2004 honda crf 230 spark plug gap

You search Auto repair manual PDF 2004 honda crf 230 spark plug gap, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2004 honda crf 230 spark plug gap Direct Download speed 5282 Kb/s

  2004 honda crf 230 spark plug gap Full Version speed 6162 Kb/s



SUZUKI SV1000 PERIODIC MAINTENANCE

0

Filed Under (Suzuki) by admin on 26-02-2011

download
MAINTENANCE AND TUNE-UP PRO- CEDURES This section describes the servicing procedures for each item of the Periodic Maintenance requirements. AIR CLEANER I Inspect every 6 000 km (4 000 miles, 6 months) and replace every 18 000 km (11 000 miles, 18 months) . • * Remove the seat. (LF6-7) • * Lift and support the feul tank . (C-74-65) • * Remove the air cleaner box cap O. • * Remove the air cleaner element O. • * Carefully use air hose to blow the dust from the cleaner ele- ment. CAUTION Always use air pressure on the throttle body side of the air cleaner element . If air pressure is used on the other side, dirt will be forced into the pores of the air cleaner element thus restricting air flow through the air cleaner element . PERIODIC MAINTENANCE 2-5 2-6PERIODIC MAINTENANCE • * Reinstall the cleaned or new air cleaner element in the reverse order of removal . CAUTION If driving under dusty condition, clean the air cleaner element more frequently. The surest way to accelerate engine wear is to use the engine without the element or to use a ruptured element. Make sure that the air cleaner is in good condition at all times. Life of the engine depends largely on this component! NOTE: When cleaning the air cleaner element, drain water from the air cleaner by removing the drain plug . SPARK PLUG Inspect every 6 000 km (4 000 miles, 6 months) and replace every 12 000 km (7 500 miles, 12 months) . No. 1 (FRONT) SPARK PLUG REMOVAL • * Remove the radiator mounting bolt O. • * Move the radiator forward. • * Remove the spark plug cap O. NOTE: Be careful not to damage the radiator fins . A WARNING The hot radiator and the hot engine can burn you . Wait until the radiator and the engine are cool enough to touch . • * Remove the spark plug with a spark plug wrench. 1 6 I It No. 2 (REAR) SPARK PLUG REMOVAL • * Remove the seat. (r–,-6-7) • * Lift and support the fuel tank . (=4-65) 4-65) • * Disconnect the camshaft position sensor 1O and breather hose (Z. • * Remove the rubber heat shield ® . • * Remove the spark plug cap . • * Remove the spark plug with a spark plug wrench . HEAT RANGE • * Check to see the heat range of the plug . CARBON DEPOSIT •Check to see if there are carbon deposits on the plugs . If carbon is deposited, remove it with a spark plug cleaner machine or carefully using a tool with a pointed end . SPARK PLUG GAP • * Measure the plug gap with a thickness gauge . If out of specification, adjust it to the following gap . 09900-20803 : Thickness gauge Spark plug gap OA Standard: 0.6 – 0 .7 mm (0.024 -0.028 in) ELECTRODES CONDITION •Check to see the worn or burnt condition of the electrodes . If it is extremely worn or burnt, replace the plug . And also replace the plug if it has a broken insulator, damaged thread . CAUTION Confirm the thread size and reach when replacing the plug. If the reach is too short, carbon will be deposited on the screw portion of the plug hole and engine damage may result

Incoming search terms:

Honda CG125 Owners Workshop Manual

0

Filed Under (Honda) by admin on 25-11-2010

download
Clean the air filter Pull off the right-hand side panel and remove the two nuts which secure the air filter cover. Withdraw the cover, checking that the sealing gasket is in good condition, pull out the retaining spring and withdraw the element assembly. Peel off the inner and outer foam sleeves. Wash all components in white spirit (Stoddard solvent) or in warm water and detergent and dry them thoroughly. Soak the foam sleeves in the specified oil, then squeeze them gently (do not wring them out or they will be damaged) to expel all surplus oil. Refit the sleeves to the element frame. On reassembly ensure that all components are correctly fitted so that unfiltered air cannot bypass the element. 2 Check the spark plug Remove the spark plug cap, unscrew the plug and check its condition, comparing it with the photographs on page 65. If it is badly worn or fouled it must be renewed. If it is fit for further service check the gap and reset it if necessary, as described in Chapter 3.8. 3 Check the valve clearances It is important that the correct valve clearance is maintained. A small amount of free play is designed into the valve train to allow for expansion of the various components. If the setting deviates greatly from that specified, a marked drop in performance will be evident. In the case of the clearance becoming too great, it will be found that valve operation will be noisy, and performance will drop off as a result of the valves not opening fully. If on the other hand, the clearance is too small the valves may not close completely. This will not only cause loss of compression, but will also cause the valves to burn out very quickly. In extreme cases, a valve head may strike the piston crown, causing extensive damage to the engine. The clearances should be checked and adjusted with a cold engine. Place the machine on its centre stand and remove the rocker cover, taking care not to damage the 0 ring. Remove the gearchange pedal and the left-hand outer cover to expose the generator rotor. Remove plug and allow old oil to drain Remove the spark plug, then slowly rotate the engine anticlockwise by way of the generator rotor, watching the inlet valve. When it has opened and closed again (sunk down and risen up to its original position), rotate the engine further until the T mark on the rotor periphery aligns exactly with the raised index mark which is positioned between 12 and 1 o’clock (from the crankshaft) on the generator stator. The engine will then be in the correct position for checking the valve clearances, namely at Top Dead Centre (TDC) on the compression stroke; check that there is free play at both rockers. Using a 0.08 mm (0.003 in) feeler gauge, check the clearance between the top of each valve stem and its corresponding rocker. The feeler gauge must be a light sliding fit, with the rocker and valve stem just nipping it. If necessary, slacken the locknut, and turn the small square-headed adjuster to obtain the correct setting. Tighten the locknut, holding the adjuster at the same time to prevent it from moving. Finally, recheck the setting and then repeat the procedure on the other rocker. 4 Check the contact breaker points and ignition timing Note: since the generator stator plate is located by its countersunk retaining screws, the ignition timing can only be altered by opening or closing the contact breaker gap; therefore both operations are described as one. The full procedure is given here for ease of reference, but if the points are found to be in good condition and if the gap has not altered or is within the tolerance, then the ignition timing will be sufficiently accurate and there will be no need to carry out the full check. First remove the gearchange pedal, the left-hand outer cover, the spark plug and the left-hand side panel

Honda VT1100 Shadow Guide Plug Patch Repair Manual

0

Filed Under (Honda) by admin on 24-04-2011

download
Find the guide plug.bn The guide plug is shown in the shop manual with the engine removed from the frame and the left crankcase cover removed. (You’ll find this illustration in the “ELECTRIC STARTER/STARTER CLUTCH” chapter in the “STARTER DRIVEN GEAR/STARTER CLUTCH REMOVAL” section.) It’s a little bit harder to find it on the bike. Start by following the yardstick to see where the guide plug is on my bike. To find it on your bike, lie on the ground (or, preferably a mechanics creeper) next to the bike (without the yardstick) and peek under the shift lever and over the frame There it is, just barely visible from the side of the bike. Here’s what a new one looks like: 2. Clean the guide plug and crankcase. From the front of the bike, clean the guide plug and crankcase with brake cleaner in a VERY focused spray. Let the cleaner evaporate before moving to the next step. Page 4 Rev: Draft 5/20/2007 Page 4 of 5 3. Reposition the guide plug. a. From the side of the bike, use the yardstick (or a long screwdriver if you prefer) to gently push the guide plug back into the crankcase. (Note the JB Weld from the previous patch operation.) b. From the front of the bike, gently push upward on the bottom of the upper tab (as shown below) or the bottom of the forward tab to rotate the guide plug into the proper position while maintaining pressure with the yardstick

Incoming search terms:

HONDA 2008 CRF 450 F SLIP-ON EXHAUST SYSTEM REPAIR MANUALS

0

Filed Under (Honda) by admin on 25-12-2011

download
The Akrapovic Slip-On system is designed for recreational Honda CRF 450 enthusiasts. It delivers an excellent combination of quality, performance, visual enhancement, easy installation and affordability. The Akrapovic Slip-On is designed for two markets; in the US it is available with an approved spark arrester, and for the EU and other non-US markets it comes with a noise damper. PERFORMANCE Measurements of the Akrapovic SLIP-ON system on the HONDA CRF 450 R (with muffler insert): Power & Torque: Up to 5600 rpm the Akrapovic Slip-On essentially follows the stock power and torque curves. It shows its true colors above that range, where it delivers significant increases to both power and torque. Max. increased power of 2.8 HP was measured at 6600 rpm. At the top of the rpm range the Akrapovic curves again follow the stock power and torque curves. CONFIGURATION The system is composed of a flared stainless steel link pipe which is welded to the muffler. It is attached to the stock header assembly with a sleeve joint secured with a metal clamp. The muffler is the offroad design with a titanium outer sleeve, and stainless steel inlet cap, outlet cap and inner perforation. The muffler is attached to the frame using an Akrapovic carbon-fiber clamp. In the US the system is available with an approved spark arrester, and for the EU and other non-US markets it comes with a standard noise damper

Incoming search terms:

HONDA CB650/ 750F/ 900F/ 1100F/ GL1100 Spark Unit Set Installation Manual

0

Filed Under (Honda) by admin on 05-04-2011

download
INSTALLATION INSTRUCTIONS: 1. All connections must be of the highest quality, use crimped or soldered connections; twisted wires will not give a satisfactory operation. 2. Remove the seat and/or petrol tank to gain access to the original spark units (if fitted); these are normally fitted under the seat between the top frame tubing. Each of these units consists of a small alloy metal box with sleeved wires terminated by a small connector (coupler). They also have a mounting tab with a single fixing hole. 3. On four cylinder machines there will be two units, normally mounted back to back; one for cylinders 1&4 and one for cylinders 2&3. 4. For safety, disconnect the battery. 5. Unplug the couplers from each of the units. Undo the fixings and remove the units. 6. Fit the new spark units in the place of the old ones or find a suitable alternative, close to the connectors. Secure the units to the frame or mounting platform using the supplied tie-straps and adhesive mounting base (if required). If required, a thin sheet of rubber or double-sided tape can be used to keep the units in position. Do not completely wrap the units in foam rubber. 7. Push the wiring harness plugs into the new spark unit socket connectors; they will only fit one way. Reconnect the battery. 8. If you are rewiring the machine or do not have the standard wiring harness, the spark unit wire colours & functions are as follows: GREEN Ö GROUND (0 VOLTS) BLACK/WHITE Ö IGNITION SUPPLY (+12 VOLTS) VIA ENGINE STOP SWITCH YELLOW Ö IGNITION COIL OUTPUT (TO COIL —) WHITE Ö PULSE GENERATOR (WHITE RING) BLUE Ö PULSE GENERATOR (UNMARKED) There are two pulse generators, one for cylinders 1&4 and one for cylinders 2&3. The left hand one is normally for cylinders 1&4 (see fig.1). There are two wires of the same colour coming from each pulse generator, one of these wires is normally marked with a white band. The pulse generator wire with the white band connects to the white wire from the corresponding spark unit, the other pulse generator wire connects to the blue wire on the corresponding spark unit. If the white band is missing, this is normally the upper wire coming from the pulse generator. 9. Refit the seat and tank (if removed earlier). 10. Fitting is now complete, although for best results you may wish to verify the ignition timing, see the following guide

Incoming search terms:

SANYANG HD 125/ 200 Specifications And SERVICE MANUAL

0

Filed Under (Sym) by admin on 24-11-2010

download
heck and adjustment Fault condition Probable causes Loosen carburetor drain bolt to check if there is gasoline inside the carburetor Fuel supplied tom carburetor sufficient No fuel is supplied to carburetor Remove spark plug, install it into spark plug cap, and perform a spark test against engine ground. Perform cylinder compression pressure test. Check if sparks Weak sparks, no spark at all Low compression pressure or no pressure Re-start by following the starting procedures No ignition There are some signs of ignition, nut engine can not be started Remove the spark plug again and check it. Remove carburetor after 30 minutes and connect a hose onto fuel rich circuit. Then blow the hose with air Dry spark plug Wet spark plug Blowing in normal Blowing clogged 1. No fuel in fuel tank 2. Check if the pipes, fuel tank to carburetor and intake vacuum, are clogged. 3. Float valve clogged 4. Lines in fuel tank evaporation system clogged 5. Malfunction of fuel pump 6. Loosen or damaged fuel pump vacuum hose 7. Fuel filter clogged 1. Malfunction of spark plug 2. Spark plug foul 3. Malfunction of CDI set 4. Malfunction of AC generator 5. Ignition coil is in open or short circuit 6. Ignition coil leads open or short circuit 7. Malfunction of main switch 1. Piston ring seized 2. Malfunction of cylinder valves 3. Worn cylinder and piston ring 4. Cylinder gasket leak 5. Sand hole in compression parts 1. Malfunction of throttle valve operation 2. Air sucked into intake manifold 3. Incorrect ignition timing 1. Fuel level in carburetor too high 2. Malfunction of throttle valve operation 3. Throttle valve opening too wid

Incoming search terms:

2001 HONDA CRF 230 Dual Sport Kit Installation Manual

0

Filed Under (Honda) by admin on 21-11-2010

download
1. Remove the seat, fuel tank, side panels, and front number plate. 2. Taillight and Turn signal Installation: Note that Baja Designs has updated this kit to use the new style LED taillight. The mounting is the same. Mount the rear taillight assembly to the rear fender as shown in Photos 1 and 2. Transfer drill the mounting holes in the taillight assembly into the fender and mount using the countersunk fasteners provided. The tail light lens should just line up with the end of the fender. Mount the turn signals into the side of the taillight assembly as shown in Photos 1, 2 and 3. The taillight has not been pre-drilled to allow placement of the turnsignals to be varied to accommodate different exhausts. Use a 3/8″ drill for the turn signal mounting hole 3 Photo 3 Photo 2 Photo 1
. 3. Brakelight Switch Installation: This is a tight fit on the CRF230 – take your time and it’ll work. Drill a 1/8″ hole in the brake lever 4 ½” from the center of the brake pedal pivot point (Photo4). 4 Photo 5 Drill 1/8″ hole here Photo 4 Install the brake-switch bracket under the right case bolt directly above the oil filler cap (Photo 5). Attach the spring to the hole you drilled in the pedal. Adjust the switch in the bracket so it engages about halfway through the pedal throw. You may need to lengthen (stretch) the spring slightly to allow proper switch adjustment. Turn-Signal Switch Installation: Install the turn signal switch on the handlebar next to the grip as shown in Photo 6 . The switch has a single screw that pinches it together on one side. Two tabs secure the switch halves on the other side. Remove the screw to separate the halves so that it can be installed on the handlebar. When installing the switch to the handlebar, make sure the tabs are seated in their locating holes and then tighten the pinch screw. DO NOT OVER TIGHTEN THIS SCREW, as too much force can strip the body of the switch. The clutch perch may have to be moved inward slightly to make room for the switch. Run the wires along the bottom of the handle

Incoming search terms:

Ktm CRF-230 Installation and Removal Manual

0

Filed Under (KTM) by admin on 27-01-2012

download
Partially install the headlight assembly using the top right white zip tie only to hold it in place temporarily. You will need to plug wires to this assembly. Step 5: Install handlebar switch on clutch side. You will need to move clutch perch to the right (about ½ inch to1 inch) to make room for the switch. The switch plugs into the circuit board on the bottom of the headlight using the 8-pin plug (the only unused 8-pin one on the circuit board) Step 5: (Power harness) The power wire with the two pin plug runs from the battery to the 6 inch wire hanging from the control board. The red wire should be attached to the positive and the black wire to the negative of battery. You will need to notch the battery cover so the wire can fit with the cover closed. Step 6: (Taillight harness) The wire with the six pin plug is for the tail light. Run the wire down the left side of the bike. If you plan on using a front hydraulic brake switch use the front connectors and continue at Step 7A. If you are planning on using a mechanical rear brake switch use the green pair of connectors and continue at Step 7B. You can use both

Incoming search terms:

2001 – 2004 Camry, Highlander, Solara & 2004

0

Filed Under (Toyota Manuals) by admin on 12-10-2011

download
2004 model year Camry, Highlander, Solara and 2004 model year RAV4 vehicles with the 2AZ-FE engine may exhibit squealing and/or rattling noises coming from the engine compartment during vehicle operation especially after a cold soak. The belt tensioner assembly has been improved to correct this condition. 2001 – 2004 model year Camry, Highlander and Solara vehicles equipped with 2AZ-FE engines produced BEFORE the Production Change Effective VINs shown below. 2004 model year RAV4 vehicles produced BEFORE the Production Change Effective VINs shown below. MODEL ENGINE LINE PRODUCTION CHANGE EFFECTIVE VIN TMMK Line 1 4T1BE3#K#4U358206 Camry TMMK Line 2 4T1BE3#K#4U914052 y 2AZFE Tsutsumi JTDBE3#K#40296732 Highlander 2AZ-FE TMK JTE#D2#A#40100501 Solara TMMK 4T1CE3#P#4U914074 RAV4 Tahara JTE#D2#V#40029797 PREVIOUS PART NUMBERCURRENT PART NUMBER PART NAME QTY 16620-28010 16620-28011 Tensioner Assembly, V-ribbed Belt 1 OP CODE DESCRIPTION TIME OFP T1 T2 EG8001 R & R Accessory Belt Tensioner 0.9 16620-28010 91 55 Applicable Warranty*: This repair is covered under the Toyota Comprehensive Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle’s in-service date. *Warranty application is limited to correction of a problem based upon a customer’s specific complaint

Incoming search terms:

Honda CRF/ TRX 450R Camshaft Installation

0

Filed Under (Honda) by admin on 19-11-2011

download
Break-in of this camshaft is important and you should adhere to all of the following instructions. It is also very important to use plenty of engine assembly lubricant, recommended is Coastal Engine Assembly Lube or Clevite 77, both are available from most automotive supply companies. We recommend you change the engine oil before the initial start-up of the engine after the assembly. Then change the oil again after the break-in of the cams to remove the excess
phosphate from the coated cams. These steps will help ensure that the camshaft breaks-in properly and that you have a long lasting product. Using full synthetic engine oil during break-in is not recommended but, is OK to use after the one-hour break-in period is over. Following a regular maintenance schedule is the best way to ensure durability and performance over the long run. Cleanliness is always a good place to start. Make sure the motorcycle is cleaned thoroughly before you start. It would be advisable to use an engine degreaser on the frame and the engine. Remove the fuel tank and thoroughly clean the inside of the frame rails, around the carburetor, and behind the radiators. Be sure to remove the ignition coil assembly and using high-pressure air, clean the spark plug hole out before the plug is removed. This will ensure a clean engine during the assembly process and less of a chance of thread damage and/or dirt contamination in the engine during reassembly

Incoming search terms:

Incoming search terms: