2005 c50 boulevard how pull trouble code

You search Auto repair manual PDF 2005 c50 boulevard how pull trouble code, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2005 c50 boulevard how pull trouble code Direct Download speed 5282 Kb/s

  2005 c50 boulevard how pull trouble code Full Version speed 6162 Kb/s



Suzuki C50/ M50 Boulevard BIG AIR KIT INSTALLATION

0

Filed Under (Suzuki) by admin on 13-03-2012

download
1. Remove the (2) Bolts at the top of the stock air cleaner to the left and right of the oval rubber hose coming from under the fuel tank. 2. Loosen the hose clamp at the base of the oval rubber hose on the top of the air cleaner. 3. A male barb protrudes from the rear of the air cleaner that inserts into a rubber grommet mounted to the cylinders. Pull the air cleaner away from the cylinders firmly and you will feel the barb release. Now pull the upper section of the air cleaner downward to remove it from the oval snorkel tube from under the fuel tank. 4. Now you can reach to the rear of the box and unplug the electrical lead for the Air Sensor” which sits just about in the middle of the rear of the air cleaner. Now remove the breather hose at bottom of the air cleaner. 5. Set the air cleaner aside and turn it over to access the back. Remove the single bolt that secures the Air Sensor” (This sensor will be installed into the Aluminum Manifold of your new BAK assembly later) 6. Remove the lower mounting arm assembly from the cylinders. (You will not reuse this). 7. Using the (2) Dome head m6 x 15mm screws install the (2) #1 Arms to the rear (the side without the groove) of the backing plate, the shiny/chrome side of the arms should face outward. The smaller of the two holes in each arm is the one you place the screws through. Use the m6 Flange Nuts to secure the bolts at the rear of backing plate. Snug these up but do not tighten fully.

Incoming search terms:

2004 – 2005 Camry, Highlander, And Solara, 2005 Matrix & Corolla PASSENGER AIRBAG INDICATOR LAMP

0

Filed Under (Toyota Manuals) by admin on 10-10-2011

download
passengers weighing approximately less than 100 pounds, depending on their seating position. It is important for the front seat passengers to know that proper operation of the advanced frontal airbag system is highly dependent on the pressure placed on the seat bottom. Situations that add or subtract sensed weight can result in occupant misclassification. To minimize this situation: Check seating posture. Passengers should be seated upright with their back against the seat back and feet on the floor. Check loading conditions. Extra weight from items, such as bags or groceries or toys, hanging on the seat back can add to the sensed weight of the front seat passenger. A rear seat passenger lifting the front seat with their legs, objects placed under the front seat, or the front seatback in contact with the rear seat can subtract from the sensed weight of the front seat passenger. If the passenger airbag indicator lamp continues to switch ON to OFF after checking the above conditions, perform the following repair procedure. NOTE: The safest place for children is in the rear seat. Please note that Toyota recommends that you never install a rear-facing child restraint in the front passenger seat, even if the passenger “Airbag OFF” lamp is illuminated. Please refer to you Owner’s Manual for additional details. 2004 – 2005 model year Camry, Highlander, and Solara vehicles produced BEFORE the Production Change Effective VINs shown on the following page. 2005 model year Matrix and Corolla vehicles produced BEFORE the Production Change Effective VINs shown on the following page

Incoming search terms:

2003 – 2005 Sequoia, 2004 – 2005 Highlander, Sienna, And Tundra DIAGNOSTIC GUIDE FOR REAR SEAT ENTERTAINMENT SYSTEMS

0

Filed Under (Toyota Manuals) by admin on 08-10-2011

download
Check the power, ground, and TX+, TX- wiring between the RSE ECU and the display. Perform the following check without disconnecting any connectors. A. Using the EWD, check the resistance of the wires between the DVD player ground terminal or integrated DVD player/RSE display and chassis ground. The resistance of the wires should be below 1 Ω. Refer to the Technical Information System (TIS): applicable model year Wiring Diagrams. B. Check the resistance of the wires between the RSE ECU ground terminal and chassis ground. The resistance of the wires should be below 1 Ω. C. Check the voltage on the power terminals on the DVD player and the RSE ECU. Voltage should be greater than 12 V. D. Check the voltage between terminals TX+ and chassis ground and TX- and chassis ground at both the RSE ECU and the DVD player. Voltage should be between 2.0 V and 3.0 V Check the resistance of the wires between the RSE ECU and the radio/player. The resistance of the wires should be below 1Ω. C. Check the resistance of the wires between the RSE ECU and the radio/player to ground. The resistance of the wires should be 10 kΩ or higher

2005 SUZUKI SV1000 SPECIFICATIONS AND SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
TIRE PRESSURE FUEL + OIL COLD INFLATION TIRE PRESSURE FRONT REAR SOLO RIDING ITEM Fuel type kPa 250 250 DUAL RIDING kPa 250 290 NOTE E-03, 28, 33 The others E-33 The others Fuel tank Engine oil type Engine oil capacity SPECIFICATfON Use only unleaded gasoline of at least 87 pump octane (R12 + M12) or 91 octane or higher rated by the research method. Gasoline containing MTBE (Methyl Tertiary Butyl Ether), less than 10% etha- nol, or less than 5% methanol with appropriate cosolvents and corrosion inhibitor is permissible. Gasoline used should be graded 91 octane or higher. An unleaded gasoline is recommended. 16 L (4.2/3.5 USnrnp gal) 17 L (4.513.7 USIlmp gal) * SAE 10W-40, API SFlSG or SHISJ with JASO MA kgf/cm2 2.50 2.50 Change Filter change Overhaul psi 36 36 kgflcrn2 2.50 2.90 2 700 rnl (2.912.4 USllmp qi) 2 900 ml (3.112-6 US/lmp qt) 3 300 ml (3.U2.9 USllrnp qt) psi 36 42 CRANKCASE-CRANKSHAFT BEARING SELECTION Select the specrffed bearings from the crankcase bore I. D. code. The crankcase bore I.D. code (A) “A, “6″ or “C”, is stamped on the inside of each crankcase half. Bearing selection table Bearing thickness I.D. code @9 A B C Bearing must be replaced as a set. I.P. specification 52.000 – 52.006 mrn (2.0472 – 2.0475 in) 52.006 – 52.01 2 mm (2.0475 – 2.0477 in) 52.01 2 – 52,018 mm (2.0477 – 2.0479 in) Color (Part No.) Green (1 2229-1 6GOO-OAO) Black (1 2229- tGG00-OBO) Brown (I 2229- 16GOO-OCO) Color code 9 Bearing Green Black Brown Thickness 1.999 – 2.002 mrn (0.0787 – 0.0788 in) 2.002 – 2.005 mm (0.6788 – 0.0789 in) 2.005 – 2.008 rnm (0.0789 – 0.0791 in) FI SYSTEM WIRING DIAGRAM I ECM TERMINAL (For KCModel) ‘& ECM TERMINAL (For K5-Model) FAIL-SAFE FUNCTION & FI system is provided with fail-safe function ta allow the engine to start and the motorcycle to run in a mini- mum performance necessary even under malfunction condition

2005 Kawasaki ZX6R Power Commander Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the tail section by removing the undertail and removing the six screws for the tail section. 2 Prop the front of the fuel tank up. 3 Lay the PCIIIin the tail section and route theharness along side the stock wiring harness towards the throttle bodies (Fig. B&C). Fig. A Fig. B Fig. C 2005 Kawasaki ZX6R – PCIII USB – 2 i218-411 www.powercommander.com PCIII harness PCIII harness Remove these screws 4. Disconnect the stock wiring harness from the LOWERinjectors at the throttle bodies (Fig. D). 5. Plug the PCIII connectors in-line of the stock injectors and wiring harness. ORANGE – cylinder 1 YELLOW- cylinder 2 GREEN – cylinder 3 BLUE – cylinder 4 6. Locate the Throttle Position Sensor connector behind the throttle bodies. This is a WHITE 3 pin connector (Fig. F) Fig. D Fig. E Fig F 2005 Kawasaki ZX6R – PCIII USB – 3 i218-411 www.powercommander.com PCIII connectors TPS connector Disconnect Stock connectors 7. Plug the PCIII harness in-line of the stock wiring harness (Fig. G). 8. Attach the ground wire from the PCIII to the negative side of the battery (Fig. H)

Yamaha 2005 R1 Bike Tech Sheet

0

Filed Under (Yamaha) by admin on 18-01-2012

download
Engine: Type: Liquid cooled, four stroke, transverse four cylinder, DOHC, 5 valves per cylinder. Displacement: 1000cc Year: 2005 Horsepower: 180hp Clutch: PM Exhaust: Vance & Hines Race Exhaust Mufflers: Vance & Hines Frame: Type: Stock Year: 2005 Swing Arm: Performance Machine Chromoly +4 Extended Shocks: Race Tech Modifications: Race Tech Tuned and Lowered. Forks: Stock lowered 2.5″ Rim: Performance Machine Contrast Cut Torque Size: 19″ X 3.0″ Finish: Contrast Cut Fender: None Tire: Dunlop Sportmax D208ZR 120/70ZR19 Brake: Dual Performance Machine 4 piston Radial Calipers Wheels Rear: Rim: Performance Machine Contrast Cut Torque Size: 18″ X 8.5″ Brake: Performance Machine 4 piston Radial Caliper Finish: Contrast Cut Tire: Dunlop Elite3 250/40/R18 Other Parts: Handlebars: Stock Foot Controls: Over Racing Seat: Stock Turn Signals F/R: Anything Extra? Mirrors: Performance Machine Torque chrome Mirrors 19″ FRONT WHEEL! Paint, Chrome, and other F/X’s: Colors: yellow/Black Type: Special Paint: AirTrix Industries The Painter: Chris Wood Powder Coating: A to Z Coatings

Corolla & Matrix 2005 – 2006 1ZZ-FE ENGINE NO START OR EXTENDED CRANK CONDITION

0

Filed Under (Toyota Manuals) by admin on 29-05-2011

Download
Some 2005 and 2006 model year Corolla and Matrix vehicles equipped with a 1ZZ–FE engine may exhibit a “no start” or “extended crank” condition. This may be caused by insufficient fuel pressure after the vehicle has been parked for a period of time. The fuel pump assembly manufacturing process has been improved to correct this condition. Applicable Vehicles S 2005 – 2006 model year Corolla and Matrix (2WD) vehicles equipped with the
1ZZ–FE engine. Parts Information PREVIOUS PART NUMBER 77020–02180 77144–04010 77169–02050 CURRENT PART NUMBER Same Same Same PART NAME Fuel Suction w/Pump & Gauge Tube Assembly Fuel Pump Gauge etainer
Fuel Suction Tube Set Gasket

2005 Honda CRF450X OWNER'S MANUAL AND COMPETITION HANDBOOK

0

Filed Under (Honda) by admin on 04-12-2010

download
Starting & Stopping the Engine Always follow the proper starting procedure described below. Your CRF can be started with the transmission in gear by pulling in the clutch lever before operating the kickstarter or start button. Preparation Make sure that the transmission is in neutral. Turn the fuel valve ON. Fuel Valve Starting Procedure Always follow the proper starting procedure described as follow. 5. Warm up the engine; don’t operate the throttle. 6. About 15 seconds after the engine starts, push the choke knob back all the way to fully OFF. If idling is unstable, open the throttle slightly. Extended use of the choke may impair piston and cylinder wall lubrication and damage the engine. HighAirTemperature 35°C (95°F) or above 1. Turn the fuel valve (1) ON. 2. Do not use the choke. 3. Keep the throttle fully closed. 4. Start the engine following step 4 under “Normal Air Temperature.” LowAirTemperature 10°C (50°) or below 1. If the temperature is below 32°F (0°C), open the throttle two or three times. (The engine requires a richer mixture for starting in cold weather. When the throttle is so opened, the accelerator pump will feed extra fuel to the cylinder, thereby facilitating starting in cold weather.) 2. Follow steps 1-5 under “Normal Air Temperature.” 3. Continue warming up the engine until it runs smoothly and responds to the throttle when the choke knob is pushed back all the way to fully OFF. Extended use of the choke may impair piston and cylinder wall lubrication and damage the engine. (cont’d) NOTICE NOTICE Basic Operating Instructions 15 (1) fuel valve The three-way fuel valve is used to control the flow of fuel from the fuel tank to the carburetor. ON -Turning the fuel valve ON before attempting to start the engine allows fuel to flow from the fuel tank to the carburetor. OFF -Turning the fuel valve OFF prevents the flow of fuel from the fuel tank to the carburetor. RES -Turning the fuel valve to RES allows fuel to flow from the reserve fuel supply to the carburetor. (1) fuel valve (2) choke knob Check the engine oil, transmission oil and coolant levels before starting the engine (pages 44,47,48). To restart a warm engine, follow the procedure for”High Air Temperature.” NormalAirTemperature 10°C-35°C (50°F-95°F) 1. Turn the fuel valve (1) ON. 2. Pull the choke knob (2) fully ON, if the engine is cold. 3. Keep the throttle fully closed. 4. Pull the clutch lever all the way in, and depress the start button. Or operate the kickstarter to start the engine. Starting from the top of the stroke, kick through to the bottom with a rapid, continuous motion. Do not operate the throttle. Allowing the kickstarter to snap back freely against the pedal stop can damage the engine

Incoming search terms:

BMW 3 SERIES INSTALLATION MANUAL

0

Filed Under (BMW) by admin on 17-11-2010

download
1. Turn off the ignition and disconnect the negative battery cable. NOTE: Disconnecting the negative battery cable erases pre-programmed electronic memories. Write down all memory settings before disconnecting the negative battery cable. Some radios will require an anti-theft code to be entered after the battery is reconnected. The anti-theft code is typically supplied with your owner’s manual. In the event your vehicles’ anti-theft code cannot be recovered, contact an authorized dealership to obtain your vehicles anti-theft code. TO START: 2. Depress the wire-locking clip and disconnect the mass air sensor electrical. BMW 3 SERIES (E46) 1999-00 323i, ci 1999 323iC 2001-05* 325i, ci L6-2.5L 1999-00 328i 2000 328ci 2002-05 325xi L6-2.8L NOTE: * Excluding 2003 & 2005 PZEV model with engine family 3BMXV02.5M56 & 5BMXV02.5M56 Flat Blade Screwdriver Ratchet Extension 10mm Socket 10mm Wrench 4mm Allen A intake tube (EL) 1 087139 B hose ; 4mm id x 2″ l 1 08062 C npt fi tting; 1/4″ x 5/16″ barb 1 08908 D hose clamp #48 3 08601 E silicone hose 3.25″id x 2″l 1 08690 F nut; 6mm nylock 7 07553 G washer; 1/4″id x 5/8″od fl at 7 08275 H washer; 1/4″ split lock 1 08198 I bolt; 6mm-1.00 x 16mm, b/h/a 2 07730 J bolt; 6mm-1.00 x 12mm, b/h/a 4 07794 K washer; 1/4″id x 1″od fender 2 08160 L bracket 1 010087 M heat shield “A” 1 07492 N heat shield “C” 1 07497 O heat shield “B” 1 07494 P edge trim 46″L 1 102487 Q air fi lter 1 RU-4730 3. Pull up on the four fresh air duct-retaining pins to release them from the radiator core support. 4. Lift up and remove the fresh air duct from the vehicle as shown. NOTE: Disconnect the fresh air tube from the fresh air duct. 5. Loosen the hose clamp which secures the intake tube to the mass air sensor, and then disconnect the intake tube from the mass air sensor as shown. 6. Remove the two-factory air box mounting bolts shown.

2004-2005 Harley Davidson Dyna EFI Tuner Installation Manual

0

Filed Under (Harley Davidson) by admin on 14-04-2012

download
1 Remove the seat 2 Remove the left hand side cover (Fig. A). 3 Unplug the stock wiring harness connector from the ECM (Fig. B). 4 Move the data plug (Fig. B) out of the way to access bolt. 5 Remove the 3 bolts that hold the electrical box in place (Fig. B). 6 Slide the plastic box out from the frame. 7 Route the stock connector through the box and into the small opening in the frame (Fig. C). Fig. A Fig. B Fig. C Remove side cover Stock connector Stock connector Data plug Remove bolt Remove bolts FM810 www. fuelmotousa.com 2004-2005 Harley Davidson Dyna – FM EFI Tuner – 2 8 Plug the black connector of the Power Commander into the stock wiring harness connector (Fig. D). 9 Route the grey connector of the Power Commander through the box and plug it into the ECM. 10 Install the Power Commander against the rear part of the electrical box. Make sure to clean both surfaces with the alcohol swab first. Use the supplied velcro to attach the Power Commander. 11 Bolt the box back into place. 12 Reinstall the seat. Fig. D Fig.

Incoming search terms: