could result in death or serious injury. (00049a) 2. Disconnect battery cables, negative cable first. 3. Following instructions in applicable Service Manual, remove original saddlebags from supports. Install Turn Signal Mounting Bar If motorcycle is not equipped with accessory mounting detachable docking points, install Turn Signal Mounting Bar (Part No. 68611-98) following instructions provided with the kit. See Figure 1

Incoming search terms: