2004 road king vacuum lines

You search Auto repair manual PDF 2004 road king vacuum lines, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2004 road king vacuum lines Direct Download speed 5282 Kb/s

  2004 road king vacuum lines Full Version speed 6162 Kb/s



HARLEY DAVIDSON ROAD KING SOLO BUCKET AND PASSENGER PILLION INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
Installation SOLO SADDLE ONLY 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider solo seat. 2000 and later models . Remove the retainer washer from the stud plate and replace with two black retainer washers (2). Be careful not to allow stud plate to fall through the fender. 3. Road King standard models . Install stock solo seat mount bracket using two stock screws saved in Step 2. Road King Classic Custom models . Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. Install seat by sliding front of seat into seat holder bracket. Pull up on the nose of the seat to verify that the seat is securely installed. After installing seat, pull upward on front of seat to be sure it is in locked position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070a) 5. 1999 and later models . Install 1/4 in. star washers (6), spacers (4) and acorn nuts (3) onto rear mount studs. Torque to 72 in-lbs (8.13 Nm). 1998 and earlier models . Install 5/16 in. star washers (5) and 5/16-18 x 3/4 in. buttonhead screws (1) into stock mount nuts. Torque to 17 ft-lbs (23 Nm). SOLOAND PILLION 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. Retain all hardware for later use. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider seat. 3. Road King standard models. Install stock seat mount bracket onto new solo seat using two screws saved in Step 2. Road King Classic Custom models. Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. 1999 and later Road King standard models . Secure the rear mount bracket with stock mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). 1998 and earlier Road King standard models . Install solo seat by sliding front of seat into holder bracket on bike. Secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm). Road King Classic Custom models . Mount Kit Number 52903-01 is required for installation. Install solo seat (7) by sliding front of seat into holder bracket on bike. • 1999 and later models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). • 1998 and earlier models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm)

Incoming search terms:

2005 HONDA CBR 600RR Superbike BRAKE LINES INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 03-01-2011

download
Step 1: Identify the key components that complete our Super bike KIT, you should have 2 lines (front Kit), and 1 Double banjo bolt and 2 lower adapters. There are also a total of 7 washers, 5 will be used, and 2 are spares. We ALWAYS strongly suggest having a professional mechanic install these brake lines, all other installations VOID warranty. Inspect your brake system after every race. Step 2: Cover the complete front end of the bike so that if any brake fluid does spill the paint will not be damaged, brake fluid will spill, there is no question!! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install onto the calipers the Galfer adapter, the course thread area threads to the caliper with one washer. Torque level is 12 to 13 ft pounds. (See picture on adapter A) Step 5: Install right and left lines to the master cylinder, the right line is the shortest out of the two lines. These lines will travel from the master cylinder to the calipers; a double banjo bolt is included to run two lines down. (Picture B). This is the sequence on the master cylinder: Master cylinder, washer, straight banjo (from right line), washer, 12 degree banjo (from left line) washer and double banjo hex. Double banjo bolt torque level is 12 FT Pounds . (For positioning see picture G). Banjo 12 on left line must be facing a bit more to the left than the straight banjo of right line, so that the lines can cross at lower triple clamp better. On the calipers, make sure that the 90-degree fittings are pointing out a little bit, thread banjo end to the adapter, torque the end to 6 ½ Ft pounds . (See pictures C, D, E) Before you begin bleeding process, please check for clearance of the lines, push on the front end down, see that the lines are not binding with anything and that when the front end is fully extended or fully under pressure the lines are traveling correctly and clear from any obstructions. Ones the lines have been check for clearance; the two lines are Zip tied together at the same level of the lower triple clamp area. (See pictures F), please make sure that lines cross each other. Step 6: Bleed system, conventional bleeding, pump and release the air from caliper bleed nipples… DOT 4-brake fluid is recommended.

Incoming search terms:

Harley Davidson FL series Electra Glide, Ultra Classic, Road King, Road Glide Left and Right Mounting Plate Installation Installation Manual

0

Filed Under (Harley Davidson) by admin on 25-02-2012

download
Remove existing control arm end cap and grind the outside flush. See picture below for reference. The swing arm will drop if both sides are removed at the same time. To ease installation, complete one side before starting on the other. Note: there is a left and right. Left and right end caps shown. 2. Install mounting plate assembly 10002351 on top of the end cap using 7/16″ hex head bolt and lock washer in the bottom hole. Use the 7/16″ counter sink bolt in the top hole. Make sure the end cap is seated properly. The end cap notch should fit into the recess on the frame. The pivot arm assembly is shipped on mounting plate assembly; you may remove the pivot arm to make installation easier. 3. Snug up the bolts evenly, make sure the end caps are not crooked in relation to the frame. Tighten both bolts to 25 ft lbs. (Further tightening will be required after the toe in is set). 4. If you removed the left hand pivot arm assembly, remount it now, 10002575-A (pg 20) with seal, bearings (2), washer, nut, cotter pin and dust cover. 5. Repeat for right hand side. 5 Toe In Adjustment Adjustment made with the mounting plates, bolts, pivot arms, and hubs (without wheels and tires) in place

Incoming search terms:

2003-2004 Honda CBR600RR FK003D348SB Superbike Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 25-01-2011

download
Step 1: Identify the key components that complete our Superbike kit: You should have 2 lines (front kit), 1 double banjo bolt and 2 lower adapters. There are also a total of 7 washers. 5 will be used, and 2 are spares. We strongly suggest having a professional mechanic install these brake lines; all other installations VOID warranty. Inspect your brake system after every race. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install the Galfer adapters onto the right and left calipers. Thread each adapter into the calipers with one washer, and torque at 12 to 13 ft pounds. (See picture S1) Step 5: Install the right and left lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt (see picture S2) is included to run two lines down. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, 12-degree banjo (from right line), washer, 12-degree banjo (from left line), washer, and double banjo hex. Double banjo bolt torque level is 12 FT Pounds. (See picture S3) Make sure that the 40-degree fittings on each caliper are pointing away from the bike just a little bit (see picture S4/S5 for right caliper and S6/S7 for left) . Thread each banjo end into the adapter, and torque to 6 ½ Ft pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Once the lines have been checked for clearance, we recommend using a zip-tie to bring the lines together about an inch above the lower triple clamp area

1994-2003 Suzuki GSXR750 and 1997-2004 Suzuki GSXR600 Superbike Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 10-01-2011

download
Step 1: Identify the key components that complete our Superbike kit: You should have 2 lines (front kit), 1 double banjo bolt and 2 lower adapters. There are also a total of 7 washers. 5 will be used, and 2 are spares. We strongly suggest having a professional mechanic install these brake lines; all other installations VOID warranty. Inspect your brake system after every race. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install the Galfer adapters onto the right and left calipers. Thread each adapter into the calipers with one washer, and torque at 12 to 13 ft pounds. (See picture S4) Step 5: Install the right and left lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt (see picture S5) is included to run two lines down. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, straight banjo (from right line), washer, 12-degree banjo (from left line), washer, and double banjo hex. Double banjo bolt torque level is 12 FT Pounds. ( See picture S6) Make sure that the 90-degree fittings on each caliper are pointing away from the bike just a little bit (see pictures S7 through S9 of calipers) . Thread each banjo end into the adapter, and torque to 6 ½ Ft pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Once the lines have been checked for clearance, we recommend using a zip-tie to bring the lines together about an inch above the lower triple clamp area. (Picture S10) Step 6: Bleed brake system according to owner’s manual, and build appropriate pressure. Finishing with DOT 4-brake fluid is recommended.

Incoming search terms:

2001 – 2004 Camry, Highlander, Solara & 2004

0

Filed Under (Toyota Manuals) by admin on 12-10-2011

download
2004 model year Camry, Highlander, Solara and 2004 model year RAV4 vehicles with the 2AZ-FE engine may exhibit squealing and/or rattling noises coming from the engine compartment during vehicle operation especially after a cold soak. The belt tensioner assembly has been improved to correct this condition. 2001 – 2004 model year Camry, Highlander and Solara vehicles equipped with 2AZ-FE engines produced BEFORE the Production Change Effective VINs shown below. 2004 model year RAV4 vehicles produced BEFORE the Production Change Effective VINs shown below. MODEL ENGINE LINE PRODUCTION CHANGE EFFECTIVE VIN TMMK Line 1 4T1BE3#K#4U358206 Camry TMMK Line 2 4T1BE3#K#4U914052 y 2AZFE Tsutsumi JTDBE3#K#40296732 Highlander 2AZ-FE TMK JTE#D2#A#40100501 Solara TMMK 4T1CE3#P#4U914074 RAV4 Tahara JTE#D2#V#40029797 PREVIOUS PART NUMBERCURRENT PART NUMBER PART NAME QTY 16620-28010 16620-28011 Tensioner Assembly, V-ribbed Belt 1 OP CODE DESCRIPTION TIME OFP T1 T2 EG8001 R & R Accessory Belt Tensioner 0.9 16620-28010 91 55 Applicable Warranty*: This repair is covered under the Toyota Comprehensive Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle’s in-service date. *Warranty application is limited to correction of a problem based upon a customer’s specific complaint

Incoming search terms:

Aprilia Falco Synchronizing the Cylinder Vacuum

0

Filed Under (Aprilia) by admin on 26-10-2010

download
Motorcycle cylinders work quite independently compared to automobiles. Separate carburation, intake manifolds, exhaust pipes and sometimes even independent air filters allow the cylinders to be tuned so that one may be making more power than another. This can be due to differences in air flow, temperature, injection, or valve adjustment betwen the cylinders. Periodically, the cylinders should be synchronized. This is usually done by comparing intake manifold vacuum beneath each throttle and trimming the mixture until balanced. Some old-timers will tell you it can be done by ear, listening to the air flow in each carb throat through a tube stuck in your ear. Most modern tuners have switched to mercury sticks. Rigid tubes stuck in a bath of mercury are attached to the vacuum source. The vacuum draws the mercury up the sticks in proportion to pressure difference between the manifold and the atmosphere. In order to smooth out the individual vacuum pulses, a damping device is needed. This is nothing more than a small orifice (pin hole) restriction in the lines, placed close to the manifold with an air reservoir (length of tube) behind it. Because there is no real air flow in the gauges, there is no pressure drop across the orifice. But when the manifold vacuum drops there is a delay before the gauge pressure can bleed off and it appears steady and readable. Other types of vacuum gauges include mercury-less versions (that draw metal rods), or traditional needle, or “clock” gauges. The clock gauges are very fast acting (they are designed that way so you can see engine problems such as sticking valves). You will definitely need a damper if you choose a clock gauge. I would recommend using two side by side gauges for checking cylinder synch. The reason is, the cylinders are not perfectly independent. As one cylinder drops strength, the idle drops, and this will change the vacuum in the second cylinder’s manifold. It takes a bit of fooling around to get a cause-and-effect feel when you are turning the screws. Swapping gauges would make this difficult

Incoming search terms:

2004-2007 HONDA CBR 1000RR Super bike Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Make sure to save the nut and bolt that are currently holding the stock lower section of the hoses. (See picture A) Step 4: Install the Galfer adapters onto the right and left calipers. Thread each adapter into the calipers with one washer, and torque at 12 to 13 ft pounds. Step 5: Install the right and left lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt is included to run two lines down. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, 40-degree banjo from right line, washer, 40-degree banjo from left line, washer, and double banjo hex. Double banjo bolt torque level is 12 FT Pounds. (For positioning see picture B) . Make sure that the 90-degree fittings on each caliper are pointing straight up (see picture C) . Thread each banjo end onto the adapter, and torque to 6 ½ Ft pounds. Please tighten the “C” clips on the fender using the OEM bolts we asked you to save above. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Once the lines have been checked for clearance, using the galfer 2line clip to bring the lines together and mounting it to the triple tree will insure proper clearness and routing. (See picture D) Step 6: Bleed brake system according to owner’s manual, and build appropriate pressure. Finishing with Galfer DOT 4- brake fluid is recommended.

2004 King 50 And CM 50 clutch cover alignment and securing technique

0

Filed Under (Cobra) by admin on 10-11-2010

download
Some 2004 King & CM models have a thicker (brown) clutch cover gasket that requires retightening of the cover bolts several times before they remain tight. Follow this procedure to properly align the kick start gears and clutch cover. You should do this if the kick lever is not engaging properly (high frequency of not engaging the engine when you attempt to kick start the bike) . NOTE : Proper clutch cover torque value is 70 in-lb (7.9 Nm). NOTE : Lay the bike on the left hand side, or drain the clutch lubricant from the bottom end before performing this procedure. Loosen the six clutch cover screws (5mm allen) enough that the clutch cover can be moved by hand. Engage the kick lever with your hand and stroke it half way down and stop holding pressure on the kick lever (see picture)

2004 King rear brake caliper carrier pad

0

Filed Under (Cobra) by admin on 10-11-2010

download
An adhesive backed rubber pad that acts as a cushion under the rear brake caliper carrier was absent from certain 2004 King models. The pads are available from Cobra and should be applied to the bottom surface of the brake carrier that mates against the top of the swingarm.

Incoming search terms: