2005 harley twin cam 88 problems

You search Auto repair manual PDF 2005 harley twin cam 88 problems, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2005 harley twin cam 88 problems Direct Download speed 5282 Kb/s

  2005 harley twin cam 88 problems Full Version speed 6162 Kb/s



Harley-Davidson Twin Cam Engines Cam Chain Drive System Installation and removal MANUAL

0

Filed Under (Harley Davidson) by admin on 27-03-2012

download
Removing the Cam Chain Drive System. NOTES Changing camshafts and cam drives in the 2006-up Harley-Davidson® Twin Cam 88® engines is different than in pervious engines. Procedures require use • of some special tools. Installation should be done by an experienced mechanic with access to factory service manual and required tools. Tighten all fasteners to the correct specifications and in order described. Always use an accurate torque wench. • Incorrect installation can cause engine damage not covered under warranty. CAUTION Failure to install components correctly can result in sudden engine seizure. Engine seizure may result in serous injury to motorcycle operator, passenger, or others. A- Disconnect the battery ground cable to eliminate potential sparks and inadvertently engagement of the starter while working on the motorcycle. B- Remove spark plugs and pushrod cover clips. Collapse the pushrod covers to expose the pushrods. C- Safely elevate and stabilize the rear of the motorcycle. Place the transmission in high gear. Turn the rear wheel to rotate the engine until both lifters and pushrods for either cylinder are at the lowest point on the camshaft (TDC of compression stroke). Both intake and exhaust pushrods for that cylinder will be under pressure from the valve springs and will rotate with light finger pressure. NOTE: 510G camshafts may use stock style non-adjustable pushrods instead of adjustable pushrods. If installing non-adjustable pushrods, disassemble and assemble rocker boxes per H-D® instructions. All other S&S® gear driven cams require installing adjustable pushrods. As a time-saving measure, the stock pushrods can be removed with bolt cutters. Be sure to head caution and warnings of these instructions. D- Cut the pushrods for the cylinder that is at TDC with the bolt cutter and remove the pushrod covers from the engine. Rotate the engine to place the pushrods for the other cylinder at their lowest point. Cut and remove the remaining pushrods. WARNING CAUTION Cutting pushrods with a saw or cutoff wheel may result in debris entering the engine, causing engine damage not covered under warranty. WARNING Cutting pushrods without releasing spring pressure, by rotating the engine until tappets are at the lowest point of travel can result in bodily injury. E- Remove the pushrod covers and lifters form the crankcase. F- Remove engine cam cover and gasket. Secure lifers with a tool made from a large binder clip

Incoming search terms:

Harley-Davidson Big Twin Evolution and Twin Cam Edelbrock/ JE Sport INSTALLATION INSTRUCTIONSsman Pistons

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
INSTALLATION PROCEDURE Note: All Evolution® “Big Twin” pistons are marked “Front” or “Rear” and come with rings, wrist pins, and locks. • Note: We highly recommend that a dealer or trained mechanic perform the installation of these pistons. Specialized equipment is required for honing and finishing the cylinders to ensure long life of the piston and cylinder assembly. 1. Remove original equipment cylinders from engine. Refer to a shop manual or other reference book for specific steps, if needed. (Note: Care should be taken not to bend the studs or damage the cylinder during removal of the cylinders.) 2. With a small screwdriver, move the wrist pin retainer around to gain access to the tail of the retainer as it lines up with the notch in the bottom of the wrist pin hole. 3. Use a small screwdriver, pick or awl to roll the wrist pin retainer out of its groove. 4. Push wrist pin out and remove piston. 5. Repeat procedure for the other piston. 6. At this point, take cylinders, new pistons, and piston-to-wall clearance specifications to your dealer or machine shop to perform necessary machining operations. • IMPORTANT NOTE (Evolution® and Twin Cam®): The cylinder bore must be machined/honed to provide .0025″ of piston-to-wall clearance. Measure the piston diameter at a point .500″ up from the lower skirt (See Figure 3). 7. Starting with the front cylinder, install new piston rings and one wrist pin retaining clip (Note: Second ring has a dot which must face up when the ring is installed) . 8. Place the piston over the conecting rod, making sure that the intake valve pocket is towards the intake side. (For Evolution ® , see Figure 1. For Twin Cam ® , see Figure 2) . Coat the wrist pin with engine oil and insert it into the piston. Install the second wrist pin retainer into the groove. 9. Lightly coat the piston skirt with engine oil. Place a piston ring compressor over the piston/ring assembly and compress. Place the cylinder over the piston and gently push down until all rings are in the cylinder. Remove the ring compressor, and push the cylinder the rest of the way down. (Note: Be careful not to get oil onto the base gasket.) 10. Place two nuts and washers on opposite corners of the #1 cylinder to hold it down while you repeat the procedure for cylinder #2. 11. Assemble the rest of the engine per factory specifications. Start the engine and let it run at 2000 rpm for about 10 minutes.

Incoming search terms:

HARLEY DAVIDSON HYBRID CAM PLATE AND HIGH FLOW OIL PUMP KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. Gasoline can drain from the carburetor fuel line when disconnected from fuel valve fitting. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00256a) NOTES Installing this kit requires removal and installation of the cam support plate. Refer to the service manual for instructions with the following exception pertaining to cam compartment compo- nents: The crank and primary cam sprocket flange bolts are specially hardened, and the flat washers are of a special diameter and have ground surfaces. Use ONLY the parts provided in the Drive Gear Retention Kit (H-D Part Number 25533-99A, sold separately) when installing this kit. -J04804 1 of 7
The cr ank sprocket flange bolts and pr imary cam sproc ket flange bolts ARE NOT interchangeable. 2. Refer to the service manual to remove and discard the crank sprocket flange bolts and primary cam sprocket flange bolts and washers. 3. For 1999 models only: Refer to the service manual to remove and discard the currently installed cam drive sprocket. 4. Refer to the service manual to remove and disassemble the cams from the support plate and oil pump. Discard the support plate and oil pump. 5. For 1999 – 2000 Dyna, 2000 Softail, 1999 – 2000 Touring, and 2001 EFI Touring models only: Inspect the cams, chain, sprockets and chain tensioners for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. For 2001 – 2005 Dyna, 2001 – 2006 Softail, 2002 – 2006 Touring, and 2001 carbureted Touring models only: Inspect the cams and secondary cam chain for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. The primary cam chain, primary sprockets and both tensioners will be replaced by new components from the kit. For ALL models and years: Discard the guide, as it will not be used. INSTALLATION 1. ALL models: See Figure 1. Obtain the new Rear Cam Roller Bearing Kit (H-D Part Number 8983) from inside the Cam Service Kit (H-D Part Number 17045-99C, purchased separately), and install as indicated in Step 2. NOTE See Figure 2. If not enough of the splined shaft is exposed to install the sprocket, omit the spacer (4) and proceed to Step 2e. When the bearing inner race is started onto the machined area, remove the flange bolt (5), flat washer (6) and sprocket, then assemble using the spacer (4). Repeat Step 2e to fully install bearing inner race. To center thrust washer, be sure o-ring is installed in relief groove. Damage to bearing cage and engine can occur if thrust washer is not centered. (00473b) 2. See Figure 1. Install the O-ring (5), thrust washer (4) and bearing inner race (3) onto the rear camshaft as follows: a. See Figure 2. To properly locate the thrust washer (2), install the O-ring (3) in the grinding relief groove on the splined end of the rear camshaft between the machined area and the secondary cam sprocket.

Incoming search terms:

Harley-Davidson Twin Cam Engines Performer RPM Gear Drive Camshaft Kit INSTALLATION PROCEDURE

0

Filed Under (Harley Davidson) by admin on 03-03-2012

download
1. Disconnect the battery, and remove the fuel tank. 2. On engines with the oil tank above the engine, drain the engine oil. 3. Remove the front exhaust pipe to clear the Cam Housing Cover. 4. Remove the Rocker Covers and remove the four 5/16″ bolts and the two 1/4″ bolts holding the rocker arms in place. With the rocker arms removed, remove the stock pushrods. 5. Remove the push rod tube retaining clips and push rod tubes. 6. At this point, you may remove the lifter covers and take the lifters out, or you can make a lifter holding tool from a binder clip as shown in Figure 1 INSTALLATION PROCEDURE 1. Disconnect the battery, and remove the fuel tank. 2. On engines with the oil tank above the engine, drain the engine oil. 3. Remove the front exhaust pipe to clear the Cam Housing Cover. 4. Remove the Rocker Covers and remove the four 5/16″ bolts and the two 1/4″ bolts holding the rocker arms in place. With the rocker arms removed, remove the stock pushrods. 5. Remove the push rod tube retaining clips and push rod tubes. 6. At this point, you may remove the lifter covers and take the lifters out, or you can make a lifter holding tool from a binder clip as shown in Figure 1 . 7. On pre-2000 models with a cam position sensor, you may want to remove the inspection cover, unplug the wires, and remove the sensor at this time to ease installation later on. 8. Remove the cam housing cover keeping the bolts in a separate cup. ( Note: Oil will run out of the cam housing.) 9. Using the Chain Tensioner Unloader Tool, unload pressure on the outside chain tensioner, and pin it in place with the retaining pin (See Figure 2) .

Incoming search terms:

HARLEY DAVIDSON SCREAMIN' EAGLE TWIN CAM 103 (1690 CC) CONVERSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
REMOVAL When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 1. Remove maxi-fuse. Refer to MAXI-FUSE INSTALLATION in Service Manual. 2. Remove existing air cleaner assembly. Discard filter element, backplate, and air cleaner cover insert but save remaining parts. Refer to AIR CLEANER REMOVAL in Service Manual. 3. Remove existing exhaust system. Discard mufflers but save remaining parts for kit installation. Refer to EXHAUST SYSTEM REMOVAL in Service Manual. 4. Remove engine from chassis following the instructions in the Service Manual. 5. Remove induction module. Refer to appropriate FUEL INJECTION section in Service Manual. 6. See Figure 1. Remove and save screw (with pilot sleeve) to release fuel supply tube clamp. is03165 Figure 1. Fuel Supply Tube Clamp Screw 7. See Figure 2. Pull fuel supply tube (1) from fuel rail. -J03825 1 of 10 1 2 3 3 4 is03166 1. Fuel supply tube 2. Sealing washer 3. O-ring 4. Screw (with pilot sleeve) Figure 2. Fuel Supply Tube Assembly 8. Remove sealing washer (2) and O-ring (3) from fuel supply tube. Remove second O-ring (3) from fuel rail bore. Discard sealing washer and O-rings. 9. See Figure 3. Pull fuel injectors (1) with attached fuel rail from induction module. To overcome the resistance of the bottom O-ring (2) on both fuel injectors, gently rock assembly back and forth while pulling. 10. Remove spring clips (3) from fuel injectors. Pull fuel injectors from fuel rail. To overcome the resistance of the top O-ring (4) on both fuel injectors, gently rock assembly back and forth while pulling. 11. Disassemble engine top end, engine bottom end, crankcase, and crankshaft. Refer to appropriate ENGINE sections in Service Manual. 1 2 4 3 is03167 1. Fuel injector 2. O-ring, bottom 3. Clip, spring 4. O-ring, top Figure 3. Fuel Injector Assembly INSTALLATION Inspect Cam Clearance A clearance problem between the new cam lobe and crankcase housing may exist on certain older model engines. Failure to maintain proper clearance could result in severe engine damage. (00391b) 1. See Figure 4. Prior to starting assembly procedures, insert new cams from kit into inner needle bearings (1) located in the right side crankcase and check for a minimum of 0.030 in. clearance between highest lift point of cam lobes and crankcase housing (2) with feeler gauges. NOTE If inadequate clearance is detected, crankcase housing must be machined to provide 1.060 in. Radius clearance from center of each cam bearing bore. After machining, recheck for minimum of 0.030 in. clearance

HARLEY DAVIDSON NOSTALGIC TWIN CAM 88 AIR CLEANER COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-02-2011

download
INSTALLATION 1. Remove current air cleaner cover and screw. 2. See Figure 1. Coat threads of screw (1) from kit with Loc- tite® 243 (blue) (Harley-Davidson part number 99642-97). Install new air cleaner cover (2) with screw (1). If this kit will be installed with a Screamin’ Eagle Twin Cam 88 high flow air cleaner kit, place the self adhering gasket (must be purchased separately) inside the cover between the air filter and the cover. Tighten screw to 36-60 in-lbs (4.1- 6.8 Nm)

HARLEY DAVIDSON SCREAMIN' EAGLE TWIN CAM 110 (1800 CC) CONVERSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
REMOVAL Prepare for Service 1. Position motorcycle on a suitable lift. NOTE If vehicle is equipped with Harley-Davidson Smart Security System, see owner’s manual for instructions to disarm the system. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect battery cables, negative (-) battery cable first. 3. Remove seat according to the instructions in the service manual. 4. Refer to service manual to remove left saddlebag and side cover. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 5. Remove fuel tank according to the instructions in the service manual. Remove Engine Components 1. Remove existing air cleaner assembly. Discard backplate but save remaining parts. Refer to AIR CLEANER REMOVAL in service manual. 2. Remove existing exhaust system. Refer to EXHAUST SYSTEM REMOVAL in service manual. 3. Remove engine from chassis following the instructions in the service manual. 4. Disassemble engine top end and bottom end. Refer to appropriate ENGINE sections in service manual. 5. Remove existing clutch diaphragm spring. Refer to CLUTCH REMOVAL in service manual. The procedures in this instruction sheet should be performed by one experienced in precision measuring techniques. Failure to meet tolerances called for in this instruction sheet can result in engine damage. (00511b) -J04793 1 2 is03517 1. O-ring counterbore 2. Spigot bore Figure 1. Spigot Bore and O-Ring Counterbore Dimensions Table 1. Spigot Bore and O-Ring Counterbore Dimensions Depth Bore Description 1.625 +/- 0.010 in. (41.3 +/- 0.25 mm) 4.205 +/- 0.010 in. (107 +/- 0.25 mm) Spigot Bore 0.085 +/- 0.003 in. (2.16 +/- 0.08 mm) 4.415 +/- 0.002 in. (112 +/- 0.05 mm) O-Ring Counter- bore is03456 Figure 2. Cylinder Wall MACHINE CRANKCASE Crankcase Boring Preparation NOTE During final assembly of the engine, Harley-Davidson recommends replacing the OE cylinder studs with Screamin’ Eagle High Tensile Studs (16505-01). 1. Remove cylinder studs from the engine crankcase. 2. Mask off all bearings and oil holes to prevent debris and contaminants from entering those areas. 3. Inspect and clean engine case mating surfaces. 4. See Figure 6. Reassemble engine case with OE screws, except the top center screw between the cylinders, and tighten to specifications listed in service manual. NOTE To prevent damage to crankcase boring tool, it is important to replace the top center screw with a modified top center screw (1093). This screw is included in the Crankcase Boring Tool Kit (94419-06) and can be purchased separately from a Harley- Davidson dealer. 5. Install modified top center screw (1093) between the cylinders and tighten to 50-90 in-lbs (5.6-10.2 Nm). 6. See Figure 1 and Table 1. Machine crankcase cylinder spigot bore and O-ring counterbore to the dimensions shown. Modify Crankcase

Incoming search terms:

Yamaha YZ 250F Camshafts REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 30-12-2011

download
Remove the 4 bolts that hold the exhaust cam cap in place, lift the cam cap off. It may be necessary to pry very lightly on the cap to lift it off its dowel pins. Do not use the cam lobes as the pry point. Be careful not to drop the dowels and also be careful to not lose the half moon shaped retainer for the bearing under the cam cap. Remove the 6 bolts that hold the intake camshaft cap and lift the cam cap off the camshaft, again, be careful to not drop the retainer or dowels. Lift the intake camshaft out of its pocket in the cylinder head casting. Remove the cam chain from the sprocket, set the stock camshaft aside. Lift the exhaust cam out of its pocket in the cylinder head casting and remove the chain from the sprocket. Do not drop the cam chain, dangle it over the side of the engine while keeping slight upward pressure on the chain to maintain its position on the drive sprocket on the crankshaft. Fit the half moon shaped retainers in the grooves of the Hot Cams camshaft bearings to ensure good fit, set retainers aside for the time. Using assembly lube, lube the shim buckets, bearing surfaces for the camshafts in the cylinder head, and pack some in the camshaft bearings. Set the exhaust cam into the cylinder head casting while at the same time fitting the cam chain over the sprocket. Make sure that you keep all the cam chain slack to the back of the engine. The cam chain pulls the camshaft sprockets in a counter clockwise direction and the slack of the chain must be kept on the cam chain tensioner side of the engine. The exhaust cam has two timing marks on it. When correctly installed one mark will be at the 9 o’clock position and the other mark will be at the 12 o’clock position. When correctly timed the mark at 9 o’clock will be aligned with the valve cover gasket surface. Repeat the above process for the intake camshaft. Again, make sure you keep the chain slack to the cam chain tensioner side of the engine. Check to be sure the crankshaft is still at TDC. The intake cam has two timing marks also. One at 12 o’clock and the other at 3 o’clock. When both cams are installed correctly, the valve cover gasket surface will form a straight line through the exhaust timing mark at 9 o’clock and the intake timing mark at 3 o’clock

Incoming search terms:

HSR Carburetor Total Kits Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
Intake Manifold: 1. Install MAP sensor in Mikuni manifold (Twin Cam only). 2. Attach the Mikuni manifold to the engine. Align the manifold before tightening the bolts. The flange surface of the Mikuni manifold should be parallel with the front of the engine’s cam cover. Use a level or angle meter to check this. Tighten the manifold bolts. 3. Attach the rubber flange to the Mikuni manifold with the furnished 5/16″x3/4″ bolts and washers. Choke Cables: Mikuni & Harley-Davidson Route the cable with largest radius bends possible. Check the cable for free-play after installation. If there is no free-play, the engine may run rich and deliver poor performance or low fuel mileage. Harley Cable (Twin Cam Kits: 42-19, 45-4) : 1. Remove the Harley choke cable from the stock carb. 2. Remove the spring and plunger from the cable. 3. Remove the spring and plunger from the Mikuni. 5. Install the Mikuni spring and plunger onto the Harley choke cable. Change nothing else; be sure to use the Harley plastic nut, not the Mikuni nut (See Figure 1). Total Kit Installation Instructions The HSR series carburetors are precise yet durable instruments; however, like any other piece of fine equipment, they require correct installation and reasonable care to assure optimum performance and long life. Extra time spent during installation will pay off in both short and long term performance and reliability. This Mikuni HSR carburetor kit is designed to be a bolt-on application, and as such, is set-up and jetted properly for most applications. However, since Harley-Davidson motors are often highly modified, alternate tuning settings may be required. The Mikuni Tuning Manual helps make jetting alterations and adjustments an easy matter. NOTE: Carburetor Kits not designated as C.A.R.B. exempt, are not legal for motor vehicles operated on public highways in the state of California, or in any other states and countries where similar laws apply. WARNING NOTE: NOTE: WARNING CAUTION NOTE: NOTE: TK-2 6. Install the new assembly into the Mikuni carburetor. Be careful to only gently tighten the plastic nut. 7. Loosen the knurled plastic friction nut behind the choke knob and check for free-play (see Figure 2). Figure 1: Harley nut with Mikuni spring & plunger Figure 2: Choke cable adjustments Mikuni Cable (Evo Kits: 42-8, 45-2 & 45-3) : 1. Remove nut, spring and plunger from the Mikuni. 2. Install the nut, spring and plunger onto the cable. 3. Install the assembly into the Mikuni HSR carburetor. Be careful to only gently tighten the plastic nut. 4. Check for free-play. Adjust the cable as necessary. An optional choke cable mounting bracket is included in the Evo kits for custom installations. Carburetor Installation: 1. Insert the carb fully into the rubber flange, align with engine and tighten the clamp. 2. Slip the fuel hose onto the carburetor’s fuel fitting and secure with the enclosed hose clamp. NOTE: Some Twin Cam installations may require removal of a small amount of fin material from the cylinders to clear the float bowl. Throttle Cables The HSR carburetor uses stock 1990 and later Harley- Davidson cables. However, if your Harley is fitted with some other carburetor, you may need to purchase a set of cables. See your dealer for the correct cable set. 1. Route the throttle cables with large radius curves and so they do not interfere with other components. 2. Screw the cable adjusters together to make them as short as possible. 3. Connect the “close” cable first (see Figure 3). 4. Install the “open” cable next (see Figure 3). 5. Adjust the opening cable until the slide can be opened fully. Snug the adjuster lock nut. 6. Turn the handlebar to the right and adjust the throttle free-play with the closing cable adjuster to approximately 1/8″ (see Figure 4)

Incoming search terms:

Yamaha YZ400/426F Camshafts REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 01-01-2012

download
Cleanliness is always a good place to start. Make sure the motorcycle is cleaned thoroughly before you start. It would be advisable to use an engine degreaser on the frame and the engine. This will ensure a clean engine during the assembly process and less of a chance of thread damage and/or dirt contamination in the engine during reassembly. And as always, replace any fiber-based gasket that was moved in any way, i.e.: cam chain tensioner. You will need basic hand tools and a torque wrench, machine towels (rags), some cleaning solvent, and a cam chain tensioner gasket. And the Hot Cams’ Degree Wheel Kit if you so desire. We will start by removing the tank and seat, top engine mount, and the cam cover. Remove the crankshaft cap and timing hole cap on the left engine case cover. Remove the spark plug. Rotate the engine in a counter clockwise (CCW) direction. Position the engine on top dead center (TDC) using the mark on the flywheel or better yet a degree wheel using a positive stop. Be sure to notice that the intake valves were the last to move, this will ensure the engine of being on “true” TDC. True top dead center occurs when both the intake and exhaust valve are closed when the piston is at TDC. This is technically the end of the compression stroke and the Page 1
beginning of the power stroke. The “artificial” TDC is during the overlap when both the intake and exhaust valves would be open. Note the positioning of the cam lobes (their included angle will be close to 170 degrees), this will help during the installation of your new Hot Cams camshafts Remove the cap bolt on the end of the cam chain tensioner block, be aware of the copper washer. Release the spring tension on the cam chain tensioner by turning the flat blade screw slot inside the adjuster block in a clockwise (CW) direction; it will lock in the retracted position. Remove the two 8mm headed bolts that hold the cam chain tensioner to the cylinder block. Remove and discard the gasket. Remove the 4 bolts that hold the exhaust cam cap in place, lift the cam cap off. It may be necessary to pry very lightly on the cap to lift it off its dowel pins. Do not use the cam lobes as the pry point. Be careful not to drop the dowels and also be careful to not lose the half moon shaped retainer for the bearing under the cam cap. Remove the 6 bolts that secure the intake cam cap and lift the cam cap off the camshaft, again, be careful to not drop the retainer or dowels. Lift the intake camshaft out of its pocket in the cylinder head casting. Remove the cam chain from the sprocket, set the stock camshaft aside. Lift the exhaust camshaft out of its pocket in the cylinder head casting and remove the chain from the sprocket. Do not drop the cam chain, dangle it over the side of the engine while keeping slight upward pressure on the chain to maintain its position on the drive sprocket on the crankshaft

Incoming search terms:

Incoming search terms: