2004 yamaha raptor 350 rear fender for sale

You search Auto repair manual PDF 2004 yamaha raptor 350 rear fender for sale, if there are search results will appear below. If search results do not exist, please search by others keyword.





HARLEY DAVIDSON FRONT AND REAR FENDER TIP TRIM INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
Installation GENERAL The original equipment (stock) fender tip lamp assemblies must be removed and the wire(s) must be unplugged or removed as specified in the following instructions. FRONT FENDER TIP REMOVAL OF STOCK FRONT FENDER TIP LAMP ON 1994 AND LATER FLT MODELS 1. Refer to the applicable FLT Service Manual. Remove headlamp assembly with housing. 2. Locate the 3-place connector [32 in wiring diagram] through which 12vdc and electrical ground are connected to the fender tip lamp assembly. The connector locations are as follows: FLTC Ultra: Under fuse and circuit breaker block FLHT/C/C-U: On bottom of left outer fairing bracket FLHR: On left front above air suspension valve NOTE Before disassembling the connector in the next step, refer to the applicable wiring diagram and check wire colors and connections to assure that connector [32] has been located. 3. Refer to the “DEUTSCH ELECTRICAL CONNECTOR” section in the FLT Service Manual and remove the leads, connected to the fender tip lamp, from the socket half, connector [32B]. 4. Insert a small screwdriver blade in rectangular slot at top center of fender tip lamp lens and gently pry lens from lamp. 5. Remove two screws and nuts that fasten fender tip lamp assembly to front fender. Gently remove the lamp assembly taking care not to damage wires connected to lamp assembly. 6. Reach under left side of fender and gently pull wires through rear hole in left side of fender and then through clips on left side of fender and finally through front hole and out of trim strip. REMOVAL OF STOCK FRONT FENDER TIP LAMP ON 1993 AND EARLIER FLT MODELS, FLSTC AND FLSTN 1. Insert a small screwdriver blade in rectangular slot at top center of fender tip lamp lens and gently pry lens from lamp. 2. Remove two screws and nuts that fasten fender tip lamp assembly to front fender. Gently remove the lamp assembly taking care not to damage wire connected to lamp assembly. 3. Unplug wire connector located about 3 in. from lamp assembly. Cover the socket half of connector (connected to motorcycle wiring) with electrical tape. INSTALLING FRONT FENDER TIP TRIM FROM KIT-ALL MODELS 1. Position fender tip trim over holes in fender and guide outer ends of fender tip trim into trim strips on sides of fender. 2. Insert studs on fender tip trim through holes in fender and secure with locknuts included in kit. Tighten locknuts to 6 in-lbs . REAR FENDER TIP REMOVAL OF STOCK REAR FENDER TIP LAMP ON ALL MODELS Follow steps 1 through 3 given above for “1993 AND EARLIER FLT MODELS, FLSTC & FLSTN” INSTALLING REAR FENDER TIP TRIM FROM KIT-ALL MODELS 1. Position fender tip trim over holes in rear fender. 2. Insert studs on fender tip trim through holes in fender and secure with locknuts included in kit. Tighten locknuts to 6 in-lbs

HARLEY DAVIDSON HERITAGE REAR FENDER RAIL DISASSEMBLY AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-02-2011

download
DISASSEMBLY NOTE See Figure 1. Saddlebags must be removed to insert spacer (1). 1. Using a small flat head screw driver, remove rear fender tip light lens cover (A) by gently prying cover away from assembly. (There is a notch at top of cover to ease removal.) Remove and retain cover (A) and gasket (C). 2. Remove fender tip light assembly (B) by removing two screws, four star washers, and two nuts (not shown) using a #2 Phillips screw driver and a 3/8 inch wrench. Retain all hardware for reassembly. 3. Remove hole plugs from rearmost fender strut holes on both sides of fender. 4. Mark fender on both sides of bike using rear most fender strut hole as a template. Do not contact tire with drill bit when drilling fender holes. Drill bit contact with tire can lead to premature tire failure, which could result in death or serious injury. (00403f) 5. Carefully remove fender strut and drill a 11/32 inch hole through each side of fender in locations marked in Step 4. 6. Loosely reinstall fender strut (D), allowing enough room to slip spacer (1) between fender (E) and strut. INSTALLATION 1. Align rear fender rail (2) from kit with rearmost fender strut (D) mounting holes, making sure lower mounting tab (3) is inside fender (E). Place large chrome washer (4) from kit next to head of button head socket bolts (5) from kit. Insert bolt through fender rail (2), fender strut (D), spacer (1) and fender (E), in that order. Install large unfinished washer (6) from kit onto end of bolt (5). Secure assembly into place by threading locknuts (7) from kit onto ends of bolts (5) from inside of fender (E). Tighten loosely at this time. 2. Install truss head screw (8) from kit through fender (E) and rear fender rail mounting tab (3). Secure into place using small washer (9) and locknut (10) from kit. Use #2 Phillips screwdriver and a 3/8 inch wrench to tighten rear mounting assembly securely. 3. Tighten fender strut bolts (5) to 21-27 ft-lbs.(28-37 Nm) 4. Reinstall fender tip light assembly (B), gasket (C) and lens (A) using original hardware (not shown)

Incoming search terms:

HARLEY DAVIDSON HERITAGE CHROME FRONT FENDER RAIL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
INSTALLATION NOTE See Figure 1. Be careful not to crack plastic fender lamp lens (2) or chrome plate when removing lens. 1. Remove fender lamp light lens (2) by placing screwdriver in slot in top of lens and carefully prying cover loose. Retain lens and gasket for later installation. 2. Loosen four hex socket head screws (1) which attach fender (4) to fender mount. 3 2 4 1 is03805 1. Fender mount screws (4) 2. Fender lamp light lens 3. Fender Rail 4. Fender Figure 1. Installed Front fender Rail NOTE When installing fender rail (3), be sure fender rail supports are inside of fender. 3. Place fender rail (3) from kit into position, aligning the front bracket hole of rail with hole in front of fender (4). Fender rail supports will fit snugly inside fender. NOTE Be careful not to damage the fender lamp wire when securing front fender rail into place. 4. Use a magnet to place a 10-32 x 1/2 inch phillips screw through the hole in front fender and through front bracket hole of fender rail (3). 5. Loosely secure fender rail (3) to fender (4) with 1/2 inch flat washer and hex locknut. 6. On right side only, remove two hex socket head screws and nuts. Retain nuts for installation. 7. Replace original two socket head screws with 5/16-18 x 2 inch screws from kit. 8. For vehicles without caliper/rotor covers: On left side of fender (4) only, install a washer between rail (3) and fender for both screws. Replace original two hex socket head screws with 5/16-18 x 2 inch screws from kit. For vehicle with caliper/rotor covers: Do not replace hex socket head screw that supports caliper/rotor cover. On left side of fender (4), install a washer between fender (4) and rail (3) on screw that does not support the caliper/rotor cover (towards the front of the vehicle). Replace remaining hex socket head screw with 5/16-18 x 2 inch screw from kit. 9. Install four original nuts. 10. Tighten front bracket Phillips screw securely. Tighten four hex socket head screws to 14-18 ft-lbs (19-24 Nm). 11. Install gasket and fender lamp lens removed earlier

HARLEY DAVIDSON FLSTS MUD FLAP KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-02-2011

download
Installation For installation on rear fender with marker light: 1. Cut out Rear Fender Template. 2. Use a paper punch to punch out holes marked A and C . Holes A are the locations of the marker light screws, and hole C is the location of the marker light wiring. Cut along centerline of template from top down to hole C . 3. Remove light lens by carefully pressing down on top center of light to disengage tab. 4. Remove the two screws, washers, and nuts that hold the marker light assembly in place and carefully pull the light assembly away from the fender. Disconnect the wire connector and remove the light assembly. 5. Slip template over marker light wires, align holes marked A with marker light holes, and align lower edge of template with lower edge of fender. Tape template in place. 6. Prick punch holes marked B at indicated centers on template. 7. Carefully, and as accurately as possible, drill holes marked B in two steps. First drill holes with a 1/16″ drill, then finish holes with a 7/32″ drill. 8. See Service Parts illustration. Place the mud flap and reinforcement inside fender and secure outer holes with buttonhead screws (3), washers (6), and locknuts (7) contained in kit. The mud flap is split to fit around light assembly wires. 9. Using the longer panhead screws provided in the kit, install fender tip light and check that light is operational. For installation on rear fender without marker light: 1. Using a high quality masking tape, mask the lower three inches of the middle of the fender for the purpose of drawing a centerline on the fender. 2. Using a machinist’s square, locate the centerline of the fender by measuring in from each side of the fender flats. Mark the centerline on the masking tape. 3. Cut out Rear Fender Template. 4. Align centerline of template with centerline drawn on fender. Align lower edge of template with lower edge of fender. Tape template in place. 5. Prick punch holes marked B and C at indicated centers on template. 6. Carefully, and as accurately as possible, drill holes marked B and C in two steps. First drill holes with a 1/16″ drill, then finish holes with a 7/32″ drill. 7. See Service Parts illustration. Place the mud flap and reinforcement inside fender and secure with buttonhead screws (3), washers (5 and 6), and locknuts (7) contained in kit. For installation on front fender (FLSTS only): 1. Using a high quality masking tape, mask the lower three inches of the middle of the fender for the purpose of drawing a centerline on the fender. 2. Using a machinist’s square, locate the centerline of the fender by measuring in from each side of the fender flats. Mark the centerline on the masking tape. 3. Cut out Front Fender Template. 4. Align centerline of template with centerline drawn on fender. Align lower edge of template with lower edge of fender. Tape template in place. 5. Prick punch holes at indicated centers on template. 6. Carefully, and as accurately as possible, drill holes marked in two steps. First drill holes with a 1/16″ drill, then finish holes with a 7/32″ drill. 7. See Service Parts illustration. Place the mud flap and reinforcement inside fender and secure with buttonhead screws (3), washers (5 and 6), and locknuts (7) contained in kit

Incoming search terms:

Harley Davidson Road Rod Saddle Bag System Kit INSTALLATION Instructions

0

Filed Under (Harley Davidson) by admin on 16-04-2012

download
Use locktite on all fasteners!! 2. Put bike on lift and place jack under frame. Raise bike to lift rear wheel. 3. If swing arm pivot shaft is drilled and tapped on each end, they need to be redrilled and tapped to 3/8-16 to a depth of _” deep. If you are unable to drill & tap your swing arm pivot shaft, you can purchase one from Cycle Visions (part #CV6121), See Harley Davidson® V-Rod® Service Manual Section 2, Page 2.89 for removal and installation instructions. 4. Remove seat, passenger seat, turn signal module, rear fender cover, turn signal license plate assembly, and rear foot peg assemblies. NOTE: Our bag system will not work with stock exhaust system… we recommend the 2-into-1 Supertrap, or you may use any exhaust system that is lower than the rear axle bolt. 5. Remove the two upper shock bolts. Relocate the shock spacer from the right side to the left side, and use the new spacer supplied on the right side. 6. Install front bag mount between frame and spacer (see Figure 1), reinstall shock bolts and torque to 31-50 lbs. 7. Install lower bag support frame to swing arm pivot shaft using the 3/8″ bolt through rear foot peg clevis and cover (see in Figure 2). NOTE: There is a right and left covers and bag support, install accordingly. Torque to 35 foot lbs. 8. Install rear fender front mounting tabs using 8mm 1.25 x _ and flat washers (supplied in kit) (see Figure 3). 9. Install upright saddlebag support brackets to the lower bag mount assembly and lower fender extension crossover mount. (see Figure 4). Torque to 25 lbs. NOTE: Install crossover mount with gusset facing down. 10. Remove license plate light from your rear turn signal bracket license plate assembly. Install license plate light on our license plate light bracket (see Figure 5). 11. Install the license plate bracket on the inside of the rear fender extension using the top holes of the license plate frame (see Figure 6 & 7). 12. Install fender washers on the inside of the fender extension (see Figure 8). 13. Install upper fender bracket to rear fender extension with a _-20 bolt supplied in kit (see Figure 9). 14. Install rear fender extension with chrome button fitted bolts. (see Figure 10 & 11). 15. To check alignment and fit of rear fender extension reinstall original rear fender. Once you have everything lined up and fitted, remove original rear fender, drill & tap (2) two 5/16 x 18 holes in rear fender support bracket (see Figure 12). 16. Install Harley Davidson® Part #70909-95 and 47449-97 bracket and receptacle on front and rear bag supports (see Figure 13 & 14). 17. Install Harley Davidson® Part #47449-97 bracket with receptable (see Figure 14). Make sure the bolts come from the inside out. This bracket is adjustable for location.

HARLEY DAVIDSON FLSTF TURN SIGNAL RELOCATION KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL 1. Remove seat according to the instructions in the Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. See Figure 1. Disconnect battery cables, negative (-) cable first. 2 1 is03242 1. Negative (-) cable 2. Tail lamp connector Figure 1. Negative Battery Cable and Tail Lamp Connector 3. See Figure 2. Remove two screws and tail lamp lens (1) from base (2). 2 1 is03243 1. Tail lamp lens 2. Tail lamp base Figure 2. Remove Tail Lamp Lens 4. See Figure 3. Using a Terminal Pick Tool (1), depress locking tabs and disconnect turn signal connectors (2- place) (2, 3) from circuit board. 5. Feed turn signal wiring and connector through opening in circuit board assembly and into rear wheel area. 6. See Figure 4. Remove turn signal wiring (1, 2) from clips (3) under rear of fender INSTALLATION NOTE Proper installation of kit requires that tasks be completed for one side of the motorcycle first before continuing to the opposite side. Route Turn Signal Wiring Through Rear Fender and Support 1. See Figure 5. Remove three rear screws (1) from fender support (2). 2. Loosen, but do not remove two front screws (3) from fender support. 1 3 2 is03285 1. Screw, rear (3) 2. Fender support 3. Screw, front (2) Figure 5. Fender Support Screws and Fender Support 3. Pull fender support away from rear fender to gain access to turn signal mount. 4. Remove stock screw and washer from turn signal mount. 5. See Figure 7. Pull turn signal (B) and turn signal mount (A) away from fender support. 6. Remove turn signal and wires from vehicle by routing turn signal wiring and connector through holes in rear fender and fender support. Gently guide wires through holes to ensure they do not get damaged. Feed Wiring and Install Relocation Bracket 1. See Figure 6. Feed turn signal wiring and connector through middle hole in turn signal relocation bracket and under rear of fender support. 1 is04635 1. Wire harness Figure 6. Wire Harness Routing 2. See Figure 7. Insert stock screw and washer through rear hole of relocation bracket (1) and turn signal mount (A). 3. Thread screw into turn signal (B). Tighten to 12-16 ft-lbs (16.3-21.7 Nm). 4. Align relocation bracket (1) with rear of fender support and install with screw (2) and nut (3) from kit. Tighten nut to 12-16 ft-lbs (16.3-21.7 Nm). Complete Turn Signal Relocation Wiring 1. See Figure 5. Install one rear screw (1) to hold fender support in place while routing wiring. Install screw snugly but do not fully tighten

HARLEY DAVIDSON VRSC SADDLEBAG SUPPORT KIT (WIDE TIRE) REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
REMOVAL Remove Pillion and Rear Fender NOTE If possible, lift the rear of the motorcycle up so the rear wheel drops to the bottom of shock travel. This will help provide clearance between the rear tire and fender when installing the mounting brackets. 1. Open the rider seat. 2. See Figure 1. Remove rider seat post (1), nut (2), and washer (3) from passenger pillion. Slide grabstrap (4) forward off pillion. Save mounting hardware for kit installation. 3. Push passenger pillion forward to release slot on bottom of pillion from post on fender tongue. 4. See Figure 2. Lift pillion up to remove lanyard (1) from hole in center of passenger pillion (2). Then lift pillion away from motorcycle. 5. Disconnect turn signal and tail light electrical connections from back of rear electrical caddy. Note position for later installation. 6. See Figure 3. Unsnap rear electrical caddy (1) from rear inner fender. 7. Remove and save two fender support bolts (2), washers (3), and grabstrap (4) from rear fender. 1 2 3 4 is03548 1. Rider seat post 2. Nut 3. Washer 4. Grabstrap Figure 1. Passenger Pillion and Mounting 2 1 3 i03571 1. Seat lanyard 2. Hole in pillion 3. Passenger pillion Figure 2. Seat Lanyard and Passenger Pillion 8. Remove four remaining fender support bolts (2) and washers (3) near center of rear fender. 9. Remove rear fender from vehicle. 3 2 4 2 3 2 3 1 is03544 1. Rear electrical caddy 2. Fender support bolt (6) 3. Washer (6) 4. Grabstrap Figure 3. Grabstrap, Rear Electrical Caddy, and Fender INSTALLATION Install Attach/Release Weldment, Rear Fender, and Grabstrap NOTE Apply Loctite 243 (blue) to last four threads of leave-on bracket screws. 1. See Figure 4. Install leave-on bracket (1) to outside surface of inner fender using two button head screws (2) and nuts (3). Tighten screws to 48 Nm (35 ft-lbs). Repeat for opposite side. 2. See Figure 5. Install release/attach weldment (1) to leave- on brackets (2) using two washers (3) and socket head cap screws (4). Tighten screws to 25 Nm (18 ft-lbs). Repeat for opposite side.

1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

KTM EXC 2004-2007 rear fender REMOVAL

0

Filed Under (KTM) by admin on 29-01-2012

download
Remove lower section of rear fender • Using care not to damage the threads, drill 1/8″ pilot hole up through subframe and rear fender (fig1) • Remove fender, enlarge pilot hole in upper subframe with 1/4″ drill, do not drill out threads- take care not to damage threads in subframe. • Enlarge holes in fender to 5/8″ • Install upper section of rear fender, insert enclosed 5/8″ spacers in fender holes (fig.2) • Install cross brace (bolt holes closer to front of bike) using enclosed M6 X 50mm button head bolt (fig 3) • Re-install lower fender section using original stepped washer with enclosed 6mm nuts (fig 4) • Install side brackets as shown in fig 5 – replace subframe bolts with enclosed flat head bolts at forward mounting points if necessary.

HARLEY DAVIDSON FRONT FENDER RAILS AND STANCHIONS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 03-03-2011

download
INSTALLATION 1. Carefully cut out appropriate template from sheet included in kit. One side is for FLSTS style fenders (with elliptical hole for front fender lamp), and the other side is for FLT style fenders (with rectangular front fender lamp). 2. Lay template on front fender (align around front fender lamp). 3. Underneath four holes marked on template, place high quality masking tape on fender. 4. Using a tape measure, measure from the top of the striping on the sides of each side of the fender, to the centerline of the each of the holes on the template (on some FLT models, with chrome fender trim, measure from the chrome fender trim at the bottom edge of the fender). Make sure that the distances are equal so that the template is centered on the fender. 5. Tape the template to the fender using high quality masking tape. NOTE Before proceeding, stand directly in front of the fender and carefully check to make sure the template is centered on the fender. 6. Center punch the center point of each of the four holes. 7. Remove the template from the fender. 8. Block motorcycle under frame so the front wheel is raised off the ground. 9. Follow appropriate Service Manual procedures and remove the front axle. 10. Place a rag on the top of the front brake caliper, then lower the front wheel so that it is resting on top of the brake caliper. NOTE When drilling fender holes, use care not to hit tire with drill bit. 11. While holding the fender firmly, and using caution to make sure that your drill bit does not hit the tire, drill the four holes at the points marked by the center punch. Begin with a 1/8 inch drill bit, followed by a 9/32 inch, and finally a 3/8 inch drill bit. 12. Remove the masking tape and any burrs that may have formed. 13. Remove the adhesive backing from each of the foam pads on the bottom of each of the stanchions. 14. Place the studs from each of the end stanchions into the holes (you may need to rotate the rails 180 degrees if they appear to be bowed out). 15. Reaching from the front of the fender, place kit washer, and then a locknut, over each of the studs on the underside of the fender. 16. Securely tighten each locknut so that the stanchion is firmly clamped to the fender. 17. Follow appropriate Service Manual procedures and replace the front wheel and axle