2004 yamaha raptor 350 wiring

You search Auto repair manual PDF 2004 yamaha raptor 350 wiring, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2004 yamaha raptor 350 wiring Direct Download speed 5282 Kb/s

  2004 yamaha raptor 350 wiring Full Version speed 6162 Kb/s



YAMAHA RAPTOR 350 Removing stock carburetor and cables

0

Filed Under (Yamaha) by admin on 18-01-2012

download
remove seat and gas tank. Make sure fuel petcock is in “off” position. 2. Remove throttle cable paying close attention to routing, as the new cable (s) will need too be routed the same. 3. Remove stock carburetor and stock throttle housing. Stuff a clean, dry rag into manifold to keep debris out of motor. 4. Remove stock air box. 5. Remove choke cable from handlebars. 6. Remove carb vent line from bike. Carburetor installation 1. Carefully trim the rubber alignment tab off of the face of the manifold with a razor blade or side cutters. 2. Remove the hex pipe plug from the carb cap using a 11mm or 7/16 wrench. Do not discard plug, as it will be needed later. Install the metering adjustment tool included in the hardware kit. Do not over-tighten as damage may occur to cap. 3. Attach fuel line to carburetor and secure with clamp. 4. Install remote idle cable into tab on top of carburetor. See main manual for this step. NOTE: Nut must be removed from cable before installation 5. Place carburetor into manifold

Incoming search terms:

1993-2004 Yamaha 350 Warrior Install Dynojet

0

Filed Under (Yamaha) by admin on 20-01-2012

download
Q406.002 This is Groove # 1 Fig. A Fig. B Mixture Screw Remove Slide Plate Screws Remove The Lift Arm Screw 1. Remove top carb plate. Remove the slide lift arm screw and the two needle plate screws. Flip the linkage forward and remove the slide (Fig. A). 2. Install Dynojet needle on groove #4 for applications below 5000 feet, groove #3 for above 5000 feet, using all stock spacers. 3. Remove the stock main jet and replace with the Dynojet main jet provided. If you are running the stock exhaust, use the DJ134 below 3000 feet, DJ130 from 3000 to 6000 feet and DJ126 above 6000 feet. If you are running an aftermarket exhaust, use the DJ136 below 3000 feet, DJ132 from 3000 to 6000 feet and DJ128 above 6000 feet. Be sure that the jet you are changing is the main jet. Discard the plastic cup that is on the stock main jet. 4. Locate the Fuel Mixture Screw (Fig.B). Using a flat blade screwdriver, turn the mixture screw clockwise until it seats, then turn out 2 1/2 turns.

2001 – 2004 Camry, Highlander, Solara & 2004

0

Filed Under (Toyota Manuals) by admin on 12-10-2011

download
2004 model year Camry, Highlander, Solara and 2004 model year RAV4 vehicles with the 2AZ-FE engine may exhibit squealing and/or rattling noises coming from the engine compartment during vehicle operation especially after a cold soak. The belt tensioner assembly has been improved to correct this condition. 2001 – 2004 model year Camry, Highlander and Solara vehicles equipped with 2AZ-FE engines produced BEFORE the Production Change Effective VINs shown below. 2004 model year RAV4 vehicles produced BEFORE the Production Change Effective VINs shown below. MODEL ENGINE LINE PRODUCTION CHANGE EFFECTIVE VIN TMMK Line 1 4T1BE3#K#4U358206 Camry TMMK Line 2 4T1BE3#K#4U914052 y 2AZFE Tsutsumi JTDBE3#K#40296732 Highlander 2AZ-FE TMK JTE#D2#A#40100501 Solara TMMK 4T1CE3#P#4U914074 RAV4 Tahara JTE#D2#V#40029797 PREVIOUS PART NUMBERCURRENT PART NUMBER PART NAME QTY 16620-28010 16620-28011 Tensioner Assembly, V-ribbed Belt 1 OP CODE DESCRIPTION TIME OFP T1 T2 EG8001 R & R Accessory Belt Tensioner 0.9 16620-28010 91 55 Applicable Warranty*: This repair is covered under the Toyota Comprehensive Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle’s in-service date. *Warranty application is limited to correction of a problem based upon a customer’s specific complaint

Incoming search terms:

SUZUKI SV 1000 RADIATOR (COOLING SYSTEM) SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
FI SYSTEM MALFUNCTION CODE AND DEFECTIVE CONDITION MALFUNCTION CODE DETECTED ITEM DETECTED FAILURE CONDITION CHECK FOR COO NO FAULT C11 Camshaft position sen- sor The signal does not reach ECM for more than 3 sec . after receiving the starter signal . The camshaft position sensor wiring and mechanical parts (Camshaft position sensor, intake cam pin, wiring/coupler con- nection) C12 Crankshaft position sensor The signal does not reach ECM for more than 2 sec . after receiving the starter signal . The crankshaft position sensor wiring and mechanical parts (Crankshaft position sensor, wiring/coupler connection) C13 Intake air pressure sensor The sensor should produce following voltage . (0.50 V < sensor voltage < 4 .85 V) Without the above range, C13 is indicated. Intake air pressure sensor, wiring/coupler connection C14 Throttle position sen- sor The sensor should produce following voltage . (0.20 V < sensor voltage < 4 .80 V) Without the above range, C14 is indicated. Throttle position sensor, wiring/coupler connection C15 Engine coolant temperature sensor The sensor voltage should be the following. (0.15 V <_ sensor voltage < 4 .5 V) Without the above range, C15 is indicated. Engine coolant temperature sensor, wiring/coupler connection C21 Intake air temperature sensor The sensor voltage should be the following. (0.15 V < sensor voltage < 4 .5 V) Without the above range, C21 is indicated. Intake air temperature sensor, wiring/coupler connection C22 Atmospheric pressure sensor The sensor voltage should be the following. (0.50 V < sensor voltage < 4 .5 V) Without the above range, C22 is indicated. Atm. pressure sensor, wiring/coupler connection C23 Tip over sensor The sensor voltage should be the following for more than 2 sec . after ignition switch turns ON . (0 .20 V < sensor voltage < 4 .80 V) Without the above value, C23 is indicated. Tip over sensor, wiring/coupler connection C24 or C25 Ignition signalCrankshaft position sensor signal is produced and ECM determines the ignition signal but signal from ignition coil is interrupted continuous by 4 times or more. In this case, the code C24 or C25 is indicated. Ignition coil, wiring/coupler connection, power supply from the battery SERVICING INFORMATION 8 .3 C28 Secondary throttle valve actuator No operating voltage is supplied from the ECM, C28 is indicated. STVA can not operate. STVA lead wire/coupler, STVA C29 Secondary throttle valve position sensor The sensor should produce following voltage . (0.10 V < sensor voltage < 4 .90 V) Without the above range, C29 is indicated . Secondary throttle position sensor, wiring/coupler connection C31 Gear position signalGear position signal voltage should be higher than the following for more than 2 seconds. (Gear position switch voltage >_ 0 .6 V) Without the above value, C31 is indicated. Gear position sensor, wiring/coupler connection, gearshift cam, etc. C32 or C33 Fuel injector Crankshaft position sensor signal is produced and ECM determines the injection signal but fuel injection signal is interrupted continuous by 4 times or more. In this case, the code C32 or C33 is indicated. Injector, wiring/coupler connection, power supply to the injector C41 Fuel pump relay No voltage is applied to fuel pump although fuel pump relay is turned ON, or voltage is applied to fuel pump although fuel pump relay is turned OFF . Fuel pump relay, connecting lead, power source to fuel pump relay C42 Ignition switchIgnition switch signal is not input in the ECM . Ignition switch, lead wire/coupler C44 Heated oxygen sensor (HO2S) [For E-02, 19] During 02 feedback control, 02 sensor voltage is higher or lower than the specification . No signal is detected during engine operation or no electrical power is supplied from the battery . HO2S lead wire/coupler connection Battery voltage supply to the HO2S C49 PAIR control solenoid valve (PAIR valve) When no operating voltage is supplied from the ECM, C49 is indicated. PAIR valve can not operate. PAIR valve lead wire/coupler

Incoming search terms:

CUSTOM LED 2004-2006 YAMAHA ROAD STAR INTEGRATED TAIL KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 10-11-2010

download
1 ) REMOVE THE SCREWS ON THE BACK SIDE OF THE TAIL LIGHT THAT HOLD THE CHROME TRIM TO THE TAIL LIGHT. 2 ) POSITION YOUR CUTTING WHEEL AS SHOWN IN THE PICTURE TO THE LEFT WHERE THE CLEAR PART OF THE LENS TURNS 90 DEGREES. THE CUTTING WHEEL SHALL REMAIN IN THE PLANE OF THE LENS. 3 ) PROCEED TO CUT INTO THE CLEAR LENS APPROXIMATELY HALF OF THE THICKNESS, ALL THE WAY AROUND THE PERIMETER OF THE LENS – BE SURE NOT TO CUT ALL THE WAY THROUGH BECAUSE IT WILL NOT GLUE BACK TOGETHER PROPERLY. SEE “TIPS FOR CUTTING YOUR LENS” BEFORE BEGINNING. TIPS FOR CUTTING YOUR LENS A) KEEP THE CUTTING WHEEL MOVING AND APPLY LIGHT PRESSURE. SITTING IN ONE SPOT WILL JUST MELT THE PLASTIC. WHEN YOU MAKE YOUR WAY AROUND THE ENTIRE PERIMETER, CLEAN ALL THE BURRED PLASTIC FROM AROUND THE EDGES AND FROM INSIDE THE GROOVE YOU’VE MADE. OPENING THE LENS 4 ) PLACE THE TIP OF A FLAT HEAD SCREWDRIVER IN THE GROOVE YOU HAVE CREATED. 5 ) GENTLY TWIST THE SCREWDRIVER TO CRACK THE GLUE ALONG THE GROOVE. NOTE: AS SOON AS YOU HEAR THE SOUND OF THE GLUE GIVING (A CRACK), MOVE THE SCREWDRIVER SLIGHTLY AND ADVANCE THE CRACK. SLOW AND STEADY IS THE NAME OF THE GAME HERE. IF YOU FIND A HARD SPOT, WEAKEN IT WITH THE CUTTING WHEEL AS NECESSARY. THE HARD PART IS OVER! YOU CAN RELAX NOW! 2 ©2005 Custom LED LLC. All Rights Reserved. 6 ) REMOVE THE SCREWS HOLDING THE STOCK LED BOARDS TO THE HOUSING (YOU WILL BE REUSING SOME OF THE SCREWS SO PUT THEM TO THE SIDE). 7 ) REMOVE THE STOCK LED ASSEMBLY FROM THE LENS HOUSING. YOU WILL NO LONGER NEED THE STOCK LED BOARD, DISPOSE OF IT AS YOU WISH. 8 ) GENTLY PRY OFF THE PLASTIC COVER TO EXPOSE THE DRIVER BOARD UNDERNEATH. 9 ) REMOVE THE SCREWS SUPPORTING THE DRIVER BOARD AND SNIP OFF THE THREE WIRES (BLUE, BLACK, YELLOW) AS SHOWN AS CLOSE TO THE CIRCUIT BOARD AS POSSIBLE! YOU WILL NEED TO CONNECT TO THESE WIRES LATER. 10 ) POP OUT THE LITTLE BLACK PLUG AS SHOWN IN THE PICTURE. YOU CAN POKE IT OUT FROM THE INSIDE OF THE HOUSING. WIRING UP YOUR CUSTOM LED BOARD PLACE YOUR CUSTOM LED INTEGRATED TAIL BOARD NEXT TO THE HOUSING AND MATCH THE WIRE COLORS AS FOLLOWS: TRY TO HANDLE THE CIRCUIT BOARD AS LITTLE AS POSSIBLE AS FINGERPRINTS AND DIRT WILL HINDER THE PERFORMANCE. • BLACK ON HARNESS TO 6″ BLACK ON CUSTOM LED BOARD • BLUE ON HARNESS TO 6″ BLUE ON CUSTOM LED BOARD • YELLOW ON HARNESS TO 6″ YELLOW ON CUSTOM LED BOARD USE THE THREE (3 OF 5) SUPPLIED ORANGE SPLICE CONNECTORS. PUSH THE TWO WIRES TO BE SPLICED TOGETHER INTO THE OPEN END. BE SURE TO PUSH THE WIRES ALL THE WAY IN (UNTIL YOU CAN SEE THEY HAVE REACHED THE OTHER SIDE). NOTE: YOU WILL NEED TO SEPARATE THE THREE WIRES FIRST BY CUTTING THE PLASTIC COLLAR THAT BINDS THEM. FOR THE WIRES TO FIT PROPERLY INTO THE CONNECTORS, YOU MUST ALSO REMOVE THE REMNANTS OF THE COLLAR FROM THE WIRES. NOTE: THE SPLICE IS MORE RELIABLE IF THE WIRE IS NOT STRIPPED. BE SURE TO SNIP OFF THE BARE ENDS OF THE WIRES ON THE CUSTOM LED TAIL TO ENSURE THAT THERE IS INSULATION WHERE THE SPLICE WILL OCCUR. THE SUPPLIED SPLICE CONNECTORS AUTOMATICALLY DISPLACE THE INSULATION AS NECESSARY. ONCE YOU DOUBLE CHECK YOUR COLOR MATCHING AND ARE ABSOLUTELY SURE THAT THE WIRES ARE FULLY INSERTED INTO THE SPLICE CONNECTORS DO THE FOLLOWING: 11 ) SQUEEZE THE SPLICE CONNECTORS FIRMLY WITH PLIERS. VISUALLY INSPECT YOUR CONNECTIONS TO SEE THAT THEY HAVE BEEN SPLICED PROPERLY INSIDE. 12 ) RUN THE GREEN AND BROWN WIRES THROUGH THE HOLE YOU OPENED UP IN STEP 9

YAMAHA MOTOR CORPORATION, U.S.A. STREET & ENDURO MOTORCYCLE LIMITED WARRANTY

0

Filed Under (Yamaha) by admin on 27-12-2011

download
GENERALEXCLUSIONS from this warranty shall include any failures caused by: a. Competition or racing use. b. Installation of parts or accessories that are not qualitatively equivalent to genuine Yamaha parts. c. Abnormal strain, neglect, or abuse. d. Lack of proper maintenance. e. Accident or collision damage. f. Modification to original parts. g. Damage due to improper transportation. SPECIFIC EXCLUSIONS from this warranty shall include parts replaced due to normal wear or routine maintenance. THE CUSTOMER’S RESPONSIBILITY under this warranty shall be to: 1. Operate and maintain the motorcycle as specified in the appropriate Owner’s Manual. 2. Give notice to an authorized Yamaha motorcycle dealer of any and all apparent defects within ten (10) days after discovery, and make the machine available at that time for inspection and repairs at such dealer’s place of business. You may locate your nearest authorized Yamaha dealer through your local telephone directory. WARRANTY TRANSFER: To transfer any remaining warranty from the original purchaser to any subsequent purchaser, it is imperative that the machine be inspected and registered for warranty by an authorized Yamaha motorcycle dealer. In order for this warranty to remain in effect, this inspection and registration must take place within ten (10) days after transfer. Areasonable dealer imposed fee may be charged for the inspection. In no case will warranty be extended beyond the original period. EMISSIONS CONTROLSYSTEM WARRANTY Yamaha Motor Corporation, U.S.A. also warrants to the ultimate purchaser and each subsequent purchaser of each Yamaha motorcycle covered by this warranty with a displacement of 50cc or greater, that the vehicle is designed, built, and equipped so as to conform at the time of sale with all U.S. emissions standards applicable at the time of manufacture and that it is free from defects in materials and workmanship which would cause it not to meet these standards within the periods listed immediately below. Failures other than those resulting from defects in material or workmanship which arise solely as a result of owner abuse and/or lack of proper maintenance are not covered by this warranty.

Incoming search terms:

YAMAHA YFM 350 Removing stock carburetor and cables.

0

Filed Under (Yamaha) by admin on 19-01-2012

download
Remove seat and gas tank. Make sure fuel petcock is in “off” position. 2. Remove throttle cable paying close attention to routing, as the new cable (s) will need too be routed the same. 3. Remove stock carburetor and stock throttle housing. Preparing motor for carburetor install 1. Remove stock manifold from cylinder head. 2. Place supplied o’ring into aluminum flange as pictured in figure 1. Figure 1. 3. Install aluminum and rubber flange to motor using supplied bolts. See Figure 2. The shorter 25mm bolt will need to be placed in the bottom hole. IMPORTANT NOTE: Install the aluminum flange with the o’ring towards the motor and the thick side up.

2003 – 2004 4Runner, 2004 Highlander, Prius, Sienna And Solara POWER WINDOW / ROOF INITIALIZATION PROCEDURES

0

Filed Under (Toyota Manuals) by admin on 17-10-2011

download
Turn the ignition switch ON. 2. Open the window halfway by pressing the power window switch. 3. Fully pull up the switch until the power window is fully closed and continue to hold the switch for at least three (3) seconds after the power window is fully closed. 4. Check that the “AUTO UP/DOWN” function operates normally. B. Back Door Power Window (4Runner) 1. Turn the ignition switch ON. 2. Open the back door glass. 3. Press the back door power window switch until the door glass is fully closed and continue to hold the switch one (1) second or more after the door glass is fully closed. 4. Check that the “AUTO UP/DOWN” function operates normally. C. Power Sliding Roof (4Runner, Sienna, Solara) 1. Turn the ignition switch ON. 2. Initialize the sliding roof by pressing and holding the TILT UP switch until the roof glass tilts upward fully (the roof glass automatically tilts downward slightly after fully tilting upward). 3. Release the switch. 4. Check that the “AUTO OPEN/CLOSE” function operates normally

2003 – 2004 4Runner & Tundra, 2004 Camry, Highlander, Sienna & SolaraREPAIR MANUAL SUPPLEMENT LEV II EVAP SYSTEM CHECK

0

Filed Under (Toyota Manuals) by admin on 24-10-2011

download
this TSB provides detailed instructions for a new LEV II EVAP System Check function using the Diagnostic Tester. The LEV II System Check allows the Diagnostic Tester to display the fuel tank vapor pressure as the EVAP VSV and the CCV are operated in a specific six-step pattern. Problems with the EVAP system are quickly isolated by observing the change in vapor pressure during each step. Once the vehicle condition is corrected, the LEV II System Check can also be used to confirm the repair before the vehicle is returned to the customer. The inspection procedure using the LEV II System Check (LEV II SYS CHECK) is described in this bulletin. This function is available using a Diagnostic Tester with version 11.0a software (or newer

TOYOTA SOLARA 1999-2004 VEHICLE WIRING

0

Filed Under (Toyota Manuals) by admin on 23-06-2011

Download
12V CONSTANT WIRE WHITE – WHITE/RED Ignition Harness STARTER WIRE RED Ignition Harness IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/RED Ignition Harness ACCESSORY WIRE BLUE/RED Ignition Harness POWER DOOR LOCK

Incoming search terms: