2004 suzuki marauder spark plug gap

You search Auto repair manual PDF 2004 suzuki marauder spark plug gap, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2004 suzuki marauder spark plug gap Direct Download speed 5282 Kb/s

  2004 suzuki marauder spark plug gap Full Version speed 6162 Kb/s



SUZUKI SV1000 PERIODIC MAINTENANCE

0

Filed Under (Suzuki) by admin on 26-02-2011

download
MAINTENANCE AND TUNE-UP PRO- CEDURES This section describes the servicing procedures for each item of the Periodic Maintenance requirements. AIR CLEANER I Inspect every 6 000 km (4 000 miles, 6 months) and replace every 18 000 km (11 000 miles, 18 months) . • * Remove the seat. (LF6-7) • * Lift and support the feul tank . (C-74-65) • * Remove the air cleaner box cap O. • * Remove the air cleaner element O. • * Carefully use air hose to blow the dust from the cleaner ele- ment. CAUTION Always use air pressure on the throttle body side of the air cleaner element . If air pressure is used on the other side, dirt will be forced into the pores of the air cleaner element thus restricting air flow through the air cleaner element . PERIODIC MAINTENANCE 2-5 2-6PERIODIC MAINTENANCE • * Reinstall the cleaned or new air cleaner element in the reverse order of removal . CAUTION If driving under dusty condition, clean the air cleaner element more frequently. The surest way to accelerate engine wear is to use the engine without the element or to use a ruptured element. Make sure that the air cleaner is in good condition at all times. Life of the engine depends largely on this component! NOTE: When cleaning the air cleaner element, drain water from the air cleaner by removing the drain plug . SPARK PLUG Inspect every 6 000 km (4 000 miles, 6 months) and replace every 12 000 km (7 500 miles, 12 months) . No. 1 (FRONT) SPARK PLUG REMOVAL • * Remove the radiator mounting bolt O. • * Move the radiator forward. • * Remove the spark plug cap O. NOTE: Be careful not to damage the radiator fins . A WARNING The hot radiator and the hot engine can burn you . Wait until the radiator and the engine are cool enough to touch . • * Remove the spark plug with a spark plug wrench. 1 6 I It No. 2 (REAR) SPARK PLUG REMOVAL • * Remove the seat. (r–,-6-7) • * Lift and support the fuel tank . (=4-65) 4-65) • * Disconnect the camshaft position sensor 1O and breather hose (Z. • * Remove the rubber heat shield ® . • * Remove the spark plug cap . • * Remove the spark plug with a spark plug wrench . HEAT RANGE • * Check to see the heat range of the plug . CARBON DEPOSIT •Check to see if there are carbon deposits on the plugs . If carbon is deposited, remove it with a spark plug cleaner machine or carefully using a tool with a pointed end . SPARK PLUG GAP • * Measure the plug gap with a thickness gauge . If out of specification, adjust it to the following gap . 09900-20803 : Thickness gauge Spark plug gap OA Standard: 0.6 – 0 .7 mm (0.024 -0.028 in) ELECTRODES CONDITION •Check to see the worn or burnt condition of the electrodes . If it is extremely worn or burnt, replace the plug . And also replace the plug if it has a broken insulator, damaged thread . CAUTION Confirm the thread size and reach when replacing the plug. If the reach is too short, carbon will be deposited on the screw portion of the plug hole and engine damage may result

Incoming search terms:

SANYANG HD 125/ 200 Specifications And SERVICE MANUAL

0

Filed Under (Sym) by admin on 24-11-2010

download
heck and adjustment Fault condition Probable causes Loosen carburetor drain bolt to check if there is gasoline inside the carburetor Fuel supplied tom carburetor sufficient No fuel is supplied to carburetor Remove spark plug, install it into spark plug cap, and perform a spark test against engine ground. Perform cylinder compression pressure test. Check if sparks Weak sparks, no spark at all Low compression pressure or no pressure Re-start by following the starting procedures No ignition There are some signs of ignition, nut engine can not be started Remove the spark plug again and check it. Remove carburetor after 30 minutes and connect a hose onto fuel rich circuit. Then blow the hose with air Dry spark plug Wet spark plug Blowing in normal Blowing clogged 1. No fuel in fuel tank 2. Check if the pipes, fuel tank to carburetor and intake vacuum, are clogged. 3. Float valve clogged 4. Lines in fuel tank evaporation system clogged 5. Malfunction of fuel pump 6. Loosen or damaged fuel pump vacuum hose 7. Fuel filter clogged 1. Malfunction of spark plug 2. Spark plug foul 3. Malfunction of CDI set 4. Malfunction of AC generator 5. Ignition coil is in open or short circuit 6. Ignition coil leads open or short circuit 7. Malfunction of main switch 1. Piston ring seized 2. Malfunction of cylinder valves 3. Worn cylinder and piston ring 4. Cylinder gasket leak 5. Sand hole in compression parts 1. Malfunction of throttle valve operation 2. Air sucked into intake manifold 3. Incorrect ignition timing 1. Fuel level in carburetor too high 2. Malfunction of throttle valve operation 3. Throttle valve opening too wid

1994-2003 Suzuki GSXR750 and 1997-2004 Suzuki GSXR600 Superbike Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 10-01-2011

download
Step 1: Identify the key components that complete our Superbike kit: You should have 2 lines (front kit), 1 double banjo bolt and 2 lower adapters. There are also a total of 7 washers. 5 will be used, and 2 are spares. We strongly suggest having a professional mechanic install these brake lines; all other installations VOID warranty. Inspect your brake system after every race. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install the Galfer adapters onto the right and left calipers. Thread each adapter into the calipers with one washer, and torque at 12 to 13 ft pounds. (See picture S4) Step 5: Install the right and left lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt (see picture S5) is included to run two lines down. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, straight banjo (from right line), washer, 12-degree banjo (from left line), washer, and double banjo hex. Double banjo bolt torque level is 12 FT Pounds. ( See picture S6) Make sure that the 90-degree fittings on each caliper are pointing away from the bike just a little bit (see pictures S7 through S9 of calipers) . Thread each banjo end into the adapter, and torque to 6 ½ Ft pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Once the lines have been checked for clearance, we recommend using a zip-tie to bring the lines together about an inch above the lower triple clamp area. (Picture S10) Step 6: Bleed brake system according to owner’s manual, and build appropriate pressure. Finishing with DOT 4-brake fluid is recommended.

Incoming search terms:

2001 – 2004 Camry, Highlander, Solara & 2004

0

Filed Under (Toyota Manuals) by admin on 12-10-2011

download
2004 model year Camry, Highlander, Solara and 2004 model year RAV4 vehicles with the 2AZ-FE engine may exhibit squealing and/or rattling noises coming from the engine compartment during vehicle operation especially after a cold soak. The belt tensioner assembly has been improved to correct this condition. 2001 – 2004 model year Camry, Highlander and Solara vehicles equipped with 2AZ-FE engines produced BEFORE the Production Change Effective VINs shown below. 2004 model year RAV4 vehicles produced BEFORE the Production Change Effective VINs shown below. MODEL ENGINE LINE PRODUCTION CHANGE EFFECTIVE VIN TMMK Line 1 4T1BE3#K#4U358206 Camry TMMK Line 2 4T1BE3#K#4U914052 y 2AZFE Tsutsumi JTDBE3#K#40296732 Highlander 2AZ-FE TMK JTE#D2#A#40100501 Solara TMMK 4T1CE3#P#4U914074 RAV4 Tahara JTE#D2#V#40029797 PREVIOUS PART NUMBERCURRENT PART NUMBER PART NAME QTY 16620-28010 16620-28011 Tensioner Assembly, V-ribbed Belt 1 OP CODE DESCRIPTION TIME OFP T1 T2 EG8001 R & R Accessory Belt Tensioner 0.9 16620-28010 91 55 Applicable Warranty*: This repair is covered under the Toyota Comprehensive Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle’s in-service date. *Warranty application is limited to correction of a problem based upon a customer’s specific complaint

Incoming search terms:

Honda CG125 Owners Workshop Manual

0

Filed Under (Honda) by admin on 25-11-2010

download
Clean the air filter Pull off the right-hand side panel and remove the two nuts which secure the air filter cover. Withdraw the cover, checking that the sealing gasket is in good condition, pull out the retaining spring and withdraw the element assembly. Peel off the inner and outer foam sleeves. Wash all components in white spirit (Stoddard solvent) or in warm water and detergent and dry them thoroughly. Soak the foam sleeves in the specified oil, then squeeze them gently (do not wring them out or they will be damaged) to expel all surplus oil. Refit the sleeves to the element frame. On reassembly ensure that all components are correctly fitted so that unfiltered air cannot bypass the element. 2 Check the spark plug Remove the spark plug cap, unscrew the plug and check its condition, comparing it with the photographs on page 65. If it is badly worn or fouled it must be renewed. If it is fit for further service check the gap and reset it if necessary, as described in Chapter 3.8. 3 Check the valve clearances It is important that the correct valve clearance is maintained. A small amount of free play is designed into the valve train to allow for expansion of the various components. If the setting deviates greatly from that specified, a marked drop in performance will be evident. In the case of the clearance becoming too great, it will be found that valve operation will be noisy, and performance will drop off as a result of the valves not opening fully. If on the other hand, the clearance is too small the valves may not close completely. This will not only cause loss of compression, but will also cause the valves to burn out very quickly. In extreme cases, a valve head may strike the piston crown, causing extensive damage to the engine. The clearances should be checked and adjusted with a cold engine. Place the machine on its centre stand and remove the rocker cover, taking care not to damage the 0 ring. Remove the gearchange pedal and the left-hand outer cover to expose the generator rotor. Remove plug and allow old oil to drain Remove the spark plug, then slowly rotate the engine anticlockwise by way of the generator rotor, watching the inlet valve. When it has opened and closed again (sunk down and risen up to its original position), rotate the engine further until the T mark on the rotor periphery aligns exactly with the raised index mark which is positioned between 12 and 1 o’clock (from the crankshaft) on the generator stator. The engine will then be in the correct position for checking the valve clearances, namely at Top Dead Centre (TDC) on the compression stroke; check that there is free play at both rockers. Using a 0.08 mm (0.003 in) feeler gauge, check the clearance between the top of each valve stem and its corresponding rocker. The feeler gauge must be a light sliding fit, with the rocker and valve stem just nipping it. If necessary, slacken the locknut, and turn the small square-headed adjuster to obtain the correct setting. Tighten the locknut, holding the adjuster at the same time to prevent it from moving. Finally, recheck the setting and then repeat the procedure on the other rocker. 4 Check the contact breaker points and ignition timing Note: since the generator stator plate is located by its countersunk retaining screws, the ignition timing can only be altered by opening or closing the contact breaker gap; therefore both operations are described as one. The full procedure is given here for ease of reference, but if the points are found to be in good condition and if the gap has not altered or is within the tolerance, then the ignition timing will be sufficiently accurate and there will be no need to carry out the full check. First remove the gearchange pedal, the left-hand outer cover, the spark plug and the left-hand side panel

Honda VT1100 Shadow Guide Plug Patch Repair Manual

0

Filed Under (Honda) by admin on 24-04-2011

download
Find the guide plug.bn The guide plug is shown in the shop manual with the engine removed from the frame and the left crankcase cover removed. (You’ll find this illustration in the “ELECTRIC STARTER/STARTER CLUTCH” chapter in the “STARTER DRIVEN GEAR/STARTER CLUTCH REMOVAL” section.) It’s a little bit harder to find it on the bike. Start by following the yardstick to see where the guide plug is on my bike. To find it on your bike, lie on the ground (or, preferably a mechanics creeper) next to the bike (without the yardstick) and peek under the shift lever and over the frame There it is, just barely visible from the side of the bike. Here’s what a new one looks like: 2. Clean the guide plug and crankcase. From the front of the bike, clean the guide plug and crankcase with brake cleaner in a VERY focused spray. Let the cleaner evaporate before moving to the next step. Page 4 Rev: Draft 5/20/2007 Page 4 of 5 3. Reposition the guide plug. a. From the side of the bike, use the yardstick (or a long screwdriver if you prefer) to gently push the guide plug back into the crankcase. (Note the JB Weld from the previous patch operation.) b. From the front of the bike, gently push upward on the bottom of the upper tab (as shown below) or the bottom of the forward tab to rotate the guide plug into the proper position while maintaining pressure with the yardstick

Incoming search terms:

HARLEY DAVIDSON GLOSS BLACK HEAD BOLT COVERS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
This kit fits 1992 and later Evolution 1340 and XL models and 1999 and later Twin Cam-equipped models. INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. Remove spark plugs. 2. See Figure 1. Install head bolt covers (1), on head bolts (3), secure using setscrew (2) and Allen wrench included with kit. To prevent setscrews from falling into the spark plug holes, start threading the setscrews into the covers before placing them over the head bolts. Position cover on head bolt so that when spark plug is reinstalled setscrew is hidden from view but accessible with Allen wrench. Do not tighten setscrews on high points of bolts. 3. Reinstall spark plugs. Tighten spark plugs to 11-18 ftlbs (15-24 Nm) . If a torque wrench is not available, finger- tighten spark plug and then, using a spark plug wrench, tighten plug an additional 1/4 turn. 4. Readjust setscrew tightness after motor has operated at full operating temperature and then cooled. 2 1 3 is 001586 1. Head bolt cover 2. Setscrew 3. Head bolt Figure 1. Head Bolt Cover Installation

Incoming search terms:

HONDA CB650/ 750F/ 900F/ 1100F/ GL1100 Spark Unit Set Installation Manual

0

Filed Under (Honda) by admin on 05-04-2011

download
INSTALLATION INSTRUCTIONS: 1. All connections must be of the highest quality, use crimped or soldered connections; twisted wires will not give a satisfactory operation. 2. Remove the seat and/or petrol tank to gain access to the original spark units (if fitted); these are normally fitted under the seat between the top frame tubing. Each of these units consists of a small alloy metal box with sleeved wires terminated by a small connector (coupler). They also have a mounting tab with a single fixing hole. 3. On four cylinder machines there will be two units, normally mounted back to back; one for cylinders 1&4 and one for cylinders 2&3. 4. For safety, disconnect the battery. 5. Unplug the couplers from each of the units. Undo the fixings and remove the units. 6. Fit the new spark units in the place of the old ones or find a suitable alternative, close to the connectors. Secure the units to the frame or mounting platform using the supplied tie-straps and adhesive mounting base (if required). If required, a thin sheet of rubber or double-sided tape can be used to keep the units in position. Do not completely wrap the units in foam rubber. 7. Push the wiring harness plugs into the new spark unit socket connectors; they will only fit one way. Reconnect the battery. 8. If you are rewiring the machine or do not have the standard wiring harness, the spark unit wire colours & functions are as follows: GREEN Ö GROUND (0 VOLTS) BLACK/WHITE Ö IGNITION SUPPLY (+12 VOLTS) VIA ENGINE STOP SWITCH YELLOW Ö IGNITION COIL OUTPUT (TO COIL —) WHITE Ö PULSE GENERATOR (WHITE RING) BLUE Ö PULSE GENERATOR (UNMARKED) There are two pulse generators, one for cylinders 1&4 and one for cylinders 2&3. The left hand one is normally for cylinders 1&4 (see fig.1). There are two wires of the same colour coming from each pulse generator, one of these wires is normally marked with a white band. The pulse generator wire with the white band connects to the white wire from the corresponding spark unit, the other pulse generator wire connects to the blue wire on the corresponding spark unit. If the white band is missing, this is normally the upper wire coming from the pulse generator. 9. Refit the seat and tank (if removed earlier). 10. Fitting is now complete, although for best results you may wish to verify the ignition timing, see the following guide

Incoming search terms:

SUZUKI VZ800 MARAUDER SLIP-ON EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosenthe right hand side footrest assembly. 2. Loosenthe two head pipes at the cylinder head. 3. Loosen the muffler clamps, located on the inlet end of the mufflers. 4. Remove the two nuts that mount the lower muffler to motorcycle. Keep the two mufflers bolted together as an assembly. 5. Lift the muffler assembly up to clear the studs from the mounting holes. Pull the mufflers off the head pipes and set them aside. 6. Remove the two flanged steel spacers from the hole in the rubber cushions, where the stock muffler assembly mounted. Reinstall the steel spacers through the backside of the rubber cushions so the flanged end of the spacers are on the backside of the cushions, opposite of there original position. 7. Remove the rear most heat shields from both of the head pipes and set them aside. 8. Remove the stock exhaust gaskets from the ends of both pipes. The Vance & Hines slip-on does not use a gasket at the slip joint . 9. Install the new muffler mounting bracket (stamped with the # 233 ) to the front side of the two holes with the rubber cushions the two of the 5/16″x 1 1/4″ bolt and two 5/16″ lock nuts (hardware supplied) through the two holes in the bracket that are spaced farthest apart. When mounted correctly, the bracket should bend up and out from the motorcycle

Incoming search terms:

SUZUKI MOTORCYCLES Gsxr 600, Gsxr 750, Gsxr 1000 teak the lead

0

Filed Under (Suzuki) by admin on 12-11-2010

download
The launch of the sixth generation of Gsxr marked a shift in Suzuki’s emphasis on two fronts. One, the Gsxr 1000 now took the upper hand in the development stakes. Historically, the Gsxr 750 led the march-arriving first, gaining the most recent technology, absorbing the lion’s share of corporate pride-but by 2003 the Gsxr 1000 was in the lead. Two, the Gsxr 1000 represents another, more subtle shift for Suzuki engineering, in which the designers-the lucky guys who get to clothe these amazing machines-have more freedom of expression. With this generation, the designs turned edgier, sharper, more aggressive looking than ever. What’s more, the Gsxr 1000 K3 would be the proving ground for a host of changes brought to the Gsxr 600 and Gsxr 750 for 2004. In fact, nearly every upgrade to the smaller bikes appeared on the Gsxr 1000 a year before. But the real impetus for driving the Gsxr 1000 to the head of development and, indeed, shortening its development cycle was competition both on the track and in the showroom. For the track, it was understood that Superbike racing would revert to allowing 1000 cc four-cylinder bikes in place of the 750s that had been the limit since 1982. In 2002, Yoshimura and Mat Mladin barely lost the AMA Superbike crown to Nicky Hayden aboard the Honda RC5!. But it would be the RC’s swan song of competitiveness with the change to 1000 cc fours. To keep speeds in check, the AMA Superbike rules would require 1000 cc fours to have some additional limitations compared to the twins and triples. For example, “Cylinder heads may be ported and machined, but altering of valve angles will not be permitted; aftermarket valves, springs, retainers, and other valve-train components will be permitted; valves must be stock size and same basic material as original equipment; aftermarket camshafts will be permitted, but earn lift and resulting valve lift must be no greater than stock. “In addition, the “stock crankshaft must be retained, The only allowable modifications are balancing, polishing of bearing surfaces and attachment of accessory drives. Homologated transmission gear sets (one optional set of ratios per approved model) will be permitted. Optional sets will be price-controlled and must be available to any legitimate AMA Superbike competitor. Homologated fuel-injection throttle-body assemblies (one optional type per approved model) and aftermarket airboxes will be permitted. Modifications to throttle bodies will not be permitted. Optional throttle bodies will be price-controlled and must be available to any legitimate AMA Superbike competitor.” The thinking was simple: keep the liter bikes from sucking through massive throttle bodies, and the horsepower might not (and, it was hoped, would not) go through the roof. In preparation for racing, Suzuki moto wanted to make a host of small changes to the Gsxr 1000, but its motivation was also to keep the bike at the forefront of open-class street bikes. Suzuki engineers knew that Honda and Kawasaki were readying all-new models-the CBR 954 RR and the ZX 9 R had long since been vanquished-and rumor had it that Yamaha was ready with yet another push with the R1.It was the right time to make alterations to the Gsxr 1000. Heading the list was, as one might expect, a revised engine.

Incoming search terms:

Incoming search terms: